Ir配合物染料调节有机发光二极管发光特性

为了研究有机发光二极管(OLED)中发光特性与材料能带结构的关系,把不同的Ir配合物染料掺杂到结构相同的OLED器件中。OLED结构为ITO/NPB/CBP∶染料/TPBi/Mg∶Ag/Ag,染料分别为Ir(MDQ)2(acac)、Ir(ppy)3和Firpic。实验表明,这3种染料对应的掺杂器件分别发红光、绿光和蓝光。3个器件的阈值电压基本一致((6为了研究有机发光二极管(OLED)中发光特性与材料能带结构的关系,把不同的Ir配合物染料掺杂到结构相同的OLED器件中。OLED结构为ITO/NPB/CBP:染料/TPBi/Mg:Ag/Ag,染料分别为Ir(MDQ)₂(acac)、Ir(ppy)₃和Firpic。实验表明,这3种染料对应的掺杂器件分别发红光、绿光和蓝光。3个器件的阈值电压基本一致((6±0.1) V),但是,在100 cd/m²亮度下,绿光器件外量子效率最高(7.64%),蓝光器件外量子效率(5.65%)与绿光相近,红光器件外量子效率最低(2.75%)。分析认为,由于染料的掺杂浓度低,器件结构和载流子传输特性变化小,因而掺杂对阈值电压影响小;CBP与掺杂染料间存在能量转移,红色染料能级差小,非辐射跃迁几率大,发光效率最低;相比于绿光,蓝色染料能级差大,跃迁几率小,因此发光效率比绿光低。实验还发现,染料的发光波长与其能级差相比有红移现象,分析认为,这是由激发态能量振动弛豫和系间窜越过程形成的。     

Ir(ppy)3掺杂PVK体系发光特性的研究

对常温下磷光染料Ir(ppy)3掺杂PVK薄膜的光致发光(PL)和电致发光(EL)特性进行了研究。器件结构为ITO/PEDOT:PSS/PVK:Ir(ppy)3/BCP/Alq3/Al。实验发现随磷光材料掺杂浓度的不同,器件的发光性能发生变化。当浓度适宜时,主体材料PVK的发光很弱,主要为Ir(ppy)3的磷光发射。通过L-I-V特性曲线的比较,掺杂浓度为5%的光电性能最好,说明器件在掺杂浓度为5%时效果最佳。     

非掺杂型高效绿色磷光有机电致发光器件

在空穴传输层TCTA与电子传输层TPBi之间引入磷光染料Ir(ppy)3超薄发光层,制备了结构为ITO/MoO_3(2 nm)/NPB(40 nm)/TCTA(10 nm)/Ir(ppy)3(xnm)/TPBi(40 nm)/LiF(1 nm)/Al(80 nm)的非掺杂磷光有机电致发光器件。通过调控非掺杂发光层的厚度,详细研究了Ir(ppy)3层厚度对器件性能的影响。实验结果表明,当非掺杂发光层厚度为0.2 nm时,器件的性能最好,器件的亮度、效率和外量子效率分别达到26 350 cd·m~(-2)、42.9 cd·A~(-1)和12.9%。研究结果表明,采用超薄的非掺杂发光层可以简化器件结构和制备工艺,获得高效率的OLED器件。     

深陷阱对有机磷光双掺杂体系电致发光器件效率衰退的影响

研究利用溶液法制备的有机磷光双重掺杂体系电致发光器件的光致发光特性与电致发光特性,并研究了在这种体系中深能级陷阱导致的器件效率衰退现象。首先利用紫外光谱仪和光致瞬态寿命测试系统对基于旋涂法制备的以宽带隙材料4,4’-bis(N-carbazolyl)-1,1’-biphenyl（CBP）为主体,绿色磷光材料tris(2-phenylpyridine) iridium(Ⅲ)（Ir(ppy)₃）和红色磷光材料tris(1-phenylisoquinolinato-C2,N)iridium(Ⅲ)（Ir(piq)₃）为客体材料的薄膜进行了光致发射光谱测试和薄膜在Ir(ppy)₃发光峰516 nm处的光致发光寿命测试,实验发现在Ir(ppy)₃掺杂比例保持定值时,随着深能级掺杂材料Ir(piq)₃的引入,其光致发光光谱中Ir(ppy)₃的相对发光强度减弱且发光寿命变短,当Ir(piq)₃掺杂浓度继续提高时,薄膜光致发光光谱基本保持不变且Ir(ppy)₃的发光寿命基本不变。实验说明在低浓度掺杂下两者的三线态能级之间存在着能量传递,但当掺杂浓度达到高浓度时,能量传递主要来自于主客体之间的传递,两者作为独立的发光中心发光。然后利用溶液法制备了发光层分别为CBP∶Ir(ppy)₃,CBP∶Ir(ppy)₃∶Ir(piq)₃和CBP∶Ir(ppy)₃∶PTB7的三组器件,器件结构为ITO/PEDOT∶PSS/Poly-TPD/EML/TPBi（15 nm）/Alq₃（25 nm）/LiF（0.6 nm）/Al（80 nm）。在Ir(ppy)₃和Ir(piq)₃共掺杂器件和Ir(ppy)₃单掺杂器件的对比实验中发现,加入一定比例的深能级材料后,器件的电致发光光谱发生改变,Ir(piq)₃的相对发光强度增强,器件发光效率下降且效率滚降现象明显。通过对器件进行J-V测试,发现在Ir(ppy)₃单掺杂器件中陷阱填充电流随着掺杂材料浓度的提高而提高,但在加入等浓度深能级材料Ir(piq)₃后,陷阱填充电流基本保持一致。瞬态电致发光测试表明,随着Ir(ppy)₃掺杂比例的提高,器件内由于陷阱载流子释放而产生的瞬时发光强度降低,这是由于Ir(ppy)₃具有一定的传导电荷作用,会减少器件中的陷阱载流子,这进一步说明了具有较深能级的Ir(piq)₃是限制载流子的主要能级陷阱。同时发现随反向偏压的增大,瞬态发光强度增大且发光衰减加速,这是因为位于深能级陷阱的载流子在高电压下被释放,重新复合发光,说明深能级陷阱的确限制住了大量载流子,而由于主体三线态激子具有较长的寿命,激子间相互作用产生的单线态激子在高反压下解离,从而引起三线态激子-极化子相互作用的加剧,导致发光衰减加速。在窄带隙聚合物材料PTB7与Ir(ppy)₃共掺杂器件实验中发现,随着PTB7掺杂浓度提高,陷阱浓度变大且器件效率降低,具有较深能级的PTB7成为了限制载流子的深能级陷阱。因此说明在双掺杂有机磷光电致发光器件中,深能级材料会成为限制载流子的能级陷阱,引起载流子大量堆积,从而导致三线态激子与极化子相互作用加剧,使器件的发光效率衰退。     

掺磷光材料有机电致发光器件的能量传递

将高量子效率的磷光材料fac-tris-2-phenylpyridine iridium(III) (Ir(ppy)3)按不同的比例掺杂到具有载流子传输能力的主体材料poly(N-vinylcarbazole) (PVK)中作为发光层制备磷光电致发光器件。通过对器件发光机制的研究,发现光致发光过程中起主导作用的是Fo¨ster能量转移机制;而在电致发光过程中,器件的发光性能受Dexter能量转移和电荷陷获2种能量传递形式的影响。器件的I-V-L特性表明：Ir(ppy)3的掺杂比例为5%时,器件的光功率效率最大,能量转移最充分。     

PBD的掺杂对PVK:Ir(ppy)3体系发光特性的影响

从三线态激子的发光机理入手,研究了PBD作为电子传输材料对PVK:Ir(ppy)3体系的影响。实验中制备了单层器件ITO/PVK:Ir(ppy)3/PBD/Al,ITO/PVK:Ir(ppy)3:PBD/Al和双层器件,ITO/PVK:Ir(ppy)3:PBD/BCP/Al,其中PVK:Ir(ppy)3的掺杂浓度比例不变,通过改变PBD的掺杂浓度,其变化范围是PBD与PVK的质量比从0:100到20:100,制得了一系列器件,研究了它们的光致发光(PL)光谱和电致发光(EL)光谱。发现PBD这种电子传输材料的加入对器件的亮度有很大提高,当PBD与PVK质量比为10%时,器件亮度最大。     

两种磷光材料在聚合物掺杂体系中的发光特性研究

磷光材料由于可以利用电致激发所形成的单重态和三重态激子,因而可以得到接近100%的内量子效率。文章对常温下基于磷光材料Ir(ppy)₃及Ir(piq)₃掺杂PVK薄膜为发光层的器件的光学和电学特性进行了研究。光致发光的结果显示相同掺杂质量比下由PVK到Ir(piq)₃的能量传递比到Ir(ppy)₃更加困难。通过研究两种掺杂体系不同质量比的电致发光特性,可以认为这两种磷光器件的发光主要来自于磷光客体分子直接俘获载流子发光而非主体的能量传递。Ir(piq)₃掺杂体系对掺杂比例的依赖更为明显,从能级结构分析,认为是由于Ir(piq)₃的更低的HOMO及高的LUMO能级,而比Ir(ppy)₃具有更好的载流子俘获和传输特性。     

磷光铱配合物的纯度对其电致发光性能的影响

采用不同的真空热梯度升华条件,获得了不同纯度的乙酰丙酮酸二(2-苯基吡啶)铱Ir(ppy)₂(acac)。以不同纯度Ir(ppy)₂(acac)为客体材料,制备了结构为ITO:MoO₃/CBP/CBP:Ir(ppy)₂(acac)/TPBi/LiF:Al的有机发光二极管(OLEDs),其中CBP和TPBi分别是4,4'-二(9-咔唑)联苯和1,3,5-三(1-苯基-1H-苯并咪唑-2-基)苯。评价了不同纯度磷光铱配合物制备的器件的电致发光性能,探索了磷光铱配合物纯度对器件性能的影响。结果表明:Ir(ppy)₂(acac)升华后可以提高器件的稳定性,纯度高的材料可以在较低的掺杂浓度下获得较高的发光效率。     

基于CBP:BCzVB:Btp2Ir(acac)体系的白色有机电致发光器件色度飘移研究

以苯乙烯类化合物BCzVB为蓝色荧光染料,以铱配合物Btp_2Ir(acac)为红色磷光染料,共掺杂到CBP基质中作为发光层,制备了白色有机电致发光器件,研究了该体系发光色度漂移的原因。器件在掺杂CBP:6?zVB: 0．2%Btp_2Ir(acac),在．驱动电流从4～200 mA/cm~2变化范围内,发光色坐标从(0．340,0．273)飘移到(0．308, 0．273),色坐标轻微蓝移。对器件发光光谱和亮度-电流密度曲线等分析表明:器件色度的轻微蓝移是由于CBP基质向Btp_2Ir(acac)掺杂剂完全的能量传递、荧光染料BCzVB向磷光染料Btp_2Ir(acac)不完全的能量传递等内在物理过程和磷光染料Btp_2Ir(acac)自身发光饱和等特性共同决定的。     

Ir（PPY）3对Rubrene荧光材料的敏化性研究

最近几年,磷光器件是有机电致发光研究领域和产业化的一大热点。在实验中作者发现PVK∶PBD∶Rubrene共掺体系的发光中存在较强的PVK发光,能量传递不充分。由于一些具有重金属离子的有机物,存在强的自旋-轨道耦合作用,引入到共掺体系可以充分利用单线态和三线态的发光,从而获得高于一般有机材料器件所达到的内量子效率。为获得单色性较好的Rubrene发光,作者将磷光敏化剂Ir(ppy)3引入到PVK∶PBD∶Rubrene共掺溶液中,得到了纯正Rubrene发光,Forester能量传递也更加充分。当进一步提高Rubrene掺杂浓度以后,单色性Rubrene发光更加明显,并讨论了Ir(ppy)3所起的作用和器件的发光机理。磷光材料与有机小分子材料共掺的方法,可以有效提高器件的发光亮度及效率。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.