道威棱镜的偏振特性及偏振补偿研究

为了避免机载光电吊舱中共口径光学系统内部由于道威棱镜旋转引起的激光照射脉冲偏振态的变化,利用琼斯矩阵对道威棱镜的偏振特性与四分之一波片、半波片补偿道威棱镜旋转引起的激光脉冲偏振态变化进行了理论分析和实验验证。结果表明:线偏振的激光脉冲通过旋转一定角度的道威棱镜时,激光脉冲偏振态变为椭圆偏振,偏振态发生变化;而激光脉冲首先通过旋转一定角度的四分之一波片与半波片时,可使通过道威棱镜系统的激光脉冲偏振态保持不变,且两波片旋转角度与道威棱镜旋转角度之间存在一种非线性关系。采用偏振补偿方法可有效避免机载共口径光学系统中道威棱镜引起的激光脉冲偏振态变化,提高激光脉冲能量利用率,降低激光脉冲后向散射抑制难度。     

飞秒激光高精细加工柴油机喷油嘴倒锥孔法

利用飞秒激光加工热效应小、高精细、对材料无选择性等特点,针对柴油发动机高压共轨系统中关键零件——喷油嘴偶件喷油孔的加工需求,设计了一种利用三光楔扫描的飞秒激光加工装置,并进行了喷油嘴倒锥孔加工工艺研究.采用微孔三座标测量机(测量准确度1.2μm)对倒锥孔尺寸准确度进行检测,通过喷油嘴高压液体流量试验台(测量准确度±0.1%)对批量制孔后的油嘴进行了流量测试,结果表明:所设计装置加工的油嘴性能可以满足欧V排放法规的应用要求,对提升汽车制造业水平及柴油车排放标准具有重要意义.     

基于虚拟样机的光纤旋转连接器损耗研究

提出一种基于虚拟样机的光纤旋转连接器损耗的分析方法.建立了道威棱镜系统中的光线输入-输出方程,采用光线追迹和解析模型的混合架构建立了齐次坐标系下的光线分析模型.模型中的输入误差包括输入、输出准直透镜和道威棱镜的角度和位移误差、轴承游隙和齿轮准确度;对30 000个角度准确度±100″、位移准确度±0.01mm的随机误差样本的损耗特性进行计算,结果表明:若要使公差引起的最大损耗小于4dB、损耗分布P(X3dB)小于0.5%,则光纤旋转连接器中准直透镜和道威棱镜角度误差必须控制在±1′以内.     

五角棱镜光学平行差的理论分析

利用矩阵光学方法,计算得出五角棱镜两种光学平行差的解析表达式,分析五角棱镜光学平行差与工作面法向矢量夹角的矩阵关系.基于Agilent激光干涉仪角度测量系统和DHC三维转台搭建实验装置,测量了Thorlabs五角棱镜的两种光学平行差.实验和解析式计算结果偏离度不超过4%.五角棱镜滚动角、偏摆角的变化等效于五角棱镜光学平行差的变化.通过坐标系变换,五角棱镜的自身误差和系统在线测量误差可以被同时标定.该研究对五角棱镜的实际加工、测量系统标定,以及高准确度面形检测提供了参考.     

基于多光子脉冲内干涉相位扫描法对飞秒激光脉冲进行相位测量和补偿的研究

研制了一套基于多光子脉冲内干涉相位扫描方法的可以同时对飞秒激光脉冲进行相位测量和补偿的实验系统装置.实验中,通过自主研发的LabVIEW程序控制液晶空间光调制器和光纤光谱仪,对待测飞秒激光脉冲施加相位扫描,并同时记录受到调制的飞秒激光脉冲的倍频光谱,得到了多光子脉冲内干涉相位扫描(MIIPS)轨迹图.通过MIIPS轨迹图的三次测量和迭代运算,还原出了经过预先啁啾调制的中心波长约为810 nm、重复频率为1 kHz的飞秒激光脉冲的光谱相位,测量精度在0.1 rad以内.根据测量结果,利用液晶空间光调制器对该飞秒激光脉冲进行相位补偿,得到了近似傅里叶变换极限的飞秒激光脉冲.这一装置将在多光子显微成像、脉冲整形、飞秒激光光谱学等众多领域发挥重要作用.     

6H-SiC的飞秒激光超衍射加工

利用飞秒激光直写微纳加工平台, 对6H-SiC材料进行了突破衍射极限的微纳结构加工研究. 使用中心波长和脉宽分别为800 nm和130 fs的钛蓝宝石激光器和荧光倒置显微镜搭建了飞秒激光直写微纳加工平台, 研究了在不同的实验条件下对6H-SiC的光学加工情况, 采用扫描电子显微镜对加工结构进行表征. 通过分析不同的激光功率和不同的曝光时间等实验条件下加工的分辨率, 发现分辨率随着激光功率的减小而提高, 随扫描速度的增大而提高, 且能突破光学衍射极限. 最终获得125 nm的加工线宽, 并加工了加工线宽240 nm, 周期1.0 μm的线阵列. 研究结果为微机电系统(MEMS)的微器件设计开创了新的思路, 对发展MEMS器件具有重要意义. 关键词： 飞秒激光直写 超衍射加工 6H-SiC 微机电系统     

声光偏转器扫描飞秒激光的时间色散补偿

研究了声光偏转器(AOD)扫描飞秒激光的时间色散效应及补偿方案.在800nm波长处，单个AOD引入的群延时色散(GDD)可达～9300fs².在深入分析AOD和棱镜角色散原理的基础上，提出了用色散棱镜预补偿AOD对飞秒脉冲的时间色散，并进行了实验证实.在AOD中心频率处(70MHz)，将398fs的脉冲压缩到122fs，且整个带宽范围内(50MHz—90MHz)脉宽变化范围为120fs—180fs.这表明该方案用于AOD扫描飞秒激光时进行时间色散补偿是非常有效的. 关键词： 飞秒激光 声光偏转器 时间色散 脉冲压缩     

飞秒激光加工蓝宝石超衍射纳米结构

蓝宝石具有超强硬度及耐腐蚀、耐高温、在紫外-红外波段具有良好的透光性等优点,在军工业以及医疗器械方面具有广泛的应用前景.然而这些优点又对蓝宝石的机械加工或化学腐蚀加工带来困难.飞秒激光脉冲具有热损伤小、加工分辨率高、材料选择广等特点,被广泛应用于固体材料改性和高精度三维微纳器件加工.本文提出了利用飞秒激光多光子吸收特性在蓝宝石表面实现超越光学衍射极限的精细加工.利用聚焦后的波长为343 nm的飞秒激光,配合高精密三维压电位移台,实现激光焦点和蓝宝石晶体的相对三维移动,在蓝宝石晶体衬底上进行精确扫描,得到了线宽约61 nm的纳米线,纳米线间的最小间距达到142 nm左右.利用等离子体模型解释了加工得到的纳米条纹的产生原因,研究了激光功率、扫描速度对加工分辨率的影响.最终本工作实现了超越光学衍射极限的加工精度,为实现利用飞秒激光对高硬度材料的微纳结构制备提供了参考.     

飞秒激光全息加工光学系统搭建与分析

合理的光学系统设计及参数优化是飞秒激光全息并行加工系统功能实现的前提。在分析了飞秒激光全息并行加工系统光路设计要求的基础上,对其中的两个关键点进行了较为深入的研究。采用能量利用率高的斜入射方式照射选用的空间光调制器,得出了后续光路设计的关键参数;通过光学理论推导出空间光调制器与两个透镜组成的4-f系统中最佳光路参数,利用Zemax软件对光路中系统孔径仿真,验证了该方案的合理性;搭建了一套合理高效的飞秒激光全息并行加工系统,实现了7焦点阵列的微透镜和微齿轮并行加工。研究结果表明,该光路设计方案可以实现高效的飞秒激光全息加工过程。     

新型的扫描稳像棱镜

本论文发展了双道威屋脊棱镜、四道威层脊棱镜和多道威屋脊棱镜等新型的棱镜组,以满足较大扫描角和较小外形尺寸的需要。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.