退火对ZnS/PS复合体系光致发光特性的影响

用脉冲激光沉积(PLD)技术以多孔硅(PS)为衬底生长了ZnS薄膜,分别测量了ZnS、PS以及ZnS/PS复合体系在室温下的光致发光(PL)光谱。结果发现,ZnS/PS复合体系的PL光谱中PS的发光峰位相对于新制备的PS有所蓝移。把该ZnS/PS样品分成三块,在真空400℃分别退火10,20,30 min,研究不同退火时间对ZnS/PS复合体系光致发光特性的影响。发现退火后样品的PL光谱中都出现了一个新的绿色发光带,归结为ZnS的缺陷中心发光。随着退火时间的延长,PS的发光强度逐渐降低且峰位红移。把ZnS的蓝、绿光与PS的红光相叠加,整个ZnS/PS复合体系在可见光区450~700 nm形成一个较宽的光致发光谱带,呈现较强的白光发射。     

共轭聚合物MEH-PPV的固态阴极射线发光

在有机／无机异质结ZnS／MEH－PPV／ZnS器件中，交流驱动条件下，实现了共轭聚合物MEH－PPV的固态阴极射线发光，器件的发光光谱与MEH－PPV的光致发光谱相同。电子经过ZnS层加速后，成为过热电子，这些过热电子直接碰撞激发MEH－PPV而发光。在日光灯照明下，可以看到器件的均匀发光。     

多孔氧化铝模板制备ZnS纳米线阵列及其光致发光谱

利用阳极氧化铝（AAO）模板,采用电化学沉积方法制备出了ZnS纳米线阵列。扫描电子显微镜（SEM）结果显示,AAO模板孔洞分布均匀,孔径基本一致（约50nm）,孔口呈六边形。TEM结果显示硫化锌纳米线的直径约50nm（与AAM模板孔径一致）,长度约为20μm（与AAM模板厚度一致）。电子衍射结果表明ZnS纳米线为多晶结构。比较了AAO模板组装ZnS纳米线阵列前后的光致发光谱,所得光谱显示,组装了ZnS纳米线阵列的模板的光致发光谱比没有组装的空模板相比多出两个发射峰,分别位于409,430nm,且其发光强度随激发波长的增长而增强。解谱分析表明,这即为ZnS纳米线阵列的发光光谱的两个发射峰,是由导带与受主能级间的跃迁发光和施主与受主能级间的复合跃迁发光共同作用所致。发现由于纳米线尺寸的单一性,发射峰窄化明显,半峰全宽较小,这种现象在其他文献中未曾报道过。     

新有机材料的电致发光的研究

采用新合成的有机材料－硅烷衍生物作为发光物质制备了发蓝、绿光的薄膜电致发光器件。其结构为glass/ITO/PVK SiH/Alq/Mg:Ag。分别测量了SCS－SiH,聚乙烯咔唑（PVK）薄膜的光致发光光谱以及器件的电致发光光谱。其中SCS－SiH薄膜的光致发光谱峰位置在496nm,有机器件的电致发光光谱的峰值为500nm。随着驱动电压的增加发光谱峰蓝移,其变化范围为25nm。在电流密度为89mA/cm^2下器件的发光亮度可达810cd/m^2。     

SiC衬底上外延GaN:Mg材料特性研究

利用扫描电子显微镜、拉曼散射光谱和光致发光谱对在SiC衬底上采用MOCVD异质外延的GaN:Mg薄膜特性进行研究发现：除了一部分Mg原子替代Ga原子呈现受主性外，大部分Mg原子以间隙原子状态（Mg_i）存在，并且在缺陷或者位错处大量聚集引起薄膜张力应力减小，薄膜在降温过程中由于应力不均匀会在部分区域内出现大量的裂纹；Mg的掺杂会加剧GaN无序化程度，致使薄膜质量变差；而室温下的PL谱测量表明蓝带发光由DAP（深施主—浅受主）复合引起，其中D为Mg_GaV_{N 关键词： GaN∶Mg 异质外延 扫描电子显微镜 拉曼散射 光致发光谱}     

ZnCuInS/ZnS量子点与Poly-TPD补偿发光光谱的研究

ZnCuInS/ZnS量子点是一种无重金属、“绿色”半导体纳米材料。在研究中,制备出尺寸为3.2 nm的ZnCuInS/ZnS核壳量子点,并说明它是施主-受主对复合发光。通过测量ZnCuInS/ZnS量子点的光致发光光谱,其发射峰值波长为620 nm、半宽度是95 nm的红光。同时,还制备出Poly-TPD有机薄膜,其发光光谱是峰值波长为480 nm的蓝光。所以,ZnCuInS/ZnS量子点和Poly-TPD发光颜色具有互补性。在ZnCuInS/ZnS量子点薄膜层上包覆一层poly-TPD薄膜后,二者发光颜色互补。在恰当的偏置电压下,可以得到较好的白光光谱。计算表明,其色坐标是(0.336,0.339),颜色指数是92。     

非晶氧化硅薄膜带尾发光特性

采用等离子体增强化学气相沉积技术,通过改变CO2流量制备了不同氧含量的非晶氧化硅薄膜。利用紫外可见吸收谱、傅里叶红外吸收谱和稳态/瞬态光致发光谱等技术研究了薄膜的微观结构和光学特性。实验结果表明,随着氧含量的增加,薄膜的带隙增大,光致发光强度增加、峰值朝高能方向移动、光谱半峰全宽展宽。时间分辨光谱显示薄膜发光峰值处的衰减时间随氧含量的增加从6.2ns单调增加到21ns,而同一样品的发光寿命随发射波长能量增加而减小。综合分析光学吸收、发射及发光衰减特性表明,薄膜的发光机制主要归结为非晶材料带尾态之间的辐射复合。     

Cu掺杂氧化锌薄膜的发光特性研究

通过射频反应溅射法在Si（111）衬底上制备了不同Cu掺杂量的ZnO薄膜.室温下测量了样品的光致发光（PL）谱，所有样品的PL谱中均观察到435?nm左右的蓝光发光带，该发光带的强度与Cu掺杂量和溅射功率有关.当溅射功率为150?W，Cu掺杂量为2.5%时，ZnO薄膜的PL谱中出现了较强的蓝光双峰，而溅射功率为100?W，Cu掺杂量为1.5%时，出现了位于437nm（2.84eV）处较强的蓝光峰，后者的取向性较好.还研究了掺杂量和溅射功率对发光特性的影响，并对样品的蓝光发光机制进行了探讨. 关键词： ZnO薄膜 Cu掺杂 光致发光谱 射频反应共溅射     

衬底温度对ZnMgO薄膜结构和光致发光性能的影响

利用超声喷雾热解方法以不同的沉积温度(450～550 ℃)在石英衬底上制备出一系列ZnMgO薄膜。采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)和光致发光谱(PL)表征了样品的晶体结构、表面形貌和光学性能。结果表明衬底温度对薄膜结构性能和光学特性影响显著。所有薄膜都呈六角纤锌矿多晶结构,其中在530 ℃条件下制备的样品C轴择优最明显,晶粒尺寸均匀,表面形貌平整,结晶质量最好。薄膜的光致发光谱显示随着温度的升高深能级跃迁范围逐渐减小,近紫外带边发光峰逐步出现。衬底温度为530 ℃时在374.5 nm处出现了明显的近紫外发光峰,且几乎没有明显的深能级跃迁出现。     

ZnO：Sb薄膜的光致发光及拉曼特性研究

利用射频磁控溅射法（MS．RF）在玻璃基片上制备了不同掺杂浓度的ZnO：Sb薄膜．借助X射线衍射仪（XRD）、透射光谱、光致发光谱（PL）和拉曼散射光谱（Raman）等手段研究了Sb掺杂浓度对ZnO薄膜的微结构、光致发光和拉曼特性的影响．结果表明：所有样品均呈现ZnO六角纤锌矿结构且具有高度C轴择优取向;在Sb掺杂ZnO薄膜的拉曼光谱中观察到位于532cm^-1的振动模式,结合XRD分析认为此峰归因于Sb替代Zn位且与0成键的局域振动模式（LVMSb--O）;光致发光谱测试发现,仅在ZnO：Sb薄膜中观察到位于3．11eV附近的紫光发射峰,结合拉曼光谱分析认为此峰与XbZn-O复合体缺陷相关．     

The effect of PS porosity on the structure,optical and electrical properties of ZnS/PS

ZnS films were deposited on porous silicon (PS) substrates with different porosities by pulsed laser deposition (PLD). The crystalline structure, surface morphology of ZnS films on PS substrates and optical, electrical properties of ZnS/PS composites were studied. The results show that, ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction corresponding to crystalline structure of cubic phase. With the increase of PS porosity, the XRD diffraction peak intensity of ZnS films decreases. Some voids and cracks appear in the films. Compared with as-prepared PS, the PL peak of PS for ZnS/PS has a blueshift. The larger the porosity of PS, the greater the blueshift is. A new green light emission located around 550 nm is observed with increasing PS porosity, which is ascribed to defect-center luminescence of ZnS. The blue, green emission of ZnS combined with the red emission of PS, a broad photoluminescence band (450–750 nm) is formed. ZnS/PS composites exhibited intense white light emission. The I–V characteristics of ZnS/PS heterojunctions showed rectifying behavior. Under forward bias conditions, the current density is large. Under reverse bias conditions, the current density nearly to be zero. The forward current increases with increasing PS porosity. This work lay a foundation for the realization of electroluminescence of ZnS/PS and solid white light emission devices.     

The study of structure and optoelectronic properties of ZnS and ZnO films on porous silicon substrates

ZnS and ZnO films were prepared on porous silicon (PS) substrates with the same porosity by pulsed laser deposition (PLD), and the structural, optical and electrical properties of ZnS and ZnO films on PS were investigated at room temperature by X-ray diffraction (XRD), scanning electron microscope (SEM), optical absorption measurement, photoluminescence (PL) and I–V characteristic studies. The prepared ZnS was obtained in the cubic phase along β-ZnS (1 1 1) orientation which showed a perfect match with the earlier report while ZnO films were obtained in c-axis orientation. There appeared some cracks in the surface of ZnS and ZnO films due to the roughness of PS substrates. Luminescence studies of ZnS/PS and ZnO/PS composites indicated room temperature emission in a broad, intense, visible photoluminescence band, which cover the blue emission to red emission, exhibiting intensively white light emission. Based on the I–V characteristic, ZnS/PS heterojunction exhibited the rectifying junction behavior, while the I–V characteristic of ZnO/PS heterostructure was different from that of the common diode, whose reverse current was not saturated.     

Effect of annealing on structural, optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I--V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diffraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature, the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550~nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I--V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

The effect of annealing on structural,optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I–V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diflraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature,the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550 nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I-V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

Structure and photoluminescence properties of ZnS films grown on porous Si substrates

ZnS films were deposited on porous silicon (PS) substrates with different porosities. With the increase of PS substrate porosity, the XRD diffraction peak intensity decreases and the surface morphology of the ZnS films becomes rougher. Voids appear in the films, due to the increased roughness of PS structure. The photoluminescence (PL) spectra of the samples before and after deposition of ZnS were measured to study the effect of substrate porosity on the luminescence properties of ZnS/PS composites. As-prepared PS substrates emit strong red light. The red PL peak of PS after deposition of ZnS shows an obvious blueshift. As PS substrate porosity increases, the trend of blueshift increases. A green emission at about 550 nm was also observed when the porosity of PS increased, which is ascribed to the defect-center luminescence of ZnS. The effect of annealing time on the structural and luminescence properties of ZnS/PS composites were also studied. With the increase of annealing time, the XRD diffraction peak intensity and the self-activated luminescence intensity of ZnS increase, and, the surface morphology of the ZnS films becomes smooth and compact. However, the red emission intensity of PS decreases, which was associated with a redshift. White light emission was obtained by combining the luminescence of ZnS with the luminescence of PS.     

Optoelectronic characterization of ZnS/PS systems

ZnS thin films are deposited on porous silicon （PS） substrates with different porosities by pulsed laser deposition （PLD）. The photoluminescence （PL） spectra of the samples are measured at room temperature. The results show that the PL intensity of PS after deposition of ZnS increases and is associated with a blue shift. With the increase of PS porosity, a green emission at about 550 nm is observed in the PL spectra of ZnS/PS systems, which may be ascribed to the defect-center luminescence of ZnS films. Junction current- voltage （I-V） characteristics were studied. The rectifying behavior of I-V characteristics indicates the formation of ZnS/PS heterojunctions, and the forward current is seen to increase when the PS porosity is increased.     

Ti缓冲层及退火处理对Si(111)基片上生长的ZnO薄膜结构和发光特性的影响

采用反应磁控溅射法在Si（111）基片上制备了带有Ti缓冲层的高c轴取向ZnO薄膜.通过X射线衍射分析和光致荧光光谱测量,研究了Ti缓冲层厚度和退火处理对ZnO薄膜结晶质量和光致荧光特性的影响.研究结果表明,Ti缓冲层的引入可以有效改善Si基片上ZnO薄膜的发光性能,但缓冲层存在一个最佳的厚度.薄膜应力是影响ZnO薄膜紫外荧光发射性能的重要因素,较小的残余应力对ZnO薄膜的紫外荧光发射是有利的,残余应力的存在可以改变ZnO薄膜紫外荧光发射能量.随着退火温度的增加,薄膜中的张应力增大,导致带隙宽度减小以及激子复合跃迁峰逐渐向低能方向移动. 关键词： ZnO薄膜 缓冲层 退火处理 应力分析     

(Li,Cu)掺杂ZnO薄膜的发光性质

利用溶胶-凝胶(Sol-gel)法在n型si(100)衬底上制备(Li,Cu)掺杂ZnO薄膜,研究了室温下薄膜的结构、形貌和光致发光性能.研究结果表明,随着Li掺杂浓度的增加,可见光发光强度增加,可见光发射可能是源于单电离氧窄位到价带顶以及单电离氧空位到Li替位Zn(Lizn)受主跃迁的双重作用.与此类似,Cu掺杂Zn...     

纳米β-FeSi2/a-Si多层膜室温光致发光分析

采用射频磁控溅射的方法,在Si（100）基片上制备了纳米β-FeSi₂/Si多层结构,利用X射线衍射、透射电子显微镜、光致发光光谱等表征技术,研究了β-FeSi₂/Si多层结构的结构、成分和光致发光特性.研究结果表明：利用磁控溅射法得到的Fe/Si多层膜,室温下能够检测到β-FeSi₂的1.53 μm处光致发光信号;未退火时多层膜是（非晶的FeSi₂+β-FeSi₂颗粒）/非晶Si结构,退火后则是 关键词： 2')" href="#">β-FeSi₂ 磁控溅射 XRD 光致发光光谱