Photoluminescence of chemical solution-derived amorphous ZnO layers prepared by low-temperature process

Growth characteristic and optical properties of the amorphous ZnO thin films prepared on soda-lime–silica glass substrates by chemical solution process at 100 and 200 °C were investigated by using X-ray diffraction analysis, scanning probe microscope, ultraviolet spectrophotometer, and photoluminescence. The films exhibited an amorphous pattern even when finally heat treated at 100–200 °C for 60 min. The photoluminescence spectrum of amorphous ZnO films shows a strong near-band-edge emission, while the visible emission is nearly quenched.     

Optical properties and structural characteristics of ZnO thin films grown on a-plane sapphire substrates by plasma-assisted molecular beam epitaxy

We investigated structural and optical properties of ZnO thin films grown on (112?0) a-plane sapphire substrates using plasma-assisted molecular beam epitaxy. Negligible biaxial stress in ZnO thin films is due to the use of (112?0) a-plane sapphire substrates and slow substrate cooling. The 14 K photoluminescence spectrum shows a blueshift of energy positions compared with ZnO single crystal. A donor with binding energy of 43 meV and an acceptor with binding energy of ～170 meV are identified by well-resolved photoluminescence spectra. A characteristic emission band at 3.320 eV (so-called A-line) is studied. Based on analysis from photoluminescence spectra, the origin of the A-line, it seems, is more likely an (e, A°) transition, in which defect behaves as an acceptor. The room-temperature photoluminescence is dominated by the FX at 3.307 eV, which is an indication of strongly reduced defect density in ZnO thin films.     

The effect of PS porosity on the structure,optical and electrical properties of ZnS/PS

ZnS films were deposited on porous silicon (PS) substrates with different porosities by pulsed laser deposition (PLD). The crystalline structure, surface morphology of ZnS films on PS substrates and optical, electrical properties of ZnS/PS composites were studied. The results show that, ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction corresponding to crystalline structure of cubic phase. With the increase of PS porosity, the XRD diffraction peak intensity of ZnS films decreases. Some voids and cracks appear in the films. Compared with as-prepared PS, the PL peak of PS for ZnS/PS has a blueshift. The larger the porosity of PS, the greater the blueshift is. A new green light emission located around 550 nm is observed with increasing PS porosity, which is ascribed to defect-center luminescence of ZnS. The blue, green emission of ZnS combined with the red emission of PS, a broad photoluminescence band (450–750 nm) is formed. ZnS/PS composites exhibited intense white light emission. The I–V characteristics of ZnS/PS heterojunctions showed rectifying behavior. Under forward bias conditions, the current density is large. Under reverse bias conditions, the current density nearly to be zero. The forward current increases with increasing PS porosity. This work lay a foundation for the realization of electroluminescence of ZnS/PS and solid white light emission devices.     

The effect of annealing on structural,optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I–V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diflraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature,the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550 nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I-V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

Studies on structural and magnetic properties of Co-doped pyramidal ZnO nanorods synthesized by solution growth technique

Large-area arrays of highly oriented Co-doped ZnO nanorods with pyramidal hexagonal structure are grown on silica substrates by wet chemical decomposition of zinc–amino complex in an aqueous medium. In case of undoped ZnO with an equi-molar ratio of Zn²⁺/hexamethylenetetramine (HMT), highly crystalline nanorods were obtained, whereas for Co-doped ZnO, good quality nanorods were formed at a higher Zn²⁺/HMT molar ratio of 4:1. Scanning electron microscope (SEM) studies show the growth of hexagonal-shaped nanorods in a direction nearly perpendicular to the substrate surface with a tip size of ～50 nm and aspect ratio around 10. The XRD studies show the formation of hexagonal phase pure ZnO with c-axis preferred orientation. The doping of Co ions in ZnO nanorods was confirmed by observation of absorption bands at 658, 617 and 566 nm in the UV–vis spectra of the samples. The optical studies also suggest Co ions to be present both in +2 and +3 oxidation states. From the photoluminescence studies, a defect-related emission is observed in an undoped sample of ZnO at 567 nm. This emission is significantly quenched in Co-doped ZnO samples. Further, the Co-doped nanorods have been found to show ferromagnetic behavior at room temperature from vibrating sample magnetometer (VSM) studies.     

ZnS／PS异质结的光学和电学性质

用脉冲激光沉积（PLD）的方法在多孔硅衬底上沉积了ZnS薄膜,并在室温下研究了ZnS／PS异质结的结构、光学和电学性质。X射线衍射仪（XRD）测量结果表明．制备的ZnS薄膜在28．5°附近有一较强的衍射峰,对应于β-ZnS（111）晶向,说明薄膜沿该方向高度择优取向生长。ZnS／PS复合体系的光致发光谱表明,ZnS的发光与PS的发光叠加在一起,在可见光区形成一个450-700nm较宽的光致发光谱带。呈现较强的白光发射。对ZnS／PS异质结I-V,特性曲线的测量结果表明,异质结呈现出与普通二极管相似的整流特性。在正向偏置下,电流密度较大．电压降较低;在反向偏置下,电流密度接近于零。异质结的理想因子的值为77。     

Photoluminescence studies of ZnO thin films on R-plane sapphire substrates grown by sol–gel method

Zinc oxide (ZnO) thin films on R-plane sapphire substrates were grown by the sol–gel spin-coating method. The optical properties of the ZnO thin films were investigated using photoluminescence. In the UV range, the asymmetric near-band-edge emission was observed at 300 K, which consisted of two emissions at 3.338 and 3.279 eV. Eight peaks at 3.418, 3.402, 3.360, 3.288, 3.216, 3.145, 3.074, and 3.004 eV, which respectively correspond to the free exciton (FX), bound exciton, transverse optical (TO) phonon replica of FX recombination, and first-order longitudinal optical phonon replica of FX and the TO (1LO+TO), 2LO+TO, 3LO+TO, 4LO+TO, and 5LO+TO, were obtained at 12 K. From the temperature-dependent PL, it was found that the emission peaks at 3.338 and 3.279 eV corresponded to the FX and TO, respectively. The activation energy of the FX and TO emission peaks was found to be about 39.3 and 28.9 meV, respectively. The values of the fitting parameters of Varshni's empirical equation were α=4×10^?3 eV/K and β=4.9×10³ K, and the S factor of the ZnO thin films was 0.658. With increasing temperature, the exciton radiative lifetime of the FX and TO emissions increased. The temperature-dependent variation of the exciton radiative lifetime for the TO emission was slightly higher than that for the FX emission.     

Ti-incorporated ZnO films synthesized via magnetron sputtering and its optical properties

Undoped and Ti-doped ZnO films were deposited using radio frequency reactive magnetron sputtering at various sputtering powers. The crystal structures, surface morphology, chemical state and optical properties in Ti-doped ZnO films were systematically investigated via X-ray diffraction (XRD), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and ultraviolet visible (UV–Vis) spectrophotometer. Results indicated that titanium atoms may replace zinc atomic sites substitutionally or incorporate interstitially in the hexagonal lattices, and a moderate quantity of Ti atoms exist in the form of sharing the oxygen with Zn atoms and hence improve the (0 0 2) orientation. The photoluminescence (PL) spectra of the Ti-doped ZnO films contain one main blue peak, whose intensity increased with the increase of sputtering power. Our results indicated that a higher compressive stress in Ti-doped ZnO films results in a lower optical band gap and a lower transmittance, and various Ti impurities can affect the concentration of the interstitial Zn and O vacancies.     

Structural and optical properties of Mn-doped ZnO nanocrystalline thin films with the different dopant concentrations

The transparent nanocrystalline thin films of undoped zinc oxide and Mn-doped (Zn_1−xMn_xO) have been deposited on glass substrates via the sol–gel technique using zinc acetate dehydrate and manganese chloride as precursor. The as-deposited films with the different manganese compositions in the range of 2.5–20 at% were pre-heated at 100 °C for 1 h and 200 °C for 2 h, respectively, and then crystallized in air at 560 °C for 2 h. The structural properties and morphologies of the undoped and doped ZnO thin films have been investigated. X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) were used to examine the morphology and microstructure of the thin films. Optical properties of the thin films were determined by photoluminescence (PL) and UV/Vis spectroscopy. The analyzed results indicates that the obtained films are of good crystal quality and have smooth surfaces, which have a pure hexagonal wurtzite ZnO structure without any Mn related phases. Room temperature photoluminescence is observed for the ZnO and Mn-doped ZnO thin films.     

Excellent UV absorption in spin-coated thin films of oleic acid modified zinc oxide nanorods embedded in Polyvinyl alcohol

The aim of the study is to investigate the optical properties of spin-coated, highly transparent nanocomposite films of oleic acid modified ZnO (Zinc oxide) nanorods embedded in Polyvinyl alcohol (PVA) matrix. Pristine and oleic acid (OA) modified ZnO nanorods have been prepared by wet chemical synthesis and are characterized by X-ray diffraction, FESEM, TEM and FT–IR spectroscopy techniques. The optical properties of ZnO/PVA films are studied using UV–visible absorption and Photoluminescence (PL) spectroscopy. The results show that the optical absorption of the films in the UV region is quite high and more than 95% absorption is observed in films prepared from OA modified ZnO nanorods. The excellent UV absorption at around 300 nm offers prospects of applications of these films as efficient UV filters in this wavelength region. The PL spectrum of pristine ZnO nanorods shows almost white light emission whereas OA modified ZnO nanorods have a more intense peak centered in the blue region. The PL emission of OA modified ZnO/PVA film shows appreciable increase in intensity compared to the film obtained with pristine ZnO. The surface modification of ZnO by the polymer matrix removes defect states within ZnO and facilitates sharp near band edge PL emission at 364 nm.     

Room temperature photoluminescence property of Mo-doped In2O3 thin films

Mo-doped In₂O₃ thin films have been prepared on glass substrates using an activated reactive evaporation method and systematically studied the effect of oxygen partial pressure on the structural, optical, electrical and photoluminescence properties of the films. The obtained films are highly transparent and conductive. The films exhibited the lowest electrical resistivity of 5.2 × 10⁻⁴ Ω cm, with an average optical transmittance of 90% in the visible region. An intensive photoluminescence emission peaks were observed at 415 and 440 nm.     

High c-axis preferred orientation ZnO thin films prepared by oxidation of metallic zinc

Thin films of zinc oxide were grown on glass substrates by thermal oxidation. The metallic zinc films were thermally oxidized at different temperatures ranging from 300 to 600 °C to yield ZnO thin films. The structural property of the thin films was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The X-ray diffraction measurements showed that the films oxidized at 300 °C were not oxidized entirely, and the films deposited at 600 °C had better crystalline quality than the rest. When the oxidation temperature increased above 400 °C, the films exhibited preferred orientation along (002) and high transmittance ranging from 85% to 98% in vis–near-infrared band. Meanwhile, the films showed a UV emission at about 377 nm and green emission. With the increasing of oxidation temperature, the intensity of green emission peak was enhanced, and then decreased, disappearing at 600 °C, and the case of UV emission increased. Furthermore, a strong green emission was observed in the film sintered in pure oxygen atmosphere.     

Effect of GZO thickness and annealing temperature on the structural,electrical and optical properties of GZO/Ag/GZO sandwich films

The GZO/Ag/GZO sandwich films were deposited on glass substrates by RF magnetron sputtering of Ga-doped ZnO (GZO) and ion-beam sputtering of Ag at room temperature. The effect of GZO thickness and annealing temperature on the structural, electrical and optical properties of these sandwich films was investigated. The microstructures of the films were studied by X-ray diffraction (XRD). X-ray diffraction measurements indicate that the GZO layers in the sandwich films are polycrystalline with the ZnO hexagonal structure and have a preferred orientation with the c-axis perpendicular to the substrates. For the sandwich film with upper and under GZO thickness of 40 and 30 nm, respectively, it owns the maximum figure of merit of 5.3 × 10⁻² Ω⁻¹ with a resistivity of 5.6 × 10⁻⁵ Ω cm and an average transmittance of 90.7%. The electrical property of the sandwich films is improved by post annealing in vacuum. Comparing with the as-deposited sandwich film, the film annealed in vacuum has a remarkable 42.8% decrease in resistivity. The sandwich film annealed at the temperature of 350 °C in vacuum shows a sheet resistance of 5 Ω/sq and a transmittance of 92.7%, and the figure of merit achieved is 9.3 × 10⁻² Ω⁻¹.     

Effect of annealing on structural, optical and electrical properties of ZnS/porous silicon composites

ZnS films were prepared by pulsed laser deposition (PLD) on porous silicon (PS) substrates. This paper investigates the effect of annealing temperature on the structural, morphological, optical and electrical properties of ZnS/PS composites by x-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) and I--V characteristics. It is found that the ZnS films deposited on PS substrates were grown in preferred orientation along β-ZnS (111) direction, and the intensity of diffraction peak increases with increasing annealing temperature, which is attributed to the grain growth and the enhancement of crystallinity of ZnS films. The smooth and uniform surface of the as-prepared ZnS/PS composite becomes rougher through annealing treatment, which is related to grain growth at the higher annealing temperature. With the increase of annealing temperature, the intensity of self-activated luminescence of ZnS increases, while the luminescence intensity of PS decreases, and a new green emission located around 550~nm appeared in the PL spectra of ZnS/PS composites which is ascribed to the defect-center luminescence of ZnS. The I--V characteristics of ZnS/PS heterojunctions exhibited rectifying behavior, and the forward current increases with increasing annealing temperature.     

Design and fabrication of nanometric ZnS/Ag/MoO3 transparent conductive electrode and investigating the effect of annealing process on its characteristics

In this paper, a ZnS/Ag/MoO₃ (ZAM) nano-multilayer structure is designed theoretically and optimum thicknesses of each layer are calculated. ZnS/Ag/MoO₃ multilayer films with optimized thicknesses have also been fabricated on glass substrates by thermal evaporation method at room temperature. The structural, electrical and optical properties of ZnS/Ag/MoO₃ multilayer are investigated with respect to the variation of annealing temperature. X-ray diffraction patterns show that increase in annealing temperature increases the crystallinity of the structures. High-quality multilayer films with the sheet resistance of 4.5 Ω/sq and the maximum optical transmittance of 85% at 100 °C annealing temperature are obtained. The allowed direct band gap for annealing at different temperatures is estimated to be in the range of 3.37–3.79 eV. The performance of the ZAM multilayer films are evaluated using a predefined figure of merit. These multilayer films can be used as transparent conductive electrodes in optoelectronic devices such as solar cells and organic light emitting diodes.     

Influence of argon ambience on the structural,morphological and optical properties of pulsed laser ablated zinc sulfide thin films

Nanostructured zinc suplhide thin films are successfully deposited on quartz substrates using pulsed laser deposition (PLD) under different argon pressures (0, 5, 10, 15 and 20 Pa). The influence of argon ambience on the microstructural, optical and luminescence properties of zinc sulfide (ZnS) thin films is systematically investigated. The GIXRD data suggests rhombohedral structure for ZnS films prepared under different argon ambience. Self-assembly of grains into well-defined patterns along the y direction is observed in the AFM image of the film deposited under argon pressure 20 Pa. All the films show a blue shift in optical band gap. This can be due to the quantum confinement effect and less widening of conduction and valence band for the films with less thickness and smaller grain size. The PL spectra of the different films are recorded at excitation wavelengths 250 nm and 325 nm and the spectra are interpreted. The PL spectra of the films recorded at excitation wavelength 325 nm show intense yellow emission. The film deposited under an argon pressure of 15 Pa shows the highest PL intensity for excitation wavelength 325 nm. For the PL spectra (excitation at 250 nm), the highest PL intensity is observed for the film prepared under argon free ambience. In our study, 15 Pa is the optimum argon pressure for better crystallinity and intense yellow emission when excited at 325 nm.     

Nanostructures and luminescence properties of porous ZnO thin films prepared by sol–gel process

ZnO thin films containing nano-sized pores were synthesized on solid substrates through a sol–gel process by accommodating cetyl-trimethyl-ammonium bromide (CTAB) as an organic template in the precursor solution. By X-ray diffraction the resultant ZnO films were found to possess ordered pore arrays forming lamellar structure with the spacing between two adjacent pores being ∼3.0 nm. Photoluminescence measurements indicated that the surfactants effectively passivated the surface defects of the ZnO films responsible for the green emission. Al doping was found to improve not only the lamellar structure of the pore arrays but also the near-band-gap emission intensity while the suppression effect of CTAB on the green emission remained undisturbed. With a proper control of doping level, the optical property as well as the structural integrity can be tailored to augment the potential of ZnO films for the optoelectronics and sensor applications.     

Luminescence and physical properties of copper doped CdO derived nanostructures

In this paper, we studied the photoluminescence (PL), the morphological, electrical and optical properties of pure and copper-doped cadmium oxide. CdO films were grown by a facile sol–gel spin coating process at 1200 rpm, and doped with copper at 2 and 3%. A (1 1 1)-oriented cubic structure with a lattice parameter of a=4.69 Å was confirmed by X-ray diffraction. Copper was shown to improve the optical transmittance in the short wavelength range of the visible spectrum. The optical band gap of CdO ranged between 2.49 and 2.62 eV as a result of Cu content. At room temperature, resistance fell drastically with Cu doping levels. AFM analysis of samples exhibited nano-mounts and nanowires. Finally, PL results showed a strong blue–violet emission peak at 2.80 eV.     

Comparative study on structural and optical properties of ZnO thin films prepared by PLD using ZnO powder target and ceramic target

Zinc oxide thin films have been obtained in O₂ ambient at a pressure of 1.3 Pa by pulsed laser deposition (PLD) using ZnO powder target and ceramic target. The effect of temperature on structural and optical properties of ZnO thin films was investigated systematically by XRD, SEM, FTIR and PL spectra. The results show that the best structural and optical properties can be achieved for ZnO thin film fabricated at 700 °C using powder target and at 400 °C using ceramic target, respectively. The PL spectrum reveals that the efficiency of UV emission of ZnO thin film fabricated by using powder target is low, and the defect emission of ZnO thin film derived from Zn_i and O_i is high.     

Epitaxial ZnO thin films grown by pulsed electron beam deposition

In this work, the pulsed electron beam deposition method (PED) is evaluated by studying the properties of ZnO thin films grown on c-cut sapphire substrates. The film composition, structure and surface morphology were investigated by means of Rutherford backscattering spectrometry, X-ray diffraction and atomic force microscopy. Optical absorption, resistivity and Hall effect measurements were performed in order to obtain the optical and electronic properties of the ZnO films. By a fine tuning of the deposition conditions, smooth, dense, stoichiometric and textured hexagonal ZnO films were epitaxially grown on (0001) sapphire at 700 °C with a 30° rotation of the ZnO basal plane with respect to the sapphire substrate. The average transmittance of the films reaches 90% in the visible range with an optical band gap of 3.28 eV. Electrical characterization reveals a high density of charge carrier of 3.4 × 10¹⁹ cm^?3 along with a mobility of 11.53 cm²/Vs. The electrical and optical properties are discussed and compared to ZnO thin films prepared by the similar and most well-known pulsed laser deposition method.