粒子束团状态对测量束流发射度及能量的影响

为了验证国产质子注入器的参数是否满足需求,注入器团队设计了束流测量系统用于测量国产质子直线注入器束流的流强、发射度、能量以及能散等关键指标。此测量系统包含了采用变聚焦法测量发散度、采用分析磁铁测量束流能量和能散的主要功能。利用束流输运线设计软件Tracewin(版本2.11.4.1)进行了系统束线的物理设计,对束测系统测量质子束流的发散度和能量的精度进行了模拟计算。由于经过RFQ-(APF)DTL加速后的粒子束团为“拖尾”的非理想粒子束团,需要针对非理想束团对束测系统测量发射度和能量产生的影响进行分析。通过对模拟计算结果的分析,发现相对于测量理想粒子束团的结果非理想粒子束团对束测系统测量发射度精度影响较大;非理想粒子束团对束测系统测量能量精度影响较小。     

高能光源增强器束流横向尺寸测量系统设计

高能同步辐射光源的增强器将直线加速器注入的束流加速到储存环所需的能量,为储存环提供高品质的电子束。为了对增强器的束流横向截面尺寸、发射度及能散进行测量,设计了两条可见光-紫外波段的束测光束线。两条光束线分别选取无色散和色散较大的两处弯铁位置作为光源点,使用两套同步光成像系统来监测光源点的束流截面尺寸,并计算束流发射度及能散。介绍了同步光引出真空室及光学成像系统,对影响成像质量的空间分辨率进行了分析,并针对升能过程中不同能量下束流光斑变化的测量进行了设计。     

直线感应加速器模拟软件多功能发射模块开发

在模拟直线感应加速器电子束输运过程中,为了正确设置注入器电子束参数,以注发射模型为基础,研发了可设置发射度、能散和电子束倾斜的多功能发射模型。理论研究了发射度、能散以及电子束倾斜角度,并将这些理论实现到发射模块上。建模对多功能发射模块进行测试,比较设定的电子束参数与模拟测定的电子束参数。通过比较,观测到设定电子束参数与模拟测定值一致,验证了多功能模块开发的正确性。     

北京大学ERL装置交汇段的研究与设计

 在交汇段设计理论的基础上，针对北京大学ERL的具体情况，对交汇段的束流传输结构进行了优化设计，通过模拟得到了满足要求的一组设计参数；研究了空间电荷效应以及相干同步辐射对束流发射度、能散及包络的影响。结果表明：空间电荷效应对发射度影响不大，但对束流包络影响较明显；相干同步辐射引起的发射度增长及能散较小，且不影响束流包络。     

Analytical and simulation studies for diode and triode ion beam extraction systems

This work is concerned with ion beam dynamics and compares the emittance to aberration ratios of two-and three-electrode extraction systems. The study is conducted with the aid of Version 7 of SIMION 3D ray-tracing software. The beam dependence on various parameters of the extraction systems is studied and the numerical results lead to qualitative conclusions.     

基于单个四条带BPM的非拦截式能散度测量方法

能散度是反映束流品质的重要参数,采用传统测量方法测量时打到靶上的束流不能得到利用,测得的数据也是多个宏脉冲的平均值,利用该方法的测量结果进行束流调节时,要等待荧光靶从束流轨道中反复插入和提出,调节时间很长。基于单个四条带束流位置检测器,结合发射度测量的方法,实现了非拦截式能散度测量方法。该方法能在不加入额外设备的情况下对每个束流宏脉冲的能散度进行测量,测量结果与传统的拦截式测量方法结果相吻合。进行了误差分析,指出为了减小测量系统误差,需要尽可能使束流通过束流位置检测器中心。     

混频＋m腔微波电子枪束流动力学特性

为了使自由电子激光器的电子束注入器具有小的能散，小的横向发射度、高的亮度，本文提出在　腔的微波电子枪中采用混频腔技术，并用解析方法研究了混频加速的　腔方案的动力学特性，所导出的表达式说明此方案能改善束流的纵向和横向粒子动力学性能；为了对比，还借助于ＰＡＲＭＥＬＡ程序对此方案进行了束流动力学模拟，结论与导出的解析表达式结果一致．     

曙光一号自由电子激光自发辐射放大的理论计算

曙光一号自由电子激光装置用自发辐射放大(ASE)机理,在毫米波波段测得了数百毫瓦的光信号输出。利用三维WAGFEL程序,结合曙光一号直线感应加速器型自由电子激光放大器参数,详细地分析了自发辐射放大的增益、输出功率随电子束的质量(包括束流能散度、流强、发射度等因素)的变化情况,给出了相应的定标关系;并且考察了摇摆场随机误差对自发辐射放大功率的影响。最后对自发辐射放大的实验结果进行了分析。     

Emittance Dominated Long Bunches in Dual Harmonic RF Systems

The storage of long bunches for long time intervals needs flattened stationary buckets with large bucket height. In the case of small energy spread with a cooled beam, the Coulomb interaction cannot be ignored. The properties of the dual harmonic RF systems are discussed for the emittance dominated long bunches below transition. The external voltage has to be increased to compensate the Coulomb interaction to keep bunch length unchanged. The longitudinal motion of the initially mismatched beam has been studied for both single and dual harmonic RF system. Bucket height of the single harmonic system is too small even for 20 % mismatch. Halo formation and debunching can be seen after a few synchrotron periods for single particles with large amplitude. The simulation results by using ORBIT code for the FAIR-HESR synchrotron has been given together with theoretical analysis.     

合肥光源新的束团截面及发射度测量系统的研制

介绍了合肥光源储存环紫外光束团截面及束流发射度测量系统. 本系统采用光学探测, 由光学成像和图像采集处理两大部分组成. 光学成像部分利用光学成像将中心波长366.1nm紫外光1:1成像于CCD探测器上. 图像采集处理部分将CCD探测器采集的视频信号由电缆输出到图像采集卡进行图像采集, 然后由LabVIEW程序进行数据处理获得束团截面尺寸以及束流发射度和耦合度, 最后给出了实验结果.     

自由电子激光对束流品质的要求与改善措施

本文叙述了自由电子激光对电子束发射度、能散度和稳定性的要求，并介绍了采用谐波混频腔、光阴极微波电子枪和超导技术等改善措施中的关键技术问题。     

100 MeV电子直线加速器的物理设计

 能量为100 MeV左右的高性能电子直线加速器是第三代同步辐射光源注入器和自由电子激光注入器的重要组成部分,采用热阴极栅控电子枪、聚束系统和4根SLAC型加速管作为加速器主体结构,一套45 MW的速调管调制器系统和波导系统作为微波功率源系统。设计中,使用了国际通用的模拟软件对加速器的动力学特性进行了数值模拟和参数优化,电子束能量达到100 MeV以上,能散小于1%,归一化发射度小于30 mm·mrad。     

三种高密度强流束亮度测量技术

利用已经建成的4 MeV LIA注入器,结合时间分辨测量系统研究了三种测量技术:发射度测量法、无场准直器和磁场准直器测量法。介绍了强流束亮度定义和典型方法理论分析及测量技术的物理概念,提出了用于猝发多脉冲电子束发射度测量装置的设计与调试,通过对时间分辨测量系统的分幅相机记录的光强度分布信息处理,得到电子束束斑均方根半径和发射角,分析某一时刻数据,即可得到电子束某一时刻发射度,从而获得多脉冲电子束时间分辨发射度。在4 MeV LIA注入器上对多脉冲电子束流的发射度进行测量,得到电子束归一化均方根发射度约为114 mmmrad、双脉冲456 mmmrad的归一化发射度。最后结合电子束的高斯分布初步分析并给出均方根发射度、实测发射度和边发射度的关系。     

Positron injection and acceleration on the wake driven by an electron beam in a foil-and-gas plasma

A novel approach for generating and accelerating positron bunches in a plasma wake is proposed and modeled. The system consists of a plasma with an embedded thin foil into which two electron beams are shot. The first beam creates a region for accelerating and focusing positrons and the second beam provides positrons to be accelerated. Monte Carlo and 3D PIC simulations show a large number of positrons (10(7) approximately 10(8)) are trapped and accelerated to approximately 5 GeV over 1 m with relatively narrow energy spread and low emittance.     

强流ECR离子源引出系统研究

为了提高强流ECR 离子源的引出束流品质,分别设计了1# 和2# 引出系统,利用束流引出模拟软件PBGUNS 对1# 和2# 引出系统进行了质子束流引出与传输的模拟计算,结合实际测得的发射度数据分析引出系统,发现2# 引出系统比1# 引出系统引出束流品质高。对ECR 离子源引出系统的电势等位线分布等参数引起的球差进行了简单数学推导及MATLAB 绘图,并结合1# 和2# 引出系统束流相图模拟结果证明了球差会使引出束流品质有效发射度增长,通过适当加大电极孔径可改善束流聚焦情况,得到了束流光学聚焦较好的束流引出系统设计。To improve the quality of extracted ion beam from a high current ECR ion source, 1# and 2# extraction systems were designed and tested. The PBGUNS code was used to simulate the 1# and 2# extraction systems of proton ion beam. The emittance measurement results with the two different extraction systems were compared and analyzed with the simulation, the conclusion that more high quality beam extracted from 2# system than 1# system was got. The formula derivation of ECR ion source extraction system spherical aberration and MATLAB drawing was done by the analyzing on the distribution of extraction field equipotentials, effective emittance increasing caused by spherical berration was proved by 1# and 2# extraction systems beam phase space simulation result, beam focusing would be improved if electrode hole size increasing appropriately and a general concept on good optics focusing of ion beam extraction system was proposed finally.     

Instantaneous electron beam emittance measurement system based on the optical transition radiation principle

One kind of instantaneous electron beam emittance measurement system based on the optical transition radiation principle and double imaging optical method has been set up. It is mainly adopted in the test for the intense electron-beam produced by a linear induction accelerator. The system features two characteristics. The first one concerns the system synchronization signal triggered by the following edge of the main output waveform from a Blumlein switch. The synchronous precision of about 1 ns between the electron beam and the image capture time can be reached in this way so that the electron beam emittance at the desired time point can be obtained. The other advantage of the system is the ability to obtain the beam spot and beam divergence in one measurement so that the calculated result is the true beam emittance at that time, which can explain the electron beam condition. It provides to be a powerful beam diagnostic method for a 2.5 kA, 18.5 MeV, 90 ns (FWHM) electron beam pulse produced by Dragon I. The ability of the instantaneous measurement is about 3 ns and it can measure the beam emittance at any time point during one beam pulse. A series of beam emittances have been obtained for Dragon I. The typical beam spot is 9.0 mm (FWHM) in diameter and the corresponding beam divergence is about 10.5 mrad.     

基于汤姆逊散射的X射线光源的物理问题研究

针对汤姆逊散射X射线光源,推导了任意散射角下出射X射线的时间结构、产额,分析了位置和同步偏差、发射度、能散等非理想因素的影响.     

光速调管FEL的小信号增益理论

 利用自由电子激光（FEL）纵模统一理论，系统地分析了光速调管FEL的小信号增益理论，并对色散参数Nd、束流能散度和发射度的影响进行了讨论。     

狭缝法合肥光源高亮度注入器发射度测量系统

为了测量受空间电荷效应支配的发射度,合肥光源高亮度注入器采用了狭缝法进行测量,研究了基于狭缝法发射度测量系统的构成,并以实例比较了单狭缝和多狭缝在发射度测量系统中的应用。两种测量方法的结果表明:单狭缝法测量的结果更接近于模拟计算值,可有效避免子束团之间的重叠,适用范围更广。实验结果表明:在240 pC电荷量情况下,合肥光源高亮度注入器仍然具有较小的归一化发射度,为（1.840.085） mmmrad。