共查询到19条相似文献,搜索用时 93 毫秒
1.
2.
3.
对于饱和蒸气壁面凝结过程,蒸气分子在体相与过冷壁面间过渡区的微观演化机制尚不清晰,分子团聚模型认为分子到达壁面凝结前首先在体相中形成一定团簇分布,但由于观测近壁边界层微小空间中微观粒子的动态演化较为困难,对该模型的实验验证并不充分.基于团簇内部的氢键网络,利用衰减全反射傅里叶红外光谱技术,实时检测了近壁薄层内蒸气分子凝结过程中的动态行为,直接验证了近壁区的团簇分布,表明团簇是凝结和液滴生长的主要单元,且平均团簇尺寸沿着靠近壁面方向逐渐增大.利用团簇体的氢键特征,又观测了乙醇蒸气的近壁面团聚行为,进一步验证了壁面凝结过程团簇演化的合理性.此外,实验发现乙醇蒸气冷凝的团簇分布空间范围要小于同样条件下的水团簇分布范围,这可能间接表明乙醇蒸气凝结的传热边界层范围小于水蒸气凝结的传热边界层范围,而导致其传热性能较弱.利用壁面结构调节近壁区团簇分布,将为含有不凝气的蒸气冷凝传热或气相水汽捕获等过程的强化提供新方向. 相似文献
4.
5.
本文针对内径D=0.1m、高H=3 m的三维可视快速流化床上升管,建立了图像采集及处理系统,对平均粒径d_s=0.25 mm的石英砂(颗粒密度ρ_p=2650 kg/m~3,堆积密度ρ_(pa)=1590 kg/m~3)在颗粒循环量G_s=40~70 kg/(m~2s),流化风速U_g=4.35 m/s下形成的颗粒团絮进行了研究,提出了一套针对三维快速流化床近壁面颗粒团絮的识别和表征方法并优化了计算参数。结果表明,该方法能够准确识别不同类型("U"形、倒"U"形、条形)的颗粒团絮;颗粒团絮的尺寸随上升管高度增加和固体循环通过减小而增大,颗粒团絮数量随上升管高度增加和固体循环通量减小而减少;随固体循环通量变化,"U"形和倒"U"形的颗粒团絮下落速度的平均值均为1 m/s左右。 相似文献
6.
垂直套管环隙内汽液固三相流动沸腾传热的实验研究 总被引:1,自引:0,他引:1
符号表C。固体颗粒在液q热通量kw/mZu。固体颗粒与液体中的含量voL%,液体汽化游热kJ/kg体的滑移速度m/s小固体颗粒直径mm或mTi流体温度”CP;液体的密度kg/m’D实验段当量直径mm或mTw加热壁面温度“CP。固体颗粒的密度kg/m’h传热膜系数kw/m’K。1循环液速m/sH液相粘度mPa。k液体导热系数W/inK1前言自MatchL.P.等人首次将固体颗粒引入换热器应用于地热利用山后,对这种流化床换热器的研究开始增多【‘-‘]。研究结果均表明,固体颗粒的引入,可显著强化传热,并有较好的防垢抗垢性能。本文的研究是在液体在垂直套管环… 相似文献
7.
本文利用基于复合网格系统的计算方法,对Re=50~1200的近壁插入圆柱流场进行数值模拟,研究过渡流状态下在壁面附近插入圆柱对下游壁面传热强化的影响。并基于低速循环水槽流动实验台,采用粒子成像测试法(PIV)对Re=100~500的近壁插入圆柱流场进行可视化实验研究,验证了数值模拟方法的可靠性。研究结果表明:近壁插入圆柱流场在Re=100时进入过渡流状态;Re直接影响圆柱尾流中周期性涡脱和壁面涡岛的发生位置及其洗刷效应的大小,随着Re的增大,洗刷效应明显增强,因而,过渡流范围内Re越大,圆柱下游壁面传热强化越大。 相似文献
8.
颗粒聚集成团是稠密两相流动中的基本现象.本文直接以颗粒团为研究对象,建立了颗粒团运动的DEM软球模型,具体给出了稠密气固两相流中颗粒团大小的计算表达式,建立了非球形颗粒团运动、接触碰撞及破碎模型,并将此模型用于模拟一循环流化床内稠密气固两相流动,得到了流化床内颗粒团详细的运动碰撞经历及浓度、粒径分布,所得结果合理,与前人实验值相符.另外,计算表明,采用颗粒团运动的DEM软球模,能使计算量有效减少,计算时间明显缩短,说明本模型可有效地用于工程意义上的稠密气固两相流问题的模拟。 相似文献
9.
根据相变过程的微观物理机理和热力学特性,提出了冷凝传热过程中,近壁面蒸汽分子经由团聚阶段进而冷凝成宏观液滴的物理模型.并将团聚体分布与滴状冷凝传热性能相联系,从而研究不凝性气体对滴状冷凝传热过程的影响.在改进的Dillmann和Meier(DM)模型基础上,将分子团聚过程中的临界过饱和度与冷凝过程中的过冷度相联系,以及将团聚体的能量特性与液固界面物理化学特性相联系,将团聚模型与考虑固液界面效应的滴状冷凝传热模型相联系,建立了近壁面条件影响的分子团聚模型.利用模型计算了近壁面蒸汽中团簇体尺寸和分布,以及不凝性气体存在导致的蒸汽冷凝团聚体分布的变化,并结合滴状冷凝传热模型,定量解释了少量不凝性气体的存在,极大影响了冷凝传热性能的现象.模型计算结果与实验结果及文献中含不凝气的蒸汽冷凝传热实验数据进行了比较,两者符合较好,验证了所提出模型的合理性. 相似文献
10.
本文基于颗粒动理学理论建立了流化床中的欧拉双流体模型,采用了单气泡沿壁面运动物理模型,从颗粒分布特性、温度分布特性和瞬时传热特性三个方面对超临界水流化床和气固流化床的床层与壁面间传热特性进行了对比研究。研究表明,相同条件下,相对于气固流化床,超临界水流化床中气泡的直径和上升速度都较小;超临界水流化床中床层与壁面间的传热系数与颗粒浓度呈反相关关系,而对于气固流化床则是正相关关系;并且不同于气固流化床,超临界水流化床床层与壁面间传热系数在颗粒浓度较低处对表观速度变化比较敏感。 相似文献
11.
Convective heat transfer coefficients were measured experimentally for a tube immersed vertically in a circulating fluidized bed. Circulating fluidized beds operate in the dilute transport regime of two-phase (solid/gas) flow. The dominant mechanism for heat transfer to surfaces is particle-induced convection. In this study, experiments were carried out in a circulating fluidized bed of15 cm diameter and 11 m height. An instrumented tube of 9.5 mm diameter and 1.3 m length was placed vertically at the centeriine of the fluidized bed to measure convective heat transfer coefficients at several different elevations in the bed. Three types of particles, with mean diameters ranging from 68 to 2S1 urn, were used in the experiments at superficial gas velocities in the range of 1.3 to 8.2 m/s. Results showed that the convective heat transfer coefficients with solid/gas two-phase circulation were two to three times greater than those for single-phase gas convection at the same velocity. For a given gas velocity, the coefficients increased with increasing solid mass flux, but decreased with elevation. It was demonstrated that the heat transfer coefficients for the immersed tube and for the bed wall could be correlated with different functional dependence on the two-phase suspension density. 相似文献
12.
13.
14.
A mathematical model is proposed to show the evolution of temperature, chemical composition and energy release or transfer in slugs, clouds and particulate phase, in a fluidized bed where there are slugs, of a mixture of air and propane, moving up through the particulate phase previously set in the state of incipient fluidization with air. The analysis begins as the slugs are formed at the orifices of the distributor, until they explode inside the bed or emerge at the free surface. The model also makes the analysis of what happens in the gaseous mixture that leaves the free surface of the fluidized bed until the propane is thoroughly burnt. It is essentially built upon a simple quasi-global mechanism for the combustion reaction and the mass and heat transfer equations from the two-phase model of fluidization. The aim was not to propose a new modelling approach, but to combine classical models, one concerning the reaction kinetics and the other the bed hydrodynamic aspects, to obtain a better insight on the events occurring inside a fluidized bed reactor, enhancing the understanding of this type of reactor. Experimental data to balance with the numerical model were obtained through tests on the combustion of commercial propane, in a laboratory scale fluidized bed, using four sand particle sizes: 400–500, 315–400, 250–315 and 200–250 μ m. The mole fractions of CO2, CO and O2 in the flue gases and the temperature of the fluidized bed were measured and compared with the numerical results. 相似文献
15.
Heat transfer augmentation due to turbulence in the gaseous flow of a gas-solid fluidized bed is analyzed. Since the heat transfer in such beds is enhanced by various mechanisms, each mechanism's contribution can only be separately evaluated using special means. Therefore, we employed a new mass transfer measurement technique to measure the contribution of the turbulence induced by particle motion on the total heat transfer occurring around a horizontal test cylinder immersed in a fluidized bed. Results indicate that the mass transfer, i.e., analogous to convective heat transfer to or from the gaseous flow, is enhanced by the turbulence produced from particle motion on the front side of the cylinder surface, but that other heat transfer mechanisms besides turbulence contribute to the heat transfer augmentation taking place on the cylinder side walls and back-side surface. 相似文献
16.
17.
18.