Feasibility of bone assessment with leaky Lamb waves in bone phantoms and a bovine tibia

In this study, the effect of cortical thickness variation on the propagation of leaky Lamb waves is investigated by using an axial transmission technique commonly used to characterize long bones. Three Lucite plates with thicknesses of 1, 3, and 5 mm as bone phantoms and one bovine tibia with a cortical thickness of 2 mm were used at various low frequencies. Experimental measurements in bone phantoms show that the peak frequency and amplitude of excited Lamb modes strongly depend on the thickness of the Lucite plate. In the bovine tibia, the S0 and A0 Lamb modes are consistently observed in the frequency-thickness region from 0.2 to 1.0 MHz mm, and can be effectively launched at a frequency of 200 kHz, suggesting 200 kHz to be the optimal signal frequency for in vivo clinical applications. It can be also seen that both modes are affected by the frequency-thickness product, but the effect is greater for the A0 mode. Hence, the A0 Lamb mode seems more sensitive to cortical thickness change due to aging and osteoporosis. This study suggests that the use of leaky Lamb waves is feasible for ultrasonic bone assessment.     

采用单个压电传感器的单模式兰姆波激发频率的选择

考虑了压电传感器(PZT)与板之间的耦合作用,从理论上研究了单个压电传感器激发时产生单模式兰姆波的频率调节方法,实验给出了模式选择在兰姆波结构健康监测中的应用. 在板材、板厚以及PZT尺寸一定的情况下,从理论上能够预测到作为频率函数的各兰姆波模式的幅值变化. 根据某特定兰姆波模式的幅值最大而其他模式幅值相对最小时所对应的频率,即可识别出该兰姆波模式优化的激发频率. 数值仿真验证了理论的有效性以及单模式兰姆波选择的可能性. 在不同的激发频率下,分别激发了优化的A0 模式,优化的S0模式以及共存的A0和S0模 关键词： 兰姆波 压电传感器 激发频率 结构健康监测     

Piezoelectric transducer parameter selection for exciting a single mode from multiple modes of Lamb waves

Excitation and propagation of Lamb waves by using rectangular and circular piezoelectric transducers surface-bonded to an isotropic plate are investigated in this work. Analytical stain wave solutions are derived for the two transducer shapes, giving the responses of these transducers in Lamb wave fields. The analytical study is supported by a numerical simulation using the finite element method. Symmetric and antisymmetric components in the wave propagation responses are inspected in detail with respect to test parameters such as the transducer geometry, the length and the excitation frequency. By placing only one piezoelectric transducer on the top or the bottom surface of the plate and weakening the strength of one mode while enhancing the strength of the other modes to find the centre frequency, with which the peak wave amplitude ratio between the S0 and A0 modes is maximum, a single mode excitation from the multiple modes of the Lamb waves can be achieved approximately. Experimental data are presented to show the validity of the analyses. The results are used to optimize the Lamb wave detection system.     

Estimation of wall thinning in mild steel using laser ultrasound Lamb waves and a non-steady-state photo-emf detector

In this work, a non-steady-state photo-emf receiver has been used to detect the lower frequency fundamental a0 Lamb waves in mild steel. Experimentally, the Lamb waves are laser-generated in the thermoelastic regime using a Q-switched, 20 ns, pulsed Nd:YAG laser and a line source. Typical Lamb waves had centre frequencies of 250 kHz but with frequency components that extended beyond 1 MHz. In mild steel, higher order Lamb wave modes were not considered to be significant below a frequency thickness product of 1.6 MHz mm. Below this level, associated velocity dispersion curve offered phase velocity changes that were sensitive to thickness change. Samples up to 5 mm in thickness were examined without significant interference from higher order modes. A non-steady-state photo-emf detector used as the ultrasonic detector had the advantage of a lower frequency cut-off at 100 kHz compared to a confocal Fabry-Pérot interferometer (CFPI) of about 2 MHz. Both schemes offered greater stand-off distance (>20 cm) than is possible with EMATs, which have a stand-off distance less than 1.0 mm. Progress made in detecting wall thinning in steel plate with thickness up to 5 mm is reported.     

多通道超声兰姆波检测板状结构中的裂纹

超声兰姆(Lamb)波在结构缺陷检测方面愈来愈受到重视,但目前Lamb波的应用局限于单信号源激励,单通道接收的方法,容易受到噪声干扰,其后续的信号分析处理也比较复杂。本文旨在采用多通道Lamb波对板状结构中的裂纹进行定量分析与诊断。在铝板的表面凿刻出不同深度的凹槽作为裂纹,通过线阵换能器采集在一定传播距离内的多通道Lamb波信号,并采用二维傅里叶变换分析在不同深度的裂纹下,Lamb波模式能量的变化规律。结果表明,相对于完好铝板中的Lamb波信号,裂纹的存在会使Lamb波发生模式转换现象,并且转换模式能量百分比随裂纹深度的增加而线性增加。其结果为Lamb波评价板状结构中的裂纹状况提供了一种可能的方法。     

小样本字典学习的兰姆波模态识别方法*

针对兰姆波多模态识别问题,提出了基于小样本字典学习的模态识别方法。将多层复合板的频散特性看作一个线性时不变系统,首先,根据频散知识模拟各个模态传播特定距离后的信号,提取走时和能量特征创建字典;其次,获取待测信号的走时特征,通过查询字典来识别兰姆波模态;最后,根据能量参数估计结果,实现待测信号中各模态信号的分离和重构。通过对三层粘接的AAA板(铝板-亚克力板-铝板,每层厚度为2mm)中传播距离为0.3m、0.5m的直达波和反射波的实验验证,结果显示该方法对A0、S0模态的有效识别和各个波包信号的准确重建。     

Localization of notches with Lamb waves

A time-frequency representation (TFR) is used to analyze the interaction of a multimode and dispersive Lamb wave with a notch, and then serves as the basis for a correlation technique to locate the notch. The experimental procedure uses a laser source and a dual-probe laser interferometer to generate and detect Lamb waves in a notched plate. The high fidelity, broad-bandwidth, point-like and noncontact nature of laser ultrasonics are critical to the success of this study, making it possible to experimentally measure transient Lamb waves without any frequency biases. A specific TFR, the reassigned spectrogram, is used to resolve the dispersion curves of the individual modes of the plate, and then the slowness-frequency representation (SFR) of the plate is calculated from this reassigned spectrogram. By considering the notch to be an additional (second) source, the reflected and transmitted contributions of each Lamb mode are automatically identified using the SFRs. These results are then used to develop a quantitative understanding of the interaction of an incident Lamb wave with a notch, helping to identify mode conversion. Finally, two complementary, automated localization techniques are developed based on this understanding of scattering of Lamb waves.     

用于储罐底板缺陷检测的超声兰姆波模式研究

从超声兰姆波的声场方程出发,得到板材表面离面位移(法向位移)为零的条件,即当超声兰姆波的相速度等于板材介质的纵波声速时,在板材表面的离面位移为零。在给定适当频厚积的条件下,分别数值模拟了仅有切向位移而无离面位移的A1、S1、A2和S2兰姆波模式在有液体负载的单层钢板中的传播情形。结果表明:离面位移为零的S2模式频散较小且对板中缺陷更为敏感。     

非线性兰姆波在阶梯板中传播的有限元仿真

在非线性兰姆波检测中,累积二次谐波是重要的检测信号.该文利用有限元法仿真了非线性兰姆波在阶梯板中的产生和传播过程,通过二维离散傅里叶变换分析了兰姆波的传播模态和各个模态通过波导横截面的能流大小,给出了各个模态在阶梯板中的反射、透射系数,总结了其随阶梯板厚度的变化规律.研究发现,随着台阶增高,散射效应使得兰姆波更难入射波...     

不锈钢折弯板裂纹Lamb波检测技术*

金属弯板广泛应用于车辆、船舶、飞机等大型装备结构件中，折弯处易形成应力集中产生裂纹，直接影响构件的使用安全和寿命。本文开展了不锈钢弯板裂纹缺陷Lamb波检测技术研究，计算了钢板的频散曲线，优选三种不同频率的S0模态：0.25MHz、0.5MHz、1MHz。利用COMSOL软件建立频域仿真模型，模拟了Lamb波在3mm厚“L”形弯板内部的传播情况，开展折弯板裂纹缺陷检测实验，并使用小波包变换的方法对实验信号进行分析。结果表明，经小波变换后，0.25MHz、0.5MHz、1 MHz的S0模态Lamb波均可用于裂纹缺陷的识别检测.     

Time reversal technique for health monitoring of metallic structure using Lamb waves

Time reversal active sensing using Lamb waves is investigated for health monitoring of a metallic structure. Experiments were conducted on an aluminum plate to study the time reversal behavior of A₀ and S₀ Lamb wave modes under narrow band and broad band pulse excitation. Damage in the form of a notch was introduced in the plate to study the changes in the characteristics of the time reversed Lamb wave modes experimentally. Time–frequency analysis of the time reversed signal was carried out to extract the damage information. A measure of damage based on wavelet transform was derived to quantify the hidden damage information in the time reversed signal. It has been shown that time reversal can be used to achieve temporal recompression of Lamb waves under broadband signal excitation. Further, the broad band excitation can also improve the resolution of the technique in detecting closely located defects. This is demonstrated by picking up the reflection of waves from the edge of the plate, from a defect close to the edge of the plate and from defects located near to each other. This study shows the effectiveness of Lamb wave time reversal for temporal recompression of dispersive Lamb waves for damage detection in health monitoring applications.     

Measurements of dispersion curves of leaky Lamb waves using a lensless line-focus transducer.

This paper presents a new method of measuring dispersion curves of leaky Lamb waves propagating in a thin plate. The measurement system is based on a lens-less line-focus transducer and its defocusing measurement technique. A new waveform processing method known as V(f, z) method is introduced for analyzing the measured waveforms and for extracting the dispersion relation. For two thin-plate samples, namely a 150 microm thick alumina plate and a 320 microm thick stainless steel plate, the dispersion curves of several lower order modes of leaky Lamb waves have been experimentally determined in the frequency range of few to 25 MHz. The experimental dispersion curves have then been compared with the theoretical ones. Excellent agreement is observed. It is then verify that this method indeed provides a convenient and accurate way for experimentally measuring dispersion curves of leaky Lamb waves of thin-plate samples.     

Magnetoelastic waves in an in-plane magnetized ferromagnetic plate

The spectrum of magnetoelastic waves propagating along the magnetic field in an in-plane magnetized ferromagnetic plate is numerically investigated in the exchangeless approximation. No restrictions are imposed either on the field pattern of backward volume magnetostatic waves (BVMSWs) or elastic waves supported by a plate of a given geometry across the plate or on the relationship between the sound velocity v _S and the phase velocity of the magnetoelastic waves v=ω/q (ω is the frequency, q is the wave number). The resonance interaction of the BVMSWs and elastic waves is accompanied, as a rule, by the formation of “stop” bands δω that are proportional to the magnetoelastic coupling constant b. When the BVMSWs are in resonance with Lamb and shear elastic modes the values of the magnetoelastic gaps δω at v≈v _S turn out to be of the same order. For v≫v _S , the efficiency of the interaction between the BVMSWs and transverse Lamb modes is almost one order of magnitude higher. If the frequency spacing Δω between the elastic modes is smaller than the mag-netoelastic gap in the spectrum (Δω≤δω), which takes place, particularly, in the region of crowding the elastic mode spectrum (v≈v _S), the resonant interaction results in mixing the dispersion laws for the elastic modes. Namely, a surface mode may transform into a volume one and a shear mode, into the Lamb mode or into a shear mode with another number. The resonance interaction of the shear and Lamb elastic modes not only forms the magnetoelastic gaps δω∼b ² but also changes the efficiency of elastic wave coupling with the magnetic subsystem. This may show up as the coexistence of the effects of “repulsing” both the dispersion laws and the damping decrements of the elastic waves at the resonance frequency. It is shown that magnetostriction splits the cutoff frequencies of both transverse Lamb modes and shear modes, as well as the long-wave (q → 0) frequency limits f ₀ of the BVMSW modes. This may cause the resonance interaction between BVMSW modes of equal evenness in a narrow frequency band Δ∼b near f ₀.     

Wideband dispersion removal and mode separation of Lamb waves based on two-component laser interferometer measurement

Ultrasonic Lamb waves are considered as a sensitive and effective tool for nondestructive testing and evaluation of plate-like or pipe-like structures. The nature of multimode and dispersion causes the wave packets to spread, and the modes overlap in both time and frequency domains as they propagate through the structures. By using a two-component laser interferometer technique, in combination with a priori knowledge of the dispersion characteristics and wave structure information of Lamb wave modes, a two-component signal processing technique is presented for implementing dispersion removal and mode separation simultaneously for two modes mixture signals of Lamb waves. The proposed algorithm is first processed and verified using synthetic Lamb wave signals. Then, the two-component displacements test experiment is conducted using different aluminum plate samples. Moreover, we confirm the effectiveness and robustness of this method.     

铝板中Lamb波检测的实验研究

Lamb波在传播过程中具有频散及多模态特性,若相关参数选择不当,会导致在实际应用中信号相互叠加而无法识别。本文基于Lamb波的频散曲线是其频散方程实数解分布的特点,采用二分法绘制了铝板中Lamb波的频散曲线、波结构曲线和入射角曲线。根据曲线选择S0模态的Lamb波对1mm厚铝板中不同类型的缺陷进行检测。实验结果表明,S0模态的Lamb波对裂纹型缺陷和贯穿型缺陷十分敏感,但对于裂纹型缺陷,其幅值变化并不与缺陷大小成线性关系,并且S0模态Lamb波的声场指向性十分集中,在偏离声束轴线时无法检测到缺陷。     

基于频散补偿和分数阶微分的多模式兰姆波分离

由于兰姆波的多模和频散特性,实际检测时在同一激发频率下存在多种模式的混合信号,而各模式信号有不同的频散特性,使得在时频混叠的情况下兰姆波的检测变得十分复杂.本文在频散补偿的基础上,通过时延函数建模,依靠不同模式频散趋势的差异性,将时频混叠信号的分离问题转化为部分模式混叠信号的分离问题.基于分数阶微分的理论,用信号幅值谱分数阶微分极大值和对应频率分别与微分阶次拟合多项式实现特征参数的提取并依靠特征参数重建幅值谱.结合相位谱重构时域信号以实现部分混叠信号中频散补偿后的模式的分离.最后恢复频散获得分离后的兰姆波信号.仿真和实验结果表明,本文方法不仅可以实现时频混叠多模式兰姆波信号的分离,更能保证分离精度,有助于复杂多模式频散信号的分离与处理的进一步研究.     

The effect of surface stress on the propagation of Lamb waves

This work investigates the possibility of the propagation of Lamb waves in thin solid layers with external traction free surfaces, in the presence of surface elasticity, inertia and residual stress. It is demonstrated that such waves do exist and that their characteristics can be quite different from their classical counterparts. The governing equations with non-classical boundary conditions involving the bulk and surface stress are solved exactly in the frequency-wavenumber domain. This solution is utilized to compute the Lamb wave modes for different layer thicknesses. An efficient strategy to capture all the modes of Lamb waves within a given frequency window is outlined. It is shown that the effect of surface elasticity and inertia becomes significant with increasing frequency and decreasing layer thickness, where the number of modes participating within a given frequency window is more than that permitted by the classical theory. Further, it is observed that the nature of the Lamb wave modes (in terms of negative dispersion) in the presence of surface stress is similar to what predicted by the nonlocal theory and microstructure based continuum theory.     

Lamb mode reflections at the end of a plate loaded by a viscoelastic material

This paper deals with a study of the conversion of a Lamb wave at the loaded edge of a plate. An experimental study is performed to know the interaction of surface waves with a viscoelastic material. A Lamb wave is generated by a wedge. At the end of the plate, this wave gives rise to several reflected waves. A first study makes it possible qualitatively to know the Lamb modes present in reflection. Secondly, conversion phenomena are studied to know if surface waves are sensitive to evolution in the time of the viscoelastic material structure. The selected material is a sol-gel containing silica.     

Laser-ultrasonic generation of Lamb waves in the reaction force range

The Laser-ultrasonic generation of Lamb waves in an elastic plate is investigated theoretically and experimentally for a laser source whose intensity is high enough to create reaction forces (normal tractions) on the illuminated surface of the specimen. The analytical solutions for transient waves are derived using the integral transform method first by considering an arbitrary source shape and time excitation function, and then specifically for circular and line source shapes. The simulation study allows us not only to predict the behavior of individual wave modes but also to construct the overall responses; thus it helps us better understand the wave excitation mechanisms. The dispersive and multi-modal nature of laser-generated Lamb waves is presented by showing the spatiotemporal Fourier transform of displacements obtained by the simulation study. The transform, displayed in the frequency-wave number domain, enunciates the characteristics of the propagating individual Lamb wave modes. The simulation results are then compared with the 2-D Fourier transform of a set of experimental data obtained by scanning an aluminum plate specimen.     

Transient Lamb waves: comparison between theory and experiment

This paper presents an experimental investigation of the generation of transient Lamb waves inside an immersed plate by a time limited signal. The transient Lamb waves are the solutions of the characteristic equation of the plate for complex frequency and real slowness, in contrast to the leaky Lamb waves, for which the slowness is complex and the frequency is real. By using a large transducer in agreement with the real slowness assumption, the excitation of these transient Lamb waves is observed experimentally both in reflection and transmission for a tone burst excitation. Particular attention is paid to the A0 mode for which the amplitude increases exponentially in time. As a result, the total reflected waveform contains in this case a transient contribution, coming from the generation of the A0 mode, that precedes the forced regime. It is shown that there is a very good agreement between the theoretical and the experimental time exponential amplitude variations of the transient Lamb waves. For the A0 mode, the transient signal is qualitatively explained by a group velocity higher than the phase velocity.