Synergetic Photocatalytic Nanostructures Based on Au/TiO2/Reduced Graphene Oxide for Efficient Degradation of Organic Pollutants

Recently, there is crucial interest in the design and fabrication of nanocatalysts for efficient decomposition of organic pollutants in wastewater using visible light. This work reports the assembling fabrication of synergetic photocatalytic Au/TiO₂/RGO nanostructures by utilizing the reduced graphene oxide (RGO) as substrate material and efficient separator for electrons and holes. The Au/TiO₂ nanostructures with a ≈7 nm TiO₂ particles size are dispersed uniformly on RGO nanosheets. UV–vis diffuse reflectance spectroscopy verifies that Au/TiO₂/RGO nanocomposites show strong absorption of visible light. The degradation efficiency after 1 h for hydroquinone under visible light and UV light is ≈77% and ≈90%, respectively. Under visible light, the calculated apparent rates (k ) of the Au/TiO₂/RGO nanocomposites are 0.0112 and 0.0174 min^?1 for decomposition of methylene blue and hydroquinone. That are five times greater than that of bare TiO₂. The high photocatalytic activity is mainly attributed to the synergy between RGO and Au/TiO₂ nanostructure. The strategy of composite nanostructures assembling on RGO is ensured to have a great practicable potential for the designing of high efficient multielement composite nanoparticles catalysts.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Enhanced visible light photocatalytic properties of Fe-doped TiO2 nanorod clusters and monodispersed nanoparticles

In order to get photocatalysts with desired morphologies and enhanced visible light responses, the Fe-doped TiO₂ nanorod clusters and monodispersed nanoparticles were prepared by modified hydrothermal and solvothermal method, respectively. The microstructures and morphologies of TiO₂ crystals can be controlled by restraining the hydrolytic reaction rates. The Fe-doped photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis absorption spectroscopy (UV-vis), N₂ adsorption-desorption measurement (BET), and photoluminescence spectroscopy (PL). The refinements of the microstructures and morphologies result in the enhancement of the specific surface areas. The Fe³⁺-dopants in TiO₂ lattices not only lead to the significantly extending of the optical responses from UV to visible region but also diminish the recombination rates of the electrons and holes. The photocatalytic activities were evaluated by photocatalytic decomposition of formaldehyde in air under visible light illumination. Compared with P25 (TiO₂) and N-doped TiO₂ nanoparticles, the Fe-doped photocatalysts show high photocatalytic activities under visible light.     

Ti<Superscript>3+</Superscript>-doped TiO<Subscript>2</Subscript> hollow sphere with mixed phases of anatase and rutile prepared by dual-frequency atmospheric pressure plasma jet

A novel method of synthesizing Ti³⁺-doped TiO₂ was proposed. Ti³⁺-doped TiO₂ hollow spheres were prepared with different thickness of carbon shell by using atmospheric pressure plasma jet generated by dual-frequency power sources. The as-synthesized Ti³⁺-doped TiO₂ hollow microspheres were characterized by X-ray diffraction (XRD) pattern, scanning electron microscope (SEM) images, high-resolution transmission electron microscopy (HRTEM) images, Raman spectra, X-ray photoelectron spectroscopy (XPS), and UV–vis spectra. These results indicated that these samples had mixed phases of anatase and rutile and the structure of hollow sphere varied with different thickness of carbon shell. The Ti-O-C chemical bond was the connection between the TiO₂ hollow sphere and carbon layer. Amount of Ti³⁺ ions were found, which were accompanied with the formation of oxygen vacancies. Meantime, the as-synthesized catalysts also display strong absorption in the visible light region and have a narrow band energy gap. Optical emission spectroscopy (OES) was used to observe different excited species in the discharge area. These results showed that the oxygen content had a significant impact on the number of oxygen vacancies. Finally, the photocatalytic activities of as-prepared samples were evaluated by decomposition of rhodamine B aqueous solution, which showed better photocatalytic activity under UV–vis light irradiation.     

Fabrication of Fe-doped TiO2 nanoparticles and investigation of photocatalytic decolorization of reactive red 198 under visible light irradiation

In this research, Fe-doped TiO₂ nanoparticles with various Fe concentrations (0. 0.1, 1, 5 and 10 wt%) were prepared by a sol–gel method. Then, nanoparticles were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray analysis (EDX), BET surface area, photoluminescence (PL) spectroscopy and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of the nano-particles was evaluated through degradation of reactive red 198 (RR 198) under UV and visible light irradiations. XRD results revealed that all samples contained only anatase phase. DRS showed that the Fe doping in the titania induced a significant red shift of the absorption edge and then the band gap energy decreased from 3 to 2.1 eV. Photocatalytic results indicated that TiO₂ had a highest photocatalytic decolorization of the RR 198 under UV irradiation whereas photocatalytic decolorization of the RR 198 under visible irradiation increased in the presence of Fe-doped TiO₂ nanoparticles. Among the samples, Fe-1 wt% doped TiO₂ nanoparticles showed the highest photocatalytic decolorization of RR198 under visible light irradiation.     

Nitrogen doped TiO2 nanoparticles decorated on graphene sheets for photocatalysis applications

Nitrogen doped TiO₂ nanoparticles decorated on graphene sheets are successfully synthesized by a low-temperature hydrothermal method. The resulting GR-N/TiO₂ composites are characterized by X-Ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), X-Ray photoelectron spectroscopy (XPS) and Transmission Electron Microscopy (TEM). The optical properties are studied using UV–visible diffuse reflectance spectroscopy (DRS), which confirms that the spectral responses of the composite catalysts are extended to the visible-light region and show a significant reduction in band gap energy from 3.18 to 2.64 eV. Photoluminescence emission spectra verify that GR-N/TiO₂ composites possess better charge separation capability than pure TiO₂. The photocatalytic activity is tested by degradation of methyl orange (MO) dye under visible light irradiation. The results demonstrate that GR-N/TiO₂ composites can effectively photodegrade MO, showing an impressive photocatalytic enhancement over pure TiO₂. The dramatically enhanced activity of composite photocatalysts can be attributed to great adsorption of dyes, enhanced visible light absorption and efficient charge separation and transfer processes. This work may provide new insights into the design of novel composite photocatalysts system with efficient visible light activity.     

Visible Light Photocatalytic Functional TiO2/PVDF Nanofibers for Dye Pollutant Degradation

The photodegradation of poly(vinylidene fluoride) (PVDF)/titanium oxide (TiO₂) nanofibers under visible light is described, something that has not been previously reported in the literature. Visible light photocatalytic electrospun PVDF/TiO₂ nanofiber webs with anatase TiO₂ concentration varying from 0% to 20% (0%, 1%, 3%, 5%, 10%, and 20%) are produced, and their ability to degrade a toxic pollutant, Rhodamine B (RhB), is studied. Photodegradation study using UV–vis spectroscopy on PVDF/TiO₂ nanofiber webs (with TiO₂ concentration of 20%) shows that 80% of RhB is degraded within 6 h at the wavelength of 546 nm, which clearly falls within the visible spectra. The color of RhB solvent catalyzed by PVDF/TiO₂ nanofiber webs gradually changes from red to orange, then to yellow, further to light yellow till colorless, which suggests the complete photodegradation of RhB under visible light. To estimate the rate of photodegradation, the reaction constant k is calculated. Based on the k value, PVDF/TiO₂ nanofiber webs with 20% TiO₂ concentration show the highest degradation rate compared to other PVDF/TiO₂ nanofiber webs and pure TiO₂ nanoparticles. This study proves the viability of TiO₂‐based nanofibers to have catalytic capabilities under low‐energy visible light.     

铈和磷钨酸共掺杂纳米二氧化钛中空纤维的制备及其光催化活性

以棉花纤维为模板,以钛酸四正丁酯、硝酸铈铵和磷钨酸为原料采用模板法制备了一系列铈和磷钨酸共掺杂的、具有中空纤维结构的TiO₂光催化材料, 利用扫描电子显微镜、X射线衍射、BET和紫外-可见光谱等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征. 以苯酚溶液的光催化降解为模型反应,考察了不同掺杂量的样品在紫外和可见光下的光催化性能. 结果表明,用模板法制备的TiO₂纤维材料具有中空结构,共掺杂的TiO₂纤维在紫外和可见光条件下较纯TiO₂纤维和单掺杂TiO₂纤维对苯酚溶液具有更好的光催化降解效果, 且铈和磷钨酸的掺杂量显著影响该纤维材料的催化性能;当铈掺杂量为0.3mol%和磷钨酸掺杂量为2mol%,在500 oC焙烧2 h所得中空纤维材料的催化性能最佳,4 h即可使苯酚溶液的降解率达98.5%;重复使用4次仍可使苯酚溶液的降解率保持在87%以上,且该催化剂材料易于离心分离去除.     

Properties of carbon and iron modified TiO2 photocatalyst synthesized at low temperature and photodegradation of acid orange 7 under visible light

The nanoparticles of TiO₂ modified with carbon and iron were synthesized by sol-gel followed solvothermal method at low temperature. Its chemical composition and optical absorption were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence emission spectroscopy (PL), UV-vis absorption spectroscopy, and electron paramagnetic resonance (EPR). It was found that carbon and iron modification causes the absorption edge of TiO₂ to shift the visible light region. Fe(III) cation could be doped into the matrix of TiO₂, by which could hinder the recombination rate of excited electrons/holes. Superior photocatalytic activity of TiO₂ modified with carbon and iron was observed for the decomposition of acid orange 7 (AO7) under visible light irradiation. The synergistic effects of carbon and iron in modified TiO₂ nanoparticles were responsible for improving visible light photocatalytic activity.     

Sol-gel derived S,I-codoped mesoporous TiO2 photocatalyst with high visible-light photocatalytic activity

A mesoporous S,I-codoped TiO₂ photocatalyst with high visible light photocatalytic activity was synthesized through the hydrolysis and condensation of titanium isopropoxide with thiourea and iodic acid as the precursors. The as-prepared catalysts were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), UV-vis diffuse reflectance (DRS), X-ray photoelectron spectroscopy (XPS), Fourier translation infrared spectroscopy (FT-IR), and N₂ adsorption. The results showed that the cations of S⁶⁺ and I⁵⁺ could substitute for some of the lattice titanium (Ti⁴⁺). The S,I-codoping forms the new bands above the valence band and narrows the band-gap of the TiO₂, then shifts the absorption edge from UV light region to visible light range. The activity of the catalyst was examined by photodegradation of methylene blue in an aqueous solution under visible light irradiation. The activity of the S,I-codoped catalyst is far superior to that of single S or I-doped TiO₂ counterpart. The high visible light photocatalytic activity could be attributed to the strong absorption of light, well-crystalline anatase phase, and mesoporous microstructure.     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

Enhanced photocatalytic activity and stability of nano-scaled TiO2 co-doped with N and Fe

Titanium dioxide (TiO₂) nanoparticles co-doped with N and Fe were prepared via modified sol-gel process. The products were characterized by transmission electron microscopy (TEM), N₂ adsorption, X-ray diffraction (XRD), Raman spectroscopy, UV-vis spectroscopy, photoluminescence (PL), and X-ray photoelectron spectroscopy (XPS). It is shown that the prepared TiO₂ particles were less than 10 nm with narrow particle size distribution. The addition of MCM-41 caused the formation of Ti-O-Si bond which fixed the TiO₂ on MCM-41 surface, thus restricted the agglomeration and growth of TiO₂ particles. The photocatalytic performance in the degradation of methylene blue showed that N, Fe co-doped TiO₂ exhibited much higher photocatalytic activity than doped sample with nitrogen or Fe³⁺ alone under both UV and visible light. N, Fe co-doping decreased the loss of doping N during the degradation reaction, thus increased the photocatalytic stability. It was also found that the nitridation time had significant influence on the photocatalytic activity of prepared TiO₂ catalysts.     

Improvement in the photocatalytic activity of TiO2 by the partial oxidation of the C impurities

TiO₂ was treated by water in an ultrasonic bath, resulting in the enhancement of the photocatalytic activity for the decomposition of methylene blue under UV and visible light irradiation. No change in the crystallinity and optical properties of TiO₂ by the H₂O-treatment was observed. The X-ray photoelectron spectroscopy (XPS) and FT-IR data revealed that the C impurities were oxidized by this treatment, indicating that the change in the structure of the C impurities plays a pivotal role in the photocatalytic activity of TiO₂.     

TiO2–carbon nanotube composites for visible photocatalysts – Influence of TiO2 crystal structure

We investigated the influence of the crystal structure of TiO₂ and the use of different TiO₂ precursors on the properties and photocatalytic activity of carbon nanotube (CNTs)–titania composites. We found that the crystal structure and properties of starting TiO₂ nanomaterial significantly affected the effect of CNTs incorporation on the photocatalytic activity under simulated solar and visible light illumination (simulated solar illumination with UV-blocking filter). In case of significant photocatalytic activity under visible light illumination (anatase TiO₂), likely due to the presence of native defects, composites exhibited lower activity under visible illumination only, but higher activity under simulated solar illumination. The opposite trends were observed for P25 (anatase + rutile) and rutile TiO₂, where incorporation of CNTs resulted in a significant increase of photocatalytic activity under visible illumination. Thus, control over crystal structure and native defects is essential for the development of efficient visible light activated photocatalysts.     

Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.     

Preparation and characterization of TiO2 photocatalysts co-doped with iron (III) and lanthanum for the degradation of organic pollutants

Titanium dioxide photocatalysts co-doped with iron (III) and lanthanum were prepared by a facile sol-gel method. The structure of catalysts was characterized by X-ray diffraction (XRD), Raman spectroscopy, UV-vis diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the samples were evaluated by the degradation of methylene blue in aqueous solutions under visible light (λ > 420 nm) and UV light irradiation. Doping with Fe³⁺ results in a lower anatase to rutile (A-R) phase transformation temperature for TiO₂ particles, while doping with La³⁺ inhibits the A-R phase transformation, and co-doping samples indicate that Fe³⁺ partly counteracts the effect of La³⁺ on the A-R transformation property of TiO₂. Fe-TiO₂ has a long tail extending up the absorption edges to 600 nm, whereas La-TiO₂ results in a red shift of the absorption. However, Fe and La have synergistic effect in the absorption of TiO₂. Compared with Fe³⁺ and La³⁺ singly doped TiO₂, the co-doped simple exhibits excellent visible light and UV light activity and the synergistic effect of Fe³⁺ and La³⁺ is responsible for improving the photocatalytic activity.     

镧掺杂介孔TiO2光催化剂的制备、表征及其光催化性能

以钛酸四正丁酯和硝酸镧为原料, 以P123为模板剂,采用模板法合成了La掺杂型介孔TiO₂光催化剂, 借助TGA-DSC、BET、XRD及UV-Vis等测试手段对样品进行了表征,并以苯酚为模型污染物考察了镧掺杂量对样品光催化活性的影响．结果表明: La掺杂介孔TiO₂光催化剂孔径分布较均匀(～10 nm),比表面积可达165 m²/g．与纯介孔TiO₂相比,经掺杂改性后的样品在紫外光区及可见光区的吸收显著增强,对光具有更高的利用率,La掺杂可显著提高介孔TiO₂的光催化活性.     

Preparation and photocatalytic activity of nitrogen-doped TiO2 hollow nanospheres

TiO₂ hollow nanospheres were prepared using silicon oxide as a template. N-doped titanium oxide hollow spheres, TiO_2−xN_x were synthesized by reacting TiO₂ hollow spheres with thiourea at 500 °C. XRD and XPS data showed that oxygen was successfully substituted by nitrogen through the nitrogen-doping reaction, and finally N-doped TiO₂ hollow spheres were formed. The N-doped TiO₂ hollow spheres showed new absorption shoulder in visible light region so that they were expected to exhibit photocatalytic activity in the visible light. The photocatalytic activity of N-doped TiO₂ hollow spheres under visible light was similar to that of normal spherical TiO_2−xN_x in spite of the structural difference.     

Study on the photocatalytic activity of TiN/TiO2 nanoparticle formed by ball milling

TiN/TiO₂ nanoparticle photocatalyst was prepared by ball milling of TiO₂ in H₂O solution doped with TiN. The photocatalyst was characterized by UV–Vis diffuse reflection spectroscopy, X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Based on the results of the characterization, the mechanism of the increase in photocatalytic activity was investigated. The results show that when the amount of doped TiN is 0.15 wt%, the photocatalytic activity of the TiN/TiO₂ is at its peak. Compared with TiO₂, the photoabsorption wavelength range of the TiN/TiO₂ photocatalyst red-shifts about 30 nm, and the photoabsorption intensity increases as well. The photocatalytic activities of the photocatalyst are higher than that of TiO₂ under UV and visible light irradiation. The increase of surface Ti³⁺ reactive center and the extension of the photoabsorption wavelength are the main factors for the increase in the photocatalytic activity of the TiN/TiO₂. Doped TiN neither changes the TiO₂ crystal phase nor creates new crystal phase by ball milling.