Characterization and activity of visible-light-driven TiO2 photocatalyst codoped with lanthanum and iodine

The novel visible-light-activated La/I/TiO₂ nanocomposition photocatalyst was successfully synthesized using precipitation-dipping method, and characterized by X-ray powder diffraction (XRD), the Brunauer-Emmett-Teller (BET) method, transmission electron microscopy (TEM), thermogravimetry-differential scanning calorimetry (TG-DSC) and UV-vis diffuse reflectance spectroscopy (UV-vis DRS). The photocatalytic activity of La/I/TiO₂ was evaluated by studying photodegradation of reactive blue 19 as a probe reaction under simulated sunlight irradiation. Photocatalytic experiment results showed that the maximum specific photocatalytic activity of the La/I/TiO₂ photocatalyst appeared when the molar ratio of La/Ti was 2.0 at%, calcined at 350 °C for 2 h, due to the sample with good crystallization, high BET surface area and small crystal size. Under simulated sunlight irradiation, the degradation of reactive blue 19 aqueous solution reached 98.6% in 80 min, which showed La/I/TiO₂ photocatalyst to be much higher photocatalytic activity compared to standard Degussa P25 photocatalyst. The higher visible light activity is due to the codoping of lanthanum and iodine.     

Synthesis of S/Cr doped mesoporous TiO2 with high-active visible light degradation property via solid state reaction route

S/Cr doped mesoporous TiO₂ (S-TiO₂, Cr-TiO₂, S-Cr-TiO₂) were successfully synthesized via a simple, effective and environmental benign solid state reaction route. The low angle XRD patterns demonstrated that the resulting samples possess mesostructures. The further characterizations via N₂ adsorption-desorption and XPS showed that the typical S/Cr co-doped mesoporous TiO₂ (S-Cr-TiO₂(5S-5Cr)) possesses mesopore with the high specific surface area of 118.4 m²/g and narrow pore size distribution, and both S and Cr have been incorporated into the lattice of TiO₂ with the amounts of 4.16% sulfur and 7.88% chromium, respectively. And Raman spectroscopy shows that the surface of S-Cr-TiO₂ (5S-5Cr) material possesses stretching vibrational peaks at ∼709, ∼793 cm⁻¹ are assignable to the Ti-O-Cr, O-Cr (Ti)-OH bonds, respectively. Interestingly, the UV-vis displayed that the absorption regions of S/Cr doped mesoporous TiO₂ cover the visible light region. As for the series of S-Cr-TiO₂ samples, the absorption region even extends to near infrared region with strong adsorption. Moreover, compared with the pure titanium dioxide (P25-TiO₂), the photodegradation properties of bromocresol green (BCG) on the S/Cr doped mesoporous TiO₂ showed excellent photocatalytic properties under visible light irradiation. Within 50 min visible light irradiation, 82.6% of the initial BCG was degraded for the S-Cr-TiO₂ (6S-4Cr) photocatalyst.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Aerosol-assisted flow synthesis of WxTi1−xO2 solid solution spheres with enhanced photocatalytic activity

In this paper, W_xTi_1−xO₂ solid solutions (x = 0.000, 0.005, 0.010, 0.015, and 0.020) microspheres were synthesized with an aerosol-assisted flow synthesis method. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), nitrogen sorption, UV-vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The photocatalytic activities of the as-prepared catalysts were measured by the degradation of rhodamine B (RhB) under visible light irradiation (λ ≥ 420 nm). All the solid solutions exhibited higher photocatalytic activities than pure TiO₂ and the W_0.015Ti_0.985O₂ solid solution possessed the highest photocatalytic activity. The degradation constant of RhB on W_0.015Ti_0.985O₂ solid solution catalyst was about 15 times of that of the pure TiO₂ and 25 times of that of Degussa P25, respectively. This study provides an effective method to prepare visible light photocatalysts on a large scale.     

Preparation and visible light photocatalytic activity of mesoporous N, S-codoped TiO2(B) nanobelts

The mesoporous N, S-codoped TiO₂(B) nanobelts are synthesized via hydrothermal synthesis and post-treatment, and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), N₂ adsorption-desorption measurements (BET), X-ray photoelectron spectra (XPS), and UV-vis diffuse reflectance spectra (DRS). The results show that the prepared samples are mesoporous structured and exhibit stronger absorption in the visible light region with red shift in the absorption edge. The photocatalytic activity of N, S-codoped mesoporous TiO₂(B) nanobelts is evaluated by the photocatalytic photodegradation of potassium ethyl xanthate (KEX) under visible light irradiation. It is found that the photocatalytic activity of the prepared samples increases with increasing the molar ratio of thiourea to Ti (R). At R = 3, the photocatalytic activity of the N, S-codoped TiO₂(B) sample TBLTS-3 reaches a maximum value. With further increasing R, the photocatalytic activity of the sample decreases. The high photocatalytic activity of N, S-codoped TiO₂(B) nanobelts can be attributed to the balance between strong absorption in visible light region and low recombination rate of electron/hole pairs.     

Low temperature synthesis of iodine-doped TiO2 nanocrystallites with enhanced visible-induced photocatalytic activity

Iodine-doped TiO₂ nanocrystallites (denoted as I-TNCs) were prepared via a newly developed triblock copolymer-mediated sol-gel method at a temperature of 393 K. I-doping, crystallization and the formation of porous structure have been simultaneously achieved. The obtained particles were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and UV-vis spectrophotometer. The results indicated that the as-prepared I-TNCs possessed a diameter of ca. 5 nm with anatase crystalline structure and a specific surface area of over 200 m² g⁻¹. The presence of iodine expanded the photoresponse in visible light range, and led to enrich in surface hydroxyl group on the TiO₂ surface. Compared with the commercial photocatalyst P25, the I-TNCs significantly enhanced the photocatalytic efficiency in the degradation of rhodamine B and 2,4-dichlorophenol, and the I-TNCs with 2.5 mol% doping ratio exhibited the best photocatalytic activity.     

Preparation and characterization of Fe-doped TiO2 on fly ash cenospheres for photocatalytic application

Fe³⁺-doped TiO₂ film deposited on fly ash cenosphere (Fe-TiO₂/FAC) was successfully synthesized by the sol-gel method. These fresh photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermogravimetric analyses (TGA). The XRD results showed that Fe element can maintain metastable anatase phase of TiO₂, and effect of temperature showed rutile phase appears in 650 °C for 0.01% Fe-TiO₂/FAC. The SEM analysis revealed the Fe-TiO₂ films on the surface of a fly ash cenosphere with a thickness of 2 μm. The absorption threshold of Fe-TiO₂/FACs shifted to a longer wavelength compared to the photocatalyst without Fe³⁺-doping in the UV-vis absorption spectra. The photocatalytic activity and kinetics of Fe-TiO₂/FAC with varying the iron content and the calcination temperatures were investigated by measuring the photodegradation of methyl blue (MB) during visible light irradiation. Compared with TiO₂/FAC and Fe³⁺-doped TiO₂ powder (Fe-TiO₂), the degradation ratio using Fe-TiO₂/FAC increased by 33% and 30%, respectively, and the best calcined temperature was 450 °C and the optimum doping of Fe/Ti molar ratio was 0.01%. The Fe-TiO₂/FAC particles can float in water due to the low density of FAC in favor of phase separation to recover these photocatalyst after the reaction, and the recovery test shows that calcination contributes to regaining photocatalytic activity of Fe-TiO₂/FAC photocatalyst.     

Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

Photoactive materials prepared by homogeneous hydrolysis with thioacetamide: Part 2—TiO2/ZnO nanocomposites

Photocatalytic active titanium dioxide (TiO₂)/zinc oxide (ZnO) composite was prepared by homogeneous hydrolysis of a mixture of titanium oxo-sulphate and zinc sulphate in aqueous solutions with thioacetamide and subsequent annealing at the temperature of 600 °C. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission microscopy (HRTEM). Nitrogen adsorption-desorption was used for surface area (Brunauer-Emmett-Teller—BET) and porosity determination. The photoactivity of the prepared TiO₂/ZnO samples was assessed by the photocatalytic decomposition of Orange II dye in an aqueous slurry under irradiation of 254 and 365 nm wavelengths. Under the same conditions, the photocatalytic activity of a commercially available photocatalyst (Degussa P25), the pure anatase TiO₂ nanoparticles and cubic ZnO were examined.     

IR and XPS investigation of visible-light photocatalysis—Nitrogen-carbon-doped TiO2 film

To use solar irradiation or interior lighting efficiently, we sought a photocatalyst with high reactivity under visible light. Nitrogen and carbon doping TiO_2−x−yN_xC_y films were obtained by heating the TiO₂ gel in an ionized N₂ gas and then were calcined at 500 °C. The TiO_2−x−yN_xC_y films have revealed an improvement over the TiO₂ films under visible light (wavelength, 500 nm) in optical absorption and photocatalytic activity such as photodegradation of methyl orange. X-ray photoemission spectroscopy, infrared spectrum and UV-visible (UV-vis) spectroscopy were used to find the difference of two kinds of films. Nitrogen and carbon doped into substitutional sites of TiO₂ has been proven to be indispensable for band-gap narrowing and photocatalytic activity.     

Preparation, characterization of Au (or Pt)-loaded titania nanotubes and their photocatalytic activities for degradation of methyl orange

TiO₂ nanotubes were prepared by hydrothermal method and Au (or Pt) was loaded on TiO₂ nanotubes by photodeposition method. The photocatalysts were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption technique, respectively. The photocatalytic properties of the samples were also investigated. The results show that TiO₂ nanotubes with uniform diameter were prepared, and they have specific surface areas over 400 m²/g. The specific surface areas of TiO₂ nanotubes decrease with the increasing of calcining temperature, and crystalline phase of TiO₂ in the wall of nanotubes was transformed from anatase into rutile phase in calcination process. The photocatalytic activities of TiO₂ nanotubes are higher than that of nanosized TiO₂, and the photocatalytic activities of TiO₂ nanotubes were enhanced after loading Au (or Pt). After irradiation for 40 min under a 300 W of middle-pressure mercury lamp (MPML), the degradation rate of methyl orange solution using the Au/TiNT-500 (or Pt/TiNT-500) as a catalyst can reach 96.1% (or 95.1%). On the other hand, Au-loaded sample has evident adsorption peak in visible range, indicating that Au-loaded TiO₂ nanotubes are hopeful to become visible light photocatalyst.     

Synthesis and characterization of the Pd/InVO4-TiO2 co-doped thin films with visible light photocatalytic activities

Novel Pd/InVO₄-TiO₂ thin films with visible light photocatalytic activity were synthesized from the Pd and InVO₂ co-doped TiO₂ sol via sol-gel method. The photocatalytic activities of Pd/InVO₄-TiO₂ thin films were investigated based on the oxidative decomposition of methyl orange in aqueous solution. The as-prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy (UV-vis). The results indicate that the Pd/InVO₄-TiO₂ thin films are compact, uniform and consist of sphere nanoparticles with diameters about 80-100 nm. The UV-vis spectra show that the Pd/InVO₄-TiO₂ thin films extend the light absorption spectrum toward the visible region. XPS results reveal that doped Pd exist in the form of metallic palladium. The photocatalytic experiments demonstrate that Pd doping can effectively enhance the photocatalytic activities of InVO₄-TiO₂ thin films in decomposition of aqueous methyl orange under visible light irradiation. It has been confirmed that Pd/InVO₄-TiO₂ thin films could be excited by visible light (E < 3.2 eV) due to the existence of the Pd and InVO₄ doped in the films.     

Preparation and characterization of visible light responsive Fe2O3-TiO2 composites

In this study we present the effects of iron oxide (Fe₂O₃) on titanium dioxide (TiO₂) in synthesising visible-light reactive photocatalysts. A Fe₂O₃-TiO₂ composite photocatalyst was synthesized from Fe₂(SO₄)₃ and Ti(SO₄)₂ by a ethanol-assisted hydrothermal method. The preparation conditions were optimized through the investigation of the effects of hydrothermal temperature and time as well as molar ratio of Ti to Fe on the photocatalytic activity. The visual, physical and chemical properties of the Fe₂O₃-TiO₂ composites were investigated. The results showed that α-Fe₂O₃ and anatase TiO₂ were present in the composites. The Fe₂O₃-TiO₂ synthesized under optimum condition consisted of mesoporous structure with an average pore size of 4 nm and a surface area of 43 m²/g. Under visible and solar light irradiation, the photocatalytic activity of optimized sample was significantly higher than that of pure TiO₂. This sample led to a photodegradation efficiency of 90% and 40% of auramine under visible light and solar light, respectively.     

Gallium- and iodine-co-doped titanium dioxide for photocatalytic degradation of 2-chlorophenol in aqueous solution: Role of gallium

Visible-light-driven TiO₂-based catalysts for the degradation of pollutants have become the focus of attention. In the present work, iodine-doped titania photocatalysts (I-TiO₂) were improved by doping with gallium (Ga,I-TiO₂) and the resulting physicochemical properties and photocatalytic activity were investigated. The structural properties of the catalysts were determined by X-ray diffraction, UV-vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, Brunauer-Emmett-Teller analysis and transmission electron microscopy. We found that Ga probably enters the TiO₂ framework for doping levels <0.5 mol%. A further increase in Ga content probably leads to dispersal of excess Ga on the TiO₂ surface. The photocatalytic activity of Ga,I-TiO₂ catalysts was evaluated using 2-chlorophenol (2-CP) as a model compound under visible and UV-vis light irradiation. The results indicate that 0.5 mol% Ga loading and calcination at 400 °C represent optimal conditions in the calcining temperature range 400-600 °C and with doping levels from 0.1% to 1 mol%. The effective enhancement of 2-CP degradation might be attributed to the formation of oxygen vacancies by Ga doping, which could decrease the recombination of electron-hole pairs.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Synthesis, characterization and degradation of Bisphenol A using Pr, N co-doped TiO2 with highly visible light activity

Praseodymium and nitrogen co-doped titania (Pr/N-TiO₂) photocatalysts, which could degrade Bisphenol A (BPA) under visible light irradiation, were prepared by the modified sol-gel process. Tetrabutyl titanate, urea and praseodymium nitrate were used as the sources of titanium, nitrogen and praseodymium, respectively. The resulting materials were investigated by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), UV-vis absorbance spectroscopy, X-ray photoelectron spectroscopy (XPS), N₂ adsorption-desorption isotherm and Fourier transform infrared spectra (FTIR). It was found that Pr doping inhibited the growth of crystalline size and the transformation from anatase to rutile. The degradation of BPA under visible light illumination was taken as probe reaction to evaluate the photo-activity of the co-doped photocatalyst. In our experiments, the optimal dopant amount of Pr was 1.2 mol% and the calcination temperature was 500 °C for the best photocatalytic activity. Pr/N-TiO₂ samples exhibited enhanced visible-light photocatalytic activity compared to N-TiO₂, undoped TiO₂ and commercial P25. The nitrogen atoms were incorporated into the crystal of titania and could narrow the band gap energy. Pr doping could slow the radiative recombination of photogenerated electrons and holes in TiO₂. The improvement of photocatalytic activity was ascribed to the synergistic effects of nitrogen and Pr co-doping.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Study on the photocatalytic activity of TiN/TiO2 nanoparticle formed by ball milling

TiN/TiO₂ nanoparticle photocatalyst was prepared by ball milling of TiO₂ in H₂O solution doped with TiN. The photocatalyst was characterized by UV–Vis diffuse reflection spectroscopy, X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Based on the results of the characterization, the mechanism of the increase in photocatalytic activity was investigated. The results show that when the amount of doped TiN is 0.15 wt%, the photocatalytic activity of the TiN/TiO₂ is at its peak. Compared with TiO₂, the photoabsorption wavelength range of the TiN/TiO₂ photocatalyst red-shifts about 30 nm, and the photoabsorption intensity increases as well. The photocatalytic activities of the photocatalyst are higher than that of TiO₂ under UV and visible light irradiation. The increase of surface Ti³⁺ reactive center and the extension of the photoabsorption wavelength are the main factors for the increase in the photocatalytic activity of the TiN/TiO₂. Doped TiN neither changes the TiO₂ crystal phase nor creates new crystal phase by ball milling.     

Preparation and performance of photocatalytic TiO2 immobilized on palladium-doped carbon fibers

Pd-modified carbon fibers (CFs) are obtained by a facile oxidation-reduction method and then dip-coated in a sol-gel of titanium dioxide (TiO₂) to form supported TiO₂/Pd-CF photocatalysts. The morphology of the Pd-modified CFs and the amount Pd deposited are characterized by field emission scanning electron microscopy and atomic absorption spectrometry, respectively. X-ray diffraction is used to investigate the crystal structures of the TiO₂ photocatalyst. Acid orange II is used as a model contaminant to evaluate the photocatalytic properties of the photocatalyst under UV irradiation. TiO₂/Pd-CF exhibits higher catalytic activity than TiO₂/CF towards the degradation of acid orange II. Optimum photocatalytic performance and support properties are achieved when the Pd particle loading is about 10.8 mg/g.