Improvement of photocatalytic behavior of chemical-vapor-synthesized TiO2 nanopowders by post-heat treatment

Anatase-type TiO₂ nanopowders less than 10 nm in average diameter were synthesized by a chemical vapor synthesis method. The TiO₂ nanopowders showed very poor photocatalytic properties, in spite of their large surface area. With subsequent heat treatment of the TiO₂ powders, their photocatalytic properties determined by measuring the degradation of 2-propanol were improved at temperatures up to 600 °C and then diminished along with formation of a rutile phase. This improvement in the photocatalytic properties of TiO₂ nanopowders was attributed to both a morphology change and a change in the electronic surface characteristics of TiO₂ particles during heat treatment.     

First-principles study on anatase TiO2 codoped with nitrogen and praseodymium

The crystal structures, electronic structures and optical properties of nitrogen or/and praseodymium doped anatase TiO₂ were calculated by first principles with the plane-wave ultrasoft pseudopotential method based on density functional theory. Highly efficient visible-light-induced nitrogen or/and praseodymium doped anatase TiO₂ nanocrystal photocatalyst were synthesized by a microwave chemical method. The calculated results show that the photocatalytic activity of TiO₂ can be enhanced by N doping or Pr doping, and can be further enhanced by N+Pr codoping. The band gap change of the codoping TiO₂ is more obvious than that of the single ion doping, which results in the red shift of the optical absorption edges. The results are of great significance for the understanding and further development of visible-light response high activity modified TiO₂ photocatalyst. The photocatalytic activity of the samples for methyl blue degradation was investigated under the irradiation of fluorescent light. The experimental results show that the codoping TiO₂ photocatalytic activity is obviously higher than that of the single ion doping. The experimental results accord with the calculated results.     

Surface modification of nanocrystalline anatase with CTAB in the acidic condition and its effects on photocatalytic activity and preferential growth of TiO2

The nanocrystalline anatase TiO₂, which was synthesized by a sol-hydrothermal process in advance, has successfully modified with cetyltrimethylammonium bromide (CTAB) in the acidic condition as well as in the basic condition. On the basis of the measurements of infrared spectrum and X-ray photoelectron spectroscopy of the resulting TiO₂, together with the phase-transfer experiments, it is suggested that the modification mechanism in the acidic condition is closely related to Br⁻. Interestingly, compared with un-modified TiO₂, the modified TiO₂ exhibits high photocatalytic activity for degrading Rhodamine B (RhB) solution, especially for that modified in the acid. The enhanced photocatalytic activity of modified TiO₂ in the acid is attributed to the role that the Br⁻ can easily capture photo-induced holes and then form active Br, consequently effectively inducing photocatalytic oxidation reactions, based on the surface photovoltage responses of the resulting TiO₂. After that, a one-pot sol-hydrothermal route at the temperature as low as 80 °C is developed to directly synthesize CTAB-modified nanocrystalline TiO₂ with a little preferred growth along 〈0 0 1〉 direction, which can be easily dispersed in the organic system and possess good photocatalytic performance. This work provides a feasible strategy to further improve the photocatalytic performance of nanocrystalline anatase and to synthesize TiO₂ nanocrystals with preferential growth.     

A novel approach towards high-performance composite photocatalyst of TiO2 deposited on activated carbon

TiO₂ photocatalysts deposited on activated carbon (TiO₂/AC) were prepared by dip-hydrothermal method at 180 °C using peroxotitanate as a precursor, then calcinated at 300-800 °C. The samples were characterized by X-ray diffraction, scanning electron microscopy, Raman spectroscopy and the nitrogen absorption. Their photocatalytic activity was evaluated by degradation of methyl orange (MO). The results showed that TiO₂ particles of anatase type were well deposited on the activated carbon surface. TiO₂/AC calcinated at 600 °C exhibited the best photocatalytic performance. For the comparison, the same photocatalysis experiment was carried out for two mixtures of commercial TiO₂ (Degussa P25) with AC and synthetic TiO₂ with AC. It was found that the composite catalyst TiO₂/AC was better than the two mixtures. Besides, different from fine powdered TiO₂, the granular TiO₂/AC photocatalysts could be easily separated from the bulk solution and reused; indeed, its photocatalytic ability was hardly decreased after a five-cycle for MO degradation. The kinetics of the MO degradation fitted well the Langmuir-Hinshelwood model.     

Study on the photocatalytic activity of TiN/TiO2 nanoparticle formed by ball milling

TiN/TiO₂ nanoparticle photocatalyst was prepared by ball milling of TiO₂ in H₂O solution doped with TiN. The photocatalyst was characterized by UV–Vis diffuse reflection spectroscopy, X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Based on the results of the characterization, the mechanism of the increase in photocatalytic activity was investigated. The results show that when the amount of doped TiN is 0.15 wt%, the photocatalytic activity of the TiN/TiO₂ is at its peak. Compared with TiO₂, the photoabsorption wavelength range of the TiN/TiO₂ photocatalyst red-shifts about 30 nm, and the photoabsorption intensity increases as well. The photocatalytic activities of the photocatalyst are higher than that of TiO₂ under UV and visible light irradiation. The increase of surface Ti³⁺ reactive center and the extension of the photoabsorption wavelength are the main factors for the increase in the photocatalytic activity of the TiN/TiO₂. Doped TiN neither changes the TiO₂ crystal phase nor creates new crystal phase by ball milling.     

Preparation of visible light responsive N doped TiO2 via a reduction-nitridation procedure by nonthermal plasma treatment

A visible light responsive N-doped TiO₂ was prepared via a reduction-nitridation procedure by nonthermal plasma treatment. X-ray diffraction, N₂ adsorption, UV-vis spectroscopy, photoluminescence, and X-ray photoelectron spectroscopy were used to characterize the prepared TiO₂ samples. The plasma treatment did not change the phase composition and particle sizes of TiO₂ samples, but extended its absorption edges to the visible light region. The photocatalytic activities were tested in the degradation of an aqueous solution of a reactive dyestuff, methylene blue, under visible light. The photocatalytic activities of TiO₂ prepared by reduction-nitridation procedure were much higher than that of samples prepared by simple nitridation treatment. The enhanced activity was ascribed to the substitutional N-doping and appropriate concentration of oxygen vacancies. TOHN10 prepared by reduction-nitridation procedure exhibited excellent photocatalytic stability. A possible mechanism for the photocatalysis was proposed.     

Reasons for the deactivation of Pt/TiO2 photocatalyst treated by inert gas N2

The effect of N₂ treatment on the photocatalytic activity of Pt⁰/TiO₂ was investigated. The results showed that after treatment at 500 °C in N₂, 70% of the photocatalytic activity of 1.0 wt.% Pt⁰/TiO₂ was lost by the evaluation of photocatalytic oxidation reaction of C₃H₆. Transmission electron microscopy (TEM) and Ar⁺ ion sputtering tests revealed that in the course of high-temperature N₂ treatment, the size of Pt⁰ particles on TiO₂ increases and a strong interaction between metal and support, i.e. Pt⁰ particles encapsulated by Ti_xO_y, happens, which are the reasons for the deactivation of Pt⁰/TiO₂ photocatalyst treated by high-temperature N₂.     

Preparation of nanosized crystalline TiO2 particles at low temperature for photocatalysis

Nanocrystalline titanium dioxide (TiO₂) particles were prepared by a modified alkoxide method under acidic conditions at temperatures ranging from 60°C to 90°C. The reaction temperature was used to control the crystalline phase of the TiO₂ particles. At 60°C and 75°C rutile was formed whilst at 90°C anatase and brookite were formed.The photocatalytic activity of the prepared particles was tested for the degradation of sucrose. The photocatalytic activities of the prepared nanosized TiO₂ were compared to those obtained from Degussa P-25 TiO₂ as well as TiO₂ crystalline samples prepared using the conventional sol–gel/heat treatment method. At low organic concentrations, Degussa P-25 exhibited higher photocatalytic behaviour than all the prepared particles while, at high organic concentrations, the nanosized TiO₂ particles prepared at low temperature displayed an activity comparable to Degussa P-25 but much higher than the heat treated sample. The formation of excess intermediates during the degradation of higher sucrose loadings is believed to hinder the photoactivity of Degussa P-25, while the prepared TiO₂ particles are able to maintain their activity for the degradation of the intermediates of sucrose.     

Influence of deposition atmosphere on photocatalytic activity of TiO2/SiOx double-layers prepared by RF magnetron sputtering

TiO₂/SiO_x double-layers have been prepared at room temperature by RF magnetron sputtering. The TiO₂ top-layer was deposited in an Ar atmosphere, while the SiO_x bottom-layer was deposited in an Ar/O₂ atmosphere. Samples were characterized using X-ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy, and photoluminescence techniques. The photocatalytic activity of the samples was evaluated by the photodegradation of methylene blue; the results showed that the photocatalytic activity of the TiO₂/SiO_x double-layers was superior to that of the TiO₂ single-layers. The presence of the SiO_x bottom-layer improved the photocatalytic activity of the TiO₂ layer because it may act as a trap for electrons generated in the TiO₂ layer thus preventing electron-hole recombinations.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Effect of structure on the photocatalytic activity of Pt-doped TiO2 nanotubes

Highly ordered TiO₂ nanotubes with different tube length were fabricated by anodization using C₂H₂O₄·2H₂O containing 0.5 wt.% NH₄F (electrolyte A) and anhydrous dimethyl sulfoxide containing 1% HF (electrolyte B), respectively. Then cathodic reduction method was used to dope Pt in TiO₂ nanotubes in chloroplatinic acid. The results indicated that cathodic reduction could efficiently platinize TiO₂ nanotubes. Pt-doped TiO₂ nanotubes with the longer length had the higher photocatalytic activity for degrading methyl orange under UV and visible irradiation. The longer tube length has a positive effect on the photocatalytic activity of Pt-doped TiO₂ nanotubes. Besides, as the content of anatase further decreases, the photocatalytic activity drops gradually due to the reduction reaction in the surface area.     

One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Structural transformation study of TiO2 nanoparticles annealing at different temperatures and the photodegradation process of eosin-Y

Hydrothermal method was used to prepare TiO₂ nanoparticles with annealing temperature at 500 °C–700 °C. The mixture of anatase-rutile phase was investigated by powerful tool of X-ray diffraction (XRD). The structural parameters of anatase and rutile mixture phaseTiO₂ nanoparticles were calculated from the Rietveld refinement. The transformation rate of rutile was increased linearly with an annealing temperature of 500 °C–700 °C. The spherical morphology of the anatase and rutile mixed phase were obtained by scanning electron microscope and transmission electron microscope. The spherical particle of the anatase and rutile TiO₂ shows with great aggregation with different size and within the range of few tens nm. The EDAX study revealed the presence of titanium and oxygen. The best photocatalytic activity was identified as the 87.04% of anatase and 12.96% of rutile mixer phase of TiO₂. Various factors could be involved for a better photocatalytic activity.     

Influence of the OH groups on the photocatalytic activity and photoinduced hydrophilicity of microwave assisted sol-gel TiO2 film

In the present work the influence of the OH groups on the photocatalytic activity and the photoinduced hydrophilicity of microwave assisted sol-gel TiO₂ films was investigated. The prepared TiO₂ films were characterized using XRD and AFM. Furthermore, the surface of the TiO₂ films was examined by help of XPS in order to determine the amount of OH groups before and after UV irradiation at different humidities. The activity of the TiO₂ films was determined using stearic acid as a model compound and the photoinduced superhydrophilicity was investigated through contact angle measurements.The results of this investigation showed that the microwave assisted sol-gel technique produces highly homogeneous and efficient TiO₂ films without the need for heat treatment for crystallization. Based on the conducted experiments it is suggested that the amount of OH groups on the TiO₂ surface highly influence the photocatalytic activity and the photoinduced superhydrophilicity and that the two mechanisms may be closely related. It is suggested that the superhydrophilicity is obtained through a combination of photocatalytic degradation of organic contaminants and surface structural changes in form of an increased amount of OH-groups.     

Structural, photochemical and photocatalytic properties of zirconium oxide doped TiO2 nanocrystallites

Composite photocatalysts composed of TiO₂ and ZrO₂ have been prepared via the sol-gel method. The as-prepared nanocomposites are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis spectrometry and fluorescence emission spectra. The results shows that TiO₂/ZrO₂ nanocomposites are composed of mainly anatase titania and tetragonal ZrO₂. Incorporating TiO₂ particles with ZrO₂ plays an important role in promoting the formation of nanoparticles with an anatase structure and leads to decreased fluorescence emission intensity. Most of the TiO₂/ZrO₂ nanocomposites exhibited comparable photocatalytic activity compared with commercial TiO₂ for the degradation aqueous methyl orange (MO) under ultraviolet irradiation, while the composite with Zr/Ti mass ratio of 15.2% shows the highest photocatalytic performances. Furthermore, the as-prepared nanocomposites can be reused with little photocatalytic activity loss. Without any further treatment besides rinsing, the photocatalytic activity of TiO₂/ZrO₂ (15.2%) composites is still higher than after five-cycle utilization.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Enhanced photocatalytic degradation of Safranin-O by heterogeneous nanoparticles for environmental applications

Nanostructure titanium dioxide (TiO₂) has been synthesized by hydrolysis of titanium tetrachloride in aqueous solution and Ag-TiO₂ nanoparticles were synthesized by photoreduction method. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier-transform infrared (FT-IR) and UV-vis absorption spectroscopy. The experimental results showed that the sizes of the synthesized TiO₂ and Ag-TiO₂ particles are in the range of 1.9-3.2 nm and 2-10 nm, respectively. Moreover, Ag-TiO₂ nanoparticles exhibit enhanced photocatalytic activity on photodegradation of Safranin-O (SO) dye as compared to pure TiO₂. The positive effect of silver on the photocatalytic activity of TiO₂ may be explained by its ability to trap electrons. This process reduces the recombination of light generated electron-hole pairs at TiO₂ surface and therefore enhances the photocatalytic activity of the synthesized TiO₂ nanoparticles. The effects of initial dye and nanoparticle concentrations on the photocatalytic activity have been studied and the results demonstrate that the dye photodegradation follows pseudo-first-order kinetics. The observed maximum degradation efficiency of SO is about 60% for TiO₂ and 96% for Ag-TiO₂.     

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

TiO₂ nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO₂ nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO₂ nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO₂ mass weight, respectively, and the linkage between DBS groups and TiO₂ surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO₂ obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO₂ is also related to the increase in the capability for adsorbing RhB.     

Photocatalytic behavior of heavy La-doped TiO2 films deposited by pulsed laser deposition using non-sintered target

We have investigated the control of photocatalytic behavior under deposited conditions of non-sintered target of different molar ratios with TiO₂ and La₂O₃ from 1:0 to 1:2 for heavily La doping, and post-annealing temperature from 600 °C to 1000 °C for crystallizing by pulsed laser deposition. We have successfully crystallized heavily La-doped TiO₂ films with post-annealing temperature over 800 °C and with molar ratio of TiO₂:La₂O₃ over 1:1 on a quartz substrate. Heavily La-doped TiO₂ films are observed the decomposition of methylene blue and a water-splitting reaction in photocatalytic behavior under Xe light irradiation. When stoichiometric La-doped TiO₂ (TiO₂:La₂O₃ = 1: 1) is synthesized with heat-treatment at 900 °C, the best results are obtained under photocatalytic behavior and pure La₂Ti₂O₇ crystalline were obtained.     

Efficient visible-light-induced photocatalytic degradation of MO on the Cr-nanocrystalline titania-S

In order to improve visible light photocatalytic activities of the nanometer TiO₂, a novel and efficient Cr,S-codoped TiO₂ (Cr-TiO₂-S) photocatalyst was prepared by precipitation-doping method. The crystalline structure, morphology, particle size, and chemical structure of Cr-TiO₂-S were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and Fourier transform infrared (FT-IR) techniques, respectively. Results indicate that the doping of Cr and S, cause absorption edge shifts to the visible light region (λ > 420 nm) compare to the pure TiO₂, reduces average size of the TiO₂ crystallites, enhances desired lattice distortion of Ti, promotes separation of photo-induced electron and hole pair, and thus improves pollutant decomposition under visible light irradiation. The photocatalytic activities of Cr-TiO₂-S nanoparticles were evaluated using the photodegradation of methyl orange (MO) as probe reaction under the irradiation of UV and visible light and it was observed that the Cr-TiO₂-S photocatalyst shows higher visible photocatalytic activity than the pure TiO₂. The optimal Cr-TiO₂-S concentration to obtain the highest photocatalytic activity was 5 mol% for both of Cr and S.