尖晶石铁氧体TixNi1-xFe2O4中阳离子分布和Ti离子磁矩的实验研究

采用固相反应法制备了系列样品Ti_xNi_1-xFe₂O₄ (x=0.0, 0.1, 0.2, 0.3, 0.4). 室温下的X射线衍射谱表明样品全部为(A)[B]₂O₄型单相立方尖晶石结构, 属于空间群Fd3m. 样品的晶格常数随Ti掺杂量的增加而增大. 样品在10 K温度下的比饱和磁化强度σ_S随着Ti掺杂量x的增加逐渐减小. 研究发现, 当Ti掺杂量x≥ 0.2时, 磁化强度σ随温度T的变化曲线出现两个转变温度T_L和T_N. 当温度低于T_N时, 磁化强度明显减小; 当温度达到T_N时, dσ/dT具有最大值. σ-T曲线的这些特征表明, 由于Ti掺杂在样品中出现了附加的反铁磁结构. 这说明样品中的Ti离子不是无磁性的+4价离子, 而是以+2和+3价态存在, 其离子磁矩的方向与Fe和Ni离子的磁矩方向相反. 利用本课题组提出的量子力学方势垒模型拟合样品在10 K温度下的磁矩, 得到了Ti, Fe和Ni三种阳离子在(A)位和[B]位的分布情况, 并发现在所有掺杂样品中, 80%的Ti离子以+2价态占据尖晶石结构的[B]位.     

缺氧条件下准一维自旋梯状结构化合物(Sr1-xCax)14Cu24O41-δ的磁化率特性研究

在空气环境中采用固相反应方法制备出三种A位Ca掺杂自旋梯状结构化合物(Sr_1-xCa_x)₁₄Cu₂₄O_41-δ样品(x＝0,0.25,0.43)能量损失谱(EDS)分析表明,该体系Ca掺杂样品均严重缺氧(分别对应的缺氧含量δ＝7.64,6.99,6.67).X射线衍射(XRD)结果显示,所有样品均为单相,并且晶格常数a,b,c的值随着缺氧含量δ的增加而增大.1T直流磁场下的磁化率-温度曲线及其拟合结果表明,对无Ca掺杂样品Sr₁₄Cu₂₄O_41-δ(δ＝7.64),氧含量减少导致自旋链上空穴数的减少,自旋链上自由自旋的Cu离子数目增大,而参与二聚化的Cu离子数目略有减小;而对Ca掺杂样品(Sr_1-xCa_x)₁₄Cu₂₄O_41-δ,随着Ca含量的增加,样品中氧缺失量降低,但Ca掺杂引起空穴减少的程度更强. 关键词： 自旋梯状结构化合物 氧缺位 晶体结构 磁化率     

稀土硼化物LaxCe1-xB6亚微米粉的制备及光吸收研究

以稀土氧化物La₂O₃和CeO₂为稀土源, 以NaBH₄为硼源在真空环境中通过固相反应成功制备出了分散性好的单相三元La_xCe_1-xB₆亚微米粉. 系统研究了掺杂元素La对CeB₆物相, 微观结构及光吸收性能的影响. 实验结果表明, La元素的掺杂没有改变CeB₆的物相和晶体结构, 而是无序替代了Ce原子晶位. 光吸收结果表明, 随着La掺杂量的增加La_xCe_1-xB₆分散液吸收谷波长从620 nm减小到610 nm出现了蓝移现象.     

Co1-xNixSb3-ySey热电输运中晶界和点缺陷的耦合散射效应

结合机械合金化与放电等离子烧结工艺制备了Ni和Se共掺的细晶方钴矿化合物Co_1-xNi_xSb_3-ySe_y,研究了晶界和点缺陷的耦合散射效应对CoSb₃热电输运特性的影响.通过Ni掺杂优化载流子浓度提高功率因子.在x=0.1时,功率因子达到最大值1750μWm^-1K^-2(450℃),是没有掺Ni试样的两倍.晶界和点缺陷的耦合散射机理使晶格热导率急剧下降,其中Co_0.9Ni_0.1Sb_2.85Se_0.15的室温晶格热导率降低至1.67Wm^-1K^-1,接近目前单填充效应所能达到的最低值1.6Wm^-1K^-1,其热电优值ZT在450℃时达到最大值0.53.将Callaway-Von Baeyer点缺陷散射模型嵌入到Nan-Birringer有效介质理论模型,对晶界散射和点缺陷散射的耦合效应对热导率的影响进行了定量分析,模型计算与实验结果符合.理论模型计算表明,当晶粒尺寸下降到50nm同时掺杂引入点缺陷散射后,Co_0.9Ni_0.1Sb_2.85Se_0.15的晶格热导率下降到0.8Wm^-1K^-1. 关键词： 3')" href="#">CoSb₃ Ni和Se掺杂 热电性能 耦合散射效应     

Ba1-xSrxTiO3及Ba0.6-xPbxSr0.4TiO3陶瓷的制备和介温特性研究

用固相反应法制备了Ba_1-xSr_xTiO₃(BST)及Ba_0.6-xPb_xSr_0.4TiO₃(BPST)陶瓷,通过XRD,FESEM和拉曼谱分析了Pb掺杂对Ba_0.6Sr_0.4TiO₃样品的晶格、相变及表面形貌的影响.测试了BST及B 关键词： BST BPST 弥散相 介温特性     

In0.3Co4Sb12-xSex 方钴矿热电材料的制备和热电性能

用熔融退火结合放电等离子烧结法制备了In_0.3Co₄Sb_12-xSe_x(x=0—0.3)方钴矿热电材料,探讨了In的存在形式,系统研究了Se掺杂量对结构和热电性能的影响.结果表明:In可以填充到方钴矿二十面体空洞处,过量In在晶界处形成InSb第二相,Se对Sb的置换使晶格常数减小,In填充上限降低;In_0.3Co₄Sb_12-xSe_x样品呈n型传导,随着Se掺杂量的增大,载流子浓度降低,电导率下降,Seebeck系数增大,功率因子有所降低;由于在结构中引入了质量波动及晶格畸变,适量的Se掺杂可以大幅降低材料晶格热导率;样品In_0.3Co₄Sb₁₂和In_0.3Co₄Sb_11.95Se_0.05的最大ZT值均达到1.0以上. 关键词： 掺杂 填充式方钴矿 热电性能     

钙钛矿锰氧化物(La1-xGdx)4/3Sr5/3Mn2O7 (x=0, 0.025) 磁性和输运性质研究

采用传统的高温固相烧结法制备了双层钙钛矿锰氧化物(La_1-xGd_x)_4/3Sr_5/3Mn₂ O₇ (x=0, 0.025)多晶样品. 通过X射线衍射仪研究发现样品为Sr₃Ti₂O₇型四方结构, 空间群为I4/mmm; 磁性测量表明, Gd³⁺掺杂后的样品(La_0.975Gd_0.025)_4/3Sr_5/3Mn₂O₇的三维磁有序转变温度(T_C1^3D)、磁化强度(M)均降低, 这是由于Gd³⁺的掺杂引起晶格的畸变, 从而使得晶格常数发生改变, 减弱了铁磁耦合而导致的; 通过电子自旋共振谱测量发现, 在T_C^3D<T<300 K温度范围内, 两样品在顺磁的基体上均有短程的铁磁团簇存在, 出现了相分离现象. 电性测量表明: 两样品分别在T_C1^3D (La_4/3Sr_5/3Mn₂O₇ 样品的三维磁有序转变温度, T_C0^3D)<T<300 K温度范围内均以三维变程跳跃的方式导电, 分析得出Gd³⁺的掺杂使得载流子局域长度的减小. 这表明载流子需要吸收更多的能量才能克服晶格的束缚进行跳跃, 因此(La_0.975Gd_0.025)_4/3Sr_5/3Mn₂ O₇ 样品的电阻较高.     

MnxSi1-x磁性薄膜的结构研究

利用X射线衍射(XRD)和X射线吸收近边结构(XANES)方法研究了在Si(100)衬底上及600℃温度条件下用分子束外延(MBE)共蒸发方法生长的Mn_xSi_1-x磁性薄膜的结构.由XRD结果表明,只有在高Mn含量(8％和17％)样品中存在着Mn₄Si₇化合物物相.而XANES结果则显示,对于Mn浓度在0.7%到17%之间的Mn_xSi_1-x样品,其Mn原子的XANES谱表现出了一致的谱线特征.基于多重散射的XANES理论计算进一步表明,只有根据Mn₄Si₇模型计算出的理论XANES谱才能够很好的重构出Mn_xSi_1-x样品的实验XANES谱.这些研究结果说明在Mn_xSi_1-x样品中,Mn原子主要是以镶嵌式的Mn₄Si₇化合物纳米晶颗粒存在于Si薄膜介质中,几乎不存在间隙位和替代位的Mn原子. 关键词： xSi_1-x磁性薄膜')" href="#">Mn_xSi_1-x磁性薄膜 分子束外延 XRD XANES     

(La0.7Sr0.3MnO3 )m(BiFeO3)n 超晶格结构的导电机理

利用射频磁控溅射的方法在SrTiO₃(001) 基片上制备了(La_0.7Sr_0.3MnO₃)_m(BiFeO₃)_n超晶格结构.对所制备的超晶格结构进行了50—150℃温度范围内的电流-电压测试分析.结果表明,随着BiFeO₃薄膜的厚度减小,温度的升高,(La_0.7Sr_0.3MnO₃)_m(BiFeO₃)_n超晶格结构的电流变大.进一步根据介质导电模型对(La_0.7Sr_0.3MnO₃)_m(BiFeO₃)_n超晶格结构的导电特性做了分析.在温度较低或者电场较弱时,所制备的(La_0.7Sr_0.3MnO₃)_m(BiFeO₃)_n超晶格结构表现为欧姆导电,而在高温,高电场的情况下,其导电行为由空间电荷限制电流机理主导. 关键词： 超晶格薄膜 多铁 空间电荷限制电流     

自旋梯状化合物Sr14(Cu1-yFey)24O41的拉曼散射谱研究

利用常规的固相合成法制备了三种Sr₁₄(Cu_1-yFe_y)₂₄O₄₁(y=0,0.03,0.05)多晶样品,其中y=0.03是单纯Fe³⁺掺杂,y=0.05是Fe³⁺和Fe²⁺混合掺杂.在100—1500cm^-1频移范围内测量了这三种样品的偏 关键词： 拉曼散射 电输运性质 自旋梯状化合物     

Epitaxial growth and transport properties of compressively-strained Ba2IrO4 films

Ba₂IrO₄ is a sister compound of the widely investigated Sr₂IrO₄ and has no IrO₆ octahedral rotation nor net canted antiferromagnetic moment, thus it acts as a system more similar to the high-T_c cuprate. In this work, we synthesize the Ba₂IrO₄ epitaxial films by reactive molecular beam epitaxy and study their crystalline structure and transport properties under biaxial compressive strain. High resolution scanning transmission electron microscopy and x-ray diffraction confirm the high quality of films with partial strain relaxation. Under compressive epitaxial strain, the Ba₂IrO₄ exhibits the strain-driven enhancement of the conductivity, consistent with the band gap narrowing and the stronger hybridization of Ir-t_2g and O-2p orbitals predicted in the first-principles calculations.     

正磷酸盐晶体Ba3(PO4)2和Sr3(PO4)2高温拉曼光谱研究

测量了碱土金属正磷酸盐Ba₃(PO₄)₂和Sr₃(PO₄)₂常温及高温拉曼光谱, 对拉曼振动模式进行指认, 并分析了晶体拉曼振动光谱及晶体结构在高温下的变化. 在温度升高的过程中, 拉曼振动频率向低频移动且振动峰宽度展宽, 晶体中的P-O平均键长随温度升高而变长, 但O-P-O的键角并未发生变化. 晶体在900 ℃以下无结构相变发生. 关键词： 3(PO₄)₂和Sr₃(PO₄)₂')" href="#">Ba₃(PO₄)₂和Sr₃(PO₄)₂ 高温拉曼光谱 振动模式 高温结构     

Crystal structure, superconductivity and magnetic properties of the superconducting ferromagnets Gd1.4−xDyxCe0.6Sr2RuCu2O10 (x=0–0.6)

The structural, electrical and magnetic properties of the superconducting ferromagnets, Gd_1.4−xDy_xCe_0.6Sr₂RuCu₂O₁₀ (x=0–0.6) are systematically investigated as a function of Dy doping and temperature. These compounds are characterized by high temperature superconductivity (T_c ranging from 20 to 40 K depending upon the Dy content) co-existing with weak ferromagnetism with two magnetic transitions (T_M2 ranging from 95 to 106 K and T_M1 around 120 K). Doping with Dy gives no significant structural changes except for a minor change in the c/a ratio. However the superconducting transition temperature is significantly suppressed and magnetic ordering temperature enhanced on Dy doping. These effects are described and discussed.     

K2NiF4型Sr2CrO4的磁电性质研究

以SrO和CrO₂为原料, 在高温高压的条件下直接反应生成纯相的K₂NiF₄结构的Sr₂CrO₄多晶样品. 结构用粉末X射线衍射及GSAS精修表征. 磁化率测试显示样品存在一个弱的反铁磁相变, 奈尔温度为T_N=95 K. 在奈尔温度以上, 磁化率随温度的变化遵循居里-外斯定律. 对样品进行了电阻测试, 结果显示了样品的绝缘特性.     

First-principles study of electronic structure and magnetic properties of Sr3Fe2O5 oxide

We investigate the electronic structure and magnetic properties of layered compound Sr₃Fe₂O₅ based on first-principles calculations in the framework of density functional theory with GGA+U method. Under high pressure, the ladder-type layered structure of Sr₃Fe₂O₅ is transformed into the infinite layered structure accompanied by a transition from G-type anti-ferromagnetic (AFM) insulator to ferromagnetic (FM) metal and a spin transition from S=2 to S=1. We reproduce these transformations in our calculations and give a clear physical interpretation.     

Doping effects in the Sr14Cu24O41-type structure: a Raman scattering study

Polarized micro-Raman spectra of different compounds belonging to the Sr₁₄Cu₂₄O₄₁-type structure were studied. In the spectra with parallel polarization along the plane crystal axes of the insulating samples Sr₉R₅Cu₂₄O₄₁ (R = La, Y) a broad peak near 3000 cm⁻¹, similar to the well-known two-magnon peak in the layered cuprates, was observed. In addition to the Raman lines characteristic for this structure, we observed only in the spectra with parallel to the chains numerous lines between 100 and 1200 cm⁻¹, probably originating from Raman-forbidden infrared-active only LO phonons and their combinations. In the spectra of the conducting compounds Sr_14−xCa_xCu₂₄O₄₁ (x = 0,7) these features were very weak or disappeared. We interpret these results as Raman evidence for hole doping of the Cu₂O₃ “spin-ladder” planes and for a redistribution of holes between chains and planes through Ca substitution in the case of the rare-earth-free samples.     

Observation of superconductivity (Tc = 50 K) in a new tetragonal alkaline-earth cuprate Sr0.8Ba1.2CuO3+δ, synthesised at ambient pressure

The ambient-pressure synthesis of a new tetragonal alkaline-earth superconducting cuprate, Sr_0.8Ba_1.2CuO_3+δ, from a cupro-oxycarbonate is reported. Magnetic-susceptibility measurements show the presence of a superconducting transition 50 K in a post-annealed sample. The crystal structure, refined from time-of-flight powder neutron-diffraction data was found to have an oxygen-deficient La₂CuO₄-type tetragonal T structure (a = 3.8988(3) Å and C = 12.815(3) Å) with oxygen vacancies located within the CuO₂ planes. Ordering of these oxygen vacancies is responsible for the observation of a superlattice in both neutron- and electron-diffraction measurements. An interpretation of the electron-diffraction patterns suggests that the superlattice in Sr_0.8Ba_1.2CuO_3+δ and also in the isostructural superconductor Sr₂CuO_3+δ are of an identical nature.     

Synthesis and superconducting properties of the infinite-layer compounds Sr1−xLnxCuO2(Ln=La, Nd, Sm, Gd)

Infinite-layer-type superconductors Sr_1−xLn_xCuO₂ are synthesized under high pressure of 3 GPa for Ln=Sm, Gd as well as for Ln=La, Nd. Their chemical and superconducting properties are systematically studied as functions of doping concentration and the kind of lanthanide ion. As a result, it is demonstrated that the variation of these properties with doping concentration is similar for all the examined Ln³⁺ ions. The solubility limit lies at x ≈ 0.10. CuO₂ sheets are expanded with increasing x, while their spacing decreases. The T_c onset determined by magnetic measurements remains constant for any doping concentration; only the Meissner fraction increases with increasing x.     

Effective activation energy Ue(T,J,H) in textured Bi1.84Pb0.4Sr2Ca2Cu3Oy silver-clamped thick films

We have measured the resistivity of textured Bi_1.84Pb_0.4Sr₂Ca₂Cu₃O_y silver-clamped thick films as a function of temperature, current density ranging from 10 to 1×10³ A/cm² and magnetic field up to 0.3 T. We find that the effective activation energy U_e follows U_e(T,J,H)=U₀(1−T/T_p)^mln(J_c0/J)H⁻ with m=1.75 for Hab-plane and 2.5 for Hc-axis and =0.76 for Hab and 0.97 for Hc, for the current density regime above 100 A/cm², where T_p is a function of applied magnetic field and current density. This result suggests the effective activation energy U_e be correlated with the temperature, current density and magnetic field. The possible dissipative mechanisms responsible for the temperature, current density and magnetic field dependence of the effective activation energy are discussed.