Measurement of UV absorption of single living cell for cell manipulation using NIR femtosecond laser

Optical UV absorption of single human living cells ranging from 200 nm to 360 nm was measured in situ for the study of cell manipulation using the near-infrared (NIR) femtosecond laser. Human breast living cells of MCF-10A, MCF-7, and MDA-MB-231 were used in this experiment. The selective photo-disruptions of single living cell and its sub-organelle (nucleus) were also demonstrated using the tightly focused 790 nm wavelength femtosecond laser with pulse duration of 110 fs. It was found that each living cell has its own absorption spectrum in UV wavelength ranges. It was also inferred that intrinsic absorption spectrum is attributed to the amount of DNA and protein of living cell. For the study of photo-disruption of single cell using the multi-photon absorption excited by the NIR femtosecond laser pulse, the origin UV absorption spectrum of targeted living cell is important and fundamental information to understand nonlinear interaction between NIR ultrashort, high-intensity laser light and transparent living cell.     

Raman study of phase transformation of TiO2 rutile single crystal irradiated by infrared femtosecond laser

Titanium dioxide (TiO₂) rutile single crystal was irradiated by infrared femtosecond (fs) laser pulses with repetition rate of 250 kHz and phase transformation of rutile TiO₂ was observed. Micro-Raman spectra show that the intensity of E_g Raman vibrating mode of rutile phase increases and that of A_1g Raman vibrating mode decreases apparently within the ablation crater after fs laser irradiation. With increasing of irradiation time, the Raman vibrating modes of anatase phase emerged. Rutile phase of TiO₂ single crystal is partly transformed into anatase phase. The anatase phase content transformed from rutile phase increased to a constant with increasing of fs pulse laser irradiation time. The study indicates the more stable rutile phase is transformed into anatase phase by the high pressure produced by fs pulse laser irradiation.     

Nonlinear absorption of CS2 at the wavelength of 400 nm with femtosecond pulses

Nonlinear absorption of carbon disulfide (CS₂) was investigated by Z-scan technique and time-resolved pump-probe technique with femtosecond pulses at 400 nm wavelength. By the two techniques, we confirmed that the nonlinear absorption of CS₂ arise from a combination of two-photon absorption (TPA) and the excited state absorption induced by TPA under the incident laser pulses with 400 nm wavelength. The coefficient of TPA, the absorption cross-section of low excited state and lifetime of low excited state were obtained by theoretical fitting the experimental results. The results indicated that the CS₂ has good optical limiting capability at 400 nm wavelength.     

The potential of UV femtosecond laser ablation for varnish removal in the restoration of painted works of art

Despite significant advances, laser ablation with nanosecond pulses presents limitations in dealing with the restoration of classes of painted works of art, such as paintings with a very thin layer of varnish. Femtosecond laser processing promises the means for overcoming such limitations. To this end, femtosecond ablation of two typical varnishes, dammar and mastic, is examined. For these varnishes, processing by Ti:Sapphire irradiation (800 nm) turns out to be ineffective. In contrast, irradiation with 248 nm ∼500 fs laser pulses results in a higher etching resolution (etching rates of ∼1 μm/pulse or less). For irradiation with few laser pulses at moderate laser fluences, etched morphology is far smoother than in the processing with nanosecond laser pulses. Furthermore, chemical modifications are considerably reduced (by nearly an order of magnitude), and exhibit a number of additional novel differences. Both etching rates and extent of chemical modifications are largely independent of varnish absorptivity. In all, femtosecond UV laser irradiation is indicated to hold a high potential, offering new perspectives for the restoration of painted works of art. Finally, a tentative model is advanced accounting in a consistent way for the observations.     

Femtosecond laser-induced fragmentation and cluster formation studies of solid phase trinitrotoluene using time-of-flight mass spectrometry

We use surface-femtosecond laser mass spectrometry to study the fragments/products formed when trinitrotoluene (TNT) is subjected to femtosecond laser pulse irradiation and to study the conditions under which TNT is removed from a solid surface. In surface-femtosecond laser mass spectrometry a compound is deposited on a solid substrate and is desorbed into vacuum by femtosecond irradiation forming a plume of ionized and neutral species. The positive or negative ions are then accelerated by an electric potential and allowed to drift in the field-free region of a time-of-flight mass spectrometer. The mass-to-charge ratio of each ion is obtained using the value of the accelerating field and the ion flight time. In this paper we report femtosecond laser mass spectra for the positive ions formed by desorbing TNT with 130 fs pulses centered at 800 nm for fluences ranging from 7 to 1.4 × 10⁵ J/m². The conditions under which TNT removal and ionization occur are also discussed.     

X-ray analysis of mechanical and thermal effects induced by femtosecond laser treatment of aluminum single crystals

Surface marking of aluminum single crystal is performed with femtosecond laser pulses. X-ray analysis allows to measure thermal and mechanical effects induced by the femtosecond laser pulses. These effects are estimated by comparing the pole figures (crystallinity) and the broadening of the diffraction peaks (mechanical contribution) before and after the laser irradiation. The results show that the femtosecond laser treatment ensures a re-crystallization of the structure and the presence of mechanical residual stresses. The analysis of the pole figures provides the sign of a re-crystallization on smaller volumes compared to initial ones. After the laser irradiation, the crystallization is perfectly oriented like the (1 1 0) orientation of the massive sample. Moreover, following the laser treatment, we show that the crystallographic structure is purer than the initial one. We also prove that the laser effect is persistent on a typical scale of 10 μm beyond the surface.     

Optical and ultrasonic monitoring of femtosecond laser filamentation in fused silica

Millimeter-long filaments and accompanying luminous plasma and defect channels created in fused silica (FS) by single focused femtosecond laser pulses with supercritical powers were probed in situ using optical imaging and contact ultrasonic techniques. Above the threshold pulse energy E_opt = 5 μJ corresponding to a few megawatt power levels pulses collapse due to self-focusing, producing channels filled by electron-hole plasma and luminescent defects, and exhibits predominantly compressive pressure transients. Analysis of the optical and ultrasonic response versus the laser pulse energy suggests that filamentary pulse propagation in the channels occurs with considerable dissipation of about ∼10 cm⁻¹. The predominant ionization mechanism is most likely associated with avalanche ionization, while the main mechanism of optical absorption is free-carrier absorption via inverse Bremsstrahlung interaction with the polar lattice.     

Femtosecond laser micromachining and biological therapy

Nonlinear micromachining with femtosecond laser pulses has attracted much attention in microphotonics and biophotonics. In this paper, we demonstrate the fabrication of optical elements in bulk transparent materials, direct welding between transparent substrates, and subcellular ablation in living cells by focusing femtosecond laser pulses.     

紧聚焦飞秒脉冲与石英玻璃相互作用过程中的电子动量弛豫时间研究

本文通过数值模拟(3+1)维扩展的广义非线性薛定谔方程,研究了紧聚焦飞秒激光脉冲在诱导石英玻璃的非线性电离过程中电子动量弛豫时间对于该电离过程的影响.计算结果证明电子动量弛豫时间会直接影响入射脉冲在焦点区域所形成的峰值场强、自由电子态密度和能流等参量的分布态势,因此在与实验结果相比较后发现适合于相互作用过程的电子动量弛豫时间的理论值约为1.27 fs.进一步的研究表明,电子动量弛豫时间与逆韧致吸收效应、雪崩电离的概率、等离子体密度、等离子体的自散焦效果以及间接引起的焦平面位置的移动都有着密切的联系.当前的研究结果表明电子动量弛豫时间在飞秒激光脉冲与物质相互作用的过程中发挥着重要作用.     

Realignment process of actin stress fibers in single living cells studied by focused femtosecond laser irradiation

Three-dimensional dissection of a single actin stress fiber in a living cell was performed based on multi-photon absorption of a focused femtosecond laser pulse. The realignment process of an actin stress fiber was investigated after its direct cutting by a single-shot femtosecond laser pulse irradiation by high-speed transmission and fluorescence imaging methods. It was confirmed that mechanical force led by the femtosecond laser cutting propagates to entire cell through the cytockelton in a 100 μs time scale. The cut actin stress fiber was realigned in the time scale of a few tens of minutes. The dynamic analysis of the realignment induced by single-shot femtosecond laser gives new information on cell activity.     

Nanofoaming in the surface of biopolymers by femtosecond pulsed laser irradiation

In this work, the nanostructuring induced in femtosecond (fs) laser irradiation of biopolymers is examined in self-standing films of collagen and gelatine. Irradiation by single 90 fs pulses at 800, 400 and 266 nm is shown to result in the formation of a modified layer with submicrometric size structures. The size and uniformity of the observed features are strongly dependent on irradiation wavelength and on the characteristics of the biopolymer (water content and mechanical strength). Examination of the films by laser induced fluorescence serves to assess the chemical modifications induced by laser irradiation, revealing changes in the emission bands assigned to the aromatic amino acid tyrosine and its degradation products. The results are discussed in the framework of a mechanism involving the generation of large free-electron densities, through multiphoton and avalanche ionization, which determine the temperature and stress distribution in the irradiated volume.     

Absorption and second harmonic emission from interaction of femtosecond laser pulses with microspherical droplets

In this paper, the interaction of femtosecond laser pulses with droplets microplasma at the intensity of 10¹⁶ W/cm² is theoretically studied. Laser absorption, suprathermal electron generation, and second harmonic generation are discussed. Using an analytical model and a 2D particle-in-cell code, we find that the dominated mechanism is resonant absorption in the interaction of femtosecond laser pulses with droplets for the misrospherical geometry.     

Two color laser ablation: Enhanced yield, improved machining

Laser ablation of semiconductors with nano- and picosecond lasers can be significantly improved, both in terms of yield and surface quality, by simultaneous irradiation of the sample with the fundamental beam (λ = 1064 nm) and a small amount of its second harmonic (SH) produced in a thin nonlinear crystal. While the total energy fluence is conserved, the small fraction of the second harmonic serves to excite electrons into the conduction band to get the ablation process started. For femtosecond laser pulses, the effect becomes insignificant, since sufficient conduction band population is provided by multiphoton absorption.     

Flexible gratings fabricated in polymeric plate using femtosecond laser irradiation

Flexible gratings embedded in poly-dimethlysiloxane (PDMS) were fabricated using femtosecond laser pulses. Photo-induced gratings in a flexible PDMS plate were directly written by a high-intensity femtosecond (130 fs) Ti: Sapphire laser (λ_p=800 nm). Refractive index modifications with 4 μm diameters were photo-induced after irradiation of the femtosecond pulses with peak intensities of more than 1×10¹¹ W/cm². The graded refractive index profile was fabricated to be symmetric around the center of the focal point. The diffraction efficiency of the grating samples is measured by an He-Ne laser. The maximum value of refractive index change (Δn) in the laser-modified regions was estimated to be approximately 3.17×10⁻³.     

Parametric study on femtosecond laser pulse ablation of Au films

Ablation process of 1 kHz rate femtosecond lasers (pulse duration 148 fs, wavelength 775 nm) with Au films on silica substrates has been systemically studied. The single-pulse threshold can be obtained directly. For the multiple pulses the ablation threshold varies with the number of pulses applied to the surface due to the incubation effect. From the plot of accumulated laser fluence N × ?_th(N) and the number of laser pulses N, incubation coefficient of Au film can be obtained (s = 0.765). As the pulse energy is increased, the single pulse ablation rate is increasing following two ablation logarithmic regimes, which can be explained by previous research.     

Femtosecond laser embedded grating micromachining of flexible PDMS plates

We report on the femtosecond laser micromachining of photo-induced embedded diffraction grating in flexible Poly (Dimethly Siloxane) (PDMS) plates using a high-intensity femtosecond (130 fs) Ti: sapphire laser (λ_p = 800 nm). The refractive index modifications with diameters ranging from 2 μm to 5 μm were photo-induced after the irradiation with peak intensities of more than 1 × 10¹¹ W/cm². The graded refractive index profile was fabricated to be a symmetric around from the center of the point at which femtosecond laser was focused. The maximum refractive index change (Δn) was estimated to be 2 × 10⁻³. By the X-Y-Z scanning of sample, the embedded diffraction grating in PDMS plate was fabricated successfully using a femtosecond laser.     

Direct fabrication of periodic patterns with hierarchical sub-wavelength structures on poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) thin films using femtosecond laser interference patterning

A simple optical interference method for the fabrication of simply periodic and periodic with a substructure on poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) using femtosecond laser interference patterns is demonstrated. The femtosecond laser pulse was split by a diffractive beam splitter and overlapped with two lenses. Homogeneous periodic arrays could be fabricated even using a single laser pulse. In addition, multipulse irradiation resulted in reproducible sub-wavelength ripples oriented perpendicularly to the laser polarization with spatial period from 170 to 220 nm (around one-fourth of the laser wavelength). In addition, the observed size of the spatial period was not affected by the number of incident laser pulses or accumulated energy density. Using high energy pulses it was possible to completely remove the PEDOT:PSS layer without inducing damage to the underneath substrate.     

Photophysical studies on axially substituted indium and gallium phthalocyanines upon UV-Vis laser irradiation

A series of results from different photophysical experiments on indium and gallium phthalocyanine (Pc) compounds is reported. Gallium Pc's have much longer singlet and triplet excited state lifetimes in comparison with indium Pc's. The strong reverse saturable absorption observed at 532 nm excitation is a consequence of the increase in absorbance of Pc's in the triplet excited state in the optical window comprised between Q- and B-bands, as verified upon laser irradiation with ns pulses at 355 nm. Using C₆₀ as a reference, the intersystem cross quantum yields of tBu₄PcInCl and tBu₄PcGaCl are 0.70 and 0.36, respectively.     

Subwavelength ripple formation induced by tightly focused femtosecond laser radiation

Subwavelength ripples (<λ/4) are obtained by scanning a tightly focused beam (∼1 μm) of femtosecond laser radiation (λ = 800 nm, t_p = 100 fs) over the surface of either bulk fused silica and silicon and Er:BaTiO₃. The ripple pattern extends coherently over many overlapping laser pulses parallel and perpendicular to the polarisation. Investigated are the dependence of the ripple spacing on the spacing of successive pulses, the direction of polarisation and the material. The evolution of the ripples is investigated by applying pulse bursts with N = 1 to 20 pulses. The conditions under which these phenomena occur are specified, and some possible mechanisms of ripple growth are discussed. Potential applications are presented.     

Ultra fast melting process in femtosecond laser crystallization of thin a-Si layer

In this paper, we investigated the mechanism of crystallization induced by femtosecond laser irradiation for an amorphous Si (a-Si) thin layer on a crystalline Si (c-Si) substrate. The fundamental, SHG, THG wavelength of a Ti:Sapphire laser was used for the crystallization process. To investigate the processed areas we performed Laser Scanning Microscopy (LSM), Transmission Electron Microscopy (TEM) and Imaging Pump-Probe measurements. Except for 267 nm femtosecond laser irradiation, the crystallization occurred well. The threshold fluences for the crystallization using 800 nm and 400 nm femtosecond laser irradiations were 100 mJ/cm² and 30 mJ/cm², respectively. TEM observation revealed that the crystallization occurred by epitaxial growth from the boundary surface between the a-Si layer and c-Si substrate. The melting depths estimated by Imaging Pump-Probe measurements became shallower when the shorter wavelength was used.