Submicron foaming in gelatine by nanosecond and femtosecond pulsed laser irradiation

We compare the foaming characteristics induced by irradiation with single ns and fs laser pulses of UV, VIS and IR wavelengths on gelatines differing in gel strength (bloom values 75 and 225) and in crosslinking degree. We have observed that while laser irradiation with nanoseconds leads to the formation of a microfoam layer at 266 nm, and melting and crater formation at longer wavelengths (532 and 1064 nm), fs pulse irradiation leads to submicron foaming at all wavelengths studied (266, 400 and 800 nm). These results show the possibility of controlling the submicrometric foam structure in this biomaterial and can shed light into the working mechanisms of fs laser nanoprocessing in biomaterials, where increase of temperature, thermoelastic stress generation, and stress-induced bubble formation are mediated by the generated plasma.     

Enhanced near field mediated nanohole fabrication on silicon substrate by femtosecond laser pulse

Investigation of the process of nanohole formation on silicon surface mediated with near electromagnetic field enhancement in vicinity of gold particles is described. Gold nanospheres with diameters of 40, 80 and 200 nm are used. Irradiation of the samples with laser pulse at fluences below the ablation threshold for native Si surface, results in a nanosized surface modification. The nanostructure formation is investigated for the fundamental (λ = 800 nm, 100 fs) and the second harmonic (λ = 400 nm, 250 fs) of the laser radiation generated by ultrashort Ti:sapphire laser system. The near electric field distribution is analyzed by an Finite Difference Time Domain (FDTD) simulation code. The properties of the produced morphological changes on the Si surface are found to depend strongly on the polarization and the wavelength of the laser irradiation. When the laser pulse is linearly polarized the produced nanohole shape is elongated in the E-direction of the polarization. The shape of the hole becomes symmetrical when the laser radiation is circularly polarized. The size of the ablated holes depends on the size of the gold particles, as the smallest holes are produced with the smallest particles. The variation of the laser fluence and the particle size gives possibility of fabricating structures with lateral dimensions ranging from 200 nm to below 40 nm. Explanation of the obtained results is given on the basis simulations of the near field properties using FDTD model and Mie's theory.     

Femtosecond and nanosecond laser damage thresholds of doped and undoped triazenepolymer thin films

The influence of pulse duration on the laser-induced damage in undoped or infrared-absorbing-dye doped thin triazenepolymer films on glass substrates has been investigated for single, near-infrared (800 nm) Ti:sapphire laser pulses with durations ranging from 130 fs up to 540 fs and complementarily for infrared (1064 nm) Nd:YAG ns-laser single-pulse irradiation. The triazenepolymer material has been developed for high resolution ablation with irradiation at 308 nm. Post-irradiation optical microscopy observations have been used to determine quantitatively the threshold fluence for permanent laser damage. In contrast to our previous studies on a triazenepolymer with different composition [J. Bonse, S.M. Wiggins, J. Solis, T. Lippert, Appl. Surf. Sci. 247 (2005) 440], a significant dependence of the damage threshold on the pulse duration is found in the sub-picosecond regime with values ranging from ∼500 mJ/cm² (130 fs) up to ∼1500 mJ/cm² (540 fs). Other parameters such as the film thickness (50 nm and 1.1 μm samples) or the doping level show no significant influence on the material behavior upon irradiation. The results for fs- and ns-laser pulse irradiation are compared and analyzed in terms of existent ablation models.     

Femtosecond laser-induced fragmentation and cluster formation studies of solid phase trinitrotoluene using time-of-flight mass spectrometry

We use surface-femtosecond laser mass spectrometry to study the fragments/products formed when trinitrotoluene (TNT) is subjected to femtosecond laser pulse irradiation and to study the conditions under which TNT is removed from a solid surface. In surface-femtosecond laser mass spectrometry a compound is deposited on a solid substrate and is desorbed into vacuum by femtosecond irradiation forming a plume of ionized and neutral species. The positive or negative ions are then accelerated by an electric potential and allowed to drift in the field-free region of a time-of-flight mass spectrometer. The mass-to-charge ratio of each ion is obtained using the value of the accelerating field and the ion flight time. In this paper we report femtosecond laser mass spectra for the positive ions formed by desorbing TNT with 130 fs pulses centered at 800 nm for fluences ranging from 7 to 1.4 × 10⁵ J/m². The conditions under which TNT removal and ionization occur are also discussed.     

The potential of UV femtosecond laser ablation for varnish removal in the restoration of painted works of art

Despite significant advances, laser ablation with nanosecond pulses presents limitations in dealing with the restoration of classes of painted works of art, such as paintings with a very thin layer of varnish. Femtosecond laser processing promises the means for overcoming such limitations. To this end, femtosecond ablation of two typical varnishes, dammar and mastic, is examined. For these varnishes, processing by Ti:Sapphire irradiation (800 nm) turns out to be ineffective. In contrast, irradiation with 248 nm ∼500 fs laser pulses results in a higher etching resolution (etching rates of ∼1 μm/pulse or less). For irradiation with few laser pulses at moderate laser fluences, etched morphology is far smoother than in the processing with nanosecond laser pulses. Furthermore, chemical modifications are considerably reduced (by nearly an order of magnitude), and exhibit a number of additional novel differences. Both etching rates and extent of chemical modifications are largely independent of varnish absorptivity. In all, femtosecond UV laser irradiation is indicated to hold a high potential, offering new perspectives for the restoration of painted works of art. Finally, a tentative model is advanced accounting in a consistent way for the observations.     

Nanofoaming dynamics in biopolymers by femtosecond laser irradiation

We have recently shown that irradiation of self-standing films of the biopolymers collagen and gelatine with single femtosecond laser pulses produces a nanofoaming layer with regular bubble size which can be controlled by wavelength selection. Following these initial studies, here we report on the temporal evolution of the foaming effect by measurements in situ and in real time of the change in the transmittance of a cw probe HeNe laser through the irradiated films. Self standing films of the biopolymers were irradiated with 90 fs laser pulses at 800, 400, and 266 nm. For fluences below and above the modification threshold a permanent attenuation of the transmission occurs (increasing with fluence). The initial decay of the transmission is fast (around few tens of ns), and is followed by dynamics in the longer timescale (micro and milliseconds). The temporal evolution of the transmission measured upon fs laser irradiation is similar with that determined in the irradiation of the biopolymer films at 248 nm with 25 ns laser pulses. The method allows separating in time the different processes occurring after irradiation that lead to a permanent nanofoaming structure, while the results allow us to understand the mechanisms of femtosecond laser processing of the biopolymers and their interest in biomedical applications.     

Evolution of surface morphology of NiO thin films under swift heavy ion irradiation

NiO nanoparticle thin films grown on Si substrates were irradiated by 107 MeV Ag⁸⁺ ions. The films were characterized by glancing angle X-ray diffraction and atomic force microscopy. Ag ion irradiation was found to influence the shape and size of the nanoparticles. The pristine NiO film consisted of uniform size (∼100 nm along major axis and ∼55 nm along minor axis) elliptical particles, which changed to also of uniform size (∼63 nm) circular shape particles on irradiation at a fluence of 3 × 10¹³ ions cm⁻². Comparison of XRD line width analysis and AFM data revealed that the particles in the pristine films are single crystalline, which turn to polycrystalline on irradiation with 107 MeV Ag ions.     

KrF laser ablation of a polyethersulfone film: Effect of pulse duration on structure formation

Polyethersulfone (PES) films were processed with KrF laser irradiation of different pulse durations (τ). Scanning electron microscopy (SEM) and Raman spectroscopy were employed for the examination of the morphology and chemical composition of the irradiated surfaces, respectively. During ablation with 500 fs and 5 ps pulses, localized deformations (beads), micro-ripple and conical structures were observed on the surface depending on the irradiation fluence (F) and the number of pulses (N). In addition, the number density of the structures is affected by the irradiation parameters (τ, F, N). Furthermore, at longer pulse durations (τ = 30 ns), conical structures appear at lower laser fluence values, which are converted into columnar structures upon irradiation at higher fluences. The Raman spectra collected from the top of the structures following irradiation at different pulse durations revealed graphitization of the ns laser treated areas, in contrast to those processed with ultra-short laser pulses.     

Structure formation on the surface of alloys irradiated by femtosecond laser pulses

Laser-induced periodic surface structures with different spatial characteristics have been observed after multiple linearly polarized femtosecond laser pulse (120 fs, 800 nm, 1 Hz to 1 kHz pulse repetition frequency) irradiation on alloys. With the increasing number of pulses, nanoripples, classical ripples and modulation ripples with a period close to half of classical ripples have all been induced. The generation of second-harmonic has been supposed to be the main mechanism in the formation of modulation ripples.     

Morphological characteristics of amorphous Ge2Sb2Te5 films after a single femtosecond laser pulse irradiation

The morphology of materials resulting from laser irradiation of the single-layer and the multilayer amorphous Ge₂Sb₂Te₅ films using 120 fs pulses at 800 nm was observed using scanning electron microscopy and atomic force microscopy. For the single-layer film, the center of the irradiated spot is depression and the border is protrusion, however, for the multilayer film, the center morphology changes from a depression to a protrusion as the increase of the energy. The crystallization threshold fluence of the single-layer and the multilayer film is 22 and 23 mJ/cm², respectively.     

Two-color two-photon excitation of indole using a femtosecond laser regenerative amplifier

The fluorescence emission from indole resulting from two-color two-photon (2C2P) excitation with 400 and 800 nm wavelengths is observed, using the second harmonic and fundamental wavelength of a 800 nm 40 fs pulsed Ti:Sapphire femtosecond (fs) regenerative amplifier operating at a repetition rate of 1 kHz. By delaying one fs laser pulse relative to the other, the cross correlation of fluorescence is observed, which indicates the generation of 2C2P fluorescence signal in the experiment. The strongest 2C2P fluorescence emission characterized by the peak of cross correlation curve suggests optimal temporal overlap of the two fs laser pulses. The 2C2P fluorescence signal is linearly dependent on the total excitation intensity. The fluorescence signals with 400 nm and 800 nm irradiation alone are also demonstrated and discussed in this paper.     

Femtosecond pulsed laser deposition of diamond-like carbon films: The effect of double laser pulses

The bonding structure of carbon films prepared by pulsed laser deposition is determined by the plasma properties especially the change of the kinetic energy. Using double laser pulses the ablation process and the characteristics of the generated plasma can be controlled by the setting of the delay between the pulses. In our experiments, amorphous carbon films have been deposited in vacuum onto Si substrates by double pulses from a Ti:sapphire laser (180 fs, λ = 800 nm, at 1 kHz) and a KrF laser system (500 fs, λ = 248 nm, at 5 Hz). The intensities have been varied in the range of 3.4 × 10¹² to 2 × 10¹³ W/cm². The morphology and the main properties of the thin layers were investigated as a function of the time delay between the two ablating pulses (0-116.8 ps) and as a function of the irradiated area on the target surface. Atomic force microscopy, spectroscopic ellipsometry and Raman-spectroscopy were used to characterize the films. It was demonstrated that the change of the delay and the spot size results in the modification of the thickness distribution of the layers, and the carbon sp²/sp³ bonding ratio.     

Raman study of phase transformation of TiO2 rutile single crystal irradiated by infrared femtosecond laser

Titanium dioxide (TiO₂) rutile single crystal was irradiated by infrared femtosecond (fs) laser pulses with repetition rate of 250 kHz and phase transformation of rutile TiO₂ was observed. Micro-Raman spectra show that the intensity of E_g Raman vibrating mode of rutile phase increases and that of A_1g Raman vibrating mode decreases apparently within the ablation crater after fs laser irradiation. With increasing of irradiation time, the Raman vibrating modes of anatase phase emerged. Rutile phase of TiO₂ single crystal is partly transformed into anatase phase. The anatase phase content transformed from rutile phase increased to a constant with increasing of fs pulse laser irradiation time. The study indicates the more stable rutile phase is transformed into anatase phase by the high pressure produced by fs pulse laser irradiation.     

Control of tribological properties of diamond-like carbon films with femtosecond-laser-induced nanostructuring

This paper reports tribological properties of diamond-like carbon (DLC) films nanostructured by femtosecond (fs) laser ablation. The nanostructure was formed in an area of more than 15 mm × 15 mm on the DLC surface, using a precise target-scan system developed for the fs-laser processing. The frictional properties of the DLC film are greatly improved by coating a MoS₂ layer on the nanostructured surface, while the friction coefficient can be increased by surface texturing of the nanostructured zone in a net-like patterning. The results demonstrate that the tribological properties of a DLC surface can be controlled using fs-laser-induced nanostructuring.     

Mg-based photocathodes prepared by ns, ps and fs PLD for the production of high brightness electron beams

Mg-based films have been prepared by pulsed laser deposition technique for photocathode applications. We have investigated the influence of pulse laser duration on morphology and photoemissive properties. Two laser sources have been used, generating pulses of 30 ns at 308 nm (XeCl excimer laser), 5 ps and 500 fs at 248 nm (KrF excimer laser) to grow Mg films onto Si and Cu substrates in high vacuum (∼10⁻⁷ Pa) and at room temperature. Morphological investigations carried out by scanning electron microscopy (SEM) have revealed that, in our experimental conditions, the number and the mean size of the droplets on the films surfaces decreases as the pulse laser duration shortens. The contamination level of Mg film surfaces have been studied by energy dispersive X-ray spectroscopy (EDX). The photoelectron performances in terms of quantum efficiency (QE) and emission stability have been tested in a UHV DC photodiode cell (10⁻⁷ Pa). Measures of the QE of the samples surfaces have revealed a decrease on the initial value for Mg-based photocathodes prepared by fs laser (from 7.8 × 10⁻⁴ to 6.6 × 10⁻⁴) PLD with respect to ps (from 6.2 × 10⁻⁴ to 7.4 × 10⁻⁴) and ns lasers (from 5.0 × 10⁻⁴ to 1.6 × 10⁻³). A comparison among Mg-based photocathodes prepared by ns, ps and fs PLD for the production of high brightness electron beams has been presented and discussed.     

Ultraviolet irradiation induced changes in the surface of phenolphthalein poly(ether sulfone) film

Changes in surface characteristics of phenolphthalein poly(ether sulfone) (PES-C) film induced by ultraviolet (UV) irradiation were investigated. The surface properties of the pristine and irradiated films were studied by attenuated total-reflection FTIR (FTIR-ATR), X-ray photoelectron spectroscopy (XPS), contact angle measurements and atomic force microscopy (AFM). It was found that photooxidation degradation took place on the sample surface after irradiation and the oxygen content in the surface increased as evidenced by FTIR-ATR and XPS results. The water contact angle of the irradiated films decreased with increasing irradiation time, which was ascribed to the increased polarity of the surface induced by photooxidation. The etching of ultraviolet irradiation induced the roughening of PES-C surface after irradiation with its root-mean-square roughness (RMS) determined by AFM increased from 2.097 nm before irradiation to 7.403 nm in the area of 25 μm × 25 μm.     

Emission spectra investigation of fs induced NPs probed by the ns laser pulse of a fs/ns DP-LIBS orthogonal configuration

A dual-pulse fs/ns laser induced breakdown spectroscopy configuration, where an initial 250 fs ablating pulsed laser followed by a delayed ns laser beam placed at a fixed distance, orthogonally with the expanding plasma plume, has been used in air on a Al₆₅Cu₂₃Fe₁₂ quasicrystal. The obtained emission data were acquired with a set-up arrangement providing space detections, with a resolution up to 15 μm, of the ns laser pulse generated signals. Assuming the fulfillment of local thermodynamic equilibrium conditions, the role played by the time lag between the two laser beams on the induced plasma excitation temperatures and electronic densities, as well as a space resolved process survey, has been followed. The spatial and time resolved spectra show, almost, steady values of the determined elementary plasma features with the development of nanoparticles occurring during the fs laser pulsed ablation process. The ns laser probe of the dual-pulse LIBS configuration here presented confirms that the nanoparticles induced can be largely widespread in both space and time whose compositions, overall, could retain the starting target stoichiometry. It is shown that these nanoparticles formation can actually take place at different times following the initial ultra-short laser beam incidence and that, especially at long inter-pulse delays (>100 μs), modest compositional changes can be observed.     

Femtosecond pulsed laser deposition of nanostructured TiO2 films

Nanostructured deposits of TiO₂ were grown on Si (1 0 0) substrates by laser ablating a TiO₂ sintered target in vacuum or in oxygen using a Ti:sapphire laser delivering 80 fs pulses. The effect of the laser irradiation wavelength on the obtained nanostructures, was investigated using 800, 400 and 266 nm at different substrate temperatures and pressures of oxygen. The composition of the deposits was characterized using X-ray photoelectron spectroscopy (XPS) and the surface morphology was studied by environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). Deposits are absent of microscopic droplets in all conditions explored. The best deposits, constituted by nanoparticles of an average diameter of 30 nm with a narrow size distribution, were obtained at the shorter laser wavelength of 266 nm under vacuum at substrate room temperature.     

Optical emission spectroscopy investigation of an ultra-short laser induced titanium plasma reheated by a ns laser pulse

The dynamics of a titanium plasma species, induced in air by coupling a fs-ablating laser pulse with an orthogonal ns-reheating laser source placed at the fixed distance of 1.0 mm from the target surface, has been followed by temporally resolved emission spectroscopy. The temporal evolutions of plasma features such as excitation temperatures and electron densities have been evaluated by using two different laser energies of the first fs-ablating laser pulse (0.8 mJ and 3.0 mJ). Optimum inter-pulse delay times, experimentally determined, of 250 μs and 500 μs were used for the fs laser energy of 3.0 mJ and 0.8 mJ, respectively. By experimental inspections of the main plasma species electronic transitions so obtained, a strong enhancement was evaluated up to one and two orders of magnitude for Ti(I) and Ti(II), respectively. Independently from the fs laser energy employed, the plasma features showed the same temporal behaviour implying that the ns-reheating characteristics of this process belong to the reheating mechanism itself. The experimental results have been discussed and the excited species evolutions and elementary processes involved, as well as, the local thermodynamic equilibrium departures, have been outlined.     

Investigation of the two-photon polymerisation of a Zr-based inorganic-organic hybrid material system

Two-photon polymerisation of photo-sensitive materials allows the fabrication of three dimensional micro- and nano-structures for photonic, electronic and micro-system applications. However the usable process window and the applicability of this fabrication technique is significantly determined by the properties of the photo-sensitive material employed. In this study investigation of a custom inorganic-organic hybrid system, cross-linked by a two-photon induced process, is described. The material was produced by sol-gel synthesis using a silicon alkoxide species that also possessed methacrylate functionality. Stabilized zirconium alkoxide precursors were added to the precursor solution in order to reduce drying times and impart enhanced mechanical stability to deposited films. This enabled dry films to be used in the polymerisation process. A structural, optical and mechanical analysis of the optimised sol-gel material is presented. A Ti:sapphire laser with 80 MHz repetition rate, 100 fs pulse duration and 795 nm is used. The influence of both material system and laser processing parameters including: laser power, photo-initiator concentration and zirconium loading, on achievable micro-structure and size is presented.