Mn助剂对K-Co-Mo催化剂结构及CO加氢合成低碳醇性能的影响

通过溶胶-凝胶法合成了一系列Mn掺杂K-Co-Mo催化剂,并利用X射线衍射、N₂吸脱附、NH₃程序升温脱附、原位漫反射红外光谱以及X射线吸收谱等技术对催化剂的结构进行了表征.活性测试结果显示Mn掺杂催化剂比未掺杂催化剂表现更高的合成低碳醇的催化活性,尤其是C₂₊醇的选择性得到了明显的提高.醇产物分布偏离了ASF分布规律,甲醇的含量显著减少,乙醇成为主要醇产物.表征结果表明Mn助剂的加入增强了Co和Mo之间的相互作用,促进了醇生成活性中心Co-Mo-O物种的生成.显著减少了催化剂强酸性位的数量,促进了弱酸性位的产生,有利于醇产物的生成.助剂的加入有利于催化剂对CO的线性和桥式吸附,促进了醇产物的生成和碳链的增长,提高了催化剂对C₂₊醇的选择性.     

利用生物质合成气在钼基催化剂上制备混合醇

采用柠檬酸作络合剂的溶胶凝胶法制备了一系列的钼基催化剂,并应用到从生物质气化合成气有效合成低碳混合醇的实际过程中. 在钼基催化剂中,Cu₁Co₁Fe₁Mo₁Zn_0.5-6%K催化剂具有相对较高的混合醇时空产率. 通过实验发现, 反应温度在340 oC以下时,碳转化率随着反应温度的增加而不断上升,总醇的选择性却逐渐下降. 在试验测试的条件内,从生物质气化合成气合成的混合醇最大产率为494.8 g/(kg_catal·h),其中C2⁺醇(C2-C6高碳醇)占总醇含量的80.4%. 在不同的钼基催化剂上合成的混合醇,其醇分布除甲醇以外均符合Schulz-Flory方程. 在醇类产物中,C2以上的高级醇含量占总醇重量的百分比为70%-85%. 同时,利用X射线衍射和BET等表征手段对钼基催化剂的形态和结构进行了表征. 从生物质合成气生产的洁净生物质燃料混合醇具有较高的辛烷值,可以用作运输燃料或汽油的添加剂.     

光沉积Ru和RuO2的锐钛矿TiO2纳米片的光解水产氧

采用水热法以HF作为结构调控剂合成了主要暴露（001）面的锐钛矿TiO₂纳米片,通过光沉积方法分别合成了负载Ru和RuO₂物种的光催化剂。利用X射线衍射、透射电镜和氢气程序升温还原等分析表征了催化剂的结构性质。通过光解水产氧反应来研究催化剂的催化性能,详细考察了Ru含量、负载方式以及氧化和还原处理等因素的影响,光解水产氧速率的差异证明了Ru物种在不同晶面的电荷-空穴分离效应。与负载单一助催化剂的Ru/TiO₂和RuO₂/TiO₂样品相比,活性最优的0.5%Ru-1.0%RuO₂/TiO₂样品由于负载了双助催化剂,其催化活性得到更大的提高,证实了在锐钛矿TiO₂上的晶面电荷-空穴分离效应.     

焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

钴改性Fe3O4-MnO2催化转化生物质合成气制备液体燃料

本文制备了用于费托合成反应的钴改性Fe₃O₄-MnO₂双功能催化剂,并探究了钴负载量对Fe-Co协同效应的影响以及Fe₁Co_xMn₁催化剂的费托合成反应性能. 实验发现,在Fe₃O₄-Mn催化剂中加入Co可促进铁氧化物的还原、增加反应过程中铁位点的活性. 此外,Co的加入可增强Fe-Co金属间的电子转移,加强两者的协同作用,提高催化性能. Co负载较高的Fe₁Co_xMn₁催化剂可进一步促进加氢反应能力,使产品分布向短链烃方向转移. 在280 ^°C、2.0 MPa和3000 h^-1的最佳工况条件下,Fe₁Co₁Mn₁催化剂的液体燃料收率最高.     

利用EPR研究三氧化钼中氧还活性位点形成的温度依赖性

本文利用热处理还原法,利用三氧化钼诱导形成具有氧化还原活性的中间产物及其温度相关特性. 电子顺磁共振波谱(EPR)实验结果表明,热处理后在Mo^VI离子被还原成Mo^V离子并形成了超氧阴离子自由基O₂^-. 这两种活性中心的最佳热还原温度约300∽350 ^°C. 自350 ^°逐渐升温,两种EPR信号强度迅速下降,下降∽50%所对应的温度是400∽450 ^°C;当温度升至600 ^°C或更高时,EPR信号降至0. 结果表明,较高温处理或持续长时间处理都使热还原更容易发生,积累了越来越多的电子,在基底中形成类似于反铁磁耦合的电子离域. 随着离域程度增大,EPR信号强度开始下降并直至消失.     

煅烧温度对Cu/HMOR催化剂结构及其催化二甲醚羰基化反应性能影响

采用离子交换法在不同煅烧温度下制备HMOR负载Cu(Cu/HMOR)催化剂,用于催化二甲醚(DME)羰基化合成乙酸甲酯(MA)反应. 活性测试结果表明430 oC煅烧制得Cu/HMOR具有较好催化活性,在210 oC、1.5 MPa、空速4883 h^-1下DME转化率为97.2%,MA选择性为97.9%. 对催化剂进行X射线衍射、N₂物理吸附、NH₃程序升温脱附、CO程序升温脱附及拉曼方法表征. 催化剂经一定的煅烧温度有利于Cu离子迁移及扩散和硝酸铜完全分解,从而使HMOR载体具有较多的酸性活性位、大比表面、适宜的微孔结构以及更多的CO吸附位.     

介孔SO42-/Zr-SBA-15催化废弃油制生物柴油

采用廉价的无机锆源(无水硝酸锆)通过一步法合成表面含强Lewis酸位的SO₄^2-/Zr-SBA-15,该催化剂材料在废弃食用油和甲醇酯交换制生物柴油过程中表现出良好的催化活性和选择性. 实验考察了酯交换反应的最佳条件为：反应温度160 oC、反应时间12 h、催化剂Zr:Si为0.11、催化剂用量为10%、醇油比30:1. SO₄^2-/Zr-SBA-15在最佳反应条件下可使甘油三酯的转化率达到92.3%,脂肪酸甲酯的产率为91.7%. SO₄^2-/Zr-SBA-15具有高比表面积的介孔结构和表面酸性,且具有良好的反应稳定性和重复性,反应7次后的脂肪酸甲酯的产率仍稳定保持在74 ±1%.     

海胆状CoCu双金属纳米复合材料的合成及其在甘油氢解制丙二醇中的催化性能

以Ru为多相成核剂和硬脂酸为表面活性剂,在多元醇溶液中合成了CoCu双金属纳米复合物,并在甘油选择性氢解制丙二醇中评价了其催化性能．结果表明,硬脂酸作为结构导向剂可诱使Co纳米晶沿着一维方向生长,形成纳米线．当Co²⁺和Cu²⁺共存于多元醇溶液中,由于Cu²⁺较高的氧化还原电位,首先被还原成Cu⁰,进而增长成100～300 nm的球形粒子．在Cu粒子表面,Co²⁺被还原成核,在表面活性剂的结构导向作用下生长为长度为100～500 nm的纳米棒,从而形成海胆状CoCu双金属纳米复合结构．在甘油选择性氢解制丙二醇反应中,海胆状CoCu双金属复合催化剂的单位表面活性与丙二醇选择性均明显高于单金属Co纳米线和Cu球形粒子,在Co₉₀Cu₁₀催化剂上获得33%的丙二醇收率．这可能是由于Co和Cu界面的协同效应促进了甘油的转化所致．     

活化气氛对钼基合成醇催化剂的结构和性能的影响

Activated carbon supported Mo-based catalysts were prepared and reduced under different activation atmospheres, including pure H₂, syngas (H₂/CO=2/1), and pure CO. The catalysts structures were characterized by X-ray diffraction, X-ray absorption fine structure, and in situ diffuse reflectance infrared Fourier transform spectroscopy. The catalytic performance for the higher alcohol synthesis from syngas was tested. The pure H₂ treatment showed a high reduction capacity. The presence of a large amount of metallic Co⁰. and low valence state Mo^φ+ (0<φ<2) on the surface suggested a super activity for the CO dissociation and hydrogenation, which promoted hydrocarbons formation and reduced the alcohol selectivity. In contrast, the pure CO-reduced catalyst had a low reduction degree. The Mo and Co species at the catalyst mainly existed in the form of Mo⁴⁺ and Co²⁺. The syngas-reduced catalyst showed the highest activity and selectivity for the higher alcohols synthesis. We suggest that the syngas treatment had an appropriate reduction capacity that is between those of pure H₂ and pure CO and led to the coexistence of multivalent Co species as well as the enrichment of Mo^δ+ on the catalyst''s surface. The synergistic effects between these active species provided a better cooperativity and equilibrium between the CO dissociation, hydrogenation and CO insertion and thus contributed beneficially to the formation of higher alcohols.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.