Ga1-xInxNyAs1-y/GaAs量子阱中电子-LO声子的散射率

在有效质量近似下利用打靶法求出Ga_1-xIn_xN_yAs_1-y/GaAs量子阱中的本征能级E_n, 并通过费米黄金规则计算电子-LO声子由第一激发态到基态的散射率和平均散射率随温度、阱宽以及氮(N)和铟(In)组分变化的规律. 计算结果表明: 在In 组分恒定的情况下, 随着N组分的增加, 散射率和平均散射率增加; 在N组分恒定的情况下, 随着In组分的增加, 散射率和平均散射率减小; 随着温度的增加, 在温度较低时散射率和平均散射率随温度的增加变化不大, 在温度较高时随温度的增加而增加; 随着阱宽的增加, 散射率和平均散射率都是先增加到一个最大值, 然后再减小, 最大值出现在阱宽200 Å附近. 计算结果对Ga_1-xIn_xN_yAs_1-y/GaAs量子阱在光电子器件应用方面有一定的指导意义. 关键词： 费米黄金规则 1-xIn_xN_yAs_1-y/GaAs量子阱')" href="#">Ga_1-xIn_xN_yAs_1-y/GaAs量子阱 LO声子 散射率     

The influence of the Dresselhaus spin--orbit coupling on the tunnelling magnetoresistance in ferromagnet/ insulator /semiconductor/ insulator /ferromagnet tunnel junctions

This paper investigates the effect of Dresselhaus spin--orbit coupling on the spin-transport properties of ferromagnet/insulator/semiconductor/insulator/ferromagnet double-barrier structures. The influence of the thickness of the insulator between the ferromagnet and the semiconductor on the polarization is also considered. The obtained results indicate that (i) the polarization can be enhanced by reducing the insulator layers at zero temperature, and (ii) the tunnelling magnetoresistance inversion can be illustrated by the influence of the Dresselhaus spin--orbit coupling effect in the double-barrier structure. Due to the Dresselhaus spin--orbit coupling effect, the tunnelling magnetoresistance inversion occurs when the energy of a localized state in the barrier matches the Fermi energy E_F of the ferromagnetic electrodes.     

InAlAs/GaSbAs/InP DHBT与InP/GaSbAs/InP DHBT性能比较分析

双异质结双极晶体管(DHBT)的性能与发射区-基区(E-B) 异质结和基区-集电区(B-C)异质结的能带突变类型关系密切, 本文基于热场发射-扩散模型, 对两类不同能带结构类型的新型DHBT的性能做了比较分析. 结论表明: 与作为当今研究热点的E-B和B-C异质结构均为全交错II型能带结构的InP/GaSbAs/InP DHBT的性能相比, E-B异质结采用传统I型、B-C异质结采用交错II型的一类新型能带结构的InAlAs/GaSbAs/InP DHBT虽然在开启电压上更高, 但具有更好的电流驱动能力、直流增益和高频性能.     

Nb/Al-AlO_x/Nb隧道结制备中压控电压源阳极氧化工艺研究

采用计算机程控的压控电压源阳极氧化模式研究制备出自对准Nb/Al-AlOx/Nb隧道结的绝缘层Nb2O5/Al2O3/Nb2O5。研究了氧化电压、氧化层的厚度和氧化时间的关系。当阳极氧化电压变化率低于8V/min时,阳极氧化层的厚度基本取决于氧化电压的大小,而与氧化电压变化率无关。我们已采用电压源阳极氧化技术成功制备出超导Nb/Al-AlOx/Nb隧道结。     

InAIAs／GaSbAs／InPDHBT与InP／GaSbAs／InPDHBT性能比较分析

双异质结双极晶体管（DHBT）的性能与发射区-基区（E．B）异质结和基区．集电区（B．C）异质结的能带突变类型关系密切,本文基于热场发射．扩散模型,对两类不同能带结构类型的新型DHBT的性能做了比较分析．结论表明：与作为当今研究热点的E．B和B．C异质结构均为全交错II型能带结构的InP／GaSbAs／InPDHBT的性能相比,E．B异质结采用传统I型、B．C异质结采用交错II型的一类新型能带结构的InAlAs／GaSbAs／InPDHBT虽然在开启电压上更高,但具有更好的电流驱动能力、直流增益和高频性能．     

单核/双壳结构CdSe/CdS/ZnS纳米晶的合成与发光性质

以巯基乙酸为稳定剂,在水溶液中合成了单核/双壳结构的CdSe/CdS/ZnS纳米晶。在内核CdSe和外壳ZnS之间的内壳CdS作为晶格匹配调节层,能够很好的改善核/壳界面处的性能,而且,最外层ZnS能够最大程度地使激子受限。用TEM和XPS对纳米晶进行了表征,并且用光致发光光谱和吸收光谱对不同核壳结构的纳米晶的发光性能进行了比较,结果表明单核/双壳结构的纳米晶具有更加优异的发光特性。     

应变层异质结ZnS/ZnSe、ZnS/ZnSxSe1-x和ZnSe/ZnSxSe1-x价带带阶的研究

采用基于原子球近似下线性Mufin-Tin轨道(LMTO-ASA)的平均键能计算方法,研究了以ZnS_xSe_1-x为衬底,沿(001)方向外延生长的应变层异质结ZnS/ZnSe、ZnS/ZnS_xSe_1-x和ZnSe/ZnS_xSe_1-x的价带带阶值ΔE_v(x).研究表明,ΔE_v(x)值随衬底合金组分x单调变化。且两者的关系是非线性的。在此计算结果与其它理论计算和实验结果符合较好。     

Andreev Tunneling Through a Ferromagnet/Quantum-Dot/Superconductor System

We study Andreev tunneling through a ferromagnet/quantum-dot (QD)/superconductor system. By usingnonequilibrum Green function method, the averaged occupation of electrons in QD and the Andreev tunneling currentare studied. Comparing to the norma-metal/quantum-dot/superconductor, the system shows significant changes: (i)The averaged occupations of spin-up and spin-down electrons are not equal. (ii) With the increase of the polarizationof ferromagnetic lead, the Andreev reflection current decreases. (iii) However, even the ferromagnetic lead reaches fullpolarization, the averaged occupation of spin-down electrons is not zero. The physics of these changes is discussed.     

Analytics/Methods

An overview is presented of biomedical applications of stable isotopes in general, but mainly focused on the activities of the Center for Liver, Digestive and Metabolic Diseases of the University Medical Center Groningen. The aims of metabolic studies in the areas of glucose, fat, cholesterol and protein metabolism are briefly explained, as well as the principle of breath testing and the techniques to study body composition and energy expenditure. Much attention is paid to the analytical considerations based upon metabolite concentrations, sample size restrictions, the availability of stable isotope labelled substrates and dose requirements in relation to compound-specific isotope analysis. The instrumental advantages and limitations of the generally used techniques gas chromatography/reaction/isotope ratio mass spectrometry and gas chromatography/mass spectrometry are described as well as the novelties of the recently commercialised liquid chromatography/combustion/isotope ratio mass spectrometry. The present use and future perspective of infrared (IR) spectrometry for clinical and biomedical stable isotope applications are reviewed. In this respect, the analytical demands on IR spectrometry are discussed to enable replacement of isotope ratio mass spectrometry by IR spectrometry, in particular, for the purpose of compound-specific isotope ratio analysis in biological matrices.     

PT/PZT/PT铁电薄膜的铁电畴和畴壁

用sol-gel法制备出了具有良好铁电性、纯钙钛矿结构的PbTiO₃/Pb(Zr_0.3Ti_0.7)O₃/PbTiO₃(PT/PZT/PT)新型夹心结构铁电薄膜.用扫描力显微镜(SFM)的压电响应模式获得了薄膜铁电畴的垂直于膜平面方向(OPP)、膜平面内(IPP)及OPP的相位和幅度图像，结合理论分析指出薄膜的电畴主要由c畴和偏离垂直于膜平面方向上的c畴构成，薄膜取向的复杂性导致了复杂的畴结构.对于［111］取向的薄膜，当偏离垂直于膜平面方向上的c畴在垂直膜平面方向和面内方向都相反时构成180°的畴壁，在垂直膜平面方向上相同、面内方向相反或由垂直膜平面方向上相反、面内方向相同时构成90°畴壁. 关键词： 铁电薄膜 PT/PZT/PT 电畴和畴壁 扫描力显微镜(SFM)     

电迁移对Ni/Sn3.0Ag0.5Cu/Au/Pd/Ni-P倒装焊点界面反应的影响

本文研究了150 ℃, 1.0× 10⁴ A/cm²条件下电迁移对Ni/Sn3.0Ag0.5Cu/Au/Pd/Ni-P倒装焊点界面反应的影响. 回流后在solder/Ni和solder/Ni-P的界面上均形成(Cu,Ni)₆Sn₅类型金属间化合物. 时效过程中两端界面化合物都随时间延长而增厚, 且化合物类型都由(Cu,Ni)₆Sn₅转变为(Ni,Cu)₃Sn₄. 电迁移过程中电子的流动方向对Ni-P层的消耗起着决定性作用. 当电子从基板端流向芯片端时, 电迁移促进了Ni-P层的消耗, 600 h后阴极端Ni-P层全部转变为Ni₂SnP层. 阴极界面处由于Ni₂SnP层的存在, 使界面Cu-Sn-Ni三元金属间化合物发生电迁移脱落溶解, 而且由于Ni₂SnP层与Cu焊盘的结合力较差, 在Ni₂SnP/Cu界面处会形成裂纹. 当电子从芯片端流向基板端时, 阳极端Ni-P层并没有发生明显的消耗. 电流拥挤效应导致了阴极芯片端Ni层和Cu焊盘均发生了局部快速溶解, 溶解到钎料中的Cu和Ni原子沿电子运动的方向往阳极运动并在钎料中形成了大量的化合物颗粒. 电迁移过程中(Au,Pd,Ni)Sn₄的聚集具有方向性, 即(Au,Pd,Ni)Sn₄因电流作用而在阳极界面处聚集.     

Novel attributes of AlGaN/AlN/GaN/SiC HEMTs with the multiple indented channel

In this paper, a high performance AlGaN/AlN/GaN/SiC High Electron Mobility Transistor (HEMT) with the multiple indented channel (MIC-HEMT) is proposed. The main focus of the proposed structure is based on reduction of the space around the gate, stop of the spread of the depletion region around the source–drain, and decrement of the thickness of the channel between the gate and drain. Therefore, the breakdown voltage increases, meanwhile the elimination of the gate depletion layer extension to source/drain decreases the gate–source and gate–drain capacitances. The optimized results reveal that the breakdown voltage and the drain saturation current increase about 178% and 46% compared with a conventional HEMT (C-HEMT), respectively. Therefore, the maximum output power density is improved by factor 4.1 in comparison with conventional one. Also, the cut-off frequency of 25.2 GHz and the maximum oscillation frequency of 92.1 GHz for the MIC-HEMT are obtained compared to 13 GHz and 43 GHz for that of the C-HEMT and the minimum figure noise decreased consequently of reducing the gate–drain and gate–source capacitances by about 42% and 40%, respectively. The proposed MIC-HEMT shows a maximum stable gain (MSG) exceeding 24.1 dB at 3.1 GHz which the greatest gain is yet reported for HEMTs, showing the potential of this device for high power RF applications.     

MgO衬底NbN/AlN/NbN多层膜的制备

本文主要讨论磁控溅射设备制备的NbN/AlN/NbN三层结构的技术工艺,为制备All-NbN的 NbN/AlN/NbN SIS 隧道结作准备.我们在室温下利用直流磁控溅射工艺制备了单晶NbN薄膜,并对其超导电性做了初步的研究;又利用射频磁控溅射工艺制备了取向较好的AlN薄膜.我们利用磁控溅射方法制作NbN/AlN/NbN多层薄膜,然后对制备SIS隧道结进行了一些探索.     

MgxZn1-xO/Au/MgxZn1-xO夹层透明导电薄膜的制备及光电性质研究

采用操作简单的溶胶-凝胶法和射频磁控溅射法在石英衬底上分别制备了MgxZn1-xO薄膜和MgxZn1-xO/Au/MgxZn1-xO夹层结构的透明导电薄膜并对样品进行退火处理。利用紫外-可见分光光度计、X射线衍射仪、光致发光、霍尔效应测试对在不同退火温度下薄膜的晶体结构、光学和电学性质进行表征分析,并研究退火温度对其影响。测试结果表明:所制备的薄膜样品均具有良好的c轴(c-axis)取向并呈现出六角纤锌矿结构。Mg组分的增加使得ZnO基薄膜的光学带隙逐渐增大,PL发光谱和吸收光谱的谱线出现了明显的蓝移现象,但薄膜的电学特性有所降低。而在MgxZn1-xO/Au/MgxZn1-xO夹层结构的薄膜样品中,Au夹层的存在使薄膜的光学性质变差,在紫外区域透光率约为60%。但薄膜的电学性质得到明显改善,相比MgxZn1-xO薄膜,其电阻率和迁移率显著提高。此外通过高温退火处理可以有效提高所制备薄膜的晶体质量,进一步提高样品电学特性,其中经过500℃退火后的薄膜迁移率达到了40.9cm2·Vs-1,电阻率为0.005 7Ω·cm。但随着退火温度的进一步升高,薄膜晶体尺寸从25.1nm增大到32.4nm,从而降低了该薄膜的迁移率。因此该夹层结构的MgxZn1-xO/Au/MgxZn1-xO薄膜对于促进ZnO基透明导电薄膜在深紫外光学器件中的应用有重要作用。     

背入射Au/ZnO/Al结构肖特基紫外探测器

设计制作了一种Au/ZnO/Al结构的紫外探测器,光的入射方式采用背入射式。ZnO薄膜是用磁控溅射在蓝宝石衬底上制备的。I-V测试表明:Au与ZnO形成了肖特基接触。得到探测器的光响应峰值在352nm,截止边为382nm,可见抑制比达一个量级。由于该探测器是一种垂直结构器件,对于进一步实现ZnO紫外探测器阵列及单光子探测有很好的研究价值。     

Analytical Result on the Supercurrent Through a Superconductor/Quantum-Dot/Superconductor Junction

We present an analytical result for the supercurrent across a superconductor/quantum-dot/superconductor junction. By converting the current integration into a special contour integral, we can express the current as a sum of the residues of poles. These poles are real and give a natural definition of the Andreev bound states. We also use the exact result to explain some features of the supercurrent transport behavior.     

PbTiO3/PbZr0.3Ti0.7O3/PbTiO3夹心结构铁电薄膜子晶层的优化

用Sol-Gel法制备了Pb_(1+x)TiO₃/PbZr_03Ti_07O₃/Pb_(1+x)TiO₃(PT/PZT/PT)夹心结构及PZT铁电薄膜，为了获得高质量的PT/PZT/PT夹心结构铁电薄膜，使用不同过量Pb配比(x)的PbTiO₃ (PT)层进行制备，以获得优化的PT子晶层.X射线     

PbTiO3/PbZr0.3Ti0.7O3/PbTiO3夹心结构铁电薄膜子晶层的优化

用Sol-Gel法制备了Pb_(1+x)TiO₃/PbZr_03Ti_07O₃/Pb_(1+x)TiO₃(PT/PZT/PT)夹心结构及PZT铁电薄膜,为了获得高质量的PT/PZT/PT夹心结构铁电薄膜,使用不同过量Pb配比(x)的PbTiO₃ (PT)层进行制备,以获得优化的PT子晶层.X射线 关键词： PT/PZT/PT 夹心结构 子晶 铁电薄膜     

Determination of conduction band edge characteristics of strained Si/Si1-xGex

The feature of conduction band （CB） of Tensile-Strained Si（TS-Si） on a relaxed Si1-xGex substrate is systematically investigated, including the number of equivalent CB edge energy extrema, CB energy minima, the position of the extremal point, and effective mass. Based on an analysis of symmetry under strain, the number of equivalent CB edge energy extrema is presented; Using the K.P method with the help of perturbation theory, dispersion relation near minima of CB bottom energy, derived from the linear deformation potential theory, is determined, from which the parameters, namely, the position of the extremal point, and the longitudinal and transverse masses （m1^＊ and mt^＊）are obtained.     

温度升高对PSⅡCP47/D1/D2/Cytb559复合物能量传递的影响

采用分幅扫描单光子计数荧光光谱装置,研究温度升高对PSⅡ CP47/D1/D2/Cyt b559复合物能量传递的影响.获得分别在20℃、42℃和48℃处理后,CP47/D1/D2/Cyt b559复合物主发射峰所在的波长未发生多大改变,均在682 nm,但其荧光强度逐渐降低,而大约730 nm处主发射峰的振动副带发生了明显的变化,42℃其弱峰趋势已不显著,相对荧光强度下降,48℃弱峰趋势已完全消失;最大峰值处获得两个时间组分,这两个组分都属于电荷重组.其中,1～2 ns组分随处理温度的升高变化不大,而7～20 ns组分随温度升高变化较大,并且逐渐延长.因此,处理温度的升高使CP47/D1/D2/Cyt b559复合物的二级结构、色素分布的空间位置发生变化,从而影响了CP47/D1/D2/Cyt b559复合物中的能量传递以及电荷重组.42℃已对其造成影响,而48℃对其影响很大.