毛细管干涉仪的理论分析

从几何光学出发,推导了毛细管干涉仪的从柱面透镜到接收屏的光线的光程．对光线追迹模拟,结果表明毛细管干涉仪的干涉条纹的形成可用双光束的干涉来解释．从柱面不同位置入射的两条光线可能具有相同的光程,而且从柱面透镜不同位置出发的两条光线可能到达接收屏的同一点,当它们满足相干条件时,就会形成干涉条纹．建立了干涉条纹的计算机模拟程序, 模拟了毛细管中液体折射率、毛细管内径、外径对干涉条纹的影响. 结果表明实验中应使用薄壁毛细管, 由于干涉条纹对柱面透镜到毛细管之间的距离非常敏感, 为提高精度, 建议在实验中用已知折射率的标样来确定这一距离.     

Estimation of partial optical path length in the brain in subject-specific head models for near-infrared spectroscopy

Three-dimensional head models with the structures constructed from the MR head images of 40 volunteers were constructed to analyze light propagation in the subject-specific head models. The mean optical path length in the head and the partial optical path length in the brain at 13 fiducial points for each volunteer were estimated to evaluate the intersubject and spatial variability in the optical path lengths. Although the intersubject variability in the optical path lengths is very high, the spatial variability in the average of the mean optical path length and partial optical path length is similar to the previously reported data. The mean optical path length in the head increases, whereas the partial optical path length in the brain decreases with an increase in the depth of the brain surface. The partial optical path length is highly correlated with the depth of the brain surface in comparison to the mean optical path length in the head.     

基于双通道马赫曾德尔调制器调制边带滤波的微波光子移相器

提出了一种基于双通道马赫曾德尔调制器(DPMZM)调制边带滤波的微波光子移相器。在双通道马赫曾德尔调制器的结构中,在一路马赫曾德尔干涉仪上实现抑制光载波的双边带调制输出,而在另一路马赫曾德尔的相位调节臂上通过调节偏置电压实现光载波信号的光学移相,两路光信号经过干涉合路后由光纤布拉格光栅(FBG)滤除其中一个一阶边带,最后输入到光电探测器(PD)进行光电转换得到移相的微波信号。实验结果表明,基于DPMZM调制边带滤波的微波光子移相器具有传输特性稳定、输出幅度波动小的优点。该结构还具有相移调节响应速度快、应用频带宽以及移相范围大于360°等特点。     

Sedimentation equilibria of ferrofluids: I. Analytical centrifugation in ultrathin glass capillaries

Analytical centrifugation is used for the first time to measure sedimentation equilibrium concentration profiles of a ferrofluid, a concentrated colloidal dispersion of strongly absorbing magnetic nanoparticles. To keep the optical absorbance from becoming too strong, the optical path length is restricted to 50 μm by placing the dispersion in a flat glass capillary. The concentration profile is kept from becoming too steep, despite the relatively high buoyant mass of the nanoparticles, by making novel use of a low-velocity analytical centrifuge that was not designed to measure equilibrium profiles. The experimental approach is validated by comparison with profiles obtained using an analytical ultracentrifuge. At concentrations of a few hundred grams per liter, the osmotic pressures calculated from the equilibrium profiles are lower than expected for hard spheres or non-interacting particles, due to magnetic dipolar interactions. By following the presented experimental approach, it will now also be possible to characterize the interparticle interactions of other strongly absorbing colloidal particles not studied before by analytical centrifugation.     

大气压下石英毛细管内氩等离子体放电的发射光谱诊断

在长度为20 cm的石英毛细管内利用两个边缘锋利的中空的针型电极之间的氩气放电产生了高电子密度的大气压等离子体。利用发射光谱对所获得的等离子体的几个重要参数进行了诊断。利用计算机谱线拟合法合成了300 nm附近OH(A-X)的(0-0)转动谱带并通过与测量谱线的比较确定了等离子体的气体温度,根据H_β谱线Stark展宽法计算了等离子体的电子密度,采用玻尔兹曼曲线斜率法依据测得的有关氩的发射光谱估算了等离子体的电子温度。研究结果表明,这种石英毛细管内弧光放电等离子体的气体温度约为(1 100±50)K;电子密度数量级在1014 cm-3;电子温度约为(14 515±500)K。     

高斯波束在湍流大气斜程传输中的闪烁问题研究

根据光波斜程传输理论以及随高度变化的ITU-R湍流大气结构常数模型,将水平传输的修正里托夫方法推广到了斜程传输问题中。导出了高斯波束入射时,在零内尺度湍流谱模型及考虑湍流内尺度效应和外尺度效应条件下,从弱起伏湍流区到强起伏湍流区闪烁指数随斜程里托夫方差变化的计算公式。讨论了不同传播高度、不同湍流内、外尺度对高斯波束斜程传输闪烁指数的影响。最后将有关数值计算结果与实验测量结果进行了比较和验证。     

Study on the Scintillation for Optical Wave Propagation in the Slant Path Through the Atmospheric Turbulence

Based on the theory of optical wave propagation in the slant path and the ITU-R turbulence structure constant model which is altitude dependent, the modified Rytov method, which is applicable to the optical wave propagation in the horizontal path, is extended to the propagation in the slant path. According to the spectrum model with non-zero inner scale, the scintillation index as a function of the Rytov variance is obtained from weak to strong fluctuation regions with plane wave and sphere wave incidence, respectively. Finally, the scintillation index with different zenith angles is analyzed, and comparison between the results of the modified method and experimental measurements is given and discussed in detail.     

变孔径像面散斑平均光强标定随机表面的理论与实验

采用随机表面的高斯相关模型和统计光学原理,推导出弱散射体在4f系统中的像面上光强的表达式.在此基础上提出了均方偏差粗糙度和横向相关长度的标定方法,该方法用理论结果对实验测量的像面散斑平均光强随滤波孔半径的关系曲线进行拟合,同时测量出被测样品表面的两个统计量.实验上制作了高斯相关随机表面样品,对其表面参数进行了测量,与AFM所测结果符合得较好,这表明该方法具有较高的精度. 关键词： 弱散射体 像面散斑 平均光强     

基于平行光管法的薄凸透镜焦距测量

薄凸透镜是光学仪器中最重要、最基本的元件,在天文、军事、医学等众多领域发挥着重要作用。焦距是薄透镜、反射镜等光学系统最重要的特性参量,因而准确测量薄透镜的焦距则显得尤为重要。实验室测量薄凸透镜焦距的方法有物距像距法、自准直法、光电法、平行光管法等。由于采用前3种方法测量透镜焦距的精度偏低,针对该问题,提出利用平行光管法测量薄凸透镜的焦距,并对实验误差作简单分析。实验结果表明,该方法可以高精度地测量薄凸透镜焦距,相对误差仅为0.138%。因此,采用平行光管法的薄凸透镜焦距测量方法是有效可行的。     

容腔调相的单级行波热声发动机起振特性

将容腔结构引入单级环路行波热声发动机系统中进行相位调节,分析了不同容腔位置、容腔内径和容腔长度时系统的起振特性。基于线性热声理论,采用网格传输矩阵数值方法求解系统的起振频率和起振温差;此外,将计算结果与实验结果进行了对比,验证了计算方法的合理性。结果表明:容腔结构可以明显改善系统的起振特性,系统起振温差大幅下降;不同容腔位置处,热机起振特性差异明显;存在最优的容腔内径和容腔长度组合,使得起振温差最低,而容腔尺寸对热机起振频率的影响较小。      

基于双边带调制的频率扫描干涉型激光测距技术

提出并论证了一种基于双边带调制的双扫频干涉测距技术,利用电-光双边带调制产生的-1和+1阶边带分别作为扫描方向相反的两个扫频信号,在接收端各获得一个频率与相对距离相关的拍频信号,通过将这两个拍频信号相乘的方式来减小由光路中扰动引起的测量误差.利用Optisystem软件进行系统仿真,结果表明,该方法能够有效抑制由于光路中扰动产生的测量误差.设计了实验验证系统,在光路中引入小幅振动作为扰动时,该方法对扰动的抑制比超过14dB,有效地提升了测距准确度.     

10m大口径薄膜衍射主镜的色差校正技术研究

分析了薄膜衍射主镜的成像性能及色散特性,利用含有衍射面的反射式消色差光路校正了衍射主镜的强色散,使成像系统的工作波段达到40nm、视场达到0.02°,设计了10m口径、115.73m总长的短结构合成孔径薄膜衍射成像系统.结果表明,消色差光路将两边缘波长0.58μm与0.62μm之间的焦距差由5.34m减小到17.27μm.该研究提供了一种薄膜衍射主镜成像系统的设计方案,可为超大口径薄膜衍射成像系统的工程化研究提供参考.     

靶丸内表面轮廓的白光共焦光谱测量技术

靶丸内表面轮廓是激光核聚变靶丸的关键参数,需要精密检测。本文首先分析了基于白光共焦光谱和精密气浮轴系的靶丸内表面轮廓测量基本原理,建立了靶丸内表面轮廓的白光共焦光谱测量方法。此外,搭建了靶丸内表面轮廓测量实验装置,建立了基于靶丸光学图像的辅助调心方法,实现了靶丸内表面轮廓的精密测量,获得了准确的靶丸内表面轮廓曲线;最后,对测量结果的可靠性进行了实验验证和不确定度分析,结果表明,白光共焦光谱能实现靶丸内表面低阶轮廓的精密测量,其测量不确定度优于0.1μm。     

高功率固体激光器锥形空间滤波孔应用

锥形空间滤波孔是一种应用于高功率固体激光装置空间滤波的新型结构滤波小孔,其内部光滑的锥形结构可以有效滤除光束中的高频成分且避免等离子堵孔现象的发生。根据神光-Ⅲ主机装置结构特点,设计并加工了适用于主机装置的锥形空间滤波小孔,并开展了应用实验研究。通过与传统的平面结构滤波小孔对比可以看出,锥形小孔有效地避免了等离子体度堵孔现象,在与光束波前补偿技术配合使用条件下,保证光束顺利过孔,并成功实现了基频光7988 J的满能量输出。     

TR-LCC中的吸光度

本文指出全内反射长毛细管吸收池(TR-LCC)的最主要特点是有效光路的倍增和测量动态范围的加大,明确定义了有效光路增大比。用简单的分析说明文献[3]中吸光度和浓度、吸收管长度成线性关系的原因,并用计算结果予以让实。说明在感兴趣的范围内,非线性关系是成立的。最后给出一个估算TR-LCC中吸光度的理论上更自洽的公式。     

Photon path length distributions for an isotropically scattering planar medium

The optical path length concept is employed to determine path length distributions by an approximate numerical inversion of the Laplace transform. Six-term or 13-term closed-form representations of the hemispherical reflectance and transmittance optical path length distributions are presented. The mean path lengths and the distributions integrated over path length are found to be in excellent agreement with known results for a scattering optical depth range of 0.001 to 50.0. Any absorption feature of a medium is easily included in a scattering calculation using the results presented. Internal directional heat flux optical path length distributions are shown to exhibit the effects of higher orders of scattering.     

A superresolution optical disk with a combination of optical path filtering and saturable absorption techniques

Calculations have been done for the modulation transfer function of a superresolution optical disk with a combination of optical path filtering and saturable absorption techniques. The results reveal that optical path filtering alone can only equalize, to a certain degree, the spatial frequency response of the opticaldisk system, but it can not attain any response beyond the cutoff frequency. With an additional saturable absorption layer in-between the substrate and the information layer, it is found that the optical response both under and beyond the cutoff frequency can be greatly improved.     

激光干涉测长未对准误差分析

分析了激光干涉测长原理,建立了测长光路中角锥棱镜的光线偏移模型及内部光程模型,推导了忽略直线度误差及角度误差的未对准误差对定位误差测量结果影响关系的简洁表达式,进行了定位误差的测定实验,给出了未对准误差的一种定量评估方法.     

Influence of acoustic leakage at fluid–solid interface on interferometric detection of surface acoustic wave

When using laser interferometer to detect surface acoustic wave at fluid–solid interface, there are two factors which will cause the optical path length variation of the probe laser beam: interface deformation, and refractive index changes in fluid induced by acoustic leakage. Influence of acoustic leakage on laser interferometric detection for surface acoustic wave is researched here. A metal plate immersed in an infinite fluid is used as a physical model. Interface deformation due to laser-induced acoustic wave and pressure in fluid due to acoustic leakage are computed for select cases by finite element method. The optical path length variation caused by the two factors are calculated respectively and compared. The results show that the influence of acoustic leakage increases with the increasing acoustic impedance matching of fluid and solid, the peak-to-peak of influence degree increases linearly with the increasing acoustic impedance of fluid, and that decreasing the distance between the interferometer and interface can effectively reduce the influence of acoustic leakage.     

利于像差校正的共形整流罩内表面面形设计

共形光学系统中,椭球形等厚度整流罩使入射的平行光线经过整流罩后不再平行,变为发散的光线,进而使系统像差急剧增加,不利于后续像差的校正。通过对等厚度共形整流罩的内表面进行重新设计,打破了共形整流罩的等厚度条件,从而在使用较少校正光学透镜的基础上实现了系统像差的校正。通过分析不同级次非球面分别作为整流罩内表面面形时的像差校正效果,确定了将6次非球面作为共形整流罩内表面面形初始结构。通过对内表面进行优化设计,最终得到整流罩内表面面形。结果表明,该方法有效地减小了共形整流罩引入的像差。最后使用固定校正器对内表面变化后的整流罩进行了像差校正,设计结果表明,内表面的改变有效地减少了光学元件数量,消像差效果良好。