ZnO薄膜/金刚石在不同激励条件下声表面波特性的计算与分析

本文首先以刚度矩阵法为基础, 给出了ZnO薄膜/金刚石在四种不同激励条件下的有效介电常数计算公式. 然后以此为工具, 分别计算了多晶ZnO(002) 薄膜/多晶金刚石和单晶ZnO(002) 薄膜/多晶金刚石的声表面波特性, 并根据计算结果及设计制作声表面波器件的要求, 对ZnO膜厚的选择进行了详细地分析. 最后讨论了ZnO/金刚石/Si复合晶片可以忽略Si衬底对声表面特性影响时对金刚石膜厚的要求. 关键词： 声表面波 压电多层结构 有效介电常数 刚度矩阵法     

石英衬底上Au缓冲层对ZnO薄膜微结构的影响

采用单源化学气相沉积(SSCVD)法,在石英衬底上以Au为缓冲层,Zn4(OH)2(O2CCH3)6.2H2O为固相源制备ZnO薄膜。SEM和XRD测试ZnO薄膜的微结构,结果表明:相对于SiO2衬底上生长的ZnO薄膜,Au/SiO2衬底上生长的ZnO薄膜具有较好的结晶质量和表面平整度;对制备ZnO薄膜的衬底温度进行了工艺优化,结果表明:500℃时制备的ZnO薄膜颗粒大小均匀,结晶质量较好;通过荧光光谱仪对Au/SiO2衬底上的ZnO薄膜进行光致发光(PL)谱测试,ZnO薄膜在400nm出现紫光发射峰,而没有出现与缺陷相关的深能级发射峰,表明ZnO薄膜具有较好的结晶质量。     

低温缓冲层对氧化锌薄膜质量的影响

利用金属有机化学气相沉积(MOCVD)法,在Si衬底上外延生长ZnO薄膜。为了改善氧化锌薄膜的质量,首先在Si衬底上生长低温ZnO缓冲层,然后再生长高质量的ZnO薄膜。通过XRD、SEM、光致发光(PL)光谱的实验研究,发现低温ZnO缓冲层可有效降低ZnO薄膜和Si衬底之间的晶格失配以及因热膨胀系数不同引起的晶格畸变。利用低温缓冲层生长的ZnO薄膜的(002)面衍射峰的强度要比直接在Si上生长的ZnO薄膜样品的高,并且衍射峰的半高宽也由0.21°减小到0.18°,同时有低温缓冲层的样品室温下的光致发光峰也有了明显的增高。这说明利用低温缓冲层生长的ZnO薄膜的结晶质量和光学性质都得到了明显改善。     

气相输运法制备ZnO薄膜(英文)

运用气相输运技术在不同的衬底上制备ZnO薄膜,同时对这些ZnO薄膜的表面形貌、晶体结构和光学特性进行表征。在扫描电子显微镜图像上可以看到,相比没有镀金的Si衬底,ZnO纳米颗粒在镀金的Si衬底上的生长尺寸较大。X射线衍射测试结果表明,在Si(111)和Si(100)衬底上生长的ZnO薄膜显示出不同的六角纤锌矿结构的衍射峰,但没有出现立方闪锌矿ZnO结构的衍射峰。在镀金的Si衬底上,ZnO薄膜生长取向主要为c轴方向。此外,所有ZnO样品的光致发光谱上均只出现一个狭窄且强的紫外峰,约在389 nm(3.19 eV)波长处。     

热处理参数对溶胶-凝胶法制备氧化锌薄膜特性的影响

采用溶胶-凝胶旋涂法在Si(111)衬底上生长了ZnO薄膜，并用荧光光谱、原子力显微镜和XRD对ZnO薄膜样品进行了分析.结果表明，溶胶-凝胶旋涂法制备的ZnO薄膜为纤锌矿结构，其c轴取向程度与热处理温度有很大的关系.当热处理温度小于550℃时，氧化锌薄膜在室温下均有较强的紫外带边发射峰，而可见波段的发射很弱；当热处理温度高于550℃时，可见波段发射明显增强.对经过不同时间热处理的ZnO薄膜样品分析表明，氧化锌薄膜的荧光特性及表面形貌与热处理时间也有很大关系，时间过短可见波段的发射较强，但时间过长会导致晶 关键词： ZnO薄膜 光致发光     

MOCVD方法生长的氧化锌薄膜及其发光特性

近年来,随着近紫外光发射氧化锌薄膜研究的进展,许多先进的薄膜生长手段被广泛采用。本文探索了用MOCVD方法在硅衬底上生长氧化锌薄膜的方法,试验了用几种不同的有机金属源生长ZnO薄膜;研究了源材料及生长压力和温度对薄膜生长的影响;观察了样品的室温光致发光光 谱。通过与溅射方法生长的ZnO薄膜的比较,提出了影响材料结构和发光特性的可能原因。     

脉冲激光沉积法在多孔铝衬底上生长的ZnO薄膜的结构与光学性质

ZnO是一种性质优良很有前途的紫外光电子器件材料,多孔铝是一种良好的模板型衬底,试图将二者结合起来以制备出一种全新的光电功能材料。制备了三种不同孔径多孔铝衬底,采用脉冲激光沉积法,在真空背景下,在多孔铝衬底上生长了氧化锌薄膜。利用扫描电子显微镜、X射线衍射和光致荧光对样品进行了测试和分析。研究表明:利用不同孔径的多孔铝衬底生长的氧化锌薄膜的结构和光学性质差异很大。样品A的光致发光主要是394nm的紫外发射和498nm的蓝绿光发射;样品B的光致发光主要是417nm的紫光发射和466nm蓝光发射;样品C的光致发光主要是415nm的紫光发射和495nm的蓝绿光发射。由于薄膜是富锌的,随着在空气中氧化的进行,光谱发生变化。利用固体能带理论对光谱进行了全面的分析。     

表面预处理对氧化锌薄膜质量的影响

用MOCVD方法在c面蓝宝石衬底上生长ZnO薄膜。生长前衬底表面进行预处理,观察不同表面预处理对ZnO薄膜质量的影响。测量氧化锌的XRD谱,观察表面预处理后对氧化锌薄膜结晶质量的影响。室温下用325nm的He-cd激光器作为激发源测量ZnO薄膜的紫外发光谱,观察表面处理后对ZnO薄膜发光特性的影响。用HL5500 Hall System分别对ZnO薄膜的电学特性进行了测试。得到了ZnO薄膜的电阻率和霍尔迁移率,并得到氧气气氛处理后电阻率变小,霍尔迁移率变大;氮气气氛射频处理后电阻率变大,霍尔迁移率变小的结果。     

分子束外延生长的ZnO压电薄膜及其声表面波器件特性

用RF-MBE在蓝宝石(0001)衬底上引入MgO和低温ZnO双缓冲层生长了ZnO薄膜,并制备了声表面波器件。在ZnO薄膜中,仅观测到(0002)面的XRD,且衍射峰增强,半高宽减小,表明ZnO薄膜c轴取向性更好,晶体结构更优。室温下自由激子吸收峰更尖锐和吸收边更陡峭以及仅观测到自由激子发光,且发光线宽变窄、发光强度变大,表明ZnO薄膜缺陷密度减小,薄膜质量提高。测得该ZnO压电薄膜的电阻率高达4×10⁷ Ω·cm,其声表面波的速度高达5 010 m/s。     

氮掺杂氧化锌薄膜的光电特性

采用气体反应电子束蒸发法,氨气氛下在玻璃上沉积了氮掺杂氧化锌(ZnO)薄膜。AFM观察发现氨气氛下生长的氮掺杂氧化锌薄膜表面比未掺杂样品的粗糙度略高,且随氨气压的增加粗糙度也随之增加,这可能与氨气氛对ZnO生长表面的轻微腐蚀作用有关,但表面依然比较平整。XRD分析显示,(0002)衍射峰位没有发生移动,但是氮掺杂后衍射峰的线宽比未掺杂样品稍有增加,衍射峰的半峰全宽由非掺杂ZnO的0.261°增加到0.427°。氧化锌掺氮后电阻率提高了4~7个数量级,达到了降低ZnO中电子浓度的目的。     

The influence of different doping elements on microstructure, piezoelectric coefficient and resistivity of sputtered ZnO film

ZnO film is attractive for high frequency surface acoustic wave device application when it is coupled with diamond. In order to get good performance and reduce insertion loss of the device, it demands the ZnO film possessing high electrical resistivity and piezoelectric coefficient d₃₃. Doping ZnO film with some elements may be a desirable method. In this paper, the ZnO films undoped and doped with Cu, Ni, Co and Fe, respectively (doping concentration is 2.0 at.%) are prepared by magnetron sputtering. The effect of different dopants on the microstructure, piezoelectric coefficient d₃₃, and electrical resistivity of the film are investigated. The results indicate that Cu dopant can enhance the c-axis orientation and piezoelectric coefficient d₃₃, the Cu and Ni dopant can increase electrical resistivity of the ZnO film up to 10⁹ Ω cm. It is promising to fabricate the ZnO films doped with Cu for SAW device applications.     

Propagations of Rayleigh and Love waves in ZnO films/glass substrates analyzed by three-dimensional finite element method

Propagation characteristics of surface acoustic waves(SAWs) in ZnO films/glass substrates are theoretically investigated by the three-dimensional(3D) finite element method. At first, for(11ˉ20) ZnO films/glass substrates, the simulation results confirm that the Rayleigh waves along the [0001] direction and Love waves along the [1ˉ100] direction are successfully excited in the multilayered structures. Next, the crystal orientations of the ZnO films are rotated, and the influences of ZnO films with different crystal orientations on SAW characterizations, including the phase velocity, electromechanical coupling coefficient, and temperature coefficient of frequency, are investigated. The results show that at appropriate h/λ, Rayleigh wave has a maximum k~2 of 2.4% in(90°, 56.5°, 0°) ZnO film/glass substrate structure; Love wave has a maximum k~2 of 3.81% in(56°, 90°, 0°) ZnO film/glass substrate structure. Meantime, for Rayleigh wave and Love wave devices, zero temperature coefficient of frequency(TCF) can be achieved at appropriate ratio of film thickness to SAW wavelength. These results show that SAW devices with higher k~2 or lower TCF can be fabricated by flexibly selecting the crystal orientations of ZnO films on glass substrates.     

Characteristics of SAW UV sensors based on a ZnO/Si structure using third harmonic mode

This paper describes the characteristics of surface acoustic wave (SAW) ultraviolet (UV) sensors fabricated from a ZnO thin film using the third harmonic mode. A ZnO thin film was used as an active layer for UV detection, and a piezoelectric layer was sputtered using magnetron sputtering. The X-ray diffraction (XRD) and photoluminescence (PL) spectra showed that the ZnO sputtered onto Si(100) was highly (002)-oriented and had good optical properties. The two-port SAW resonator was based on an inter-digital transducer (IDT)/ZnO/Si structure and was fabricated and exposed under UV light at a wavelength of 380 nm. As a result, under a UV intensity of 3 mW/cm², the SAW UV sensor was greatly shifted by 400 kHz at the third harmonic mode compared to a frequency shift of 10 kHz in the fundamental mode.     

Two-step sputtered ZnO piezoelectric films for film bulk acoustic resonators

This study investigates high-performance ZnO piezoelectric films used for thin film bulk acoustic resonators (TFBAR). The ZnO piezoelectric film was deposited on a Pt/Ti electrode using an RF magnetron sputter by a two-step method at room temperature. The Pt/Ti electrode was deposited by a DC sputtering system, on which, ZnO piezoelectric films were deposited in one step and in two steps to minimize roughness in the first step and produce the preferred orientation in the second. Both field-emission scanning electron microscopy (FESEM) and atom force microscopy (AFM) revealed that ZnO piezoelectric film deposited by two-step sputtering exhibited favorable characteristics, such as a rigidly precise surface structure with surface roughness of 7.37 nm, even better than in one-step sputtering. Examining the ZnO thin film by X-ray diffraction (XRD) showed a much higher c-axis-preferring orientation than in one-step sputtering. The reflection coefficient of the resonator device was measured using an HP8720 network analyzer. The frequency response of the FBAR device exhibited a return loss of -25 dB at a resonant frequency of 2212 MHz with a high coupling coefficient of 6.7%. PACS 68.55.Jk; 43.35.Ns; 81.15.-z     

The effect of post-annealing on surface acoustic wave devices based on ZnO thin films prepared by magnetron sputtering

Zinc oxide (ZnO) thin films were deposited on unheated silicon substrates via radio frequency (RF) magnetron sputtering, and the post-deposition annealing of the ZnO thin films was performed at 400 °C, 600 °C, 800 °C, and 1000 °C. The characteristics of the thin films were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The films were then used to fabricate surface acoustic wave (SAW) resonators. The effects of post-annealing on the SAW devices are discussed in this work. Resulting in the 600 °C is determined as optimal annealing temperature for SAW devices. At 400 °C, the microvoids exit between the grains yield large root mean square (RMS) surface roughness and higher insertion losses in SAW devices. The highest RMS surface roughness, crack and residual stress cause a reduction of surface velocity (about 40 m/s) and increase dramatically insertion loss at 1000 °C. The SAW devices response becomes very weak at this temperature, the electromechanical coupling coefficient (k²) of ZnO film decrease from 3.8% at 600 °C to 1.49% at 1000 °C.     

溶胶-凝胶法制备氧化锌薄膜的压电行为

"采用溶胶-凝胶技术在单晶硅Si(111)上制备了ZnO压电薄膜,并以扫描电镜、X射线衍射仪(XRD)和原子力显微镜(AFM)进行了表征．XRD衍射实验表明ZnO薄膜随着膜厚的增大,其(002)取向逐渐增强;AFM研究了薄膜的表面形貌、粗糙度与晶粒大小的结果表明,ZnO压电薄膜的粗糙度与晶粒寸随着薄膜厚度的增大而减小．粗糙度为2.188~0.914 nm．利用PFM研究压电系数,发现随着薄膜厚度的增加,(002)生长方向增强,压电系数逐渐增大;当力参数小于薄膜的表面粗糙度时,压电系数测量不准确且在较大幅度     

Tetrahedral amorphous carbon films as a frequency-increasing interlayer of surface acoustic wave devices with a ZnO/Si configuration

Tetrahedral amorphous carbon (ta-C) films deposited using filtered cathodic vacuum arc technology have been applied to the interlayer of surface acoustic wave devices with a ZnO/Si configuration. The phase velocity in the multilayered structure was analyzed in the first instance by theoretical calculations and was then measured by means of a network analyzer. It has been shown that the ta-C interlayer between piezoelectric film and Si substrate can strikingly increase the phase velocity of the surface acoustic wave. The greater the interlayer thickness is and the higher the content of the sp³ hybridization is, the faster surface acoustic wave propagates. However, the increment of phase velocity gradually decreases with increasing interlayer thickness. It was confirmed in this paper that the measured values of the phase velocity as a function of the interlayer thickness agree with the theoretical calculations.     

High frequency SAW devices based on third harmonic generation

We demonstrate the third harmonic generation in a ZnO/Si layered structure to obtain high frequency SAW devices. This configuration eliminates the need of high lithography resolution and allows easy integration of such devices and electronics on the same wafer. A theoretical study was carried out for the determination of the phase velocity and the electromechanical coupling coefficient (K²) dispersion curves of the surface acoustic waves. These results are also in agreement with those measured on a SAW filter designed for the third harmonic generation and the operating frequency is up to 2468 MHz.     

Development of human IgE biosensor using Sezawa-mode SAW devices

This paper reports Sezawa-mode surface acoustic wave (SAW) devices with via-isolated cavity to construct the allergy biosensor. To fabricate Sezawa-mode SAW devices, the RF magnetron sputtering method for the growth of piezoelectric ZnO thin films are adopted and influences of the sputtering parameters are investigated. The optimal substrate temperature of 300 °C, RF power of 120 W and sputtering pressure of 2 Pa were used to deposit piezoelectric ZnO films with a smooth surface, uniform grain size and strongly c-axis-orientated crystallization. A back-etched SAW resonator is used in this study. The wet etching of (100)-oriented silicon wafers is used to form a back-side cavity which is critical to the formation of a hopper cavity for holding bio-analytes. The remaining membrane structure silicon thickness was 25 μm. In this report, the chrome (Cr, 12 nm)/gold (Au, 66 nm) layer was initially deposited onto the sensing area of SAW devices as the binding layer for biochemical sensor. The resonance frequency of the Sezawa-mode SAW device is 1.497 GHz. The maximum sensitivity of the Sezawa-mode is calculated to be 4.44 × 10⁶ cm²/g for human immunoglobulin-E (IgE) detection. The stability for human IgE detection is calculated to be 80% and the variation of the stability ±3% was obtained after several tests.