CsI（TI）晶体中反冲Cs和I核Quenching Factor的测量

许多实验对用CsI(Tl)闪烁晶体作为探测器来寻找和探测暗物质的可行性进行了研究。本工作利用8MeV单能中子轰击CsI(Tl)晶体探测器来研究Cs核和I核的Quenching Factor。在数据处理中，运用脉冲形状甄别（PSD）方法来分辨反冲核信号和本底信号。实验结果表明，在7keV到132keV的能区中，Quenching Factor随着反冲核能量的减少而增加。在探测暗物质的实验中，这一性质对于CsI(Tl)晶体探测器获得较低的能量阈值是很有利的。     

暗物质寻找实验中CsI(Tl)晶体反符合探测器实验研究

一个正在建设的位于韩国Y2L地下实验室的低能暗物质探测实验中, 采用了CsI(Tl)晶体反符合探测器作为主动屏蔽体. 本工作对CsI(Tl)晶体反符合探测器的实验性能进行了研究. 通过FADC系统记录的脉冲波形数据, 研究了探测器的能量分辨率和波形甄别的能力; 研究相同能量γ射线入射到反符合探测器不同位置的相对光输出将有助于选择探测器的工作参数; 为了解晶体自身放射性对暗物质测量的影响, 利用低本底HPGe探测器对CsI(Tl)晶体内部的放射性进行了测量, 得到晶体内部Cs同位素的放射性活度. 探测器系统进行了约18d的试运行取数. 实验数据表明, CsI(Tl)晶体探测器的反符合效率约为31% HPGe探测器的本底计数率水平约为133cpd. 为了进行暗物质探测研究, 需要采取有效的方法进一步降低探测器的本底水平.     

暗物质寻找实验中CsI（T1）晶体反符合探测器实验研究

一个正在建设的位于韩国Y2L地下实验室的低能暗物质探测实验中,采用了CsI（T1）晶体反符合探测器作为主动屏蔽体.本工作对CsI（T1）晶体反符合探测器的实验性能进行了研究.通过FADC系统记录的脉冲波形数据,研究了探测器的能量分辨率和波形甄别的能力;研究相同能量γ射线入射到反符合探测器不同位置的相对光输出将有助于选择探测器的工作参数;为了解晶体自身放射性对暗物质测量的影响,利用低本底HPGe探测器对CsI（T1）晶体内部的放射性进行了测量,得到晶体内部Cs同位素的放射性活度.探测器系统进行了约18d的试运行取数.实验数据表明,CsI（T1）晶体探测器的反符合效率约为31%,HPGe探测器的本底计数率水平约为133cpd.为了进行暗物质探测研究,需要采取有效的方法进一步降低探测器的本底水平.     

X光高分辨探测用CsI(Tl)晶体的蒙特卡罗模拟研究

提出了一种基于CsI(Tl)闪烁晶体和面阵CCD器件、采用光纤和光纤面板进行光耦合及传输、以扇形束线阵扫描方式实现对X光高分辨探测的方案。CsI(Tl)晶体的尺寸大小将直接影响到晶体的发光效率及X光的高分辨探测,据此开展了蒙特卡罗模拟研究。模拟研究了X射线能量、X射线源到探测晶体的距离(源距)、CsI(Tl)晶体的厚度与X射线能量分布、全能峰效率与CsI(Tl)闪烁晶体转换效率之间的关系。结果表明,当X射线能量为120~450 keV,CsI(Tl)晶体尺寸厚度为0~1.5 cm变化时,全能峰效率的变化范围为31.34~96.74%,CsI(Tl)闪烁晶体的转换效率的变化范围为12.8~97.43%。可见,X射线的能量及CsI(Tl)闪烁晶体尺寸的厚度,是决定X光高分辨探测的重要参量,这对优化X光高分辨探测用CsI(Tl)晶体的尺寸设计具有一定的参考价值。     

CsI(Tl)晶体量能器中硅光二极管的核计数器效应研究

研究了由于电磁簇射在CsI(Tl)晶体后端的泄漏而引起的硅光二极管“核计数器”效应. 通过GEANT模拟和实验测量分析其在BESⅢ的CsI(Tl)晶体量能器中对能量测量的影响.     

CsI(Tl)晶体的辐照损伤研究

本文报道CsI(Tl)晶体辐照损伤的实验研究,结果表明,CsI(Tl)晶体具有辐照损伤效应.对被辐照损伤过的CsI(Tl)晶体作恢复研究.表明在200℃下加热4小时,可使辐照操作的CsI(Tl)晶体得到恢复.     

HXMT卫星地面样机成像实验

硬X射线调制望远镜(HXMT)致力于实现硬X射线能段的高灵敏度巡天.HXMT地面样机已在中国科学院高能物理研究所粒子天体物理重点实验室建成.它包括18个栅条准直的NaI(Tl)/CsI(Na)复合晶体探测器,总有效探测面积为5000cm². 探测器工作在20—250keV,视场范围5.7°×5.7°通过近距离放射源成像实验和直接解调成像方法的使用,地面样机能够达到2'点源定位精度和5'角分辨率(FWHM).     

双维位置灵敏CsI(Tl)探测器

描述了一种双维位置灵敏CsI(Tl)探测器.用3组分α源测量该探测器得到的位置分辨为0.81mm(FWHM),对于69MeV/u ³⁶Ar能量分辨为0.9％(FWHM).在RIBLL的ΔE-E粒子鉴别望远镜中常常作为E探测器.由于CsI(Tl)晶体对不同的粒子的能损-光输出的非线性,需要针对不同离子对CsI探测器作能量-光输出校正曲线.     

CsI(Tl)闪烁体软X光能量响应的模拟研究

CsI(Tl)闪烁体是X光转换为可见光比较重要的一个部件,在惯性约束聚变中的X光诊断等方面有着十分重要的应用。通过Geant4软件较为全面地分析了CsI(Tl)闪烁体软X光能量响应,模拟了1~5keV的软X光入射不同厚度(20,30,50μm)CsI(Tl)的能量沉积谱,探究了粒子之间相互作用的物理过程,并比较了不同能量软X光在不同厚度CsI(Tl)闪烁体中的沉积效率。仿真结果表明,随着CsI(Tl)闪烁体厚度的增加,软X光在CsI(Tl)闪烁体中沉积的能量也逐渐增加,沉积效率与CsI(Tl)闪烁体厚度成正比。模拟研究为选择合适厚度的闪烁体做低能段软X光探测实验做铺垫。     

HIRFL-CSR ETF多层CsI(Tl)望远镜探测器能量刻度方法

在兰州重离子加速器冷却储存环（HIRFL-CSR）的外靶终端（ETF）,设计建造了一套多层CsI（Tl）望远镜探测器,用于对轻质量带电粒子的鉴别。这套探测器由7层CsI（Tl）晶体组成,每一层晶体光输出信号由4个光电倍增管分别在晶体4角读出。由于CsI（Tl）晶体对于重离子的响应是非线性的,且与入射离子的种类有关,这些因素使得对这台探测器的能量刻度需要做专门的研究。利用RIBLL2提供的能量在200 s~300 MeV/u的次级束流对探测器进行了测试,并针对第一片CsI（Tl）晶体的光输出以及所有CsI（Tl）晶体光输出的和的刻度方法分别进行了探索。在此能区下,第一片CsI（Tl）晶体猝灭现象可以近似忽略,即光输出与能量沉积近似呈线性。对于所有晶体光输出的和,利用一个经验公式对其进行刻度,利用这种刻度方法计算得到的光输出的值与实验测量值之间的差别小于5%。A multi-layer CsI(Tl) telescope has been designed and constructed at External Target in Facility (ETF) terminal of the Cooling Storage Ring of Heavy Ion Research Facility in Lanzhou(HIRFL-CSR), and is used for identifying light charged particles. The detector consists of seven layers of CsI(Tl) crystals, and the signals of each crystal are read out by four photomultipliers at the corners. Since the response of the CsI(Tl) crystal to the heavy ions is non-linear and also depends on the species of the incident ions, the energy calibration method of the telescope must be carefully studied. With the help of the secondary beams selected by RIBLL2 in the energy ranges from 200 to 300 MeV/u, the telescope has been tested and the energy calibration method for the first-layer crystal together with the whole telescope has been investigated. In this energy region, the quench effect in the first-layer crystal can be neglected and a linear expression can be used to represent the relation between the light output and the energy deposition in the crystal. To the total light output of the telescope, an empirical formula is used for the energy calibration. The difference between the calculated results and the experiment data is globally less than 5%.     

用于暗物质探测实验的CsI(Tl)晶体探测器性能的实验研究

在直接测量暗物质的实验中,反冲核能量的Quenching Factor是一个重要参数.用低能X射线源对一套测量入射中子引起的反冲核能量Quenching Factor的系统进行了能量刻度,得到了这套系统的能量响应关系.PMT单光电子的发射对应于晶体中的能量沉积约为0.32keV.同时研究了不同能量的X射线引起的PMT输出电流信号的积分时间宽度与积分电荷的关系,得到最佳的PMT输出电荷收集条件.     

New limits on interactions between weakly interacting massive particles and nucleons obtained with CsI(Tl) crystal detectors

New limits are presented on the cross section for weakly interacting massive particle (WIMP) nucleon scattering in the KIMS CsI(T?) detector array at the Yangyang Underground Laboratory. The exposure used for these results is 24?524.3 kg·days. Nuclei recoiling from WIMP interactions are identified by a pulse shape discrimination method. A low energy background due to alpha emitters on the crystal surfaces is identified and taken into account in the analysis. The detected numbers of nuclear recoils are consistent with zero and 90% confidence level upper limits on the WIMP interaction rates are set for electron equivalent energies from 3 to 11 keV. The 90% upper limit of the nuclear recoil event rate for 3.6-5.8 keV corresponding to 2-4 keV in NaI(T?) is 0.0098 counts/kg/keV/day, which is below the annual modulation amplitude reported by DAMA. This is incompatible with interpretations that enhance the modulation amplitude such as inelastic dark matter models. We establish the most stringent cross section limits on spin-dependent WIMP-proton elastic scattering for the WIMP masses greater than 20 GeV/c2.     

狭长CsI(Tl)闪烁体发光效率的研究

提出了基于狭长CsI（Tl）闪烁体和面阵CCD器件，采用光纤和光纤面板进行光耦合及传输，以扇形束线阵扫描方式实现对X射线探测与成像的工业X-CT系统探测器方案.基此，通过物理分析及数学建模，利用Matlab模拟研究了X光能量小于450 keV时狭长CsI（Tl）闪烁体的发光效率等性能指标.研究结果表明：当光电吸收截面μph和康普顿吸收截面μc分别为0.000313和0.0000295、反射层反射系数R和衬底反射系数Rs分别取0.95和0.8、荧光线性吸收系数σ取0.000222 μm－1时，得到狭长CsI(Tl)闪烁晶体的长度l、高度h和宽度w取值范围分别是926～4512 μm、242～5000 μm和242～5000 μm的结论.在此范围内，既可使闪烁晶体有较好的空间分辨率又可获得最高的发光效率.     

硬X光弯晶谱仪的定量化标定方法

介绍了具有定量化测量能力的硬X光弯晶谱仪的结构, 利用Mo靶X光管的K特征线作为标定源, 使用绝对标定过的Si(Li)探测器对X光管出射的特征线谱进行强度和谱测量。结合X光管空间分布均匀的特点, 计算进入弯晶谱仪的光子数目, 采取了特征谱扣去轫致谱的计数处理方法, 得到了17 keV和19 keV处弯晶谱仪的绝对效率, 分别为4.3210-4和3.9410-4。     

Simultaneous measurement of ionization and scintillation from nuclear recoils in liquid xenon for a dark matter experiment

We report the first measurements of the absolute ionization yield of nuclear recoils in liquid xenon, as a function of energy and electric field. Independent experiments were carried out with two dual-phase time-projection chamber prototypes, developed for the XENON dark matter project. We find that the charge yield increases with decreasing recoil energy, and exhibits only a weak field dependence. These results are the first unambiguous demonstration of the capability of dual-phase xenon detectors to discriminate between electron and nuclear recoils down to 20 keV, a key requirement for a sensitive dark matter search.     

CsI（Tl）+Si-APD探测器的性能测试

介绍了Si-APD的工作原理并对Si-APD中的暗电流进行了理论分析。基于RIBLL上产生的放射性核束流,使用CsI（Tl）+Si-APD探测器对中能重离子进行了能量测试。测试结果显示,CsI（Tl）+Si-APD探测器测量20 MeV/u的重离子时,可得到3%的能量分辨;同时还发现Si-APD中的暗电流大小以及入射粒子的能量大小都会对探测器的能量分辨产生影响。In this paper, the working principle of Si-APD was introduced and the dark current of Si-APD was analyzed theoretically. The intermediate energy heavy ions, which are produced on the RIBLL(Radioactive Ion Beam Line in Lanzhou), were measured with CsI(Tl)+Si-APD detector. The energy resolution of CsI(Tl)+Si-APD detector is about 3% for heavy ions with energy around 20 MeV/u. It is also found that the energy resolution of detector can be in uenced by the dark current of Si-APD and the energy of incident particles.     

Measure of low radioactive contamination and nuclear recoil quenching factor using cryogenic particle detectors

For double beta decay and dark matter experiments the determination of the radioactive contamination of materials used is of fundamental importance. The cryogenic particle detectors allow the realization of detectors with various types of materials and in this way the radioactivity is measured in a calorimetric approach with very high sensitivity. In particular a new complete analysis for different types of leads, modern and ancient roman, was realized and here presented. The detector sensitivity for a nuclear recoil event is a crucial point in the dark matter experiments. The nuclear recoil detection efficiency for cryogenic particle detectors was directly measured using two TeO₂ crystals facing one with other and performing a coincidence-anticoincidence analysis of the collected data. The determination of the quenching factor for low energy nuclear recoils in the TeO₂ cryogenic detectors shows that these devices are very sensitive to a possible dark matter particle interaction. In cryogenic detectors a nuclear recoil generates signals with the same amplitude of an electron with the same energy. The performed measure and the data analysis will be discussed in detail. Finally the experimental setup and the preliminary test of the new array of TeO₂ cryogenic detectors for double beta decay and dark matter search will be discussed in detail.     

Temperature Effects of CsI(Tl) Crystal Detector with APD Readout

The temperature dependences of the light output of CsI(Tl) crystal grown at IMP and of the gain of the Hamamatsu S8664-1010 avalanche photodiode (APD) have been investigated systematically. The light output of the CsI(Tl) crystal increases with temperature by 0.67%/℃ in the region from －2℃ to 8℃, and by 0.33%/℃ in the region from 8℃ to 25℃, while the gain of the tested APD decreases by －3.68%/℃ (working voltage 400V) on average in the room temperature range. The best energy resolution 5.1% of the CsI(Tl) with APD was obtained for the 662keV γ ray from ¹³⁷Cs radiation source.