水溶性酞菁化合物对有机电致发光器件亮度和效率的影响

以水溶性酞菁铜(CuTcPc)为空穴注入层制备多层有机电致发光器件.ITO表面经过CuTcPc溶液修饰,能够提高空穴的注入能力,增加器件的电流密度和亮度.在有机电致发光器件中,空穴传输材料的空穴迁移率一般大于电子传输材料的电子迁移率,空穴是多数载流子;但是,CuTcPc修饰处理不仅提高了器件的电流密度和亮度,也提高了器...     

基于Spiro-OMeTAD电子阻挡层的量子点发光二极管电荷平衡改善

针对量子点发光二极管空穴传输层和电子传输层的迁移率差异而导致的电荷不平衡问题,将具有最低未占分子轨道高能级的有机聚合物Spiro-OMeTAD薄膜放置在空穴传输层与量子点发光层之间,阻挡过剩电子由量子点发光层向空穴传输层的传输,促进器件的电荷平衡,制备出一种高效的新型绿色量子点发光二极管。结果表明:相比于传统器件,新型绿色量子点发光二极管器件的外部量子效率提升了87%,达到11.87%,亮度提升了106%,达到53055cd/m~2;阻挡过剩电子的传输可以显著改善器件中的电荷不平衡现象。     

不同主体双发光层白色有机电致发光器件的性能研究

制备了结构为ITO/NPB/CBP:TBPe:rubrene/BAlq:Ir(piq)₂(acac)/BAlq/Alq₃/Mg:Ag的白色磷光有机电致发光器件.利用两种不同的主体材料,即用双载流子传输型主体材料CBP掺杂荧光染料TBPe及rubrene作为蓝光和橙黄光发光层;用电子传输型主体材料BAlq掺杂磷光染料Ir(piq)₂(acac)作为红色发光层.以上双发光层夹于空穴传输层NPB与具有电子传输性的阻挡层BALq之间.讨论了如何控制     

基于新型电荷生成层的P-i-N结构白色有机叠层电致发光器件

采用2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP): 5 wt.% cesium carbonate(Cs₂CO₃)和N, N'-Bis(naphthalen-1-yl)-N,N'-bis(phenyl)-benzidine(NPB): 20 wt.% molybdenum oxide(MoO₃)分别作为器件的电子注入层和空穴注入层,研究了N型和P-i-N结构有机电致发光器件的载流子传输特性.载流子传输层中BCP: Cs₂CO₃和NPB:MoO₃的引入有效增强了载流子注入能力,从而降低了器件的驱动电压.基于新型电荷生成层BCP: 5 wt.% Cs₂CO₃/ NPB: 20 wt.% MoO₃制备了色稳定、高效率P-i-N结构有机叠层器件.与单元器件相比,引入新电荷生成层有机叠层器件的最大电流效率增大了2.5倍,表明该电荷生成层可以有效地将电子和空穴分别注入到相邻发光单元中.采用该电荷生成层制备了P-i-N结构白色有机叠层器件,器件的上下发光单元分别为橙光和蓝光发射.当发光亮度从500增加到5 000 cd/m²时,器件的色坐标稳定在(0.33, 0.29)附近,接近白光等能点.利用单色发光单元堆叠制备白色有机叠层器件的方法为实现色稳定、高效率的白色有机电致发光器件提供了一种有效的途径.     

温度对单层有机电致发光器件电流平衡因子的影响（英文）

考虑有机薄膜中的陷阱,建立单层双极性有机发光器件的电学模型,研究了在不同的载流子迁移率和注入势垒条件下,器件工作温度对器件电流平衡因子的影响.研究表明:在低温工作区,当电子注入势垒和空穴注入势垒相等时,器件的电流平衡因子最大;在高温工作区,当电子迁移率大于空穴迁移率时,若电子注入势垒大于空穴注入势垒,器件的电流平衡因子最大,而当电子迁移率小于空穴迁移率时,情况恰好相反;当电子迁移率等于空穴迁移率时,电子注入势垒和空穴注入势垒相等时器件的电流平衡因子最大.此外,器件的电流平衡因子随着器件工作温度的升高而逐渐增大.可对设计高性能有机发光器件提供一定的理论参考.     

单层有机器件的电子传输特性的数值模拟

在漂移扩散模型的基础上建立了单层有机器件的模型,包括了电荷注入、传输、空间电荷效应和陷阱的影响.电荷注入考虑了热电子发射电流和隧道电流.模拟得到的结果和文献中报道的实验测试数据一致.模拟研究了各个因素对器件J-V曲线的影响,电流和器件长度成反比,电流随着空穴注入势垒的减小而增加.电子注入势垒从1.7 eV减少到0.5 eV时,电流随着电子注入势垒的减小而减小,这主要是因为有机材料中电子迁移率太小,电子注入电流的增加可以忽略,而电子注入势垒的减小使内建势增加,在同样的电压下,场强 关键词： 有机器件 传输特性 数值模拟     

利用p型掺杂技术制备的高效有机电致发光器件

利用氧化钼(MoO_x)作为p型掺杂剂,以掺杂层4,4'-bis(carbazol-9-yl)biphenyl(CBP):MoO_x作为空穴注入层,制备了一种结构为ITO/MoO_x/CBP:MoO_x/CBP/CBP:tris(2-phenylpyridine)iridium(III)(Ir(ppy)₃)/4,7-diphenyl-1,10-phenanthroline(Bphen)/LiF/Al的有机电致发光器件.器件中CBP同时作为空穴注入层、空穴传输层以及发光层母体材料,这种结构具有结构简单同时能有效降低空穴注入势垒等优点.研究发现,随着空穴注入层厚度的增加,器件的电流密度增加,表明p型掺杂层的引入能够有效增强空穴的注入;通过优化器件空穴注入层与空穴传输层厚度,器件性能有所提高,最大电流效率为29.8 cd/A,可以认为合理的优化空穴注入层和空穴传输层的厚度,使载流子在发光层中的分布更加平衡是提高器件发光效率的主要原因.值得指出的是,从电流效率最大值到亮度为 20 000 cd/m²时,优化后器件的效率衰减仅为17.7%,而常规器件的效率衰减则为62.1%,优化后器件效率衰减现象得到了明显的改善.分析认为优化后的器件中未掺杂的CBP有助于展宽激子形成区宽度,进而减弱了三线态-三线态湮灭、三线态-极化子淬灭现象,激子形成区的展宽是改善效率衰减的主要原因.     

窄谱带绿色有机电致发光器件

以Tb³⁺:水杨酸(Tb³⁺:(SA)₃)为空穴传输层兼发光层、高荧光材料Alq₃为电子传输层,得到了窄谱带的绿色有机薄膜电致发光双层结构器件.实验证实,双层器件的电致发光是电荷载流子隧穿内界面(Tb³⁺:(SA)₃/Alq₃)之后分别在两有机层内的复合发光,是两有机层本征发光的叠加.其光谱随着电子传输层厚度而改变,因而减少电子传输层厚度能得到亮度高、稳     

载流子迁移率对单层有机发光二极管复合效率的影响

建立了在单层有机发光二极管中电场强度不太大(E≤104Vcm)的情况下,载流子注入、传输和复合的理论模型.通过求解非线性Painleve方程得出了电场强度随坐标变化的解析函数关系式以及电流密度随电压变化关系,给出了电流密度以及器件的复合效率在不同的载流子迁移率情况下随电压变化关系图像.结果表明,复合效率受载流子迁移率影响较大,在器件中多数载流子应具有较低的迁移率,而少数载流子应具有较高的迁移率,这样有利于载流子的注入和传输,从而可提高发光效率.并且得出当空穴迁移率大于电子迁移率时,复合区域偏向阴极,反之亦 关键词： 单层有机发光二极管 复合效率 迁移率     

混合发光层有机电致发光器件中的多重成分发射

以等摩尔空穴传输材料TPD和电子传输材料PBD组成结构为ITO/TPD/TPD∶PBD/PBD/Al的混合物发光层有机电致发光(EL)器件,观察到了相对于组成材料的荧光光谱红移的宽发射带。通过比较EL光谱,光致发光光谱及EL光谱分解,表明电致发光中同时包含单体发射、激基复合物和电荷对复合物的发射。激基复合物为TPD的激发态TPD*与PBD的基态相互作用形成TPD*PBD类型的复合物,电荷对复合物是带电荷的空穴传输分子(D+)的空穴和电子传输分子(A-)的电子交叉复合而形成的(D+-A-)*复合物。各激发态在电场作用下呈现不同的形成机理和复合过程,并且单体发射和激发态复合物的比例随电场而变化,导致发射光谱随电场增强而蓝移。该器件的最高亮度和最大外部量子效率分别为240 cd·(cm2)-1和0.49%。有机固态界面激基复合物或电荷对复合物的发射常出现宽的红移发射带,是调节发光颜色的有效手段。     

Effect of solvents on the performance and morphology of polymer photovoltaic devices

In the polymer photovoltaic devices (PVDs), the performance of devices was strongly influenced by region-regularity, number average molecular weight and casting solvents of polymers. In this work, we fabricated p–n bulk-hetero-junction PVDs based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C₆₀-butyric acid methyl ester (PCBM) using various solvents such as chloroform (CF), chlorobenzene (CB), dichlorobenzene (DCB), and mixed solvent (CF/CB, CF/DCB). Thin film of active layer with P3HT/PCBM was prepared by spin coating and thermal annealing at 150 °C with fixed thickness about 110 nm by adjusting solution concentration. The crystalline morphology and layered phase for the active layer were studied by atomic force microscopy and X-ray diffraction, respectively. We investigated the performance of solar cells according to different morphology and crystallinity of active layer by various solvent and mixed solvent.     

Field-effect transistor structures on the basis of poly(3-hexylthiophene), fullerene derivatives [60]PCBM, [70]PCBM,and nickel nanoparticles

Organic field-effect transistor (OFET) structures with the active layers on the basis of composite films of semiconductor polymer poly(3-hexylthiophene) (P3HT), fullerene derivatives [60]PCBM, [70]PCBM, and nickel (Ni) nanoparticles are obtained, and their optical, electrical, and photoelectrical properties are studied. It is shown that introducing Ni nanoparticles into P3HT: [60]PCBM and P3HT: [70]PCBM films leads to an increase in the absorption and to quenching of photoluminescence of the composite in the 400–600 nm spectral band due to the plasmon effect. In P3HT: [60]PCBM: Ni and P3HT: [70]PCBM: Ni OFET structures at the P3HT: [60]PCBM and P3HT: [70]PCBM concentrations of ~1: 1 and Ni concentrations of ~3–5 wt %, current–voltage (I–V) characteristics typical of ambipolar OFETs with the dominant hole conduction are observed. The charge-carrier (hole) mobilities calculated from the I–V characteristic at V_G =–10 V were found to be ~0.46 cm²/(V s) for P3HT: [60]PCBM: Ni and ~4.7 cm²/(V s) for P3HT: [70]PCBM: Ni, which means that the mobility increases if [60]PCBM in the composition is replaced with [70]PCBM. The effect of light on the I–V characteristics of P3HT: [60]PCBM: Ni and P3HT: [70]PCBM: Ni OFETs is studied.     

二甲基亚砜添加剂对聚合物太阳能电池性能的影响

研究了二甲基亚砜(DMSO)掺杂浓度对基于聚(3-己基噻吩)(P3HT)和(6,6)-苯基碳60丁酸甲酯(PCBM)为有源层的聚合物太阳能电池性能影响。结果表明,掺杂DMSO可以提高聚合物太阳能电池短路电流密度和填充因子。DMSO掺杂质量比为3%时,电池短路电流密度提高到7.88 mA·cm-2,填充因子为55.5%。能量转换效率达到2.54％,相比没有掺杂DMSO的电池,能量转换效率提高了17%。傅里叶变换红外光谱被用于鉴定和分析掺杂DMSO对材料P3HT∶PCBM化学性质的影响。傅里叶变换红外光谱表明,掺杂后P3HT和PCBM的化学性质都没有改变。为分析掺杂DMSO改善器件能量转换效率的原因,通过紫外-可见光谱和电流密度-电压特性曲线分别表征器件的光吸收能力以及电致发光器件的载流子迁移率。与P3HT∶PCBM薄膜相比,P3HT∶PCBM∶DMSO薄膜在可见光范围内的吸收峰有明显红移且吸收强度增强。可见光吸收的改善是实现短路电流密度提高的有力保障。太阳能电池性能的增强是因为DMSO的掺杂提高了P3HT∶PCBM的载流子迁移率和吸收光谱宽度。     

Preheated solvent exposure on P3HT:PCBM thin film: A facile strategy to enhance performance in bulk heterojunction photovoltaic cells

In this study, we explored the ability of a preheated solvent (methanol) to induce characteristic changes at the organic active layer/metal interface, thereby improving the performance of fabricated organic photovoltaic (OPV) cells composed of poly(3-hexylthiopene) (P3HT) and a [6,6]-phenyl-C₇₁-butyric acid methyl ester (PCBM) photoactive blend. Our results demonstrate that exposure to methanol (at room temperature, or preheated at 45 °C or 65 °C) improves the performance of the fabricated OPV cells. After preheated methanol exposure, the P3HT:PCBM thin films were tested for crystallinity, morphology, mobility, and photovoltaic characteristics. Our results revealed that use of the preheated solvent on the organic active layer significantly influences the micro/nano scale morphology and phase segregation of the P3HT:PCBM thin films, as well as the charge carrier mobility. It is hypothesized that the side chain ordering of P3HT and redistribution of PCBM could be results of the modified active layer. Consequently, OPV cells modified with the methanol preheated at 65 °C exhibited a power conversion efficiency (PCE) of 3.36%, with open-circuit voltage of 0.59 V, short-circuit current density of 13.83 mA/cm², and fill-factor of 0.41. In contrast, the unmodified P3HT:PCBM thin film (without methanol exposure) showed a PCE of only 2.13%.     

Influence of fullerene derivative replacement with TiO2 nanoparticles in organic bulk heterojunction solar cells

In an effort to develop hybrid organic solar cells with improved power conversion efficiency (PCE), devices based on poly (3-hexylthiophene) (P3HT):phenyl C₆₁-butyric acid methyl ester (PCBM) active layer and poly (3,4-ethylenedioxythiophene) (PEDOT):poly (styrenesulfonate) (PSS) buffer layers were prepared. A systematic replacement of PCBM was achieved by introducing nanostructured TiO₂ (∼15 nm particle size), dissolved separately in chlorobenzene (CB) and 1,2 –dichlorobenzene (DCB), to the (P3HT:PCBM) active layer while keeping a fixed amount for P3HT. To understand the effect of fullerene replacement with the inorganic metal oxide nanoparticles on different properties of resulting devices, a variety of techniques such as Current–Voltage (J–V) characteristics, Field Emission Scanning Electron Microscopy (FESEM), Atomic Force Microscopy (AFM), Ultravoilet-Visible (UV–Vis) Spectrophotometry and External Quantum Efficiency (EQE) were employed. The addition of TiO₂ nanoparticles in the active layer improved the power conversion efficiency (PCE) of P3HT:PCBM devices. The addition of TiO₂ nanoparticles using CB as solvent enhanced the absorption in visible region and also introduced a red shift in the absorption spectra. A significant increase in EQE was observed for devices with TiO₂ nanoparticles in the active layer. Mixing TiO₂ also increased the surface roughness of the active layer where TiO₂ nanoparticles were found to agglomerate as their concentration increased relative to fullerene derivative. A complete agglomeration of TiO₂ was observed in the absence of PCBM.     

Charge transport in polythiophene:fullerene:nanotube bulk heterojunction photovoltaic devices investigated by impedance spectroscopy

P3HT:PCBM bulk heterojunction devices incorporating SWNTs, which are predominantly metallic in character, have been analyzed using impedance spectroscopy to understand the effect of SWNTs on their charge carrier transport properties. SWNTs reduce the effective lifetime of injected charge carriers. Frequency dependence of capacitance and conductance of P3HT:PCBM devices show monotonic variations without any clear peak positions. Simulations of the complex admittance of the P3HT:PCBM devices under trap free space charge limited current within the framework of Scher–Montrol theory are used to qualitatively show that such characteristics are a signature of charge transport which is highly dispersive in nature. The position of peak τ_peak in the imaginary part of impedance Im(Z), which is essentially same as the first transition frequency of Cole–Cole plot, has a direct relation with the effective dc mobility of charge carriers which varies with dispersion parameters. Using the dc mobility values and the voltage variation of peak frequency of Im(Z), the ratio of τ_dc to τ_peak has been calculated. The magnitude of this ratio is indicative of the degree of dispersiveness in transport. It has been shown that, SWNTs at low concentrations tend to reduce the dispersiveness in charge transport.     

The effect of post-annealing on the interface between the aluminum electrode and the active layer in polymer/fullerene solar cells

The post-annealing effects on the performance of poly (3-hexylthiophene) (P3HT)/(6,6)-phenyl C₆₁ butyric acid methyl ester (PCBM) solar cells with conventional bulk heterojunction (CBHJ) and layer-evolved bulk heterojunction (LBHJ) have been compared. It is found that contrary to the much better performance obtained from CBHJ cells, the post-annealing deteriorates the performance of LBHJ devices. Aqueous contact angle and X-ray photoelectron spectroscopy measurements show that P3HT is dominant at the top surface of CBHJ film, while PCBM is dominant at the top surface of LBHJ film. The micron-scale morphology evolution of the active layer/Al interface upon post-annealing reveals that the PCBM-rich surface is beneficial for the nucleation and growth of PCBM crystal, which does harm to the contact between the active layer and the electrode and results in the decrease of the fill factor. However, the original P3HT-rich surface prevents the formation of large surface-segregated PCBM clusters upon post-annealing, which is highly desirable for the efficient polymer/fullerene solar cells.     

三元P3HT:PTB7-Th:PCBM聚合物太阳能电池性能的研究

将窄带隙聚合物PTB7-Th作为第三种物质掺入到P3HT:PCBM中制备了双给体结构的三元聚合物太阳能电池, 并且通过改变PTB7-Th的浓度来研究PTB7-Th对器件性能的影响. 研究发现, 掺入PTB7-Th后, 聚合物太阳能电池的短路电流和填充因子同时获得了提高, 使器件的光电转换效率得到了改善. 进一步分析表明, PTB7-Th的加入能够拓宽活性层的吸收光谱, 增加活性层吸收的光子数目, 有利于短路电流的提升. PTB7-Th与P3HT之间以电荷转移的形式相互作用, 这种作用方式有利于激子的解离, 从而使器件的填充因子得到了提高.     

Post-fabrication annealing effects on the performance of P3HT:PCBM solar cells with/without ZnO nanoparticles

In this study, P3HT:PCBM organic photovoltaic (OPV) devices, with or without ZnO nanoparticles buffer layer between the photoactive layer (P3HT:PCBM) and the cathode (Al top electrode), were fabricated. The devices were annealed at 145 °C either before or after depositing the top electrode. The objective of this study was to investigate the effects of the ZnO buffer layer and pre-/post-fabrication annealing on the general performance of these devices. The short-circuit current density (J_SC), open-circuit voltage (V_OC) and the external quantum efficiency (EQE) of the OPV devices were improved by the insertion of the ZnO layer and post-fabrication annealing. The post-fabrication annealed devices, with or without the ZnO layer, exhibited higher values of J_SC, V_OC and EQE than those of similar devices annealed before depositing the Al metal. This can be attributed to, among other things, improved charge transport across the interface between the photoactive layer and the Al top electrode as a result of post-annealing induced modification of the interface morphology.     

Effect of slow-solvent-vapour treatment on performance of polymer photovoltaic devices

In this work, enhanced poly(3-hexylthiophene):[6,6]-phenyl-C61-butyric acid methyl ester (P3HT:PCBM) bulkheterojunction photovoltaic devices are achieved via slow-solvent-vapour treatment. The correlations between the morphology of the active layer and the photovoltaic performance of polymer-based solar cell are investigated. The active layers are characterized by atomic force microscopy and optical absorption. The results show that slow-solventvapour treatment can induce P3HT self-organization into an ordered structure, leading to the enhanced absorption and efficient charge transport.