Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉，并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4相似文献}   

Eu2+, Cr3+共掺杂的MAl12O19 (M=Ca, Sr, Ba) 的发光性质及能量传递

三基色荧光粉中, 红色荧光粉性能较差, 为获得性能优良的红色荧光粉, 本文采用高温固相法合成了Eu²⁺, Cr³⁺单掺杂及共掺杂的碱土金属多铝酸盐MAl₁₂O₁₉ (M =Ca, Sr, Ba) 发光体. 实验表明, 在以上三种基质中均存在Eu²⁺→Cr³⁺的能量传递, 利用能量传递可以有效将Eu²⁺的蓝光或绿光转换为红光. 三种碱土金属多铝酸盐基质的晶体结构相似,但Eu²⁺, Cr³⁺发光受晶体场影响,导致在不同的基质中Eu²⁺, Cr³⁺间能量传递效率不同.通过光谱分析及能量传递效率计算发现, 相同掺杂浓度下,CaAl₁₂O₁₉中Eu²⁺→Cr³⁺的能量传递效率最高,SrAl₁₂O₁₉次之, BaAl₁₂O₁₉最低.红光转换率在CaAl₁₂O₁₉中最高.     

用于白光LED的单一基质白光荧光粉Ca2SiO3Cl2:Eu2+，Mn2+的发光性质

用高温固相法合成了Eu²⁺，Mn²⁺共激活的Ca₂SiO₃Cl₂高亮度白色发光材料，并对其发光性质进行了研究. 该荧光粉在近紫外光激发下发出强的白色荧光，Eu^{2+中心形成峰值为419 nm和498 nm的特征宽带，通过Eu2+中心向Mn2+中心的能量传递导致了峰值为578 nm的发射，三个谱带叠加从而在单一基质中得到了白光. 激发光谱均分布在250—415 nm的波长范围，红绿蓝三个发射带的激发谱峰值分别位于385 nm，412 nm，370 nm和396 nm处，可以被InGaN管芯产生的紫外辐射有效激发. Ca₂SiO₃Cl₂:Eu2+，Mn2+是一种很有前途的单一基质白光LED荧光粉.}     

SiN掺杂提高BaMgAl10O17:Eu2+荧光粉光学性能的第一性原理研究

使用基于密度泛函理论的CASTEP软件计算了BAM:Eu²⁺(BaMgAl₁₀O₁₇:Eu²⁺)荧光粉在SiN掺杂前后的能带、态密度、吸收光谱和Mulliken布居．Eu²⁺处于BR位置光吸收更强;SiN掺杂使处于BR位置的Eu²⁺的数量上升,而处于mO位置的Eu²⁺的数量下降,抵消了SiN掺杂降低Eu的态密度对光谱的影响．所以适量掺杂的SiN提高了BAM:Eu²⁺荧光粉的吸收发射光谱强度．Si-N键和Eu-N键的Mulliken布居数分别高于Al-O键和Eu-O键, 说明Si-N键和Eu-N键的共价性分别强于Al-O键和Eu-O键．发光中心Eu²⁺局域结构共价性的增强降低了BAM:Eu²⁺镜面层的活性,这是SiN掺杂提高BAM:Eu²⁺+荧光粉光学稳定性的主要原因．     

Dy3+/Nd3+掺杂对Sr4Al14O25:Eu2+陷阱能级的影响

采用高温固相法合成了Sr₄Al₁₄O₂₅: Eu²⁺,Sr₄Al₁₄O₂₅: Eu²⁺,Dy³⁺和Sr₄Al₁₄O₂₅: Eu²⁺,Nd³⁺材料,研究了Dy³⁺或Nd     

La2Zr2O7:Eu3+纳米棒的合成、表征及其荧光性能

采用传统固相法和水热法成功地制备出棒状La₂Zr₂O₇:Eu³⁺荧光粉. 利用X射线粉末衍射仪、透射电镜和荧光光谱仪等分析了产物的结构、形貌和发光特性. 结果表明红色荧光粉La₂Zr₂O₇:Eu³⁺有良好的晶相,属于立方结构,空间点群为Fd3m; 其形貌主要为纳米棒, 平均直径约47 nm, 长度为50～700 nm. 并对纳米棒的生长机理进行了探讨. 在466 nm蓝光激发下,La₂Zr₂O₇:Eu³⁺荧光粉能发射出Eu³⁺的特征红色荧光,发射主峰位于616 nm处,归属于Eu³⁺的⁵DO_→⁷F2_{超灵敏电偶极跃迁.此外,在产物的发射光谱中能够观察到⁵D}1_→⁷FJ _{(J=0, 1, 2)跃迁和⁵D}1_→⁷FJ _{(J=1, 2, 4)跃迁的劈裂峰,这说明Eu³⁺处在低对称性的晶体场格位中.}     

Gd2O3:Eu3+纳米晶的燃烧合成及光致发光性质

采用柠檬酸作燃烧剂用燃烧合成法制备了Gd₂O₃:Eu³⁺纳米晶.用X射线衍射仪(XRD)、高分辨透射电子显微镜(HRTEM)和荧光分光光度计等对Gd₂O₃:Eu³⁺纳米晶的结构、形貌和发光性能进行了分析.结果表明：不同柠檬酸与稀土离子配比(C/M)制备的样品经800℃ 退火1 h后，均得到了纯立方相的Gd₂O₃:Eu³⁺纳米晶，晶粒尺寸约为30 nm，尺寸分布较窄，其中以C/M=1.0时制备的纳米晶结晶性最好，发光强度最大.Gd₂O₃:Eu³⁺纳米晶主发射峰位置均在612 nm处 (⁵D₀→⁷F₂跃迁)，激发光谱中电荷迁移态发生红移，观察到Gd³⁺向Eu³⁺的有效能量传递.对柠檬酸与稀土离子配比(C/M)对结晶度、发光性质等的影响也进行了分析和讨论.     

光谱探针法确定Eu3+:ThO2的格位对称性及选择激发下样品的光致发光研究

测量和分析了不同温度下Eu³⁺:ThO₂的激发光谱、发射光谱和荧光 衰减曲线.Eu³⁺:ThO₂晶体是用熔融法生长的.通过12K下格位选择激 发下的发射光谱测量,利用晶场理论,确定了Eu³⁺在ThO₂占据Oh和C_3v两种格位.列表给出了两种格位Eu³⁺离子的晶场能 级和室温及12K下的荧光寿命.讨论了温度对能     

新型光存储材料Sr2SnO4: Tb3+, Li+ 的合成及其红外上转换光激励发光性能的研究

采用高温固相法获得了一种只具有 微弱余辉的新型电子俘获型光存储材料Sr₂SnO₄:Tb^{3 +}, Li ⁺. 发光性能研究结果表明: 该材料对980 nm的红外激光具有很好的上转换光激励信息读出响应, 同时292 nm紫外光为其最佳信息写入光源. 光存储性能研究结果表明: 该材料的浅陷阱较少, 因此其余辉发光很弱, 不到500 s; 另一方面, 该材料中存在大量的深蓄能陷阱. 因此, Sr₂SnO₄: Tb^{3 +}, Li⁺是一种具有较好实际应用价值的新型电子俘获型光存储材料. 此外, 还讨论了Sr₂SnO₄: Tb^{3 +}, Li⁺的光存储发光机理.     

LD抽运Er3+，Yb3+共掺磷酸盐玻璃被动调Q激光器的理论分析和数值计算

研究了以Co²⁺:MgAl₂O₄晶体为饱和吸收体的LD抽运Er³⁺,Yb³⁺共掺磷酸盐玻璃激光器.针对双掺离子之间的能量传递和Er³⁺的多种跃迁过程，结合Co²⁺:MgAl₂O₄晶体中Co²⁺离子的饱和吸收特性，给出了详尽的速率方程，在其基础上进行了数值分析，分析了输出镜透过率、激光介质长度、谐振腔长度、腔内往返损耗、饱和吸收体长度对激光阈值、峰值功率、单脉冲能量以及脉冲宽度的影响.     

P掺杂对绿色荧光粉BaMgAl$lt;sub$gt;10$lt;/sub$gt;O$lt;sub$gt;17$lt;/sub$gt;:Mn$lt;sup$gt;2+$lt;/sup$gt;性能的影响

采用高温固相法合成P掺杂的BaMgAl₁₀O₁₇:Mn²⁺荧光粉,其中P通过（NH₄）₂HPO₄引入.利用X射线衍射谱、傅里叶变换红外光谱、扫描电子显微镜、能量色散谱、真空紫外光谱等研究了P掺杂对BaMgAl₁₀O₁₇:Mn²⁺晶体结构、微观形貌、发光性能等的影响.研究结果表明：（NH₄）₂HPO₄具有助熔剂的作用,它的加入有助于荧光粉的晶化,改善荧光粉的形貌.P掺杂进入晶格,使得晶胞参数变小,从而改变了Mn²⁺的晶体场环境,引起发射光谱蓝移,色坐标x值降低.P掺杂能有效提高基质对真空紫外线的吸收,从而提高真空紫外激发下的发光强度. 关键词： P掺杂 10O₁₇:Mn²⁺')" href="#">BaMgAl₁₀O₁₇:Mn²⁺ 晶体结构 真空紫外     

Characterization of host-lattice emission and energy transfer in BaMgAl10O17:Eu

Host-lattice emission, energy transfer and degradation processes are characterized in undoped and Eu-doped BaMgAl₁₀O₁₇. Undoped BaMgAl₁₀O₁₇ exhibits a broad emission centered at 265 nm when excited at wavelengths shorter than 190 nm. This emission is assigned to exciton recombination at Ba-O groups in the cation layer of the lattice. The emission exhibits excellent overlap with the excitation band of Eu²⁺ in this host, providing a means of host-to-activator energy transfer in the doped phosphor. The exciton emission is relatively stable to thermal damage, but undergoes a peak shift and significant decrease in intensity after exposure to VUV radiation. Heating of VUV-damaged materials in air leads to some repair of the spectral properties.     

Eu2+,Mn2+在BaZnP2O7中的发光及Eu2+→Mn2+能量传递

采用高温固相法合成了BaZnP₂O₇:Eu²⁺,Mn²⁺荧光粉,并对其发光性质及Eu²⁺对Mn²⁺的能量传递机理进行了研究.Eu²⁺和Mn²⁺在380 nm和670nm的发射峰分别由Eu²⁺的5d—4f跃迁和Mn²⁺的⁴T₁(^{4关键词： 磷酸盐 2+}')" href="#">Eu²⁺ 2+')" href="#">Mn²⁺ 能量传递     

Novel green-emitting Na2CaPO4F:Eu phosphors for near-ultraviolet white light-emitting diodes

In this study, green-emitting Na₂CaPO₄F:Eu²⁺ phosphors were synthesized by solid-state reactions. The excitation spectra of the phosphors showed a broad hump between 250 and 450 nm; the spectra match well with the near-ultraviolet (NUV) emission spectra of light-emitting diodes (LEDs). The emission spectrum showed an intense broad emission band centered at 506 nm. White LEDs were fabricated by integrating a 390 nm NUV chip comprising blue-emitting BaMgAl₁₀O₁₇:Eu²⁺, green-emitting Na₂CaPO₄F:0.02 Eu²⁺, and red-emitting CaAlSiN₃:Eu²⁺ phosphors into a single package; the white LEDs exhibited white light with a correlated color temperature of 5540 K, a color-rendering index of 90.75, and color coordinates (0.332, 0.365) close to those of ideal white light.     

Emission properties of Eu, Mn in MAl2Si2O8 (M=Sr, Ba)

The emission properties of Eu²⁺ and Mn²⁺ in monoclinic SrAl₂Si₂O₈ (M-SAS) and hexagonal BaAl₂Si₂O₈ (H-BAS), both of which have only one alkaline-earth site, were studied. The emission peaks of both Eu²⁺ (405 nm) and Mn²⁺ (564 nm) in SrAl₂Si₂O₈, are located at longer wavelengths, compared with those in H-BAS (373 nm for Eu²⁺ and 518 nm for Mn²⁺), because of the stronger crystal field strength at the Sr site. EPR spectra showed that the g values of Mn²⁺ are 4.5065 in M-SAS:Mn and 2.0247 in H-BAS:Mn. Magnetic measurements proved that Mn²⁺ was at high-spin state in both hosts. The large g value of Mn²⁺ in M-SAS was ascribed to the mixing of the first excitation state to the ground state, both of which have lower d orbital degeneracy due to the lower symmetry of Mn²⁺ site. The transfer efficiency from Eu²⁺ to Mn²⁺was about 10% in M-SAS, higher than that in H-BAS (5%). This was probably because Eu²⁺ emission overlaps the relatively low excitation level of Mn²⁺ in M-SAS. In order to obtain high transfer efficiency, it was necessary for the Eu²⁺ emission to overlap the lowest excitation level of Mn²⁺. The results obtained in this work may be helpful to design the new white or red phosphors for white-light emitting diode (w-LED) applications.     

Thermoluminescence spectroscopy of Eu and Mn doped BaMgAl10O17

Thermoluminescence (TL) studies of Eu²⁺ and Mn²⁺ doped BaMgAl₁₀O₁₇ (BAM) are reported and discussed. The TL spectra that are measured after irradiation with ultraviolet (120-) show a series of TL peaks between 100 and . The TL spectra are similar for BAM with the two dopants, which suggest that the shallow traps are typical for the BAM host lattice. Using the Hoogstraaten analysis trap depths between 0.1 and are determined. A model is proposed based on thermally activated recombination in local TL centres (not via the conduction band). Further support for this model is obtained from the observation that the TL signal is strongest for excitation around the band edge of BAM . Upon heating the samples in air all low temperature TL peaks decrease in intensity. In addition a new peak appears in the TL spectrum, which is connected with a deeper trap and also a partial oxidation of Eu²⁺ to Eu³⁺ is observed. The luminescence efficiency is lower and the UV induced degradation is faster after annealing in air. These results indicate that the shallow traps are related to oxygen vacancies. The shallow traps do not have a negative influence on performance (efficiency and degradation) of BAM as a lighting phosphor. The luminescence efficiency and stability are strongly influenced by the formation of Eu³⁺ and a deeper trap during annealing in air. Subsequent annealing in a reducing atmosphere restores the original properties.     

Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.     

The ultraviolet irradiation degradation of fluorescent lamp used BaMgAl10O17:Eu2+,Mn2+ phosphor

The ultraviolet irradiation degradation of lamps using BaMgAl₁₀O₁₇:Eu²⁺,Mn²⁺ phosphor is investigated. The X-ray photoelectron spectra demonstrate that the oxidation of Eu²⁺ is taking place during ultraviolet irradiation in air. The experiment in nitrogen indicates that the oxidation of Eu²⁺ is directly related to the oxygen in air and should be mainly responsible for the degradation of Eu²⁺. It reveals that the Mn²⁺ centers always remain stable during irradiation but its emission is involved in the energy transfer of Eu²⁺→Mn²⁺. Thus, the oxidation of Eu²⁺ also leads to the degradation of Mn²⁺.