Eu$lt;sup$gt;2+$lt;/sup$gt;的掺杂浓度对BaAl$lt;sub$gt;2$lt;/sub$gt;Si$lt;sub$gt;2$lt;/sub$gt;O$lt;sub$gt;8$lt;/sub$gt;：Eu$lt;sup$gt;2+$lt;/sup$gt;荧光粉发光特性的影响

采用化学共沉淀法一次煅烧工艺合成了BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉.用X射线衍射仪和荧光分光光度计等对BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的相结构、发光性能进行了测试.结果表明：化学共沉淀法一次煅烧工艺合成的BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉为单相;其激发光谱分布在240—410 nm的波长范围,峰值位于320 nm处,可以被InGaN管芯产生的350—410 nm辐射有效激发;在365 nm近紫外光的激发下,测得其发射光谱是位于465 nm附近的宽带峰.BaAl₂Si₂O₈：Eu²⁺蓝色荧光粉的发光强度随Eu²⁺浓度的增大逐渐加强,当Eu²⁺掺杂的摩尔分数为3.5%时,发光强度达到最大值,而后随掺杂浓度的增加而减小,发生浓度猝灭;根据Dexter能量共振理论,该浓度猝灭是由于Eu²⁺的离子间交换相互作用引起的. 关键词： 2Si₂O₈：Eu²⁺')" href="#">BaAl₂Si₂O₈：Eu²⁺ 发光特性 蓝色荧光粉 化学共沉淀法     

Ca$lt;sub$gt;2$lt;/sub$gt;Si（O$lt;sub$gt;4-$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;N$lt;sub$gt;$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;）：Eu$lt;sup$gt;2+$lt;/sup$gt;绿色荧光粉的制备及其发光性能

利用在Ca-Si-O干凝胶前驱体中添加Si₃N₄的方法于非还原气氛下合成了含N固溶体Ca₂Si（O_4-xN_x）：Eu²⁺绿色荧光粉. 通过X射线衍射仪、扫描电子显微镜以及荧光分光光度计分别分析了产物的物相结构、颗粒形貌和发光性能. 结果显示,Si₃N₄与前驱体的混合物在非还原气氛（纯氮气）下于1100℃焙烧后获得含N固溶体Ca₂Si（O_4-xN_x）：Eu²⁺荧光粉,特别是其中Eu³⁺被还原为Eu²⁺,产物的晶体结构与βup -Ca₂SiO₄相一致. Ca₂Si（O_4-xN_x）：Eu²⁺能够被270–400 nm 范围内的紫外线有效激发,其发射光谱呈宽带发射. 随着N含量的增加,发射峰出现一定程度红移（501–504 nm）,而且发光强度显著提高. 当Eu²⁺浓度为0.25 mol%时发光强度达最大值,浓度超过0.25 mol%时,发光强度显著降低,出现浓度猝灭 效应. 关键词： 白光LED 荧光粉 溶胶凝胶法 3N₄')" href="#">Si₃N₄     

PDP用发光材料的研究进展

目前,商用PDP三基色荧光粉主要为红色(Y,Gd)BO₃:Eu³⁺,绿色Zn₂SiO₄:Mn²⁺、BaAl₁₂O₁₉:Mn²⁺或(Gd, Y)BO₃:Tb³⁺,蓝色BaMgAl₁₀O₁₇:Eu²⁺。然而,以上3种荧光粉均存在发光效率低的问题;另外,(Y, Gd)BO₃:Eu³⁺的色纯度较差,Zn₂SiO₄:Mn²⁺和BaAl₁₂O₁₉:Mn²⁺的衰减时间较长,(Gd,Y)BO₃:Tb³⁺亮度不足,BaMgAl₁₀O₁₇:Eu²⁺的稳定性较差,这些因素在一定程度上制约了其发光和显示性能。本文总结了目前红、绿、蓝三种发光材料的真空紫外发光机理以及发光性能改进的研究进展,同时,对目前开发新型PDP用发光材料的研究也进行了介绍。     

SrB4O7：Pr3+,Mn2+中的Pr→Mn能量传递

从能量传递的角度出发,利用同步辐射光源(德国HASYLAB实验室的SUPERLUMI实验站)对Pr³⁺和Mn²⁺掺杂的SrB₄O₇粉末样品进行了光谱研究.206nm激发下,在SrB₄O₇:Pr³⁺(0.1%,摩尔分数)样品中观察到了来自Pr³⁺离子1S0能级的光子级联发射.SrB₄O₇:Pr³⁺样品的发射谱与SrB₄O₇:Mn²⁺样品监测Mn²⁺离子640nm发射的激发谱在330~430nm的波长范围里存在显著的光谱重叠.这个光谱重叠有利于Pr³⁺→Mn²⁺的能量传递发生,从而将Pr³⁺离子级联发射中第一步不实用的紫外或近紫外光子转换为Mn²⁺的红光发射.双掺杂样品SrB₄O₇:Pr³⁺,Mn²⁺与单掺杂样品SrB₄O₇:Pr³⁺的发射谱比较揭示出Pr³⁺→Mn²⁺的能量传递的确存在,并且提供了一种传递效率的估算方法,表明通过“Pr³⁺-Mn²⁺”组合有可能获得量子效率大于1的高效真空紫外激发发光材料.     

钙钛矿型锰氧化物(La$lt;sub$gt;0.8$lt;/sub$gt;Eu$lt;sub$gt;0.2$lt;/sub$gt;)$lt;sub$gt;4/3$lt;/sub$gt;Sr$lt;sub$gt;5/3$lt;/sub$gt;Mn$lt;sub$gt;2$lt;/sub$gt;O$lt;sub$gt;7$lt;/sub$gt;的磁性和电性研究

采用传统固相反应法制备钙钛矿型锰氧化物 (La_0.8Eu_0.2)_4/3Sr_5/3Mn₂O₇多晶样品, X-射线衍射分析表明, 样品(La_0.8Eu_0.2)_4/3Sr_5/3Mn₂O₇结构呈现良好的单相. 通过磁化强度随温度的变化曲线(M-T)、不同温度下磁化强度随磁场的变化曲线(M-H)和电子自旋共振谱发现: 在300 K以下, 随着温度的降低, 样品先后经历了二维短程铁磁有序转变 (T_C^2D ≈ 282 K)、三维长程铁磁有序转变(T_C^3D ≈ 259 K)、奈尔转变(T_N ≈ 208K)和电荷有序转变(T_CO ≈ 35 K); 样品 (La_0.8Eu_0.2)_4/3Sr_5/3Mn₂O₇在T_N以下, 主要处于反铁磁态; 在T_C^3D达到370 K时, 样品处于铁磁-顺磁共存态, 在370 K以上时样品进入顺磁态. 此外, 分析电阻率随温度的变化曲线(ρ-T)得到: 样品在金属-绝缘转变温度(T_P ≈ 80 K)附近出现最大磁电阻值, 其位置远离T_C^3D, 表现出非本征磁电阻现象, 其磁电阻值约为61%. 在T_CO以下, 电阻率出现明显增长, 这是由于温度下降使原本在高温部分巡游的e_g电子开始自发局域化增强所致. 通过对 (La_0.8Eu_0.2)_4/3Sr_5/3Mn₂O₇的ρ-T 曲线拟合, 发现样品在高温部分的导电方式基本遵循小极化子的导电方式. 关键词： 磁性 电性 金属-绝缘转变温度 电子自旋共振     

Ce$lt;sup$gt;3+$lt;/sup$gt;在LiBaBO$lt;sub$gt;3$lt;/sub$gt;中的发光特性及晶体学格位

采用固相法制备了LiBaBO₃：Ce³⁺发光材料.测得LiBaBO₃：Ce³⁺材料的发射光谱为一不对称的单峰宽谱,主峰位于440 nm;监测440 nm发射峰,可得其激发光谱为一主峰位于370 nm的宽谱.利用van Uitert公式计算了Ce³⁺取代LiBaBO₃中Ba²⁺时所占晶体学格位,得出438 nm发射带归属于九配位的Ce³⁺发射,而469 nm发射带起源于八配位的Ce³⁺发射.研究了Ce³⁺浓度对LiBaBO₃：Ce³⁺材料发光强度的影响,结果显示,随Ce³⁺浓度的增大,发光强度呈现先增大后减小的趋势,Ce³⁺浓度为3mol%时强度最大,造成其浓度猝灭的原因为电偶极-偶极相互作用.引入Li⁺,Na⁺或K⁺可增强LiBaBO₃：Ce³⁺材料的发射强度.利用InGaN管芯（370 nm）激发LiBaBO₃：Ce³⁺材料,获得了很好的蓝白光发射,色坐标为（x=0.291,y=0.297）. 关键词： 白光发光二极管 3：Ce³⁺')" href="#">LiBaBO₃：Ce³⁺ 晶体学格位 发光特性     

Sr位Nd掺杂对SrBi$lt;sub$gt;2$lt;/sub$gt;Nb$lt;sub$gt;2$lt;/sub$gt;O$lt;sub$gt;9$lt;/sub$gt;性能的影响及机理研究

采用传统固相法制备了（Sr_1-3x/2A_x/2Nd_x）Bi₂Nb₂O₉（x=0,0.05,0.1和0.2）陶瓷,并系统研究了Nd离子取代Sr离子对SrBi₂Nb₂O₉性能的影响及其作用机理.研究结果表明：Sr_1-3x/2A_x/2Nd_xBi₂Nb₂O₉的介电常数和介电损耗随温度变化的行为具有明显的离子松弛极化特征.Nd³⁺对Sr²⁺的部分取代,导致Sr_1-3x/2A_x/2Nd_xBi₂Nb₂O₉剩余极化强度P_r稍有下降,但其压电系数d₃₃却有所增加,根据铁电热力学理论,这是Nd³⁺对Sr²⁺取代导致材料介电常数增大所致.Sr_1-3x/2A_x/2Nd_xBi₂Nb₂O₉的居里温度（T_C）没有随Nd含量的增加而变化,拉曼光谱技术分析表明这是其NbO₆八面体畸变程度没有发生变化所致.Nd³⁺取代Sr²⁺提高了材料的介电常数ε_r、压电系数d₃₃、机电耦合系数K_p,同时降低了机械品质因数Q_m,但是谐振频率温度系数C值没有改变. 关键词： 压电陶瓷 介电性能 压电性能 拉曼光谱     

CO$lt;sub$gt;2$lt;/sub$gt;激光烧结合成负热膨胀材料Sc$lt;sub$gt;2$lt;/sub$gt;($lt;i$gt;M$lt;/i$gt;O$lt;sub$gt;4$lt;/sub$gt;)$lt;sub$gt;3$lt;/sub$gt;($lt;i$gt;M$lt;/i$gt;=W,Mo)及其拉曼光谱

用CO₂激光烧结合成了负热膨胀材料Sc₂(WO₄)₃和Sc₂(MoO₄)₃. 实验表明, 激光合成负热膨胀材料Sc₂(WO₄)₃和Sc₂(MoO₄)₃属于快速合成技术, 合成一个样品的时间仅需几秒到十几秒, 具有快速凝固的特征; X射线衍射和拉曼光谱分析表明, 所合成的材料为正交相结构, 且具有较高的纯度; 变温拉曼光谱分析表明, 所合成的材料在室温以上没有相变, 但可能有微弱的吸水性; 在对Sc₂O₃, MoO₃, WO₃, Sc₂(MoO₄)₃和Sc₂(WO₄)₃拉曼光谱分析的基础上, 给出了激光光子能量及原料和合成产物的声子能级图, 分析了激光烧结合成的机理. 激光光子能量转化为激发声子的能量是光热转化的主要通道, 原料在熔池中反应并快速凝固形成最终产物. 关键词： 负热膨胀材料 合成 激光烧结 拉曼光谱     

Ti掺杂W$lt;sub$gt;18$lt;/sub$gt;O$lt;sub$gt;49$lt;/sub$gt;纳米线的电子结构与NO$lt;sub$gt;2$lt;/sub$gt;敏感性能的第一性原理研究

采用基于密度泛函理论框架下的第一性原理平面波超软赝势方法,通过理论建模,研究了Ti掺杂的非化学计量比W₁₈O₄₉纳米线的几何与能带结构以及电子态密度,并通过进一步计算NO₂/Ti-W₁₈O₄₉纳米线吸附体系的吸附能、电荷差分密度与电荷布居,分析了Ti掺杂W₁₈O₄₉纳米线的气体吸附与敏感性能. 计算发现,Ti掺杂改变了W₁₈O₄₉纳米线的表面电子结构,引入的额外的杂质态密度和费米能级附近能带结构的显著变化,使掺杂纳米线带隙与费米能级位置改变,纳米线导电性能增强. 吸附在W₁₈O₄₉纳米线表面的NO₂作为电子受体从纳米线导带夺取电子,导致纳米线电导降低,产生气体敏感响应. 与纯相W₁₈O₄₉纳米线相比,NO₂/Ti-W₁₈O₄₉纳米线吸附体系内部存在更多的电子转移,从理论上定量地反映了Ti掺杂对改善W₁₈O₄₉纳米线气敏灵敏度的有效性. 对Ti掺杂纳米线不同气体吸附体系电子布居的进一步计算表明,Ti掺杂纳米线对NO₂气体具有良好的灵敏度和选择性. 关键词： 密度泛函计算 Ti掺杂 18O₄₉纳米线')" href="#">W₁₈O₄₉纳米线 气敏     

H$lt;sub$gt;2$lt;/sub$gt;$lt;sup$gt;+$lt;/sup$gt;在强激光场中的解离及其量子调控的理论研究

利用非波恩-奥本海默近似的三维含时量子波包法,理论研究了氢分子离子在强激光场中的解离动力学.通过分析H₂⁺在不同的初始振动态（ν=0–9）和激光场强度下的解离核动能谱,得到了H₂⁺的光解离机理及其随激光场的变化规律.研究结果表明：当激光场的强度I₁=5.0×10¹³ W/cm²时,分子的解离来源于高振动态ν=5–9,其解离机理主要是通过键软化、键硬化和阈下解离过程.当激光场的强度I₂=1.0×10¹⁴ W/cm² 时,H₂⁺在低振动态ν=3–4上的阈上解离起主导作用,而高振动态的键软化、键硬化和阈下解离所占的比重明显地下降了.研究结果为后续的量子调控的实验研究提供了科学的理论预测和指导. 关键词： 光解离 氢分子离子 含时波包法 核动能谱     

Characterization of host-lattice emission and energy transfer in BaMgAl10O17:Eu

Host-lattice emission, energy transfer and degradation processes are characterized in undoped and Eu-doped BaMgAl₁₀O₁₇. Undoped BaMgAl₁₀O₁₇ exhibits a broad emission centered at 265 nm when excited at wavelengths shorter than 190 nm. This emission is assigned to exciton recombination at Ba-O groups in the cation layer of the lattice. The emission exhibits excellent overlap with the excitation band of Eu²⁺ in this host, providing a means of host-to-activator energy transfer in the doped phosphor. The exciton emission is relatively stable to thermal damage, but undergoes a peak shift and significant decrease in intensity after exposure to VUV radiation. Heating of VUV-damaged materials in air leads to some repair of the spectral properties.     

节能灯用BaMgAl10O17:Eu2+,Mn2+荧光粉的劣化机理研究

对节能灯用BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺荧光粉的热劣化和紫外辐照劣化机理进行了对比研究. 发现热处理和紫外辐照处理均对BaMgAl₁₀O₁₇: Eu²⁺,Mn²⁺产生明显的发光劣化作用. 研究结果表明：热劣化主要涉及到Eu²⁺ 的氧化及其格位偏移, 而紫外辐照劣化与上述过程无关. 紫外辐照劣化主要源自高能紫外辐照使Eu²⁺ 处于更加不稳定的状态, 从而降低Eu²⁺ 的直接吸收和发射强度.     

Novel green-emitting Na2CaPO4F:Eu phosphors for near-ultraviolet white light-emitting diodes

In this study, green-emitting Na₂CaPO₄F:Eu²⁺ phosphors were synthesized by solid-state reactions. The excitation spectra of the phosphors showed a broad hump between 250 and 450 nm; the spectra match well with the near-ultraviolet (NUV) emission spectra of light-emitting diodes (LEDs). The emission spectrum showed an intense broad emission band centered at 506 nm. White LEDs were fabricated by integrating a 390 nm NUV chip comprising blue-emitting BaMgAl₁₀O₁₇:Eu²⁺, green-emitting Na₂CaPO₄F:0.02 Eu²⁺, and red-emitting CaAlSiN₃:Eu²⁺ phosphors into a single package; the white LEDs exhibited white light with a correlated color temperature of 5540 K, a color-rendering index of 90.75, and color coordinates (0.332, 0.365) close to those of ideal white light.     

SiN掺杂提高BaMgAl10O17:Eu2+荧光粉光学性能的第一性原理研究

使用基于密度泛函理论的CASTEP软件计算了BAM:Eu²⁺(BaMgAl₁₀O₁₇:Eu²⁺)荧光粉在SiN掺杂前后的能带、态密度、吸收光谱和Mulliken布居．Eu²⁺处于BR位置光吸收更强;SiN掺杂使处于BR位置的Eu²⁺的数量上升,而处于mO位置的Eu²⁺的数量下降,抵消了SiN掺杂降低Eu的态密度对光谱的影响．所以适量掺杂的SiN提高了BAM:Eu²⁺荧光粉的吸收发射光谱强度．Si-N键和Eu-N键的Mulliken布居数分别高于Al-O键和Eu-O键, 说明Si-N键和Eu-N键的共价性分别强于Al-O键和Eu-O键．发光中心Eu²⁺局域结构共价性的增强降低了BAM:Eu²⁺镜面层的活性,这是SiN掺杂提高BAM:Eu²⁺+荧光粉光学稳定性的主要原因．     

The structure and luminescence properties of long afterglow phosphor Y3−xMnxAl5−xSixO12

A series of phosphors with the composition Y_3−xMn_xAl_5−xSi_xO₁₂ (x=0, 0.025, 0.050, 0.075, 0.150, 0.225, 0.300) were prepared with solid state reactions. The X-ray powder diffraction analysis of samples shows that the substitution of Mn²⁺ and Si⁴⁺ does not change the garnet structure of phosphors, but makes the interplanar distance decrease to a certain extent. The emission spectra show that Mn²⁺ in Y₃Al₅O₁₂ emits yellow-orange light in a broad band. With the increment of substitution content, the emission intensity of the phosphors increases firstly then decreases subsequently, and the emission peak moves to longer wavelength. Afterglow spectra and decay curves show that all the Mn²⁺ and Si⁴⁺ co-doped samples emit yellow-orange light with long afterglow after the irradiation of ultraviolet light. The longest afterglow time is 18 min. Thermoluminescence measurement shows that there exist two kinds of traps with different depth of energy level and their depth decreases with the increment of substitution content.     

The structure and luminescence properties of a novel orange emitting phosphor Y3MnxAl5−2xSixO12

A series of phosphors with the composition Y₃Mn_xAl_5−2xSi_xO₁₂ (x=0, 0.05, 0.1, 0.15, 0.2, 0.3, 0.4, 0.5, 0.6) was prepared through solid state reactions. X-ray powder diffraction analysis of samples shows that when co-doping content does not exceed 16% of Al³⁺, equimolar co-doping of Mn²⁺ and Si⁴⁺ does not change the garnet structure of phosphors, but makes the interplanar distance to decrease a certain extent. However, if the co-doping content exceeds 16%, new phases will form in the samples. The excitation and emission spectra of samples show that Mn²⁺ in Y₃Mn_xAl_5−2xSi_xO₁₂ emits broadband orange light (peak wavelength varies from 586 to 593 nm). With an increment in co-doping content, the emission intensity of the phosphors increases when the value of x is lower than 0.1 while it decreases when it is higher than 0.1 and the emission peak moves to a longer wavelength.     

Photoluminescence properties of Sr(Y, Gd)2O4:Euunder VUV excitation

Vacuum ultraviolet (VUV) excitation and photoluminescence (PL) properties of Sr(Y, Gd)₂O₄ doped with Eu³⁺ were studied. The excitation spectra of SrY_1.9Eu_0.1O₄ and SrY_1.0Gd_0.9Eu_0.1O₄ had absorption in the VUV region with the absorption band edge at 149 nm, while the absorption of SrGd_1.9Eu_0.1O₄ in the VUV region was weak, which could be due to the narrow host band gap and no efficient energy transfer occurred in the VUV region. The PL spectra of all samples exhibited the characteristic emission of Eu³⁺ with the red ⁵D₀-⁷F₂ transition (611 nm) being the most prominent group.     

Optical spectroscopy of Ca3Sc2Si3O12, Ca3Y2Si3O12 and Ca3Lu2Si3O12 doped with Pr

The silicates Ca₃Sc₂Si₃O₁₂, Ca₃Y₂Si₃O₁₂ and Ca₃Lu₂Si₃O₁₂, both undoped and doped with Pr³⁺ ions, have been synthesized by solid-state reaction at high temperature. The luminescence spectroscopy and the excited state dynamics of the materials have been studied upon VUV and X-ray excitation using synchrotron radiation. All doped samples have shown efficient 5d-4f emission upon direct VUV excitation of 5d levels, but only Ca₃Sc₂Si₃O₁₂:Pr³⁺ shows luminescence upon interband VUV or X-ray excitation. The VUV excited emission spectra of Ca₃Y₂Si₃O₁₂:Pr³⁺ and Ca₃Lu₂Si₃O₁₂:Pr³⁺ show features attributed to emission from two distinct sites accommodating the Pr³⁺ dopant. The decay kinetics of the Pr³⁺ 5d-4f emission in Ca₃Sc₂Si₃O₁₂:Pr³⁺ upon VUV excitation across the band gap are characterized by decay times in the range 25-28 ns with no significant rise after the excitation pulse. They appear to be faster upon X-ray irradiation than for VUV excitation. Weak afterglow components are attributed to defect luminescence.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.     

Mn, Cr-co-doped MgAl2O4 phosphors for white LEDs

The Mn-, Cr-doped and Mn, Cr-co-doped MgAl₂O₄ powders have been synthesized via a gel-solid reaction method. Energy transfer from Mn²⁺ to Cr³⁺ has been observed for the first time in the co-doped MgAl₂O₄ phosphors. When excited with blue light with a wavelength of 450 nm at room temperature, both green emission from Mn²⁺ around 520 nm and red emission from Cr³⁺ around 675and 693 nm were generated. Moreover, the color of the emission can be modified by controlling the doping concentrations of Mn²⁺ and Cr³⁺. Therefore, MgAl₂O₄: Mn²⁺, Cr³⁺ could be used as a single-phased phosphor for white LED with a blue LED chip. The energy transfer in terms of Mn²⁺ to Cr³⁺ is determined by means of radiation and reabsorption.