电子成像均匀约束磁场的产生及测试分析

为增加离子与原子碰撞成像系统中探测电子的立体角，设计了一约束电子的复合型亥姆霍兹线圈装置.对复合型亥姆霍兹线圈的磁场分布进行了理论计算和分析，并对制作的复合型亥姆赫兹线圈产生的磁场进行了实验测量，得出磁场的均匀性好于±0.6%. 关键词： 亥姆霍兹线圈 磁场分布 磁场均匀性     

亥姆霍兹线圈轴线磁场计算机测量实验研究

亥姆霍兹线圈产生的磁场具有广泛的物理应用。利用霍尔传感器件,研究制作了具有USB2．0数据通讯接口的高速磁场数据测量装置,编写了磁场数据采集处理程序,设计了中心距可调的亥姆霍兹线圈并用所研制的仪器进行了轴向磁场分布测量。结果表明：该实验装置测量精度高,实时性好,实验手段先进,可扩展为多个设计性物理实验。     

基于电磁感应法测量亥姆霍兹线圈磁场的改进

本文在电磁感应法的基础上,通过与亥姆霍兹线圈串联使电容达到谐振的改进方法,测量了不同电容参数下的亥姆霍兹线圈磁场分布,并利用Origin软件拟合分析了亥姆霍兹线圈磁场与中心轴线位置的关系.实验结果表明,基于电磁感应的改进方法测得的亥姆霍兹线圈磁场精确度在一定程度上均大于传统电磁感应法的测量结果,3种电容选择中,串联电容为0.099×10^-6F时,精确度最高,拟合的亥姆霍兹线圈磁场与中心轴线位置的关系式与理论状态下的公式基本吻合.改进方法的实验效果明显,精确度高,科学可行,是一种值得推广的测量亥姆霍兹线圈磁场的改进方法.     

对亥姆霍兹线圈磁场分布的分析

利用DH4501D实验仪探究了亥姆霍兹线圈轴线上和轴线外的磁场分布问题。首先通过对单个线圈不同电流下的磁场分布的实验值与理论值对比发现电流大的磁场更接近理论值,更适合用来研究磁场分布问题。然后利用较大电流分别研究了单个线圈以及亥姆霍兹线圈轴线上和轴线外的磁场分布的规律及产生原因。最后利用磁场分布拟合了真空磁导率并与理论值进行了对比。通过对这些问题的研究不仅加深了对毕奥-萨伐尔定律的理解,更加明确了亥姆霍兹线圈的磁场分布规律。     

平行共轴线圈的磁场特征研究与实验设计

通过计算机及相关的传感器和数据采集接口辅助,研究了平行共轴双线圈间距分别为0.5R,R,1.5R时,轴线方向磁场强度的分布规律及特征.从平行共轴双线圈间距为R的亥姆霍兹线圈所形成的均匀磁场出发,结合理论推导,自己设计并组装了三线圈实验装置,实现了平行共轴三线圈均匀磁场区域扩大、强度增强的实验设计,在一定程度上弥补了传统亥姆霍兹线圈磁场测量的不足并有助于对其深入的理解和研究.     

利用霍尔效应测磁场实验的数据处理

推导了亥姆霍兹线圈产生磁场的全空间分布的普遍公式,讨论了如何确定磁感应强度的方向。就实验内容进行了实例分析,利用Matlab软件进行了相关计算,提出了利用霍尔效应测磁场实验的数据处理方法。最后,详细讨论了亥姆霍兹线圈所在平面处磁场强度相关参数的分布曲线。     

亥姆霍兹线圈的均匀磁场区

近年来,在普通物理实验中新开设了“磁场描绘”实验.它以1000赫芝的低频信号作励磁电源,用两个700匝、平均半径为10厘米的圆线圈产生磁场.探测线圈有1100匝、平均半径3.65毫米.实验要求测绘图线圈轴线平面上的磁感应线和亥姆霍兹线圈的均匀磁场区. 从学生的实验报告看,圆线圈轴线平面上磁感应线的描绘基本上是正确的.但亥姆霍兹线圈的均匀磁场区则形状各异,很不一致. 本文试图在简化实验条件的基础上,从理论上计算亥姆霍兹线圈均匀磁场区的范围,作为正确判断实验结果的依据. 一、圆电流轴线平面上任一点 磁感强度的数学表达式 根据毕奥-萨伐…     

亥姆霍兹线圈磁场的探究

定量计算了亥姆霍兹线圈空间磁场的分布,并用Mathmatic进行空间模拟,形象地描述了亥姆霍兹线圈的空间磁场分布,同时就其均匀性与三线圈和载荷旋转圆盘的磁场进行了对比讨论.     

亥姆霍兹线圈轴平面磁场分布的实验研究

根据毕奥—萨伐尔定律,导出了亥姆霍兹线圈轴平面磁场的分布解析表达式,以解析表达式为基础对亥姆霍兹线圈实例进行了数值计算,并与实验结果做一比对,最后,对一些特殊场点作了讨论。     

亥姆霍兹线圈磁场分布及其测量

采用美国PASCO公司生产的＂科学工作室＂物理实验系统重新设计了亥姆雷兹线圈磁场实验,以定量分析的实验形式,弥补了传统方法测量亥姆霍兹线圈磁场的不足,同时也体现了PASCO科学工作室在实验数据采集方面具有传统方法不可比拟的优点。     

脉冲磁体增强技术发展概述

在脉冲强磁体设计中，磁应力是目前面临的最大困难，当磁场强度达到100T时，磁体绕组中的磁应力高达4GPa，这是目前任何实用导体材料都无法随的，因此，脉冲强磁体的发展在很大程度上取决于磁应力的解决情况，文章介绍了国外在解决脉冲强磁体巨大问题上采用的方法，主要叙述了新材料技术，绕组加固技术和改善电流分布技术，并对其优缺点及性能进行了分析。     

改进型Helmholtz线圈及其磁场均匀性的分析

提出将Helmholtz线圈改为3个同半径的串联线圈,以得到改进型的Helmholtz线圈,经计算得到了改进型Helmholtz线圈磁场的简单公式,对公式的分析表明：改进型Helmholtz线圈的均匀磁场区比一般Helmholtz线圈大得多。     

Multi-objective optimization of gradient coil for benchtop magnetic resonance imaging system with high-resolution

Significant high magnetic gradient field strength is essential to obtaining high-resolution images in a benchtop mag- netic resonance imaging （BT-MRI） system with permanent magnet. Extending minimum wire spacing and maximum wire width of gradient coils is one of the key solutions to minimize the maximum current density so as to reduce the local heating and generate higher magnetic field gradient strength. However, maximum current density is hard to optimize together with field linearity, stored magnetic energy, and power dissipation by the traditional target field method. In this paper, a new multi-objective method is proposed to optimize the maximum current density, field linearity, stored magnetic energy, and power dissipation in MRI gradient coils. The simulation and experimental results show that the minimum wire spacings are improved by 159% and 62% for the transverse and longitudinal gradient coil respectively. The maximum wire width increases from 0.5 mm to 1.5 mm. Maximum gradient field strengths of 157 mT/m and 405 mT/m for transverse and lon- gitudinal coil are achieved, respectively. The experimental results in BT-MRI instrument demonstrate that the MRI images with in-plane resolution of 50 ~tm can be obtained by using the designed coils.     

强激光辐照下纳米晶体铜薄膜层裂破坏的实验研究

采用强激光辐照加载技术和激光速度干涉(VISAR)测试技术，对纳米晶体铜薄膜的层裂特性进行实验测量和分析.基于VISAR实测的自由面速度波形，计算得到纳米晶体铜薄膜在超高拉伸应变率下的层裂强度高达3 GPa，明显高于多晶铜的层裂强度, 其原因归咎于纳米晶体材料中存在大量晶界阻碍了位错运动.     

强激光辐照下纳米晶体铜薄膜层裂破坏的实验研究

采用强激光辐照加载技术和激光速度干涉(VISAR)测试技术,对纳米晶体铜薄膜的层裂特性进行实验测量和分析.基于VISAR实测的自由面速度波形,计算得到纳米晶体铜薄膜在超高拉伸应变率下的层裂强度高达3 GPa,明显高于多晶铜的层裂强度, 其原因归咎于纳米晶体材料中存在大量晶界阻碍了位错运动. 关键词： 纳米晶体铜薄膜 层裂 激光辐照     

An efficient calibration method for SQUID measurement system using three orthogonal Helmholtz coils

For a practical superconducting quantum interference device(SQUID) based measurement system,the Tesla/volt coefficient must be accurately calibrated.In this paper,we propose a highly efficient method of calibrating a SQUID magnetometer system using three orthogonal Helmholtz coils.The Tesla/volt coefficient is regarded as the magnitude of a vector pointing to the normal direction of the pickup coil.By applying magnetic fields through a three-dimensional Helmholtz coil,the Tesla/volt coefficient can be directly calculated from magnetometer responses to the three orthogonally applied magnetic fields.Calibration with alternating current(AC) field is normally used for better signal-to-noise ratio in noisy urban environments and the results are compared with the direct current(DC) calibration to avoid possible effects due to eddy current.In our experiment,a calibration relative error of about 6.89 × 10-4is obtained,and the error is mainly caused by the non-orthogonality of three axes of the Helmholtz coils.The method does not need precise alignment of the magnetometer inside the Helmholtz coil.It can be used for the multichannel magnetometer system calibration effectively and accurately.     

Domain wall dynamics and Hall effect in eddy current loop in amorphous ferromagnetic wire with small helical anisotropy

Small helical anisotropy was induced in amorphous ferromagnetic Co_68.2Fe_4.3Si_12.5B₁₅ wire by current annealing and simultaneous application of tensile stress and torsion. Presence of helical anisotropy was confirmed by measurement and analysis of the circular magnetic flux versus axial magnetic field hysteresis loops. These measurements also showed that a single domain wall between circular domains can be created by placing the wire in a sufficiently high inhomogeneous magnetic field generated by Helmholtz coils with opposite currents. The domain wall velocity versus axial driving field was measured. The results show that the basic dynamic properties (magnitude of the wall mobility, field interval in which linear dependencies between velocity and field are observed, accelerated increase of the velocity for higher fields) are very similar to those obtained for the domain wall between circular domains driven by a constant circular field. The Hall effect was detected in the eddy current loop generated by the moving domain wall.     

Frequency difference lock-in phenomenon's weakening by transverse magnetic field in Y-shaped cavity dual-frequency laser

We report experimental progress in weakening the frequency difference lock-in phenomenon in a Y-shaped cavity dual-frequency laser. A cube coil pair is chosen to provide a uniform magnetic field for tunability and uniformity of magnetic field strength. When the transverse magnetic field intensity is 9 m T, the frequency difference lock-in phenomenon is evidently weakened and the frequency difference can be continuously tuned in the range of0.12 MHz to 1.15 GHz. Moreover, the relationship between the minimal frequency difference and magnetic field intensity are investigated and discussed. Then a Y-shaped cavity dual-frequency laser is expected to be utilized as an optimum light source for heterodyne interferometric sensing and precise laser measurement.     

Effect of a fullerene C60 addition on the strength properties of nanocrystalline copper and aluminum under shock-wave loading

The Hugoniot elastic limit and the spall strength of aluminum and copper samples pressed from a mixture of a metallic powder and 2–5 wt % C₆₀ fullerene powder are measured under a shock loading pressure up to 6 GPa and a strain rate of 10⁵ s^?1 by recording and analyzing full wave profiles using a VISAR laser interferometer. It is shown that a 5% C₆₀ fullerene addition to an initial aluminum sample leads to an increase in its Hugoniot elastic limit by an order of magnitude. Mixture copper samples with 2% fullerene also exhibit a multiple increase in the elastic limit as compared to commercial-grade copper. The elastic limits calculated from the wave profiles are 0.82–1.56 GPa for aluminum samples and 1.35–3.46 GPa for copper samples depending on the sample porosity. The spall strength of both aluminum and copper samples with fullerene additions decreases approximately threefold because of the effect of high-hardness fullerene particles, which serve as tensile stress concentrators in a material under dynamic fracture.