热稳定空穴传输材料的合成及其电致发光器件

合成了两种NPB的新衍生物:N,N’-二(1-萘基)-N,N’-二(4-甲基苯基)-1,1’-联苯-4,4’二胺(NTB)和N,N’-二(1-萘基)-N,N’-二(4-叔丁基苯基)-1,1’-联苯-4,4’二胺(NBB)。DSC测得其玻璃态转变温度分别为108℃和129℃,表现出好的热稳定性。紫外光电子能谱测得其电离势均为5.2eV。NTB和NBB固体光致发光光谱的最大发射波长分别位于455nm和460nm。分别以NPB、NTB、NBB作为空穴传输层材料(HTM)制作了结构相同的有机电致发光器件,3种器件发光光谱相同,均为Alq₃的绿色发光,器件的起亮电压分别为11,9,8V,在15V工作电压时的亮度分别为1000,1300,1200cd/m²,初步研究了器件的发光特性和稳定性。     

氟化钇电子注入层对OLED器件性能的影响

利用氟化钇(YF3)代替Li F作为电子注入层材料,以金属铝作为阴极,制备了有机电致发光器件(OLED)。实验结果表明:适当厚度的YF3电子注入缓冲层可以增强阴极的电子注入能力,使得电子和空穴的浓度更加平衡,有效地提高器件的电致发光性能。其中,1.2 nm厚YF3的器件具有最小的起亮电压2.6 V,最高的电流效率8.52 cd·A-1,最大的亮度36 530 cd·m-2。最大亮度和电流效率与Li F参考样品相比,分别提高了39%和53%。     

利用8-羟基喹啉锂作电子注入层以提高有机发光器件的发光效率

8-羟基喹啉锂用作有机电致发光器件的电子注入层能够提高阴极功函数,进而提高器件的发光效率。10的Liq薄膜足以降低有机电致发光器件中的开启电压并能有效提高器件效率,该现象可与LiF/Al作阴极的器件性能相比拟。利用不同阴极材料制作器件,讨论了8-羟基喹啉锂的电子注入机制,发现把Liq薄膜引入到Alq3和不同阴极之间后,器件的电流密度与所用阴极材料的种类无关。为了讨论电子在分界面上注入势垒的变化情况,对器件进行饱和光伏测试。测试发现Alq3/Liq/Al的分界面上真空能级的移动降低了电子注入势垒。推测此现象是由于在界面上形成了强偶极子,这也可能是有机电致发光器件中电子注入效率提高的机理之一。     

利用变温瞬态电致发光研究OLED载流子的输运机理

研究了不同温度下几种结构的有机电致发光器件(OLED)的瞬态电致发光响应特性以及电流密度-电压-亮度特性。研究发现,启亮电压随温度升高而减小的加速度在200 K时出现拐点,且这一数值主要由电子传输层Alq3的迁移率决定。当温度为200 K时,延迟时间td最重要的影响因素是Mo O3空穴注入势垒,随着温度的升高,Δtd逐渐减小,到300 K时基本消失。Vf代表光衰减时间随温度增长的平均速率。Mo O3注入层和电致发光材料Ir(ppy)3都会对载流子的堆积起促进作用。由Mo O3注入层不同引起的ΔVf是0.52μs/K,由电致发光材料Ir(ppy)3不同引起的ΔVf是0.73μs/K。     

新型苯乙烯衍生物掺杂的蓝色及白色有机电致发光器件

研究了新型高效蓝色掺杂剂EBDP的电致发光性能. 分别以EBDP为掺杂剂制备了结构为氧化铟 锡(ITO)/酞菁铜(CuPc)/N,N′-二(1-萘基)-N,N′-二苯基-1,1′-联苯-4-4′-二胺(NPB)/2- 叔丁基-9,10-二-(2-萘基)蒽(TBADN):EBDP/8-羟基喹啉铝(Alq₃)/LiF/Al 与ITO /CuPc/NPB/TBADN:EBDP: 4-二氰亚甲基-2-叔丁基-6-(1,1,7,7-四甲基久咯呢定基-9-烯基)- 4H-吡喃/Alq_{3 关键词： 有机电致发光 蓝色掺杂剂 蓝色电致发光器件 白色电致发光器件}     

采用瞬态EL和延迟EL测试方法研究磷光掺杂体系的内部发光过程

有机磷光发光二极管(OLED)因为理论内量子效率能达到100%而成为研究热点,但是至今有机磷光OLED器件发光机理及过程仍然不完全清楚,需进一步研究. 本文中搭建了一套瞬态电致发光和延迟电致发光的测量系统,并首次综合运用瞬态电致发光和延迟电致发光测量来探测有机磷光OLED 器件发光层内部电荷载流子的运动,从而分析研究其内部发光过程及机理. 研究中首先制备了一种高效红色磷光材料(pbt)₂Ir(acac)衍生物(Irf)掺杂荧光材料作为发光层的器件,对其进行了瞬态EL测量,发现当驱动脉冲信号撤销时瞬态发光强度会突然出现一个瞬时过冲现象(transient overshoot),通过实验分析证实这个发光的瞬时过冲是由于发光层内部电子和空穴累积造成的,还证实了在发光层与空穴传输层界面存在空穴的累积. 通过延迟电致发光的研究发现在这种掺杂体系中发光主要来自于客体材料Irf的直接俘获电子空穴复合发光,而不是来自于主客体之间的能量传递,器件中的空穴传输发生在客体材料Irf上,而电子传递则主要在主体材料TAZ上. 同时还发现空穴注入是整个掺杂体系中重要的影响因素. 关键词： 瞬态EL 延迟电致发光 三线态-三线态湮没 overshoot     

方波驱动法测定Alq3的电子迁移率

在非正弦波(方波)的驱动下,观察到了OLED中Alq₃的电致发光现象。在高段方波驱动下,Alq₃中的电子向阳极移动;在低段方波驱动下,Alq₃中的电子向阴极移动。当方波的周期是电子穿过Alq₃中所用时间的2倍时,Alq₃中的电致发光现象完全消失。由此,可以计算出Alq₃中的电子迁移率,得到的结果和文献的报道值相吻合。对Alq₃中电子迁移率和厚度的关系进行了研究,从而提出了一种简单易行的计算有机材料的电子迁移率的方法。     

利用级联式能量传递的有机电致发光器件

为了提高掺杂型有机电致发光器件(OLED)中主体发光材料与客体荧光染料间能量传递的效率,2-对联苯-8-羟基喹啉锌(Zn ₂)作为NPB : DCJTB掺杂体系的能量助传递剂,制备了结构如:ITO/NPB/NPB : DCJTB/Zn ₂/BCP/Al的有机电致发光器件。助传递剂Zn ₂的加入,能够两次利用Frster能量转移,实现NPB向DCJTB级联式的能量传递过程,提高低浓度时掺杂染料DCJTB红光发射的纯度;此外,还探讨了三者间能量传递的有效距离,即当助传递剂与掺杂体系的距离在小于10 nm的范围内,其参与能量传递的效率随着距离的增加而逐渐下降。     

利用氧等离子体处理阳极银实现高效率顶发射有机电致发光

主要报道在器件结构为玻璃衬底/Ag(阳极)/NPB(空穴传输层)/Alq3(电子传输及发光层)/Sm(半透明阴极)/Alq3的顶发射有机电致发光器件中,利用氧等离子体对阳极银的表面进行处理来降低阳极和空穴传输层(Ag/NPB)界面处的空穴注入势垒,提高顶发射有机电致发光器件的性能。主要研究了氧等离子体处理时间对阳极银和顶发射有机电致发光器件光电特性的影响。紫外光电子能谱表明,氧等离子体处理能有效降低Ag/NPB界面处的空穴注入势垒。通过优化处理时间获得最佳器件性能,优化后的器件最大效率可达6.14cd/A。     

基于器件结构提高TADF-OLED器件的发光性能

为了提高以TADF材料作为主体、天蓝色荧光材料作为客体的混合薄膜的OLED器件光电性能,我们调整了器件结构,使主体材料发挥其优势。制备了基本结构为ITO/NPB(40 nm)/DMAC-DPS∶x%BUBD-1(40 nm)/Bphen(30 nm)/LiF(0.5 nm)/Al的OLED器件。研究了主-客体材料在不同掺杂浓度下的OLED器件的光电特性。为了提高主体材料的利用率,在空穴传输层和发光层之间加入10 nm的DMAC-DPS作为间隔层;然后,在阳极和空穴传输层之间加入HAT-CN作为空穴注入层,形成HAT-CN/NPB结构的PN结,有效降低了器件的启亮电压(2.7 V)。测量了有无HAT-CN的单空穴器件的阻抗谱。结果表明,在最佳掺杂比例(2%)下,器件的外量子效率(EQE)达到4.92%,接近荧光OLED的EQE理论极限值;加入10 nm的DMAC-DPS作为间隔层,使得器件的EQE达到5.37%;HAT-CN/NPB结构的PN结有效地降低了器件的启亮电压(2.7 V),将OLED器件的EQE提高到5.76%;HAT-CN的加入提高了器件的空穴迁移率,降低了单空穴器件的阻抗。TADF材料作为主体材料在提高OLED器件的光电性能方面具有很大的潜力。     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.