单口径相干合成系统激光光束的M2因子研究

单口径相干合成系统激光光束的光束质量是一个亟待解决的重要问题.基于二阶矩定义, 文中给出了单口径TEM₀₀, TEM₀₁及TEM₁₀两两相干光束M²因子的解析表达式, 并比较分析了束腰宽度、传输距离、振幅之比,以及源场位置矢量对相干光束M²因子的影响, 得到了诸如源场位置参量d₁<100λ时,各相干光束M²因子恒定,反之, 其随位置参量d₁的增大而增大等一些结论.最后,文章对两TEM₀₀模相干光束M²因子的 部分理论进行了实验验证.     

InGaAsP SBH激光器光束质量的非傍轴分析

计算了InGaAsPSBH激光器的TE₀₀模,并利用非傍轴矢量矩理论,分析了平行于p-n结方向上的光学质量因子M_y²在以往有关M²的计算中,往往忽略了包层中光场的贡献,因此得出M²小于1的结论当半导体激光器的激活层的尺寸远小于发射波长时,大部分光场将渗透到包层中,因此,包层的光场是不能忽略的考虑到激活层和包层中的光场对M²的影响,给出了非傍轴半导体激光M²的精确表达式结果表明,M_y大于1.     

KGW 晶体外腔式高功率579 nm喇曼黄光激光器

报道了579 nm高功率KGd(WO₄)₂喇曼晶体外腔式喇曼黄光激光器的输出特性.基于808 nm脉冲激光二极管侧面泵浦Nd:YAG陶瓷、腔内BBO电光晶体同步延迟调Q和Ⅰ类临界相位匹配的LBO晶体腔外倍频方案,并通过外腔式KGW晶体Ng轴二阶斯托克斯喇曼频移,获得了579.54 nm黄光激光输出.当脉冲信号重复频率为1 kHz、532 nm泵浦光最高平均功率为5.02 W、脉冲宽度为10.1 ns时,获得了最高平均功率2.58 W、脉冲宽度7.4 ns、峰值功率348.6 kW的579.54 nm二阶斯托克斯喇曼黄光激光输出;532 nm至579.54 nm的光-光转化效率为51.4%、斜率效率为54.8%,光束质量因子M_x-579.54²=5.829、M_y-579.54²=6.336,输出功率不稳定性小于±2.35%.实验表明:外腔式喇曼结构能够高效地获得喇曼黄光,具有很高的光-光转化效率及良好的功率稳定性,并通过脉冲LD结合同步延迟电光调Q可获得高重复频率、高平均功率、窄脉冲宽度和高峰值功率的黄光激光输出.     

高功率光子晶体光纤激光器实验研究

 从光纤热传导方程出发,研究了不同泵浦光吸收系数对光纤激光器沿光纤长度方向温度分布的影响。结果表明,低吸收系数光纤泵浦端温度相对较低,分布较为平缓,有效减缓光纤的热损伤。根据理论分析结果,实验中选择了吸收系数为1.45 dB/m的掺Yb³⁺双包层光子晶体光纤作为增益介质,在泵浦光功率为560 W时,获得了428.5 W的高功率单模连续输出,斜率效率为76.5%,光束质量因子M²<1.2。由于泵浦端光纤温度较高,实验中对光纤两端进行了主动冷却,并且在离光纤端面约25 cm处的光纤表面温度进行实时测量,结果发现随着泵浦光功率的增加,光纤表面温度均匀增长,最高温度为310 K,温度正常。     

激光光束传输因子M2的一些问题

本文讨论与M²因子有关的一些问题,指出在近轴近似条件下由光束的二阶强度矩定义的M²因子满足M²≥1,其中只有对基模高斯光束等式才成立.由光束的功率通量值定义的M²因子(M_pc²)有可能小于1,M_pc²的大小取决于所定义的光斑半径内包含的光功率的百分数.通过计算光场的二阶矩,我们获得了轴向相干叠加的高斯光束的M²因子的解析解.     

半导体激光器的M2因子可以小于1

根据Porras的非傍轴矢量矩理论,对双异质结半导体激光器的光束质量进行了研究.结果表明,在有源层厚度d_a远小于波长λ的条件下,半导体激光器的M²因子可以小于1,并且没有下限.     

掺杂比对CdGe(As11-xPx)2倍频与参量振荡的影响

 在相位匹配和可接受掺杂比理论的基础上，针对CdGe((As1_1-xP_x)₂晶体，研究了掺杂比对频率转换的影响。依据Sellmeier方程得到了倍频和Ho³⁺:YLF与Cr:Er:YSGG激光器泵浦光学参量振荡的相位匹配调谐曲线，并给出了不同掺杂下的可接受掺杂比。结果表明：掺杂晶体可实现2~9 μm范围内非临界相位匹配的倍频和2~18 μm的参量光产生；随着掺杂比的增大，可接受掺杂比近似线性减小，并随着波长改变展现出了不同变化趋势。     

光在随机增益介质中的放大

 结合环形腔理论，运用蒙特卡罗法模拟了光子在介质中的随机行走。研究了倍频Nd:YAG（脉宽6 ns，频率20 Hz）脉冲激光器作为泵浦光，在TiO₂ / 若丹明 B有机增益介质中，散射微粒的颗粒密度和泵浦光面积对随机激光器阈值强度的影响。模拟结果表明：随机激光阈值和光子在增益介质中的随机行走路程长度和光子通过边界返回增益区和非增益区的几率有关。随着泵浦光面积的增加，随机激光器阈值降低；增益介质中散射颗粒密度的增加降低了随机激光器的阈值。     

双端泵浦固体激光器模匹配问题的实验研究

实验研究了高功率双端泵浦Nb:YVO₄固体激光器的谐振腔与泵浦光束的模匹配问题.实验发现了输出功率随激光在增益介质中模半径与泵浦光斑半径之比的变化规律.在低泵浦功率ω₀/ω_p<1的条件下,激光器输出功率随ω₀/ω_p的变化不敏感.但在高泵浦功率下,输出功率随ω₀/ω_p的减小而增加.ω₀/ω_p存在一个下限,无论泵浦功率的大小,当ω₀/ω_p低于此下限时基横模消失,高阶模出现.这对于高功率端面泵浦固体激光器腔型的设计具有一定的参考价值.     

激活介质热效应对振荡模式的影响研究

理论分析了激活介质热效应对端面泵浦固体激光器激光振荡模式分布的影响,并以光纤耦合半导体激光器端面泵浦Nd∶YAG激光器实验研究了激活介质热效应对激光振荡模式的影响。实验结果表明：由于热效应,基模的模体积随泵浦功率的增加而变大,基模在模式竞争中占优;在泵浦光轴线偏离几何腔轴时,基模光斑中心位置朝泵浦光轴线所在位置移动,偏离量与泵浦光轴线的偏离量近似成线性关系。利用实验结果指导腔调节,可使泵浦光轴线与几何腔轴精确重合,获得了椭圆率为0.98、M2因子为1.01的基模输出。     

Efficient design considerations for end-pumped solid-state-lasers

The temperature distribution in the gain medium and key design parameters for an ideal-four level end-pumped solid-state laser have been analyzed depending on the crystal's length, absorption coefficient, and pump beam M² factor. The optimum key design parameters and thermal focal lens are obtained by minimizing the root mean square of pump beam radius in the laser crystal. It is found that the focal thermal lens and key design parameters are dependent on the gain medium characteristics and pump beam properties as well. By considering the Poisson equation in cylindrical coordinate and Top-Hat pumping profile, an analytical formula has been derived to introduce the thermal focal length in the end-pumped lasers. A formula is also presented to relate the requirements of pump source to the gain medium properties for working laser at the design point.     

High efficiency,high repetition-rate Nd:YVO<Subscript>4</Subscript> laser with TEM<Subscript>00</Subscript> end-pumped by 887 nm

Thermal effect of laser crystal is a very important factor for solid lasers. The most of heat is generated from the quantum loss between pump light and lasing light. If a longer wavelength of pump light is adopted, quantum loss and quantum loss efficiency can be reduced and improved, respectively. In this paper, a Nd:YVO₄ laser end-pumped by 887 nm LD is reported. Output power of 25 W is obtained from a single Nd:YVO₄, when the crystal absorbs pump light power of 38 W. The corresponding opto-optic conversion efficiency is up to 65.7%. When 30.7 W pump light is absorbed in the crystal, 19.4 W TEM₀₀ is obtained with M _x ² = 1.30, M _y ² = 1.26 and opto-optic conversion efficiency of 63.2%. The laser can work at the Q-switched mode. The uniform pulses are generated at high repetition of 100 kHz. And the conditions of pulse stability are analyzed in this paper.     

Effect of absorbed pump power on the quality of output beam from monolithic microchip lasers

The dependence of the beam propagation factor (M ² parameter) with the absorbed pump power in the case of monolithic microchip laser under face-cooled configuration is extensively studied. Our investigations show that the M ₂ parameter is related to the absorbed pump power through two parameters (α and β) whose values depend on the laser material properties and laser configuration. We have shown that one parameter arises due to the oscillation of higher order modes in the microchip cavity and the other parameter accounts for the spherical aberration associated with the thermal lens induced by the pump beam. Such dependency of M ² parameter with the absorbed pump power is experimentally verified for a face-cooled monolithic microchip laser based on Nd³⁺ -doped GdVO₄ crystal and the values of α and β parameters were estimated from the experimentally measured data points.     

Quasi-three-level Nd:YVO<Subscript>4</Subscript> laser by diode pumping at 888 nm

We report efficient laser emission on the 914 nm ⁴ F _3/2 to ⁴ I _9/2 transition in Nd:YVO₄ under the pump with diode lasers at 888 nm for the first time. Continuous wave 6.57 W output power at 914 nm is obtained from a V-type resonator under 18.3 W of absorbed pump power; the slope efficiency with respect to the absorbed pump power was 60.6%. Moreover, intracavity frequency doubling with BiB₃O₆ (BiBO) nonlinear crystal yielded 1.77 W of deep-blue light at 457 nm with beam quality characterized by an M₂ factor of 1.25.     

High efficiency and good beam quality of electro-optic, cavity-dumped and double-end pumped Nd:YLF laser

In this paper, we describe a Nd:YLF laser based on high-speed RTP electro-optical cavity dumping technique. Two home-made 150 W fiber pump modules are used from both sides to pump Nd:YLF crystal. Coupling systems are the key elements in end-pumped solid-state lasers, the aberrations of which greatly affect the efficiency of the lasers. In order to get high efficient and good quality laser output, the optical software ZEMAX is used to design a four-piece coupling system. When the pumped energy is 32 mJ at the repetition rate of 1 Hz, the output energy is 6.5 mJ with 2.5 ns pulse width. When the pumped energy is 13.1 W at the repetition rate of 200 Hz, the output energy is 2.2 W with small M ² factor where M _x ² is 1.04, and M _y ² is 1.05, and the light-light conversion efficiency is up to 16.8%.     

M<Superscript>2</Superscript> of MOPA CuBr Laser Radiation

The beam propagation factor, M² of the master-oscillator power-amplifier (MOPA) CuBr laser emission compliant with ISO 11146 is studied methodically. Statistical parameters of 2D intensity profile of the near and far fields of MOPA laser radiation are measured by a beam analyzing technique as functions of timing delay between MO and PA. For first time the influence of the gas buffer (causing the radiation profile to change from annular to top-hat and Gaussian-like) and light polarization on CuBr laser beam focusability (M²) was under investigation. The MOPA gain curve is found and the influence of gain on the input signal (from MO into PA) due to the absorption/amplification in PA on the field profiles is shown. For annular radiation M² range is from 13–14 (small delays) to 5–6 (large delays) and for filled-center radiation M² is 6–7 (small delays) and at the end of gain curve is as much as 4. With polarized light, M² drops to 3 at the end of gain curve. The brightness of laser emission with hydrogen goes up 3–5 times and the linearly-polarized beam is at least 40% brighter than that of partial or non-polarized beams.     

高平均功率调Q准连续Nd:YAG激光器

通过选用低掺杂浓度的Nd:YAG晶体棒、热近非稳腔优化设计、双棒串接热致双折射补偿技术以及双Q开关正交放置结构，在LD抽运功率1116W时，实现调Q准连续全固态Nd:YAG激光器1064nm输出，平均功率达258W，光束质量M²～15.5，重复频率为10kHz，脉冲宽度为64ns，峰值功率达0.4GW，光光转换效率达23.1%. 关键词： Nd:YAG激光器 准连续波 激光二极管抽运 固体激光器     

The LD end-pumped Q-switched solid-state laser design software based on the adaptive method

In the LD end-pumped acousto-optic (A-O) Q-switched solid-state laser, according to the requirements of users on the laser peak power, the pulse width, the repetition rate and the beam quality factor M², if the main parameters of the pumping source and the laser resonator can be pre-designed by a software, will effectively guide experiments, and save cost. A kind of laser design software is introduced in this paper, which is based on the adaptive adjustment method and using MATLAB/C mixed programming. According to the user requirements, a compact LD end-pumped A-O Q-switched Nd:YAG laser which peak power is 100-kW-class can be designed and actual outputs can be calculated based on the design results. Drawing the laser pulse waveform, analyzing of the thermal effect in laser gain medium and drawing the temperature distribution map, exporting and saving the data are the additional functions of this software.     

Thermal lens determination of LD end-pumped solid-state laser with stable resonator by slit scanning method

A simple method to determine the thermal focal length of LD end-pumped solid-state laser with stable resonator is presented. The M² factor describing the quality of the beam can be obtained by scanning a slit through the multi-mode Gaussian beam field. The waist width of the beam and the corresponding TEM₀₀ under the same parameters of laser are then deduced through the law of multi-mode Gaussian beam propagation. Based on the standard matrix theory of stable resonator, the thermal focal length of the gain medium can be easily achieved. To show the application of this approach, the thermal focal length of an LD pumped Nd:YVO₄ laser is measured and the experimental results are in agreement with the theoretical prediction.     

Diode-pumped CW Nd<Superscript>3+</Superscript>:YAlO<Subscript>3</Subscript> laser at 1339 nm

A diode-pumped Nd³⁺:YAlO₃ (Nd:YAP) laser emitting at 1339 nm is described. At the incident pump power of 17.8 W, as high as 3.4 W of continuous-wave (CW) output power at 1339 nm is achieved. The slope efficiency with respect to the incident pump power was 23.6%. The output power stability over 60 min is better than 3.5%. The laser beam quality M ² factor is 1.33.