快速吸附与脱附的声表面波H2S传感器

本文主要研究了基于SnO₂/CuO薄膜的声表面波（SAW）传感器（室温下,工作频率约为147.8 MHz）检测H₂S气体的特性。以36°YXLiTaO₃为基片制作声表面波器件,通过采用射频磁控溅射法在其表面淀积SnO₂/CuO的复合薄膜制作出H₂S气体传感器。由场发射电子扫描电镜观察薄膜,薄膜连续均匀且表面分布大量微气孔,因而具有良好的吸附性。然后本文在85℃～205℃范围内对传感器的吸附和脱附速率、灵敏度及选择性等进行了实验研究。实验结果表明,所制备的传感器在较低温度下同时具备快速吸附和脱附特性,工作在190℃时气体吸附和脱附速率最快,检测20ppm H₂S的响应和恢复时间分别为30s、15s;工作在160℃时,传感器检测20ppmH₂S的灵敏度最高,工作频率变化约230 kHz,且对于低浓度2 ppm H₂S,频率变化可达45 kHz。同时,传感器也表现出良好的重复性和选择性。     

SnO2/Co3O4 nanofibers using double jets electrospinning as low operating temperature gas sensor

SnO₂/Co₃O₄nanofibers(NFs)are synthesized by using a homopolar electrospinning system with double jets of positive polarity electric fields.The morphology and structure of SnO₂/Co₃O₄hetero-nanofibers are characterized by using field emission scanning electron microscope(FE-SEM),transmission electron microscope(TEM),x-ray diffraction(XRD),and x-ray photoelectron spectrometer(XPS).The analyses of SnO₂/Co₃O₄NFs by EDS and HRTEM show that the cobalt and tin exist on one nanofiber,which is related to the homopolar electrospinning and the crystallization during sintering.As a typical n-type semiconductor,Sn O₂has the disadvantages of high optimal operating temperature and poor reproducibility.Comparing with Sn O₂,the optimal operating temperature of SnO₂/Co₃O₄NFs is reduced from 350℃to 250℃,which may be related to the catalysis of Co₂O₂.The response of SnO₂/Co₃O₄to 100-ppm ethanol at 250℃is 50.9,9 times higher than that of pure Sn O₂,which may be attributed to the p–n heterojunction between the n-type Sn O₂crystalline grain and the p-type Co₂O₂crystalline grain.The nanoscale p–n heterojunction promotes the electron migration and forms an interface barrier.The synergy effects between Sn O₂and Co₂O₂,the crystalline grain p–n heterojunction,the existence of nanofibers and the large specific surface area all jointly contribute to the improved gas sensing performance.     

Radiation induced chemisorption of oxygen on chromia

The effect of nuclear radiation on the chemisorption of oxygen on Cr₂O₃, Cr₂O₃-Al₂O₃ and Cr₂O₃-SnO₂ catalysts has been studied. An iodometric method was used to measure the amount of chemisorbed oxygen; simultaneously the increase in the catalytic activity of the catalyst in the decomposition of H₂O₂ was determined. It was found that the radiation present within a nuclear reactor promotes the chemisorption of oxygen on chromia (either pure or supported on Al₂O₃ or SnO₂) at temperatures at which such a chemisorption does not normally occur. The radiochemisorption of oxygen on chromia increases with the degree of dispersion of chromia on Al₂O₃ or SnO₂ and is accompanied by an increased catalytic activity of this catalyst in the decomposition reaction of H₂O₂. It seems that the radiochemisorption is largely due to the action of γ-rays and fast neutrons on the gas.     

不同Sb含量p-SnO2薄膜的制备和特性

采用化学气相沉积方法, 利用Sb₂O₃/SnO作为源材料, 在蓝宝石衬底上制备出不同Sb掺杂量的SnO₂薄膜, 并在此基础上制作出p-SnO₂:Sb/n-SnO₂同质p-n 结器件. 研究表明, 随着Sb含量的增加, 样品表面变得平滑, 晶粒尺寸逐渐增大, 且晶体质量有所改善, 发现少量Sb的掺入可以起到表面活化剂的作用. Hall测量结果证实适量Sb的掺杂可以使SnO₂呈现p型导电特性, 当Sb₂O₃/SnO的质量比为1:5时, 其电学参数为最佳值. 此外, p-SnO₂:Sb/n-SnO₂同质p-n结器件展现出良好的整流特性, 其正向开启电压为3.4 V.     

多孔ZnO微米球的制备及其优异的丙酮敏感特性

以六水合硝酸锌、尿素为原料,以六亚甲基四胺为表面活性剂,利用水热法合成了多孔氧化锌微米球.通过X射线衍射仪、扫描电子显微镜和吸附仪对样品的结构、形貌、比表面积和孔径进行了表征.利用所得多孔微米球氧化锌制备了气敏元件,并对其气敏特性进行了测试.结果表明:在280℃的工作温度下,表面多孔氧化锌微米球气敏元件对50 ppm的丙酮气体的灵敏度为26.8,响应时间和恢复时间分别约为4 s和10 s,并具有良好的选择性.     

Li-ion batteries: Phase transition

Progress in the research on phase transitions during Li+extraction/insertion processes in typical battery materials is summarized as examples to illustrate the significance of understanding phase transition phenomena in Li-ion batteries.Physical phenomena such as phase transitions(and resultant phase diagrams) are often observed in Li-ion battery research and already play an important role in promoting Li-ion battery technology. For example, the phase transitions during Li+insertion/extraction are highly relevant to the thermodynamics and kinetics of Li-ion batteries, and even physical characteristics such as specific energy, power density, volume variation, and safety-related properties.     

The adsorption of H2O on TiO2 and SnO2(110) studied by first-principles calculations

First-principles calculations based on density functional theory and the pseudopotential method have been used to investigate the energetics of H₂O adsorption on the (110) surface of TiO₂ and SnO₂. Full relaxation of all atomic positions is performed on slab systems with periodic boundary conditions, and cases of full and half coverage are studied. Both molecular and dissociative (H₂O→OH⁻+H⁻) adsorption are treated, and allowance is made for relaxation of the adsorbed species to unsymmetrica configurations. It is found that for both TiO₂ and SnO₂ an unsymmetrical dissociated configuration is the most stable. The symmetrical molecularly adsorbed configuration is unstable with respect to lowering of symmetry, and is separated from the fully dissociated configuration by at most a very small energy barrier. The calculated dissociative adsorption energies for TiO₂ and SnO₂ are in reasonable agreement with the results of thermal desorption experiments. Calculated total and local electronic densities of states for dissociatively and molecularly adsorbed configurations are presented, and their relation with experimental UPS spectra is discussed.     

Li修饰的C$lt;sub$gt;6$lt;/sub$gt;分子对H$lt;sub$gt;2$lt;/sub$gt;O的吸附研究

采用密度泛函理论中的广义梯度近似研究C₆Li吸附H₂O分子并将之进行分解的催化过程. 几何优化发现：Li原子最稳定的吸附位置是位于C 原子顶位上方. 研究表明,第一个H₂O 分子吸附在C₆Li上需要克服1.77 eV的能量势垒,然后分解为H和OH且与Li原子成键. 当吸附第二个H₂O分子时,第二个H₂O分子需要克服1.2 eV的能量势垒分解为H和OH,其中H与Li原子上的H原子结合成H₂,OH则替代Li 原子上的H结合在Li原子上. 因此C₆Li 可以作为催化剂将H₂O分子进行分解得到H₂. 分析可知：C₆Li主要是通过Li原子与H₂O之间形成的偶极矩作用来吸附H₂O 分子,与C₆₀Li₁₂ 的储氢机制类似. 研究结果可为储氢材料的制备提供一个新的思路. 关键词： 6')" href="#">C₆ Li 2O')" href="#">H₂O 密度泛函理论     

碳硼富勒烯衍生物C18B2M(M=Li,Ti, Fe)的储氢性能计算研究

本文使用密度泛函理论(density functional theory, DFT)中的广义梯度近似(generalized gradient approximation, GGA)研究了经碱金属原子Li、过渡金属原子Ti和Fe原子修饰的富勒烯C₁₈B₂M(M=Li, Ti, Fe)的储氢性能. 研究发现, C₁₈B₂由于B的替代掺杂, 比C₂₀对金属原子具有更高的结合能. 由平均吸附能分析可知: C₁₈B₂Li对H₂的吸附能力较弱, C₁₈B₂Fe对H₂的吸附能力过强, 而C₁₈B₂Ti对H₂的平均吸附能介于0.45-0.59 eV 之间, 介于物理吸附和化学吸附之间 (0.2-0.6 eV), 因此可以实现常温下的可逆储氢. C₁₈B₂M(M=Li, Ti, Fe)能够吸附的H₂数目最多分别为4, 6和4. 由储氢机理分析可知: C₁₈B₂Li主要通过碱金属离子激发的静电场来吸附H₂, 而C₁₈B₂Ti和C₁₈B₂Fe主要通过金属原子与H₂之间的Kubas作用来吸附H₂. 由于C₁₈B₂Ti既有较大的储氢数目, 又可以实现可逆储氢, 因此有望开发成新型纳米储氢材料.     

Anodic TiO2 nanotubes as anode electrode in Li–air and Li-ion batteries

We investigate the possibility of using a TiO₂ anode as an alternative to the Li electrode in Li–air and Li-ion rechargeable batteries. TiO₂ nanotube layer is fabricated by the anodization method and optional thermal treatment is conducted. The electrochemical charge/discharge profile of the TiO₂/liquid electrolyte/LiCoO₂ structured cell is measured under the flowing of O₂, N₂ and Ar, respectively. The elevation of the upper cut-off voltage from 3 to 4.5 V leads to an increase in the specific capacity by a factor of more than three. We suppose this to be a novel mechanism in which the TiO₂/LiCoO₂ system under the oxygen atmosphere works in Li–air battery mode up to 3 V and then works in Li-ion battery mode from 3 V to 4.5 V. This idea is confirmed by ICP-OES analysis.     

TiS2-graphene heterostructures enabling polysulfide anchoring and fast electrocatalyst for lithium-sulfur batteries: A first-principles calculation

Lithium-sulfur batteries have attracted attention because of their high energy density. However, the "shuttle effect" caused by the dissolving of polysulfide in the electrolyte has greatly hindered the widespread commercial use of lithium-sulfur batteries. In this paper, a novel two-dimensional TiS₂/graphene heterostructure is theoretically designed as the anchoring material for lithium-sulfur batteries to suppress the shuttle effect. This heterostructure formed by the stacking of graphene and TiS₂ monolayer is the van der Waals type, which retains the intrinsic metallic electronic structure of graphene and TiS₂ monolayer. Graphene improves the electronic conductivity of the sulfur cathode, and the transferred electrons from graphene enhance the polarity of the TiS₂ monolayer. Simulations of the polysulfide adsorption show that the TiS₂/graphene heterostructure can maintain good metallic properties and the appropriate adsorption energies of 0.98-3.72 eV, which can effectively anchor polysulfides. Charge transfer analysis suggests that further enhancement of polarity is beneficial to reduce the high proportion of van der Waals (vdW) force in the adsorption energy, thereby further enhancing the anchoring ability. Low Li₂S decomposition barrier and Li-ion migration barrier imply that the heterostructure has the ability to catalyze fast electrochemical kinetic processes. Therefore, TiS₂/graphene heterostructure could be an important candidate for ideal anchoring materials of lithium-sulfur batteries.     

Polyhedral silver clusters as single molecule ammonia sensor based on charge transfer-induced plasmon enhancement

The unique plasmon resonance characteristics of nanostructures based on metal clusters have always been the focus of various plasmon devices and different applications. In this work, the plasmon resonance phenomena of polyhedral silver clusters under the adsorption of NH₃, N₂, H₂, and CH₄ molecules are studied by using time-dependent density functional theory. Under the adsorption of NH₃, the tunneling current of silver clusters changes significantly due to the charge transfer from NH₃ to silver clusters. However, the effects of N₂, H₂, and CH₄ adsorption on the tunneling current of silver clusters are negligible. Our results indicate that these silver clusters exhibit excellent selectivities and sensitivities for NH₃ detection. These findings confirm that the silver cluster is a promising NH₃ sensor and provide a new method for designing high-performance sensors in the future.     

All-solid-state thick-film battery

An all-solid-state Li-ion secondary battery based on Li/LiSiPO/LiCoO₂ has been developed and the cell performance has been evaluated. The electrolyte and cathode were fabricated by tape casting. The charge and discharge behaviour of the cell at constant current was investigated in view of the fact of lower conductivities of solid conductors compared to liquid electrolytes and the internal resistance of the solid-solid interface. Solutions to these problems have been investigated by varying the fabrication methods. A major advantage was the application of pyrolyzable pore formers in the cathode green tape in order to produce a porous cathode matrix. This result indicates that the interfacial contacts between solid electrolytes and electrodes can be greatly improved. Also, the internal resistance may be further decreased by tape casting of thinner electrolyte films. In conclusion, the tape casting method is very promising for the development of high performance all-solid-state Li-ion batteries.     

单根SnO_2纳米线器件的电输运性能及其机理研究

为探究常态环境下氧空位对单根SnO_2纳米线电输运性能的影响,采用化学气相沉积法合成了SnO_2纳米线,通过光刻微加工技术构筑了Au/单根SnO_2纳米线/Au二端纳米器件.将单根SnO_2纳米器件进行氢化处理,测试其在空气与真空中的伏安特性曲线,发现单根SnO_2纳米线在空气和真空环境中呈现异常不同的电输运特性:在空气中,加偏压注入电子会使通过纳米器件的电流减小,Au电极与SnO_2纳米线之间的接触势垒增大;抽真空后,在偏压的影响下,通过纳米器件的电流增大,Au/SnO_2交界面的接触方式由肖特基接触转变成欧姆接触.实验分析表明,影响单根SnO_2纳米线电输运特性行为的因素与纳米线表面的氧原子吸附与脱吸附所引起的氧空位浓度的变化有关.为进一步分析氧空位浓度变化的作用,利用第一性原理计算方法计算了氧空位浓度对SnO_2纳米线电输运性能的影响,通过分析体系的能带结构、态密度及Au/SnO_2接触界面的I-V曲线和透射谱,发现随着氧空位浓度的增大,SnO_2纳米线的带隙变小.同时,氧空位缺陷使Au/SnO_2接触界面处电子透射率增大,体系电输运能力变强.该研究结果将为集成纳米功能器件的设计提供一种新思路.     

各Li吸附组分下硅烯氢存储性能的第一性原理研究

利用Li原子对硅烯进行表面修饰是提高硅烯氢存储能力的一种有效方法.为了充分挖掘Li修饰硅烯的氢存储性能,本文采用范德瓦耳斯作用修正的第一性原理计算方法,对不同Li吸附组分下硅烯的结构、稳定性和氢存储能力进行了研究.研究结果表明,硅烯体系能够在Li组分从0.11增加到0.50时保持稳定,其最大储氢量随Li组分的增加而增大,氢气平均吸附能则存在减小趋势;当Li组分达到0.50而饱和时,硅烯体系具有最大的储氢量,相应的质量储氢密度为11.46 wt%,平均吸附能为0.34 eV/H2,远高于美国能源部设定的储氢标准,表明提高Li组分甚至使其达到饱和在理论上能有效提高Li修饰硅烯的储氢性能.此外,通过对Mulliken电荷布居、差分电荷密度和态密度的分析,发现Li修饰硅烯的储氢机制与电荷转移诱导的静电相互作用和轨道杂化作用有关.研究结果可为Li修饰硅烯在未来氢存储领域的应用提供理论指导.     

合成温度和N2/O2流量比对碳纤维衬底上生长的SnO2纳米线形貌及场发射性能影响

采用化学气相沉积法系统研究了合成温度和N₂/O₂流量对生长在碳纤维衬底上的SnO₂纳米线形貌及场发射性能的影响规律. 利用扫描电镜(SEM)、透射电镜(TEM), X射线衍射(XRD)及能谱仪(EDS)对产物细致表征, 结果表明, SnO₂纳米线长径比随反应温度的升高而增大; 随N₂/O₂流量比值的增大先增大后变小, 场发射测试表明, 合成温度780 ℃, N₂/O₂流量比为300 : 3 时SnO₂纳米线阵列具有最佳的场发射性能, 开启电场为1.03 V/μm, 场强增加到1.68 V/μm时, 发射电流密度达0.66 mA/cm², 亮度约2300 cd/m².     

Li修饰的C24团簇的储氢性能

利用密度泛函理论研究了Li原子修饰的C₂₄团簇的储氢性能. Li原子在C₂₄团簇表面的最佳结合位是五元环. Li原子与C₂₄团簇之间的作用强于Li原子之间的相互作用, 能阻止它们在团簇表面发生聚集. 当Li原子结合到C₂₄表面时, 它们向C原子转移电子后带正电荷. 当氢分子接近这些Li原子时, 在电场作用下发生极化, 通过静电相互作用吸附在Li原子周围. 在Li修饰的C₂₄复合物中, 每个Li原子能吸附两到三个氢分子, 平均吸附能处于0.08到0.13 eV/H₂范围内. C₂₄Li₆能吸附12个氢分子, 储氢密度达到6.8 wt%.     

Neutron-based characterization techniques for lithium-ion battery research

During the past decades, Li-ion batteries have been one of the most important energy storage devices. Large-scale energy storage requires Li-ion batteries which possess high energy density, low cost, and high safety. Other than advanced battery materials, in-depth understanding of the intrinsic mechanism correlated with cell reaction is also essential for the development of high-performance Li-ion battery. Advanced characterization techniques, especially neutron-based techniques,have greatly promoted Li-ion battery researches. In this review, the characteristics or capabilities of various neutron-based characterization techniques, including elastic neutron scattering, quasi-elastic neutron scattering, neutron imaging, and inelastic neutron scattering, for the related Li-ion-battery researches are summarized. The design of in-situ/operando environment is also discussed. The comprehensive survey on neutron-based characterizations for mechanism understanding will provide guidance for the further study of high-performance Li-ion batteries.     

基于单粒子模型与偏微分方程的锂离子电池建模与故障监测

锂离子电池内部结构是一种复杂的分布参数系统, 如果为了降低计算难度而使用常微分方程描述锂离子电池, 可能会引入系统误差, 降低系统模型的可信度, 需要使用偏微分方程建立分布参数系统的精确模型. 本文提出了一种基于单粒子模型和抛物型偏微分方程的锂离子电池系统建模与故障监测系统设计方法, 当锂离子浓度实测值与理想值的残差大于预设门槛时判定分布参数系统处于故障状态. 通过一个仿真实例进行了锂离子电池系统建模和故障诊断实验, 实验证明基于单粒子模型和偏微分方程的锂离子电池故障监测系统具有更高的精确度和可信度.     

Ni/SnO_2复合薄膜的制备与光电性能

采用旋涂法将溶胶-凝胶法制备的Ni/Sn O2凝胶在玻璃基底上镀膜,得到了Ni/Sn O2复合薄膜,探讨了镍掺杂量、煅烧温度对薄膜结构和形貌的影响。通过X射线衍射、红外光谱、扫描电子显微镜等测试手段对Ni/Sn O2复合膜的结构和形貌进行表征。结果显示,500℃下煅烧的薄膜样品的结晶度较高,粒径小,颗粒分布均匀。用紫外-可见分光光度计和四探针电阻仪对其进行光学、电学性能测试,结果显示:适量的Ni掺杂可以提高Sn O2薄膜在近紫外光区的吸收,Ni/Sn O2薄膜在近紫外光区的吸收随着Ni2+掺杂摩尔分数从5%增加到10%而逐渐减小。当Ni2+掺杂摩尔分数为6%时,Ni/Sn O2复合薄膜的导电性能最好。