用于纳米粒子检测的双环谐振器（英文）

设计了一种可以探测单个纳米粒子的光学传感器结构,该结构由双环、双环间耦合区的通孔和直波导构成,并引入了Fano效应,进一步增强了粒子在光场中出现时的光耦合场变化.当纳米粒子穿过两个微环间的通孔时,其耦合系数和输出端的光强均发生变化,提出了一种基于双环谐振器结构的高精度耦合系数传感方法,通过检测双环谐振器耦合系数和输出端光强的变化对单体纳米粒子进行精确检测和计数.理论计算结果表明,在损耗为1dB/cm的情况下,与单环结构相比,双环结构的灵敏度提升了两个数量级.该双环结构在减小波导损耗的同时有效提升了检测灵敏度.     

耦合谐振器光波导旋转传感的相位灵敏度

利用光学谐振器结构的色散可提高旋转传感的灵敏度, 耦合谐振器光波导可实现强色散, 本文利用传输矩阵理论, 研究耦合谐振器光波导旋转传感的相位灵敏度, 讨论谐振器布局和波导参数对相位灵敏度的影响, 结果表明波导的相位曲线和相位灵敏度依赖于波导中谐振器的布局, 谐振器数量和耦合系数不仅会影响波导旋转传感相位灵敏度曲线峰值的数量和带宽, 还会影响相位灵敏度的大小, 而损耗会降低波导的相位灵敏度, 本文的结果可用于利用谐振器布局和波导参数设计耦合谐振器光波导的相位灵敏度, 对其在旋转传感方面的应用有重要意义. 关键词： 谐振器 旋转传感 光波导     

反馈式跑道型光学微环的传感灵敏度研究

提出了一种由U型反馈波导、跑道谐振腔和敏感环组成的反馈式跑道型光学微环传感器.采用耦合模理论推导了该传感器的归一化输出光强公式,数值分析了传输损耗因子、自耦合因子和敏感环尺寸对归一化输出光强的影响.分析表明:敏感环的损耗因子对归一化输出光强的调制作用明显,只要损耗因子发生微小变化,输出光强即发生较大变化;敏感环工作在弱耦合状态时传感灵敏度较高;敏感环的尺寸对传感灵敏度影响较大,适当地调整敏感环的大小可得到陡峭的输出光强谱线.对结构参数进行优化后不仅可以输出尖锐陡峭的非对称法诺谐振光强谱线,而且具有较高的法诺谐振光谱斜率,能更好地增强传感灵敏度.在信噪比为30dB的测量系统中,优化的反馈式跑道型光学微环传感器的探测极限达4.48×10-8单位折射率.     

温度测量范围加倍的单微环传感器

本文提出了一种基于U形波导耦合单微环结构的新型SOI(绝缘体上硅)温度传感器.温度变化引起感温部位有效折射率和长度变化,导致传感器的输出光谱发生漂移.根据传输矩阵法和耦合模理论,设计了新型传感器模型,并且分析了感温部位不同时系统输出光谱特性.结果表明:当U形波导耦合单微环整体结构感温时,输出光谱无伪模,消光比达到31 dB,可作为最佳感温元件.相比于传统的双直波导耦合单微环结构,当U形波导的两个耦合点间的距离为微环周长的整数倍数时,FSR(自由光谱范围)可加倍至56 nm,灵敏度提高到89.2 pm/?C,测量范围为298—720 K,实现了SOI微环谐振器的高温测量.     

串联双环光微谐振器的滤波特性

详细研究了串联双环光微谐振器的光带通滤波特性，给出了其通带带宽的公式，分析了出／入环光耦合系数和环间光耦合系数对通带特性的影响，计算并特别强调了滤波通带的结构特点，也分析了微环中存在的光损耗对串联双环光微谐振器的滤波特性的影响。     

损耗对串联双微环谐振器滤波特性的影响

对存在光损耗的串联双微环谐振器的滤波特性进行了研究.在理想耦合条件下,当环间耦合系数确定时,分析了光损耗的大小对主谐振峰的透过率、带宽、形状因子,以及伪模峰值透射率的影响,揭示了光损耗对滤波特性影响的规律.分析结果表明:主谐振峰和伪模的透射率随损耗的增大而下降,环与直波导间的耦合系数随损耗的增大而变小,而带宽和形状因子无明显变化|有损耗时环与直波导间的耦合系数不能过大也不能过小.     

垂直耦合结构纳米微环谐振器工艺失准分析

垂直耦合结构纳米微环谐振器是光子集成电路的重要组成单元.主要研究了与其实际制作相关的工艺失准问题.针对高折射率差波导材料垂直耦合结构纳米微环谐振器,先用耦合模理论解析方法研究了耦合系数与直波导和微环波导耦合层厚度d以及横向偏移量△之间的关系,为三维时域有限差分法(3D-FDTD)的精确数值计算确定了模拟范围.之后结合解...     

一种基于金刚石多层波导结构微环谐振器的仿真分析

提出了一种以金刚石新型材料为芯层的单微环谐振器模型.谐振器的纵切面采用五层脊形波导结构,中间一层设定为金刚石,上下两侧分别是SiO_2和As_2S_3,即As_2S_3-SiO_2-金刚石-SiO_2-As_2S_3.设置操作波长为1550 nm,依据耦合膜理论和微环谐振理论,利用Comsol软件仿真模拟了单直波导纵切面、直波导和环形波导耦合区的纵切面以及微环在谐振波长为1543 nm时的场强分布,及直波导和环形波导耦合区间距改变时微环的场强分布和传输特性.在此基础上,依据传输矩阵法讨论了微环的品质因数、耦合系数变化对输出光谱的影响,并对微环损耗进行了讨论.结果表明:以金刚石为芯层的微环谐振器具有良好的光学特性,本结构在谐振波长为1543 nm时谐振峰值达到了-12 dB以上,品质因数达到了1.54×10~5,在耦合系数为0.01时,自由光谱范围约为40 nm.     

马赫曾德环腔相位调制器的研究

为提高相位调制器的调制效率,结合单直波导光学环腔与带反馈的马赫曾德,提出用环形谐振腔等效为马赫曾德的上、下臂的新结构.采用耦合模理论推导了该模型的输出相位及归一化光强输出公式,数值分析了传输损耗因子、耦合角度对归一化输出光强及输出相位的影响.分析表明,输出光相位谱线随敏感环相位改变呈周期性变化,当耦合角度逐渐增大时,输出光相位谱线变尖锐,此时若要使输出相位产生π的相位差,敏感环的相位调制角度需较大.当传输因子较小时,相位谱线变化比较平缓,其最大值与最小值之间的差值不满足π的相位差.根据分析结果对结构参量进行优化,发现通过调节敏感环结构的耦合系数可以提高调制效率,仿真结果表明,当敏感环相位变化0.1π时,可以输出π的相位变化,同时归一化光强保持在0.9,满足了差分相移键控所需要的相位变化和信号幅度一致的要求,为进一步研究相位调制器提供理论依据.     

平面环形谐振腔微光学陀螺结构设计与优化

提出具有高群有效折射率的双环级联作为核心元件的谐振式平面光波导陀螺结构, 基于光学Sagnac原理得到了双微环耦合谐振式光学陀螺理论灵敏度与群有效折射率的一般表达式和双环与单环陀螺系统的灵敏度关系, 并由耦合模理论方法得到了双环系统耦合器的两个透射系数对应的群有效折射率变化情况. 在环腔半径R₁=R₂=100 μm、环腔传输损耗系数t₁=t₂=0.95的情况下, 针对环与环之间耦合器和环与波导之间耦合器透射系数对群有效折射率的不同影响, 得到了最大群有效折射率的产生条件. 采用文中参数(R=100 μm, t=0.95)计算的单环谐振式陀螺灵敏度为(10⁴-10⁵)°/h, 而双环级联谐振系统理论灵敏度能够达到10 °/h. 该研究对微环耦合谐振腔在角速度检测上的应用有重要的意义.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.