Molecular control over Ag/p-Si diode by organic layer

Electrical transport properties of Ag metal-fluorescein sodium salt (FSS) organic layer-silicon junction have been investigated. The current-voltage (I-V) characteristics of the diode show rectifying behavior consistent with a potential barrier formed at the interface. The diode indicates a non-ideal I-V behavior with an ideality factor higher than unity. The ideality factor of the Ag/FSS/p-Si diode decreases with increasing temperature and the barrier height increases with increasing temperature. The barrier height (φ_b=0.98 eV) obtained from the capacitance-voltage (C-V) curve is higher than barrier height (φ_b=0.72 eV) derived from the I-V measurements. The barrier height of the Ag/FSS/p-Si Schottky diode at the room temperature is significantly larger than that of the Ag/p-Si Schottky diode. It is evaluated that the FSS organic layer controls electrical charge transport properties of Ag/p-Si diode by excluding effects of the SiO₂ residual oxides on the hybrid diode.     

Comparison of electrical parameters of Zn/p-Si and Sn/p-Si Schottky barrier diodes

In this study, current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-semiconductor (MS) Zn/p-Si and Sn/p-Si Schottky diodes, with high resistivity silicon structures, are investigated. The parameters of series resistance (R_S), the ideality factor (n) and the barrier height (Φ_b) are determined by performing different plots from the forward bias current-voltage (I-V) and reverse bias capacitance-voltage (C-V) characteristics. Thus, the barrier heights (Φ_b) for the Si Schottky diodes obtained between 0.725 and 1.051 eV, the ideality factor (n) between 1.043 and 1.309, and the series resistance (R_S) between 12.594 and 12.950 kΩ. The energy distribution of interface states density was determined from the forward bias I-V characteristics by taking into account the bias dependence of the effective barrier height. It was concluded that the density of interface states in the considered energy range are in close agreement with each other values obtained for Zn/p-Si and Sn/p-Si Schottky diodes.     

Correlation between barrier heights and ideality factors of Cd/n-Si and Cd/p-Si Schottky barrier diodes

Our goal is to experimentally investigate whether or not the effective Schottky barrier heights (SBHs) and ideality factors obtained from the current-voltage (I-V) and capacitance-voltage (C-V) characteristics differ from diode to diode even if the samples were identically prepared. For this purpose, we prepared Cd/n-Si (33 dots) and Cd/p-Si (15 dots) diodes. The SBH for the Cd/n-Si diodes ranged from 0.701 to 0.605 eV, and ideality factor n from 1.913 to 1.213. Φ_b value for the Cd/p-Si diodes ranged from 0.688 to 0.730 eV, and ideality factor n value from 1.473 to 1.040. The experimental SBH distributions obtained from the C⁻²-V and I-V characteristics were fitted by a Gaussian function and their mean SBH values were calculated. Furthermore, the laterally homogeneous barrier heights were also computed from the extrapolation of the linear plot of experimental barrier heights versus ideality factors.     

Temperature dependence of the current-voltage characteristics of the Al/Rhodamine-101/p-Si(1 0 0) contacts

The current-voltage (I-V) characteristics of Al/Rhodamine-101/p-Si/Al contacts have been measured at temperatures ranging from 280 to 400 K at 20 K intervals. A barrier height (BH) value of 0.817 eV for the Al/Rh101/p-Si/Al contact was obtained at the room temperature that is significantly larger than the value of 0.58 eV of the conventional Al/p-Si Schottky diode. While the barrier height Φ_b0 decreases the ideality factors (n) become larger with lowering temperature. The high values of n depending on the sample temperature may be ascribed to decrease of the exponentially increase rate in current due to space-charge injection into Rh101 thin film at higher voltage. Therefore, at all temperatures, it has been seen that the I-V characteristics show three different regions, the ohmic behavior at low voltages, and the space charge limited current with an exponential distribution of traps at high voltages.     

The effect of interface states, excess capacitance and series resistance in the Al/SiO2/p-Si Schottky diodes

The current-voltage (I-V) characteristics of Al/SiO₂/p-Si metal-insulator-semiconductor (MIS) Schottky diodes were measured at room temperature. In addition the capacitance-voltage (C-V) and conductance-voltage (G-V) measurements are studied at frequency range of 10 kHz-1 MHz. The higher value of ideality factor of 3.25 was attributed to the presence of an interfacial insulator layer between metal and semiconductor and the high density of interface states localized at Si/SiO₂ interface. The density of interface states (N_ss) distribution profile as a function of (E_ss − E_v) was extracted from the forward bias I-V measurements by taking into account the bias dependence of the effective barrier height (Φ_e) at room temperature for the Schottky diode on the order of ≅4 × 10¹³ eV⁻¹ cm⁻²_. These high values of N_ss were responsible for the non-ideal behaviour of I-V and C-V characteristics. Frequency dispersion in C-V and G-V can be interpreted only in terms of interface states. The N_ss can follow the ac signal especially at low frequencies and yield an excess capacitance. Experimental results show that the I-V, C-V and G-V characteristics of SD are affected not only in N_ss but also in series resistance (R_s), and the location of N_ss and R_s has a significant on electrical characteristics of Schottky diodes.     

Current transport mechanism in Al/Si3N4/p-Si (MIS) Schottky barrier diodes at low temperatures

The current-voltage (I-V) and capacitance-voltage (C-V) characteristics of metal-insulator-semiconductor (Al/Si₃N₄/p-Si) Schottky barrier diodes (SBDs) were measured in the temperature range of 80-300 K. By using the thermionic emission (TE) theory, the zero-bias barrier height Φ_B0 calculated from I-V characteristics was found to increase with increasing temperature. Such temperature dependence is an obvious disagreement with the negative temperature coefficient of the barrier height calculated from C-V characteristics. Also, the ideality factor decreases with increasing temperature, and especially the activation energy plot is nonlinear at low temperatures. Such behaviour is attributed to Schottky barrier inhomogeneties by assuming a Gaussian distribution of barrier heights (BHs) at interface. We attempted to draw a Φ_B0 versus q/2kT plot to obtain evidence of a Gaussian distribution of the BHs, and the values of Φ_Bo = 0.826 eV and α_o = 0.091 V for the mean barrier height and standard deviation at zero-bias, respectively, have been obtained from this plot. Thus, a modified ln(I_o/T²) − q²σ_o²/2(kT)² versus q/kT plot gives Φ_B0 and Richardson constant A^* as 0.820 eV and 30.273 A/cm² K², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 30.273 A/cm² K² is very close to the theoretical value of 32 A/cm² K² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/Si₃N₄/p-Si Schottky barrier diodes can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights. In addition, the temperature dependence of energy distribution of interface state density (N_SS) profiles was determined from the forward I-V measurements by taking into account the bias dependence of the effective barrier height and ideality factor.     

Electronic and interface state density distribution properties of Ag/p-Si Schottky diode

Electronic and interface state distribution properties of Ag/p-Si Schottky diode have been investigated. The diode indicates non-ideal current-voltage behavior with an ideality factor greater than unity. The capacitance-voltage (C-V) characteristic is linear in reverse bias indicating rectification behavior and charge density within depletion layer is uniform. From I-V and C-V characteristics, junction parameters such as diode ideality factor and barrier height were found as 1.66 and ?_B(I-V) = 0.84 eV (?_B(C-V) = 0.90 eV), respectively. The interface state density N_ss and relaxation time τ of the Schottky diode were determined by means of Schottky capacitance spectroscopy method. The results show the presence of thin interfacial layer between the metal and semiconductor.     

Fabrication and electrical characterization of Au/p-Si/STO/Au contact

Au/STO/p-Si/Au structure is fabricated using pulsed laser deposition technique at room temperature. The current–voltage (I–V) characteristics of the device show rectification behavior. Various junction parameters such as ideality factor, barrier height and series resistance is determined using conventional forward bias I–V characteristics, Cheung method and Norde’s function. Au/STO/p-Si/Au structure shows non-ideal diode characteristics with the value of ideality factor of ∼5.1 and barrier height of ∼0.40 eV.     

Current conduction mechanism in Al/p-Si Schottky barrier diodes with native insulator layer at low temperatures

The forward bias current-voltage (I-V) characteristics of Al/p-Si (MS) Schottky diodes with native insulator layer were measured in the temperature range of 80-300 K. The obtained zero bias barrier height Φ_B0(I-V), ideality factor (n) and series resistance (R_s) determined by using thermionic emission (TE) mechanism show strong temperature dependence. There is a linear correlation between the Φ_B0(I-V) and n because of the inhomogeneties in the barrier heights (BHs). Calculated values from temperature dependent I-V data reveal an unusual behaviour such that the Φ_B0 decreases, as the n and R_s values are increasing with decreasing absolute temperature, and these changes are more pronounced especially at low temperatures. Such temperature dependence of BH is contradictory with the reported negative temperature coefficient of the barrier height. In order to explain this behaviour we have reported a modification in the expression reverse saturation current I_o including the n and the tunnelling factor (αΧ^1/2δ) estimated to be 15.5. Therefore, corrected effective barrier height Φ_bef.(I-V) versus temperature has a negative temperature coefficients (α = −2.66 × 10⁻⁴ eV/K) and it is in good agreement with negative temperature coefficients (α = −4.73 × 10⁻⁴ eV/K) of Si band gap. In addition, the temperature dependent energy distribution of interface states density N_ss profiles was obtained from the forward bias I-V measurements by taking into account the bias dependence of the Φ_e and n. The forward bias I-V characteristics confirm that the distribution of N_ss, R_s and interfacial insulator layer are important parameters that the current conduction mechanism of MS Schottky diodes.     

The barrier height inhomogeneity in Al/p-Si Schottky barrier diodes with native insulator layer

The current-voltage (I-V) characteristics of Al/p-Si Schottky barrier diodes (SBDs) with native insulator layer were measured in the temperature range of 150-375 K. The estimated zero-bias barrier height Φ_B0 and the ideality factor n assuming thermionic emission (TE) theory show strong temperature dependence. Evaluation of the forward I-V data reveals an increase of zero-bias barrier height Φ_B0 but decrease of ideality factor n with increase in temperature. The conventional Richardson plot exhibits non-linearity below 250 K with the linear portion corresponding to activation energy of 0.41 eV and Richardson constant (A^*) value of 1.3 × 10⁻⁴ A cm⁻² K⁻² is determined from intercept at the ordinate of this experimental plot, which is much lower than the known value of 32 A cm² K² for holes in p-type Si. Such behavior is attributed to Schottky barrier inhomogene ties by assuming a Gaussian distribution of barrier heights (BHs) due to barrier height inhomogeneities that prevail at interface. Also, Φ_B0 versus q/2kT plot was drawn to obtain evidence of a Gaussian distribution of the BHs, and values of Φ_B0 = 1.055 eV and σ₀ = 0.13 V for the mean BH and zero-bias standard deviation have been obtained from this plot, respectively. Thus, the modified versus q/kT plot gives Φ_B0 and A^* as 1.050 eV and 40.08 A cm⁻² K⁻², respectively, without using the temperature coefficient of the barrier height. This value of the Richardson constant 40.03 A cm⁻² K⁻² is very close to the theoretical value of 32 A K⁻² cm⁻² for p-type Si. Hence, it has been concluded that the temperature dependence of the forward I-V characteristics of the Al/p-Si Schottky barrier diodes with native insulator layer can be successfully explained on the basis of TE mechanism with a Gaussian distribution of the barrier heights.     

Controlling the electrical characteristics of Al/p-Si structures through Bi4Ti3O12 interfacial layer

In this study, the effects of high permittivity interfacial Bi₄Ti₃O₁₂ (BTO) layer deposition on the main electrical parameters; such as barrier height, series resistance, rectifying ratio, interface states and shunt resistance, of Al/p-Si structures are investigated using the current–voltage (I–V) and admittance measurements (capacitance–voltage, C–V and conductance–voltage, G/ω–V) at 1 MHz and room temperature. I–V characteristics revealed that, due to BTO layer deposition, series resistance values that were calculated by both Ohm's law and Cheung's method decreased whereas shunt resistance values increased. Therefore, leakage current value decreased significantly by almost 35 times as a result of high permittivity interfacial BTO layer. Moreover, rectifying ratio was improved through BTO interfacial layer deposition. I–V data indicated that high permittivity interfacial BTO layer also led to an increase in barrier height. Same result was also obtained through C–V data. Obtained results showed that the performance of the device is considerably dependent on high permittivity BTO interfacial layer.     

Al/Ti/4H-SiC Schottky barrier diodes with inhomogeneous barrier heights

This paper investigates the current-voltage (I-V) characteristics of Al/Ti/4H-SiC Schottky barrier diodes (SBDs) in the temperature range of 77 K-500 K,which shows that Al/Ti/4H-SiC SBDs have good rectifying behaviour.An abnormal behaviour,in which the zero bias barrier height decreases while the ideality factor increases with decreasing temperature (T),has been successfully interpreted by using thermionic emission theory with Gaussian distribution of the barrier heights due to the inhomogeneous barrier height at the Al/Ti/4H-SiC interface.The effective Richardson constant A =154 A/cm 2 · K 2 is determined by means of a modified Richardson plot ln(I 0 /T 2)-(qσ) 2 /2(kT) 2 versus q/kT,which is very close to the theoretical value 146 A/cm 2 · K 2.     

Effect of annealing on the electronic parameters of Au/poly(ethylmethacrylate)/n-InP Schottky diode with organic interlayer

A thin poly(ethylmethacrylate) (PEMA) layer is deposited on n-InP as an interlayer for electronic modification of Au/n-InP Schottky structure. The electrical properties of Au/PEMA/n-InP Schottky diode have been investigated by current–voltage (I–V) and capacitance–voltage (C–V) measurements at different annealing temperatures. Experimental results show that Au/PEMA/n-InP structure exhibit a good rectifying behavior. An effective barrier height as high as 0.83 eV (I–V) and 1.09 eV (C–V) is achieved for the Au/PEMA/n-InP Schottky structure after annealing at 150 °C compared to the as-deposited and annealed at 100 and 200 °C. Modified Norde's functions and Cheung method are also employed to calculate the barrier height, series resistance and ideality factors. Results show that the barrier height increases upon annealing at 150 °C and then slightly decreases after annealing at 200 °C. The PEMA layer increases the effective barrier height of the structure as this layer creates a physical barrier between the Au metal and the n-InP. Terman's method is used to determine the interface state density and it is found to be 5.141 × 10¹² and 4.660 × 10¹² cm^?2 eV^?1 for the as-deposited and 200 °C annealed Au/PEMA/n-InP Schottky diodes. Finally, it is observed that the Schottky diode parameters change with increasing annealing temperature.     

TiO2 Nanotube Array/Monolayer Graphene Film Schottky Junction Ultraviolet Light Photodetectors

Schottky junctions made from a titanium dioxide nanotube (TiO₂NT) array in contact with a monolayer graphene (MLG) film are fabricated and utilized for UV light detection. The TiO₂NT array is synthesized by the anodization and the MLG through a simple chemical vapor deposition process. Photoconductive analysis shows that the fabricated Schottky junction photodetector (PD) is sensitive to UV light illumination with good stability and reproducibility. The corresponding responsivity (R), photoconductive gain (G), and detectivity (D*) are calculated to be 15 A W^?1, 51, and 1.5 × 10¹² cm Hz^1/2 W^?1, respectively. It is observed that the fabricated PD exhibits spectral sensitivity and a simple power‐law dependence on light intensity. Moreover, the height of the Schottky junction diode is derived to be 0.59 V by using a low temperature I–V measurement. Finally, the working mechanism of the TiO₂NT array/MLG film Schottky junction PD is elucidated.     

Growth of InSe:Mn semiconductor crystals by Bridgman–Stockbarger technique and analysis of electron irradiation effects on Sn/InSe:Mn Schottky diodes

Mn-doped p-InSe semiconductor crystals were grown by Bridgman –Stockbarger technique. The crystals were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and fabricated Sn/InSe:Mn Schottky diodes. The current–voltage (I–V) and capacitance–voltage (C–V) measurements of diodes were investigated to determine the response of devices to electron irradiation with 9?MeV energy and 1.2?×?10¹⁰?e^??cm^?2 dose. After irradiation, the ideality factor and barrier height of the Sn/InSe:Mn Schottky diode were determined as 1.66 and 0.85?eV, respectively. Before irradiation, they were determined as 1.37 and 0.90?eV, respectively. It has been concluded that the radiation with high energy may contribute to form defects at the interface of the Sn/InSe:Mn device.     

Photovoltaic characteristics of Au/PVA (Bi-doped)/n-Si Schottky barrier diodes (SBDs) at various temperatures

The charge conduction properties of the Au/PVA (Bi-doped)/n-Si Schottky barrier diodes (SBDs) were investigated using current–voltage–temperature (I–V–T) measurements in dark and under various illumination levels. For this purpose, the main diode parameters such as reverse-saturation current (I_o), zero-bias barrier height (Φ_Bo), ideality factor (n), series resistance (R_s) and shunt resistance (R_sh) of diode were obtained as function of temperature and illumination level. Experimental results show that all of these electrical parameters are strong functions of illumination and temperature. The change in all electrical parameters becomes more important at low temperatures and illumination levels. While the n value decreases with increasing temperature and illumination level, Φ_Bo value increases. The fill factor (FF = V_m·I_m/V_oc·I_sc) values were obtained as 0.34 at 80 K and 0.40 at 320 K under 50 W and these values are near to a photodiode. Therefore, the fabricated diode can be used as a photodiode in optoelectronic applications. The forward bias I–V characteristics of the diode have also been explained by the space charge limited current (SCLC) model.     

Effect of MgZnO barrier layer on the UV emission of n-ZnO/p-Si heterojunction diodes

ZnO-based heterojunction light emitting diodes (LEDs) with MgZnO barrier layer had been fabricated on the p-Si substrate by metal-organic chemical vapor deposition (MOCVD) technology. The current-voltage (I-V) characteristics exhibited a typical p-n diode behavior. Both ultraviolet (UV) and visible emissions could be detected in the electroluminescence (EL) measurement. The result was compared with the EL spectrum of n-ZnO/p-Si heterojunction LED without MgZnO barrier layer. An improved light extraction efficiency by about 31% was realized owing to the current-blocking effect of MgZnO layer. The result indicated that MgZnO barrier layer can prevent the electrons as expected and realize electron-hole recombination in ZnO layer effectively.     

Laterally inhomogeneous barrier analysis of the methyl violet/p-Si organic/inorganic hybrid Schottky structures

In this work, we have investigated the electrical characteristics, such as current-voltage (I-V) and capacitance-voltage (C-V) measurements, of identically prepared crystal violet/p-Si Organic/Inorganic (OI) Schottky structures formed by evaporation of organic compound solution to directly p-Si semiconductor substrate. It has been seen that the crystal violet organic dye thin film on the p-Si substrate has exhibited a good rectifying behavior. The barrier heights (BHs) and ideality factors of all devices have been calculated from the electrical characteristics. Although the diodes were all identically prepared, there was a diode-to-diode variation: the effective barrier heights ranged from 0.6 ± 0.1 to 0.8 ± 0.1 eV, and the ideality factor from 1.6 ± 0.4 to 3.5 ± 0.4. The barrier height versus ideality factor plot has been plotted for the OI devices. Lateral homogeneous BH was calculated as a value of 0.7 eV from the observed linear correlation between BH and ideality factor, which can be explained by laterally inhomogeneities of BHs. The values of barrier height and acceptor doping concentration yielded from the reverse bias C-V measurements ranged from 0.7 ± 0.1 to 1.3 ± 0.1 eV and from (4.7 ± 0.8) × 10¹⁴ to (8.1 ± 0.8) × 10¹⁴ cm⁻³, respectively. The mean barrier height and mean acceptor doping concentration from C-V characteristics has been calculated 1.0 eV and 5.9 × 10¹⁴ cm⁻³, respectively. It has been seen that the mean BH value of 0.7 eV obtained for the Al/methyl violet/p-Si contact is significantly larger than BH values of the conventional Al/p-Si Schottky diodes. Thus, modification of the interfacial potential barrier for metal/Si diodes has been achieved using a thin interlayer of the methyl violet organic semiconductor; this has been ascribed to the fact that the methyl violet interlayer increases the effective barrier height by influencing the space charge region of Si.     

Investigation of electrical and photovoltaic properties of Au/poly(propylene glycol)-b-polystyrene/n-Si diode at various illumination intensities

Electrical and photovoltaic properties of Au/poly(propylene glycol)-b-polystyrene/n-Si diode were investigated under various illumination intensities. Field emission scanning electron microscope micrographs of the interfacial polymer layer were provided for verification of the nano-fibre pattern. The current–voltage (I–V) measurements of the diode in the dark and under various illumination intensities (50–250?mW/cm²) were carried out and the main electrical parameters of the diode such as leakage current (I₀), ideality factor (n), zero-bias barrier height (Φ_B0), series and shunt resistance (R_s and R_sh), density of surface states (N_ss), open circuit voltage (V_oc) and short-circuit current (I_sc) were obtained in these conditions.     

Thermal stability of tungsten and tungsten nitride Schottky contacts to AlGaN/GaN

Thin tungsten nitride (WNx) films were produced by reactive DC magnetron sputtering of tungsten in an Ar-N2 gas mixture. The films were used as Schottky contacts on AlGaN/GaN heterostructures. The Schottky behaviours of WNx contact was investigated under various annealing conditions by current-voltage (I-V ) measurements. The results show that the gate leakage current was reduced to 10-6 A/cm2 when the N2 flow is 400 mL/min. The results also show that the WNx contact improved the thermal stability of Schottky contacts. Finally, the current transport mechanism in WNx/AlGaN/GaN Schottky diodes has been investigated by means of I-V characterisation technique at various temperatures between 300 K and 523 K. A TE model with a Gaussian distribution of Schottky barrier heights (SBHs) is thought to be responsible for the electrical behaviour at temperatures lower than 523 K.