Yb3+敏化的Er3+/Ho3+共掺碲酸盐玻璃的上转换发光研究

用高温熔融法制备了系列Er³⁺/Yb³⁺共掺，Ho³⁺/Yb³⁺共掺，和Er³⁺/Yb³⁺/Ho³⁺三掺碲酸盐玻璃，在975nm激光抽运下三种掺杂玻璃中都出现了较强的绿光和红光上转换.研究了Yb³⁺离子对Er³⁺和Ho³⁺离子上转换发光强度的影响以及Yb³⁺→Er关键词： 3+/Yb³⁺/Ho³⁺共掺')" href="#">Er³⁺/Yb³⁺/Ho³⁺共掺 碲酸盐玻璃 光谱性质 上转换     

全光纤超短脉冲掺Yb3+光纤环形激光器

讨论了自启动被动锁模掺Yb³⁺光纤环形激光器产生短脉冲的机理，并研制出全光纤结构超短脉冲掺Yb³⁺光纤环形激光器.采用两个976nm半导体激光器级联抽运作为抽运源，高掺杂浓度掺Yb³⁺光纤作为增益介质，利用光纤的非线性偏振旋转效应，得到自启动、十分稳定的ps量级锁模光脉冲.激光器锁模阈值功率260mW，输出功率25mW，锁模光脉冲中心波长1056nm，3dB带宽11.7nm，重复频率20MHz.与其他结构光纤激光器相比，这种全光纤结构具有更高的效率和更好的稳定性. 关键词： 环形光纤激光器 3+光纤')" href="#">高掺杂浓度掺Yb³⁺光纤 自启动 被动锁模     

高功率光子晶体光纤放大器实验研究

利用掺Yb³⁺的光子晶体光纤作为光纤放大器的增益介质,采用反向抽运方式,分别从理论和实验方面研究了不同信号的增益特性,在信号光功率为6W,抽运光功率为160W时,获得了104W的输出功率.实验发现,当抽运功率大于一定值时,放大器输出会有一定的不稳定性,并影响输出功率的进一步提高. 关键词： 光子晶体光纤 光纤放大器 反向抽运 高功率     

Er/Yb共掺硅酸盐玻璃的光致发光

采用固相反应方法，制备了Er³⁺离子浓度为0.5 at.%，Yb掺杂浓度范围为0.0— 6.0 at.%的Er/Yb共掺激光玻璃，并对激光玻璃的吸收光谱和光致荧光光谱进行了分析.研究 结果显示，Yb³⁺掺杂对Er³⁺在980 nm附近的吸收起到了非常显著的 增强作用.在 980 nm的激光抽运下，激光玻璃在1530 nm处的光致发光强度随着Yb离子浓度 的增加而先增大后减小， 当Yb³⁺离子浓度为Er³⁺离子浓度6倍时光 致发光强度达到最大值.同时还发现了Yb³⁺对Er³⁺的光致荧光光谱 的展宽作用，并讨论了荧光光谱的展宽机理. 关键词： Er/Yb共掺玻璃 光致发光 吸收光谱     

利用光谱滤波器实现自启动的全光纤超短脉冲掺Yb3+光纤激光器

讨论了利用光谱滤波器实现自启动的被动锁模掺Yb³⁺光纤环形激光器的锁模机理,并研制出全光纤结构超短脉冲掺Yb³⁺光纤环形激光器.使用980 nm二极管激光器作为抽运源,高掺杂浓度掺Yb³⁺光纤作为增益介质.在净群速度色散为正的环形腔中加入光谱滤波器,抑制Yb³⁺离子在1030 nm强发射峰的同时,通过对啁啾脉冲的光谱滤波实现脉冲压缩.光谱滤波器与光纤非线性偏振旋转效应相结合,实现了激光器在1053 nm可自启动、十分稳定的锁模运转.激光器锁模阈值功率300 mW,平均斜率效率18.3%,最大输出功率53.07 mW,对应最大输出脉冲能量3.2 nJ.锁模光脉冲中心波长1053.6 nm,3 dB带宽10.84 nm,重复频率16.45 MHz.锁模脉冲宽度为皮秒量级,经腔外光栅对压缩至188 fs. 关键词： 3+光纤激光器')" href="#">掺Yb³⁺光纤激光器 自启动锁模 全光纤     

掺铒光波导入大器的速率方程分析

用重合积分的方法，分析了描述掺铒光波导放大器（EDWA）的速率方程，得到了980nm波段抽运的掺铒光波导放大器增益的隐式解析解，在此基础上得到了抽运阈值功率的解析表达式。计算了掺铒平面光波导放大器中的光场与铒掺杂浓度分布的重叠因子。讨论了铒掺杂浓度对抽运阈值功率的影响及轴运功率对增益的影响。     

掺铒锆钛酸铅镧陶瓷的上转换动力学分析

测量了掺铒锆钛酸铅镧(Er³⁺:PLZT)陶瓷的吸收光谱和上转换荧光光谱,利用Er³⁺:PLZT的吸收光谱,计算Er³⁺离子的辐射跃迁概率. 分析了980nm 激发下 Er³⁺:PLZT 的上转换荧光光谱,观察到明显的上转换荧光,且峰值位于540,564nm附近的绿色荧光带比 678nm 附近的红色荧光带强. 建立了Er³⁺离子跃迁的速率方程,通过求解速率方程并采用拟合荧光衰减实验曲线的方法,得出 关键词： 频率上转换 3+离子')" href="#">Er³⁺离子 锆钛酸铅镧陶瓷 速率方程     

掺铒光波导放大器的速率方程分析

用重合积分的方法 ,分析了描述掺铒光波导放大器 (EDWA)的速率方程 ,得到了 980nm波段抽运的掺铒光波导放大器增益的隐式解析解 ,在此基础上得到了抽运阈值功率的解析表达式。计算了掺铒平面光波导放大器中的光场与铒掺杂浓度分布的重叠因子。讨论了铒掺杂浓度对抽运阈值功率的影响及抽运功率对增益的影响。     

基于偏振保持掺Er3+光纤的高稳定性单波长光纤激光器

研制出光敏偏振保持掺Er³⁺光纤,通过在这种光纤上紫外写入三个光纤光栅,形成对抽运激光高转化效率的谐振腔.在输出功率为23.617dBm、工作波长为976nm的激光抽运下,得到均值功率为9.20dBm、均值中心波长为1554.554nm的单波长激光输出.在室温下800min（约13.3h）的测量时间内,其输出功率的波动为±0.05dB,中心工作波长的波动为±0.0015nm. 关键词： 光纤激光器 3+光纤')" href="#">偏振保持掺Er³⁺光纤 光纤Bragg光栅     

双向掺铒光纤放大器的特性分析

讨论了双向掺铒光纤放大器的结构方案,利用考虑放大的自发辐和北员耗影响的双向掺铒光纤放大器稳态放大速率方程模型分析的增益与掺铒光纤长度、输入信号光功率、帛运光功率及抽运方式等参数之间的关系,研究了单向和双向等功率抽运下正反向噪声系数随正反向信号光输入功率的变化行为。     

Numerical investigation of gain characteristics of Er3+/Yb3+ co-doped fiber amplifiers

In this work, a model for analyzing the gain characteristics of heavily Er³⁺/Yb³⁺ co-doped compact fiber amplifier is presented. Four-level rate equations and finite-difference beam propagation method are applied to simulate the optical field evolution along the active fiber. Based on this model, the influences of ion concentration, fiber length and pump power on the gain characteristics of Er³⁺/Yb³⁺ co-doped phosphate glass fiber amplifiers are theoretically investigated. Numerical results show that for a fiber length of 3.6 cm the internal gain can reach 27.2 dB with N _Er = 2.6 × 10²⁶ ions/m³ and N _Yb = 1.2 × 10²⁷ ions/m³ when pumped with 224 mW at 980 nm. The gain per centimeter is 7.56 dB/cm. The results can provide useful information to optimize the gain performance of these compact fiber amplifiers.     

Efficient Fibre Amplifiers Based on a Highly Er3＋/Yb3＋ Codoped Phosphate Glass-Fibre

Highly Er3＋ /yb3＋-codoped single-mode phosphate glass fibre is fabricated by the rod-in-tube technique. The performances of high-concentration Er3＋ /yb3＋-codoped phosphate glass fibre amplifiers are investigated and discussed. An efficient optical fibre amplifier with a gain of 12.6 dB based on a 3.0 cm long Era＋ /ybe＋-codoped phosphate glass fibre is demonstrated under a dual-pump configuration with two 976 nm fibre-pigtail laser diodes, which make it attractive for compact Er3＋-doped fibre amplifiers. The obtedned noise figures of signal wavelength from 1525 to 1565nm are less than 6.0dB. Gain saturation behaviour at 1535nm is also investigated, and the obtained saturation output power is larger than 10 dBm.     

输出平均功率大于2W的高功率、包层抽运、超短脉冲铒镱共掺光纤激光器

采用主振荡功率放大的方式，研制成功集宽带波长连续可调谐、带宽内输出功率谱均衡、高重复频率和高功率性能于一体的超短脉冲包层抽运铒镱共掺光纤激光器.将优化主振荡器和功率放大器的腔结构与掺铒光纤的饱和增益特性结合起来，实现了1535nm—1570nm(35nm带宽)的输出功率均衡的波长连续可调谐激光输出，在带宽内激光功率的最大波动仅为0.5dBm；带宽内平均输出功率大于2W、脉冲重复频率大于10GHz、脉冲宽度小于30ps.该激光器具有综合性能指标先进、结构简单、全光纤化、使用方便等优点. 关键词： 光纤激光器 包层抽运 短脉冲 高重复频率     

Yb3+sensitized Er3+-doped waveguide amplifiers: a theoretical approach

Silicate and phosphate glass waveguide amplifiers doped with Er³⁺, and co-doped with Er³⁺/Yb³⁺ are theoretically studied. Configurations for core and core–cladding doped waveguide amplifiers are considered. It is shown that gain in the core–cladding doped amplifiers is considerably higher than core doped amplifiers. It is also shown that with input signal power up to 1 and 200mW pump power, a 12.5dB gain can be achieved in a 3cm long waveguide amplifier, with a noise figure of 3dB.     

Amplifying Characteristics of Er3+/Yb3+ Co-Doped Parallel-Cascaded Double Microring Resonators

Abstract

In terms of the coupled mode theory, formulas of the transfer function and the output power gain are presented for an Er³⁺/Yb³⁺ co-doped parallel-cascaded double microring resonator. Around the pump wavelength of 0.98 μm and the central signal wavelength of 1.55 μm, analysis is performed for the dependence of the output power gain on the pump power, signal power, dopant concentration, amplitude coupling ratio, and ring spacing. The results show that the output power gain of this device is much larger than that of the Er³⁺/Yb³⁺ co-doped waveguide amplifier with identical waveguide lengths. In the case of the amplitude coupling ratio κ = 0.064, ring spacing L₂ = 10π R, pump power P_p0 = 8 mW, signal power P_s0 = 37.2 μW, Er³⁺ ion concentration N_Er = 1 × 26 m^?3, and Yb³⁺ ion concentration N_Yb = 3 × 27 m^?3, the device can produce higher signal power gain from 11.9 dB even up to 70 dB.     

Spectroscopic properties in Er Er3+/Yb3+Co-doped fluorophosphate glass

Using the technique of high-temperature melting, a new Er³⁺/Yb³⁺ co-doped fluorophosphate glass was prepared. The absorption and fluorescence spectra were investigated in depth. The effect of Er³⁺ and Yb³⁺ concentration on the spectroscopic properties of the glass sample was also discussed. According to the Judd-Ofelt theory, the oscillator strength was computed. The lifetime of ⁴I_13/2 level (τ_m) of Er³⁺ ions was 8.23 ms, and the full width at half maximum of the dominating emission peak was 68 nm at 1.53 τ_m. The large stimulated emission cross section of the Er³⁺ was calculated by the McCumber theory. The spectroscopic properties of Er³⁺ ion were compared with those in different glasses. The full width at half maximum and σ_e are larger than those of other glass hosts, indicating this studied glass may be a potentially useful candidate for high-gain erbium-doped fiber amplifier.     

Up-conversion photoluminescence characteristics of Yb3+:Er3+:Tm3+ co-doped borosilicate glasses

Yb3+:Er3+:Tm3+ co-doped borosilicate glasses are prepared.Their strong up-conversion photoluminescence spectra in a range from ultra-violet to near-infrared,which are excited by a 978-nm laser diode,are measured,and the mechanisms of energy transfer among Yb3+,Er3+ and Tm3+ ions are discussed.The results show that there is an unexpected wavelength at 900-nm emission from Yb3+ Stark splitting levels to pump Tm3+ ions and there exists an optimum pump power.The concentration of the Tm3+ dopant gives rise to a prominent effect on the intensity of visible and near-infrared emissions for the Yb3+:Er3+:Tm3+ co-doped borosilicate glasses.     

Er3+及Er3+/Yb3+共掺铋酸盐玻璃光谱性质研究

制备了Er³⁺及Er³⁺/Yb³⁺共掺铋酸盐玻璃，测试了样品的吸收光谱、荧光光谱.应用Judd-Oflet理论计算了Er³⁺在铋酸盐玻璃中的光谱强度参数，分别为Ω₂=(5.47—2.92)×10^-20cm²，Ω₄=(2.16—1.22)×10^-20cm², 关键词： 3+')" href="#">Er³⁺ 铋酸盐玻璃 3+/Yb³⁺共掺')" href="#">Er³⁺/Yb³⁺共掺 光谱性质     

铋镓共掺的高浓度掺铒石英基光纤中铒离子团簇率的实验研究

使用MCVD法结合溶液掺杂技术制作了铒铋镓共掺的石英基光纤.根据光纤吸收谱,得出其中铒离子浓度是5.24×10²⁵/m³.然后提出了一种新的利用透射率测定掺铒光纤的团簇率的实验方法,该方法相比于以前的方法更简单有效.利用该方法,测得了自制铒铋镓共掺光纤中团簇率.通过与前人的结果相比较,充分说明铋和镓的掺入大大提高了铒离子在石英基光纤中的溶解度,抑制了铒离子形成团簇. 关键词： 掺铒光纤 石英基光纤 团簇 高浓度     

铋镓共掺的高浓度掺铒石英基光纤中铒离子团簇率的实验研究

使用MCVD法结合溶液掺杂技术制作了铒铋镓共掺的石英基光纤.根据光纤吸收谱，得出其中铒离子浓度是5.24×10²⁵/m³.然后提出了一种新的利用透射率测定掺铒光纤的团簇率的实验方法，该方法相比于以前的方法更简单有效.利用该方法，测得了自制铒铋镓共掺光纤中团簇率.通过与前人的结果相比较，充分说明铋和镓的掺入大大提高了铒离子在石英基光纤中的溶解度，抑制了铒离子形成团簇.