HLS-Ⅱ直线加速器能量调节及应用

为了高效地对直线加速器输出束流能量进行调节,设计了合肥光源（HLS-II）直线加速器束流能量调节方案。该方案在调试阶段通过能谱分析系统观察束团状态并测量束流能量,储存环注入阶段使用3个束流位置探测器（BPM）对束流能量进行在线测量;使用自动相位扫描程序对速调管输出相位进行扫描,获得各加速段的能量增益公式;定量调节速调管的输出相位和高压,实现直线加速器输出束流能量的快速调节。在线应用结果表明,该方案能快速实现束流能量调节,调节后的束流具有良好品质,束流横向能散小于0.22%,注入速率明显改善。     

BEPCⅡ直线加速器的束流调试和稳定运行

BEPCⅡ重大改造工程要求将对撞机的峰值亮度提高近百倍,并具有高积分亮度,为此必须对作为注入器的直线加速器进行重大改造,提供高能、强流、小发射度和小能散度的正负电子束,达到高注入速率(正电子50mA/min.)的要求.这对直线加速器各系统和束流调试是一个挑战.在成功建造了新电子源、新正电子源、新微波功率源、相位控制系统和束流轨道测量系统等的基础上,着重叙述了束流参数的调试结果,束流能量、能散度、发射度、传输效率均达到(或优于)设计指标.描述了束流参数稳定性的研究、改进和成功地达到稳定运行.最后简述了新建中的次谐波聚束系统,以进一步提高束流性能和注入速率.     

BEPCⅡ直线加速器的束流调试和稳定运行

BEPCⅡ重大改造工程要求将对撞机的峰值亮度提高近百倍, 并具有高积分亮度, 为此必须对作为注入器的直线加速器进行重大改造, 提供高能、强流、小发射度和小能散度的正负电子束, 达到高注入速率(正电子50mA/min.)的要求. 这对直线加速器各系统和束流调试是一个挑战. 在成功建造了新电子源、新正电子源、新微波功率源、相位控制系统和束流轨道测量系统等的基础上, 着重叙述了束流参数的调试结果, 束流能量、能散度、发射度、传输效率均达到(或优于)设计指标. 描述了束流参数稳定性的研究、改进和成功地达到稳定运行. 最后简述了新建中的次谐波聚束系统, 以进一步提高束流性能和注入速率.     

BTF加速器物理设计

北京X射线自由电子激光试验装置(BTF)将“寄生”在BEPCⅡ直线注入器这一国内能量最高, 性能最好的电子直线加速器上.BTF将弃用现有直流枪予注入器, 采用光注入器(photoinjector)经低能输运线斜注入到BEPCⅡ直线加速器主加速器, 同时拆掉三节加速管以安装两级磁压缩器, 并在A46后拆掉二节加速管引出束流, 经高能输运线后进入波荡器.模拟结果表明改造后的直线加速器BTF电子能量可达1.18GeV、能散0.15%、归一化发射度小于2.5mm.mrad.     

北京散裂中子源RCS注入系统物理设计和研究

北京散裂中子源(BSNS)的主加速器——快循环同步加速器(RCS)采用H^－剥离注入方法, 将从直线加速器预加速的束流进行累积和进一步加速. 束流损失率的控制是该类高功率质子加速器所面临的关键问题之一, 而束流损失中很重要的部分是由空间电荷效应造成的. 为了减小该类束流损失, 注入系统设计中利用H^－剥离注入和相空间涂抹方法将直线加速器预加速的发射度较小的束流尽可能均匀地涂抹到较大的横向相空间中. 与其他的类似加速器相比, RCS注入系统将所有注入元件放在一个长为9m的无色散漂移节中以充分节省RCS环的纵向空间, 并使对注入系统的操作与对RCS主体的操作完全独立. 对于RCS累积的粒子数1.9×10¹³, 空间电荷效应对粒子的运动有非常重要的作用, 本文介绍了采用ORBIT程序进行三维模拟计算并进行设计优化的结果. 还介绍了系统设计时需要考虑的其他重要因素, 如质子穿越、电子收集等.     

CSNS RCS注入横向相空间涂抹的研究

中国散裂中子源(CSNS)加速器系统由80MeV的直线加速器和1.6GeV的快循环同步加速器(RCS)构成. CSNS第一阶段采用H^－剥离注入方法, 将粒子数累积至1.88×10¹³. 注入束流被涂抹在较大的横向相空间内, 以减小空间电荷效应. 粒子注入后, 为了降低由空间电荷效果引起的工作点漂移和工作点弥散, 束流分布的均匀性很重要. 引入了评估束流分布均匀性的三个参数. 为了抑制注入过程中束流发射度和束晕的增长, 通过采用三维的模拟程序ORBIT, 对不同的横向相空间涂抹方案进行了比较. 同时还介绍了工作点、注入峰值流强和斩波调制比等因素对注入过程的影响.     

高能同步辐射光源直线加速器初期调束取得重要进展

高能同步辐射光源（HEPS）是中国第一台第四代高能同步辐射光源,其加速器由直线加速器、增强器、储存环及输运线组成。报道了HEPS直线加速器的初期束流调试重要进展。HEPS直线加速器是一台500 MeV S波段常温直线加速器,由热阴极电子枪、聚束系统、主直线加速器构成。在按时完成设备加工、安装和老练的基础上,于2023年3月9日启动束流调试,当天实现束流全线贯通。3月14日束流能量达到500 MeV,束团电荷量达到2.5 nC。经过测量,直线加速器出口束流能散0.4%,能量稳定度0.06%,水平和垂直几何发射度分别为233 nm和145 nm。目前直线加速器束团电荷量可达到7.0 nC,相关束流调试正在进行。     

利用电压异步调节束流能散度

对直线感应加速器加速电压的同步性对束流能散度的影响进行了分析,结果表明:考虑束流负载效应后,束流的不同部分将得到不同的能量增益,前后沿部分相对于平顶部分得到更多的能量增益,从而在一定程度上增加整个束流的能散度,限制了加速器光源尺寸的进一步减小。因此,提出利用调节加速电压异步的方法来调节束流不同部分得到的能量增益,从而在一定程度上降低整个束流脉宽期间的能散度。初步的试验结果也证明,加速电压的异步调节可以明显改变束流整体的的能散度。     

HIRFL-SFC采用平顶波加速的模拟研究

近代物理研究所针对改善兰州重离子加速装置注入器(HIRFL-SFC)引出束流的品质,将主要考虑改进高频系统以提高Dee盒的加速电压、增加一个相位狭缝和采用平顶波加速等。其中采用平顶波加速可以有效地减小扇形聚焦回旋加速器(SFC)引出束流的能散并且提高其自身的传输效率。采用回旋加速器束流模拟程序AGORA对SFC进行模拟计算,并比较有无平顶波加速系统下束流品质的变化。结果表明,采用平顶波加速后,SFC的引出束流能散明显减小,而且在引出偏转板入口处束流的径向尺寸及圈间距满足单圈引出的条件。     

高能光源增强器束流横向尺寸测量系统设计

高能同步辐射光源的增强器将直线加速器注入的束流加速到储存环所需的能量,为储存环提供高品质的电子束。为了对增强器的束流横向截面尺寸、发射度及能散进行测量,设计了两条可见光-紫外波段的束测光束线。两条光束线分别选取无色散和色散较大的两处弯铁位置作为光源点,使用两套同步光成像系统来监测光源点的束流截面尺寸,并计算束流发射度及能散。介绍了同步光引出真空室及光学成像系统,对影响成像质量的空间分辨率进行了分析,并针对升能过程中不同能量下束流光斑变化的测量进行了设计。     

BEPCII Injector Linac Upgrade and Beam Instabilities

The upgrade project of the Beijing Electron Positron Collider （BEPCII） and its injector linac is working well. The linac upgrade aims at a higher injection rate of 5OmA/min into the storage ring, which requires an injected beam with low emittance, low energy spread and high beam orbit and energy stabilities. This goal is finally reached recently by upgrading the linac components and by dealing with rich and practical beam physics, which are described in this study.     

The Effect of High Spatial Harmonics in RF Linac

The effect of high spatial harmonics on beam dynamics in a axisymmetric radio frequency linear accelerator (RF linac) is examined. The high spatial harmonics forms the second order ponderomotive focusing for the relativistical particle beam when the transverse motion is averaged over the period of RF structure, the beam transverse envelop equation is obtained including the ponderomotive focusing force which is useful for the design of RF gun and linac. Under a certain of high spatial harmonics coefficients, the high spatial harmonics increase the energy spread due to the stochasitical beam energy diffusion.     

Towards one machine, two purposes: using a common SC linac for XFEL and ERL simultaneously

The linac based XFEL and ERL are advanced （or, say, 4th generation） light sources, with different electron beam parameters and different advantages. However, the linac used for XFEL and ERL should provide very advanced beams with high energy, high peak and/or average current, very low emittance and low energy spread, thus making the linac very complicated and expensive. To share the XFEL and ERL advantages and save the construction-operation budget, a proposal of using a common superconducting electron linac for hard X-ray XFEL and ERL is described in this paper. The interactions between the XFEL and ERL beams via the accelerating structure are studied and the result is positive.     

Towards one machine, two purposes: using a common SC linac for XFEL and ERL simultaneously

The linac based XFEL and ERL are advanced (or, say, 4th generation) light sources, with different electron beam parameters and different advantages. However, the linac used for XFEL and ERL should provide very advanced beams with high energy, high peak and/or average current, very low emittance and low energy spread, thus making the linac very complicated and expensive. To share the XFEL and ERL advantages and save the construction-operation budget, a proposal of using a common superconducting electron linac for hard X-ray XFEL and ERL is described in this paper. The interactions between the XFEL and ERL beams via the accelerating structure are studied and the result is positive.     

CRRFA-30L波段射频加速器

 主要介绍CRRFA-30L波段射频加速器结构和性能，论述了热阴极射频腔注入器、束流加速系统、微波功率源和控制等结构中主要技术及其研究进展，给出了加速器输出束流参数测量与测量结果分析，达到设计应用要求。     

ADS注入器II的5 MeV高能传输线的设计与搭建

ADS先导专项的注入器Ⅱ计划在将质子束通过一个Cryomodule加速到5 MeV后,进行10 mA连续束流的调试,以验证ADS低能段的强流超导直线加速器技术。为了将50 kW的束流功率沉积到束流垃圾站,需要搭建一条高能束流传输线,从超导段开始传输束流。采用两套三组合四极透镜控制束流包络及垃圾站的束流尺寸,利用诊断真空室进行水平和垂直发射度的测量。为避免束流产生的真空管道损伤,该传输线必须确保束流无损失地传输到垃圾站。A CW 10 mA,5 MeV beam commissioning of CADS Injector Ⅱ is planed recently to test the high power superconduction linac techniques.To transport 50 kW beam from linac to the beam dump,a high energy beam line (HEBT) line is designed and setup.Two Triplet are used to control the beam size along HEBT and at the beam dump.One diagnostics box is used for horizontal and vertical emittance measurement.To avoid damages to the vacuum pipe,beam should be transported to the beam dump without losses.The details of the HEBT design will be described in the paper.     

Progress of the Injector Linac Upgrade for the BEPCⅡ Project

BEPCⅡ—an upgrade project of Beijing Electron Positron Collider (BEPC) is a factory type of e+e- collider. It requires its injector linac to have a higher beam energy (1.89 GeV) for on-energy injection and a higher beam current (40 mA e+ beam) for a higher injection rate ( 50 mA/min). The low beam emittance (1.6π mm·mrad for e+ beam, and 0.2πmm·mrad for 300 mA e- beam) and the low beam energy spread (±0.5%) are also required to meet the storage ring acceptance. Thus the original BEPC injector linac must be upgraded to have a new electron gun with its complete tuning system, a new positron source with a flux concentrator, a new RF power system with its phasing loops and a new beam tuning system with orbit correction and optics tuning devices. These new components have been designed, fabricated, tested and will be installed in their final positions in this spring and summer, which are described in this paper.     

100 MeV电子直线加速器的物理设计

 能量为100 MeV左右的高性能电子直线加速器是第三代同步辐射光源注入器和自由电子激光注入器的重要组成部分,采用热阴极栅控电子枪、聚束系统和4根SLAC型加速管作为加速器主体结构,一套45 MW的速调管调制器系统和波导系统作为微波功率源系统。设计中,使用了国际通用的模拟软件对加速器的动力学特性进行了数值模拟和参数优化,电子束能量达到100 MeV以上,能散小于1%,归一化发射度小于30 mm·mrad。     

Wakefield Effects on the BEPCII Injector Linac

The high current and short bunch of the electron beam in the BEPCII injector linac cause the wakefield effects on the beam performance dilution. These wakefield effects on longitudinal and transverse beam dynamics are systematically studied with analysis and numerical beam modeling, including the single bunch short-range wake effects and the multi-bunch long-range wake effects on beam energy, energy spread, emittance, orbit offset and primary electron beam spot size on the positron production target. The measures to effectively cure these wake effects are also studied.