Facile fabrication of highly flexible,porous PEDOT: PSS/SWCNTs films for thermoelectric applications

High-performance organic composite thermoelectric(TE)materials are considered as a promising alternative for harvesting heat energy.Herein,composite films of poly(3,4-ethyienedioxythiophene):poly(styrene sulfonate)/single-walled carbon nanotubes(PEDOT:PSS/SWCNTs)were fabricated by utilizing a convenient solution mixing method.Thereafter,the as-prepared hybrid films were treated using sulfuric acid(H₂SO₄)to further optimize the TE performance.Film morphological studies revealed that the sulfuric acid treated PEDOT:PSS/SWCNTs composite samples all possessed porous structures.Due to the successful fabrication of highly conductive networks,the porous nano-architecture also exhibited much more excellent TE properties when compared with the dense structure of the pristine samples.For the post-treated sample,a high power factor of 156.43μW·m^-1·K^-2can be achieved by adjusting the content of CNTs,which is approximately 3 orders of magnitude higher than that of the corresponding untreated samples(0.23μW·m^-1·K^-2).Besides,the obtained films also showed excellent mechanical flexibility,owing to the porous nanostructure and the strong p–p interactions between the two components.This work indicates that the H₂SO₄ treatment could be a promising strategy for fabricating highly-flexible and porous PEDOT:PSS/SWCNTs films with high TE performances.     

旋涂法酸处理PEDOT∶PSS薄膜对OLED性能的影响

采用旋涂法对PEDOT∶PSS薄膜进行了酸处理,研究了不同方法处理PEDOT∶PSS薄膜对器件ITO/酸处理PEDOT∶PSS/NPB/Alq3/Li F/Al性能的影响。实验结果表明:用盐酸(草酸)处理PEDOT∶PSS薄膜时,以0.75 mol/L的盐酸(草酸)在120℃下退火15 min时性能更好,最大电流效率达到4.28 cd/A。并且盐酸、草酸处理PEDOT∶PSS薄膜制备器件比未处理PEDOT∶PSS薄膜制备器件的电流效率明显提高了34%。     

Modulating the Electrochromic Performances of Transmissive and Reflective Devices Using N,N-Dimethyl Formamide Modified Poly(3,4-Ethylenedioxythiophene)/Poly(Styrene Sulfonate) Blend as Active Layers

As one of the important factors which affect the properties and applications of conducting polymers, the electrical conductivity of a poly(3,4-ethylenedoxy-thiophene)/ poly(styrene sulfonate) (PEDOT: PSS) blend was adjusted by using various amount of an organic solvent (N,N-dimethyl formamide, DMF) as an additive. The conductivities of PEDOT: PSS thin films can be increased dramatically, from 1.0 S to 32.1 S cm^?1, with a 2/1 volume ratio of PEDOT: PSS/DMF loading after totally removing the organic solvent by annealing the film at 80° for 48 h in a vacuum oven. The optical contrasts of transmissive and reflective devices assembled using DMF-modified PEDOT: PSS as active layers exhibited a close relationship with the conductivity of PEDOT: PSS. Interestingly, high conductivity of PEDOT: PSS enhanced the contrast of a transmissive device, while high conductivity of PEDOT: PSS decreased the contrasts of a reflective device. The underlying reason is related to the different electrochromic mechanisms of these two types of device configurations.     

基于石墨烯/PEDOT：PSS叠层薄膜的柔性OLED器件

石墨烯具有独特的电学性能、优异的机械延展性和良好的化学稳定性,是制备高性能导电薄膜的理想材料,但是当前石墨烯的高电阻率限制了它的实际应用。本文采用喷涂方法制备了石墨烯/聚（3,4-亚乙二氧基噻吩）-聚（苯乙烯磺酸）（PEDOT：PSS）复合导电薄膜,对复合薄膜的表面形貌与光电性能进行了研究。PEDOT：PSS的引入不仅降低了石墨烯薄膜的表面电阻,同时还平滑了薄膜表面。在此基础上,成功制备了柔性黄光有机电致发光器件,器件在12 V时达到效率最大值0.9 cd/A。器件在曲率半径为10 mm时弯曲了100次后,发光亮度并无明显变化。该复合薄膜可实际应用于柔性有机电致发光显示器件。     

退火温度对电子束蒸发沉积Cu_2O薄膜性能的影响

近年来,钙钛矿太阳电池(PSCs)得到了迅猛发展,而无机空穴传输材料(IHTMs)的使用可进一步降低电池的成本,提高电池的稳定性.本文通过电子束蒸发制备了Cu_2O薄膜,研究了空气中退火温度及时间对薄膜组成、结构及光电性能的影响,并构筑了p-i-n反型平面异质结钙钛矿太阳电池.研究发现:由于热解作用,直接通过电子束蒸发制备的薄膜为Cu_2O和Cu的混合物;而在空气中经过退火后,由于氧化作用,随着退火温度的升高,薄膜的组分由混合物转变为纯的Cu_2O,再转变成纯的CuO.通过控制退火温度制备的Cu_2O薄膜的光学带隙约为2.5 eV,载流子迁移率约为30 cm~2·V~(-1)·s~(-1).应用于PSCs,薄膜的最佳厚度为40 nm,但电池性能低于PEDOT:PSS基的PSCs.这主要是由于钙钛矿前驱液在Cu_2O薄膜的润湿性较差,吸收层中有大量微孔洞存在,致使漏电流增强,电池的性能降低.然而,当采用Cu_2O/PEDOT:PSS双HTMs设计时,由于PEDOT:PSS对Cu_2O具有较强的腐蚀作用,使电池性能恶化.     

Thermoelectric Performance of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate)

Thermoelectric (TE) performances are systematically investigated for the pellets of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) with different organic additives and heating process as organic TE materials. The electrical conductivity, Seebeck coefficient and thermal conductivity versus temperature are determined, respectively. It is found that there is no distinct change for the Seebeck coefficient among each sample with the additions of dimethyl sulfoxide and ethylene glycol. The thermal conductivity measured in a wide range of temperature indicates that the PEDOT:PSS pellet have an extremely low value. The highest figure of merit (Z_T= 1.75×10^-3) is observed at 270K among the PEDOT:PSS pellets.     

Enhanced functionalities of DNA thin films by facile conjugation with conducting polymers

In this study, we discuss a method to embed PEDOT:PSS into DNA with a designated concentration of PEDOT:PSS and construction of PEDOT:PSS-embedded DNA thin films. In order to shed light on the interaction between PEDOT:PSS and DNA, optical spectroscopy measurements were performed. DNA-PEDOT:PSS thin films showed a broad absorption band around 800 nm which was associated with PEDOT:PSS. The electrical properties of DNA-PEDOT:PSS thin films were assessed. A significant enhancement in current for DNA-PEDOT:PSS thin films DNA was observed which agreed with the decrement in band gap of DNA-PEDOT:PSS thin films. For the energy storage capability and dielectric constant of DNA-PEDOT:PSS thin films, capacitance measurements were conducted. Frequency-dependent capacitance indicated enhancement in the capacitance and dielectric constant by electric polarization of PEDOT:PSS in a DNA thin film. Our approach may assist in development of various biosensors and electronic devices with specific functionalities based on biomaterials and conducting polymer complexes.     

Metal-electrode-free inverted organic photovoltaics using electrospray-deposited PEDOT:PSS and spin-coated HAT-CN exciton blocking layer

Poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) films were fabricated using an electrospray deposition (ESD) method. The ESD PEDOT:PSS films exhibited higher PSS content on the surface than spin-coated PEDOT:PSS films, which results in a higher work function. Based on this result, metal-electrode-free inverted organic photovoltaics (OPVs) were fabricated. The ESD PEDOT:PSS was used as the top electrode on the poly(3-hexythiophene-2,5-diyl) (P3HT):[6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) light-absorbing layer. The power conversion efficiency (PCE) of OPVs was significantly increased with the 1,4,5,8,9,11-hexaazatriphenylene hexacarbonitrile layer. The improved PCE would be attributed to the suppression of exciton quenching at the P3HT:PCBM and PEDOT:PSS interface.     

In-situ characterization of electrochromism based on ITO/PEDOT:PSS towards preparation of high performance device

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) is usually sandwiched between indium tin oxide(ITO) and a functional polymer in order to improve the performance of the device. However, because of the strong acidic nature of PEDOT:PSS, the instability of the ITO/PEDOT:PSS interface is also observed. The mechanism of degradation of the device remains is unclear and needs to be further studied. In this article, we investigate the in-situ electrochromism of PEDOT:PSS to disclose the cause of the degradation. X-ray photoelectron spectroscopy(XPS) was used to characterize the PEDOT:PSS films, as well as the PEDOT:PSS plus polyethylene glycol(PEG) films with and without indium ions. The electrochromic devices(ECD) based on PEDOT:PSS and PEG with and without indium ions are carried out by in-situ micro-Raman and laser reflective measurement(LRM). For comparison, ECD based on PEDOT:PSS and PEG films with LiCl, KCl, NaCl or InCl_3 are also investigated by LRM. The results show that PEDOT:PSS is further reduced when negatively biased, and oxidized when positively biased. This could identify that PEDOT:PSS with indium ions from PEDOT:PSS etching ITO will lose dopants when negatively biased. The LRM shows that the device with indium ions has a stronger effect on the reduction property of PEDOT:PSS-PEG film than the device without indium ions. The contrast of the former device is 44%, that of the latter device is about 3%. The LRM also shows that the contrasts of the device based on PEDOT:PSS+PEG with LiCl, KCl, NaCl, InCl_3 are 30%, 27%, 15%, and 18%, respectively.     

稀释溶剂对PEDOT：PSS薄膜和有机太阳能电池性能的影响

采用喷涂技术制备聚3,4-乙撑二氧噻吩：聚苯乙烯磺酸盐（PEDOT：PSS）有机层薄膜,系统研究了乙醇、去离子水、甲醇、异丙醇和乙二醇等稀释溶剂对PEDOT：PSS薄膜形貌、透过率及导电性能的影响。将PEDOT：PSS薄膜应用于有机太阳能电池器件的制备,研究了不同溶剂对器件性能的影响。实验结果表明：采用乙醇稀释PEDOT：PSS溶液,能有效抑制PEDOT：PSS颗粒团聚,降低薄膜粗糙度,提高薄膜的透过率和导电性。以其制备的太阳能电池器件的能量转换效率明显高于其他溶剂稀释,转换效率为2.66%。     

Poly (3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) Zr(IV) phosphate composite cation exchanger : sol-gel synthesis and physicochemical characterization

An organic-inorganic composite cation exchanger poly (3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) Zr(IV) phosphate was prepared by the sol-gel method for removal of cadmium, a toxic heavy metal pollutant causing adverse effects on human health. The synthesized material was characterized by various techniques such as thermo gravimetric analysis/differential thermal analysis/differential thermo gravimetry (TGA/DTA/DTG), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), and Fourier transform infrared spectroscopy (FT-IR). Organic polymer PEDOT:PSS binds with the inorganic counterpart and prevents the leaching of the inorganic parts, hence PEDOT:PSS Zr(IV) phosphate composite cation exchanger has improved ion exchange capacity than inorganic ion exchanger. The composite cation exchanger was found selective towards Cd(II) ions. The nature and composition of contacting solvents influence the selectivity of composite cation exchanger. The composite cation exchanger may be used for the removal of cadmium a toxic heavy metal ion.     

Structural,morphological and optical properties of PEDOT:PSS/QDs nano-composite films prepared by spin-casting

This paper describes the structural, morphological and optical properties of the nano-composite of poly (3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) and quantum dots (QDs). The ZnSe and CdSe QDs have been synthesized, with the aid of Mercaptoacetic acid (MAA), by a colloidal method with an average size of ~5 to 7 nm. QDs have been embedded in PEDOT:PSS using a simple solution processing approach and has been deposited as thin films by spin coating technique. The QDs embedded PEDOT:PSS enhances the light absorption spectra of samples, prominently in terms of absorption intensity which may consequently improve sensitivity of the optoelectronic devices.     

Effect of dimethyl sulfoxide on the electrical properties of PEDOT:PSS/n-Si heterojunction diodes

Effect of dimethyl sulfoxide (DMSO) on the electrical properties of PEDOT:PSS/n-Si heterojunction diodes has been studied. Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) was deposited on n-type Si wafer using facile process of spin coating. The DMSO content was varied from 0 to 8 vol%. Electrical characterization of these heterojunction diodes as performed using both current–voltage (I–V) and capacitance–voltage (C–V) measurements. All diodes showed rectifying behavior. AFM measurement revealed that the surface became more rough after the DMSO treatment of PEDOT:PSS films. The RMS values were found in the range of 4–6 nm. The resistivity of the PEDOT:PSS films decreased with increase in temperature. The addition of DMSO into PEDOT:PSS solution results in a decrease in resistivity of films by approximately two orders of magnitude. PEDOT:PSS films showed high transmission more than 85% in the entire visible region. Raman spectroscopy indicated effect of the DMSO treatment on the chemical structure of PEDOT chains, suggesting a conformational change of PEDOT chain in the film. An optimal value of DMSO was obtained with 5 vol% content, and it showed the best PEDOT:PSS films properties and good quality heterojunction diodes characteristics with ideality factor of 2.4 and barrier height 0.80 eV.     

Improving efficiency of inverted perovskite solar cells via ethanolamine-doped PEDOT:PSS as hole transport layer

In order to fabricate high-performance inverted perovskite solar cells (PeSCs), an appropriate hole transport layer (HTL) is essential since it will affect the hole extraction at perovskite/HTL interface and determine the crystallization quality of the subsequent perovskite films. Herein, a facile and simple method is developed by adding ethanolamine (ETA) into poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as HTL. The doping of a low-concentration ETA can efficiently modify the electrical properties of the PEDOT:PSS film and lower the highest occupied molecular orbital (HOMO) level, which is more suitable for the hole extraction from the perovskite to HTL. Besides, ETA-doped PEDOT:PSS will create a perovskite film with larger grain size and higher crystallinity. Hence, the results show that the open-circuit voltage of the device increases from 0.99 V to 1.06 V, and the corresponding power conversion efficiency (PCE) increases from 14.68% to 19.16%. The alkaline nature of ethanolamine greatly neutralizes the acidity of PEDOT:PSS, and plays a role in protecting the anode, leading the stability of the devices to be improved significantly. After being stored for 2000 h, the PCE of ETA-doped PEDOT:PSS devices can maintain 84.2% of the initial value, which is much higher than 67.1% of undoped devices.     

PEDOT:PSS Schottky contacts on annealed ZnO films

Polycrystalline ZnO and ITO films on SiO₂ substrates are prepared by radio frequency (RF) reactive magnetron sputtering. Schottky contacts are fabricated on ZnO films by spin coating with a high conducting polymer, poly(3, 4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) as the metal electrodes. The current-voltage measurements for samples on unannealed ZnO films exhibit rectifying behaviours with a barrier height of 0.72 eV (n=1.93). The current for the sample is improved by two orders of magnitude at 1 V after annealing ZnO film at 850 ℃, whose barrier height is 0.75 eV with an ideality factor of 1.12. X-ray diffraction, atomic force microscopy and scanning electron microscopy are used to study the properties of the PEDOT:PSS/ZnO/ITO/SiO₂. The results are useful for applications such as metal-semiconductor field-effect transistors and UV photodetectors.     

Effect of sorbitol doping in PEDOT:PSS on the electrical performance of organic photovoltaic devices

Organic photovoltaic cells have important advantages, such as low cost and mechanical flexibility. The conducting polymer poly(3,4 ethylenedioxy-thiophene):poly(styrene sulfonate) (PEDOT:PSS) has been widely used as an interfacial layer or a polymer electrode in polymer electronic devices, such as photovoltaic devices and light-emitting diodes. In this report, we discuss the direct current (DC) conductivity of PEDOT:PSS films containing various weight ratios of sorbitol dopant. The work function is shown to steadily decrease with increasing dopant content. With different dopant contents, illuminated current–voltage photovoltaic characteristics were observed. Ultraviolet photoelectron spectroscopy (UPS) analysis revealed that the work function of the PEDOT:PSS was affected by its sorbitol content. The morphologies of the doped PEDOT:PSS films were characterized by atomic force microscopy (AFM). For the device fabrication, we made organic photovoltaic cells by a spin-coating process and Al deposition by thermal evaporation. The sorbitol dopant is able to improve the efficiency of the device.     

Optical and electroluminescent properties of a number of new derivatives of divinyl dibenzothiophene sulfone

Photoluminescent and electroluminescent properties of four new bipolar linear derivatives of divinyl dibenzothiophene sulfone are studied. It is found that amorphous films of solutions, as well as films of the compounds under study in the poly(N-vinylcarbazole) matrix, have a rather high quantum yield of photoluminescence in the blue and blue-green spectrum regions. Bright blue electroluminescence is obtained in the samples with a structure of ITO/PEDOT:PSS/TPD/OC/LiF/Al using vacuum deposition of the compounds under study and in the single-layer ITO/PEDOT:PSS/PVK:OC/LiF/Al structure when applied from the solution with a threshold voltage of 2.5–3.5 V. The influence of a molecule structure on the spectra and quantum yield of fluorescence as well as on the electroluminescent properties of the compounds is shown. Results of quantum-chemical calculations in the context of the density functional theory of the structure and characteristics of main molecular orbitals are presented.     

Properties of conductive polymer films deposited by infrared laser ablation

Thin films of the conducting polymer poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) were deposited by resonant infrared laser vapor deposition (RIR-LVD). The PEDOT:PSS was frozen in various matrix solutions and deposited using a tunable, mid-infrared free-electron laser (FEL). The films so produced exhibited morphologies and conductivities that were highly dependent on the solvent matrix and laser irradiation wavelength used. When deposited from a native solution (1.3% by weight in water), as in matrix-assisted pulsed laser evaporation (MAPLE), films were rough and electrically insulating. When the matrix included other organic “co-matrices” that were doped into the solution prior to freezing, however, the resulting films were smooth and exhibited good electrical conductivity (0.2 S/cm), but only when irradiated at certain wavelengths. These results highlight the importance of the matrix/solute and matrix/laser interactions in the ablation process.     

Enhanced thermoelectric properties of PEDOT/PSS/Te composite films treated with H<Subscript>2</Subscript>SO<Subscript>4</Subscript>

Firstly, tellurium (Te) nanorods with a high Seebeck coefficient have been integrated into a conducting polymer PEDOT/PSS to form PEDOT/PSS/Te composite films. The Seebeck coefficient of the PEDOT/PSS/Te (90 wt.%) composite films is ~191 μV/K, which is about 13 times greater than that of pristine PEDOT/PSS. Then, H₂SO₄ treatment has been used to further tune the thermoelectric properties of the composite films by adjusting the doping level and increasing the carrier concentration. After the acid treatment, the electrical conductivity of the composite films has increased from 0.22 to 1613 S/cm due to the removal of insulating PSS and the structural rearrangement of PEDOT. An optimized power factor of 42.1 μW/mK² has been obtained at room temperature for a PEDOT/PSS/Te (80 wt.%) sample, which is about ten times larger than that of the untreated PEDOT/PSS/Te composite film.     

Conductivity of Composite Films Based on Conductive Polymer PEDOT:PSS,Graphene Oxide and Nanoparticles TiO2 for Contact Layers of Perovskite Photovoltaic Structures

Physics of the Solid State - The electrical properties of composite films based on conductive polymer PEDOT: PSS, graphene oxide (GO), and titanium dioxide nanoparticles (TiO2) (PEDOT: PSS–...