Design of a polarization splitter for an ultra-broadband dual-core photonic crystal fiber

A novel ultra-broadband polarization splitter based on a dual-core photonic crystal fiber (DC-PCF) is designed. The full-vector finite element method and coupled-mode theory are employed to investigate the characteristics of the polarization splitter. According to the numerical results, a graphene-filled layer not only broadens the working bandwidth but also reduces the size of the polarization splitter. Furthermore, the fluorine-doped region and the germanium-doped region can broaden the bandwidth. Also, the 4.78 mm long polarization splitter can achieve an extinction ratio of -98.6 dB at a wavelength of 1550 nm. When extinction ratio is less than -20 dB, the range of the wavelength is 1027 nm-1723 nm with a bandwidth of 696 nm. Overall, the polarization splitter can be applied to all-optical network communication systems in the infrared and near-infrared wavelength range.     

高衍射效率衍射望远镜系统的设计/加工及成像性能测试

为提高衍射效率,设计并制作了口径为300mm的衍射成像系统.该系统的物镜是由一块四台阶位相型菲涅尔波带片通过激光直写套刻和Ar离子束物理刻蚀技术在石英玻璃基板上加工而成.测试了衍射物镜的衍射效率,实验结果表明:衍射物镜在波长632.8nm处的衍射效率为66.4%,达到理论值的82%.搭建了衍射成像系统光路,分别采用10μm星点孔与分辨率板,测试了系统的成像性能.实验测得星点像直径为44μm,分辨率板的极限分辨率达到84lp/mm,接近该系统的理论计算值,表明该衍射成像系统具有较好的成像性能.     

Planar waveguide-coupled, high-index-contrast, high-Q resonators in chalcogenide glass for sensing

High-index-contrast compact microdisk resonators in thermally evaporated As2S3 and Ge17Sb12S71 chalcogenide glass films are designed and fabricated using standard UV lithography and characterized. Our pulley coupler configuration demonstrates coupling of the resonators to monolithically integrated photonic wire waveguides without resorting to demanding fine-line lithography. Microdisk resonators in As2S3 support whispering-gallery-mode with cavity quality factors (Q) exceeding 2 x 10(5), the highest Q value reported in resonator structures in chalcogenide glasses to the best of our knowledge. We have successfully demonstrated a lab-on-a-chip prototype sensor device with the integration of our resonator with planar microfluidic systems. The sensor shows a refractive index sensitivity of 182 nm/RIU (refractive index unit) and a wavelength resolution of 0.1 pm through a resonant peak fit. This corresponds to a refractive index detection limit of 8 x 10(-7) RIU at 1550 nm in wavelength, which could be further improved by shifting the operating wavelength to a region where water absorption is reduced.     

近红外波段硅基金属光子晶体平板的亚波长成像特性

利用时域有限差分方法,理论上研究了由正方形金属嵌入背景材料硅中组成的二维正方晶格和三角晶格光子晶体的亚波长成像特性。采用Drude模型描述金属银的色散特性,在近红外波段该模型可以很好地描述金属的实际介电常数。通过结构参数的设计,在上述两种结构中实现了波长在1550nm附近的亚波长成像,并且发现金属对入射光的吸收使得成像位置处的光强稍有降低,但是对于光子晶体亚波长成像的质量并无影响。相对于通常的硅基空气孔型光子晶体亚波长成像器件,该种硅基金属型全固态光子晶体结构更加稳定,因而可以更好地在复杂全光集成回路中加以实际应用。     

含氟聚酰亚胺波导波长分离耦合器优化设计

提出并采用统计优化的设计方法解决含氟聚酰亚胺波导波长交叉分离耦合器的偏振态变动的影响.在实测了含氟聚酰亚胺的色散和双折射特性的基础上,优化设计了40路波长信道、1550 nm中心波长、0.8 nm波长间隔的抗偏振变动的波长交叉分离耦合器.数值模拟显示:波长周期偏移小于0.1 nm,1 dB带宽为0.5 nm,3 dB带宽为0.8 nm,串扰小于－30 dB,偏振变动导致的波长漂移小于0.08 nm.     

双泵浦光子晶体光纤参量放大研究

利用光子晶体光纤在不同零色散波长附近具有不同色散的特性，研究了在零色散波长为780 nm和1550 nm附近的双泵浦光子晶体光纤参量放大过程.在780 nm附近，讨论了零色散波长变化对双泵浦光子晶体光纤参量放大的影响.数值模拟结果表明:当零色散波长发生微小的变化时，信号增益谱带宽会发生很大的变化.当两泵浦光之间的波长差值减小时，零色散波长的变化对参量放大的影响在很大程度上可以得到抑制，但是增益带宽会有一定的减小.依据这一原理，在1550 nm附近设计光子晶体光纤中的色散平坦光纤参量放大，在5 m长的光子晶体光纤中，当峰值功率为10 W时，得到了增益为65 dB，带宽达到420 nm且极为平坦的增益谱.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

Ultra-violet and mid-infrared continuum generation by cross-phase modulation between red-shifted solitons and blue-shifted dispersive waves in a photonic crystal fiber

Using a photonic crystal fiber with a zero dispersion wavelength of the fundamental mode at 780 nm designed and fabricated in our lab, the ultraviolet and mid-infrared continua are generated by cross-phase modulation between red-shift solitons and blue-shift dispersive waves. The dependences of continuum on the pump power and wavelength are investigated. With the pump working at 820 nm, when the pump power increases from 300 to 500 mW, the bandwidths of ultraviolet and mid-infrared continua change from 80 to 140 nm and 100 to 200 nm, respectively. The wavelength of ultraviolet continuum is below 246 nm, and the wavelength of mid-infrared continuum exceeds 2500 nm. Moreover, the influences of pump power on wavelength and conversion efficiency of different parts of continua are also demonstrated.     

InGaAsP/InP DH Ridge Waveguide Phase Modulator with High Modulation Efficiency

The P-p-n-N InGaAsP/InP ridge waveguide phase modulator has been fabricated and investigated at a wavelength of 1550nm. The phase modulation efficiency measured by the Fabry-Perot resonance method is as high as 34°/V.mm for TE mode. The QEO effect becomes dominant from -4V to -8V.     

大容量长距离传输用低非线性效应非零色散位移光纤

利用非等温等离子体化学气相沉积 (PCVD)工艺制备了一种适合于大容量高速率长途干线网与城域网的中芯下陷型纤芯结构非零色散位移光纤。该光纤的有效面积大于 95 μm2 ,在 15 5 0nm波段的色散值约为9ps/(nm·km) ,有效的抑制了传输过程中光非线性效应的产生。通过对光纤剖面结构的优化设计 ,光纤的 15 5 0nm处的传输损耗降到约 0 .2 1dB/km ,与传统单模光纤的熔接损耗低于 0 .11dB ,且在直径为 6 0mm圆筒上绕 10 0圈后在 14 6 0nm到 16 2 5nm波长范围所引起的附加弯曲损耗均低于 0 .0 2dB/km。同时 ,该光纤色散斜率低于0 .0 6 5 ps/(nm2 ·km) ,偏振模色散 (PMD)小于 0 .0 5 ps·km-1/2 。此外 ,由于光纤的零色散点移到了 14 30nm以下 ,使波分复用 (WDM)传输在S波段 (14 6 0～ 15 30nm)、C波段 (15 30～ 15 6 5nm)、L(15 6 5～ 16 2 5nm)波段上都兼容。     

Integrated photonic crystal spectrometers for sensing applications

A combination of negative refraction and diffraction compensation in a superprism-based photonic crystal structure is used to demonstrate a compact on-chip photonic crystal spectrometer. This structure provides strong dispersion and signal isolation, which are essential for forming an efficient and compact spectrometer. Performance of these spectrometers as spectral pattern detectors is discussed. The experimental results show that a PC structure with 80 μm × 220 μm dimension can locate a single spectral feature with better than 10 pm accuracy over a bandwidth of 50 nm around 1550 nm center wavelength at an output signal-to-noise ratio of 13 dB.     

激光告警中近红外焦平面阵列探测器成像技术研究

为了提高激光探测的方位分辨率,实现对来袭激光的准确定位,选用了FPA-320x256-C型InGaAs焦平面阵列探测器作为光栅衍射型激光告警装置的核心元件。介绍了基于光栅衍射的激光波长和方向探测原理,在分析了探测器性能及参数的基础上设计了驱动电路。探测器在FPGA时序的控制下,输出模拟量通过高速AD进行采集,数据经缓存后存储在FPGA外扩的SRAM中,然后通过USB传送至PC机。上位机Labview采集原始数据,处理并显示。利用上述方法,完成了成像实验,采用波长为1 550和980 nm的激光器从不同角度进行入射,对探测得到的衍射图像进行分析,判断出零级和一级的位置,根据光栅衍射理论,计算出相应波长和二维方向入射角,结果显示波长误差小于10 nm,入射角误差小于1°。     

棱镜-光栅-棱镜型光谱成像系统光学设计

为实现成像光谱仪系统的直视性和小型化特点,设计一种棱镜-光栅-棱镜（PGP）结合式元件,作为分光系统的成像光谱仪光学系统装置。系统主要包括PGP分光原件、准直系统、成像系统和接收系统。光栅采用体全息相位光栅,可以获得很高的衍射效率,准直和成像镜采用对称式结构,可以有效地消垂轴像差。根据实际指标探测器像元尺寸为20 m20 m,像元数为512512,采用双像元合并方法,光谱通道数为148个,狭缝大小为10.2 mm10.2 mm,波段在400 nm~800 nm,物方数值孔径为0.15。分析了PGP光谱成像系统的原理、特点,对参数关系和体全息相位型光栅的衍射效率进行了详细的讨论。分析结果表明:PGP元件在整个光谱范围内理论衍射效率大于0.6,采用ZEMAX软件进行优化设计,得到系统的平均光谱分辨率优于3 nm,在截止频率处平均传递数大于0.7,系统总长90 mm。     

跑道型结构光子晶体波导定向耦合器

鉴于波导定向耦合器在集成光路以及光电集成方面的广泛应用,提出了一种基于光子晶体波导间高效耦合的光子晶体定向耦合器。通过主波导和耦合波导间的耦合,可以实现对波长为1 490 nm和1 550 nm电磁波的高效分光。在将器件长度控制在30 μm左右的同时,其总效率高达93.05%。另外,发现主波导和耦合波导间介质柱结构参数对电磁波的耦合周期有着极大的影响。并通过将介质柱沿z方向拉伸0.1a(a为晶格周期),设计了工作波长为1 530 nm和1 540 nm的光子晶体定向耦合器,器件长度仅为60 μm。通过拉伸介质柱的纵向长度,可以大幅减小耦合周期,这对缩小器件体积以及实现更为密集的波分复用有着重要的意义。     

Double groove silicon grating polarizer in telecommunication wavelength band

In this paper, we propose an ultra broad band polarizer operating in the telecommunication wavelength band, this device consisting a double groove silicon grating is designed with using the inverse mathematical method and rigorous vector diffraction theory. It is shown from our calculations that the device presents extremely high reflection (R > 95%) for TE polarization light and high transmission (T > 95%) for TM polarization over ∼400 nm wavelength range, moreover, the extinction ratio is ∼30 in the central wavelength 1550 nm. Furthermore, it is found with rigorous coupled wave analysis (RCWA) that the extremely wide band property for TE polarization is due to the excitation of strong modulation guided modes in the design wavelength range.     

一种高通量宽带近红外声光可调滤光器的设计

声光可调滤光器(AOTF)是20世纪90年代以来近红外光谱仪最突出的进展,传统的单换能器结构使滤光器存在工作带宽较窄的问题。本文采用双换能器结构设计了一种高通量、宽带宽的近红外声光可调滤光器,基于“切面平行条件”波矢量布局方案,通过仿真计算确定声光晶体最优切向切角及换能器长度等最佳参数。两段换能器分别工作于两个不同的波段范围,使得滤光器的工作波段范围在光谱分辨率、衍射效率等参数满足要求的前提下大为改善。测试结果表明,设计的滤光器在900～2 400 nm波段范围内分辨率优于15 nm,衍射效率最高可到41%。     

外腔半导体激光器用恒流源电路设计与实现

由于外腔半导体激光器系统中的核心部分——激光器受外界环境影响较大，在装配或工作中极易受到电压、电流和静电荷的影响而损坏.为减少由于电路不稳定产生的激光器损坏，在借鉴各种传统的恒流源电路实现方式的基础上，运用反馈恒流原理，慢启动慢关闭原理，利用场效应管特性，给出一种高准确度恒流电路实现方式.将此电路直接运用于中心波长1550 nm激光器作为驱动电路，工作稳定、输出电流受负载影响很小且输出准确度达到同行业先进水平.电流稳定达到0.01％以上.此电路实现方式简单，实用性较强，对整个电路做出了实验仿真和测试，很好地解决了由于驱动电流不稳造成的激光器损坏的问题.     

Wide band polarizer with suspended silicon grating

In this paper, we propose an ultra broadband polarizer operating in the telecommunication wavelength band; this device consisting a single silicon suspended resonant grating layer is designed with using the inverse mathematical method and rigorous vector diffraction theory. It is shown from our calculations that the device presents extremely high reflection (R > 98%) for TE polarization light and high transmission (T > 98%) for TM polarization over ∼330 nm wavelength range; moreover, the extinction ratio is ∼100 in the central wavelength 1550 nm. Furthermore, it is found with Rigorous Coupled Wave Analysis (RCWA) and near field distribution that the extremely wide band property for TE polarization is due to the excitation of strong modulation guided modes in the design wavelength range.     

Channel drop filter using photonic crystal ring resonators for CWDM communication systems

In this paper, a new optical channel drop filter (CDF) using photonic crystal ring resonators (PCRRs) is presented. Using the two-dimensional (2D) finite-difference time-domain (FDTD) method in triangular lattice photonic crystal (PC) silicon rods, 100% forward dropping efficiency and a quality factor of more than 1000 can be achieved in third communication window while the resonant wavelength is 1550 nm. Through this novel (CDF), a multi-CDF operation with 100% drop efficiencies across all channels can be obtained. The proposed device could be used in future coarse wavelength division multiplexing (CWDM) communication systems.