一种调节反馈有源噪声控制系统水床效应的频域自适应算法*

伯德灵敏度积分决定反馈有源控制系统具有水床效应,即某个频段内的噪声衰减伴随着另一频段内的噪声放大。已有的反馈系统自适应算法没有明确考虑噪声放大量,非自适应算法考虑了噪声放大量但不能在线调整。为了使自适应反馈系统能明确调节噪声放大量,该文以控制器某个频段内的幅度响应小于指定阈值为约束条件,并作为"惩罚项"与误差信号能量相加得到代价函数,通过最速下降法最小化该代价函数得到了一种频域自适应算法。与已有算法在有源降噪耳机实例中的对比结果表明,该算法能够更为直接地对指定频段内的噪声放大量进行调节,从而在降噪量与噪声放大量之间取得折衷。     

充液管路系统流体声与结构声的复合有源控制

采用基于谐频自适应控制算法的有源消声与消振系统对充液管路系统突出的低频线谱噪声进行有源控制实验研究.建立了泵水循环管路实验系统,在管路中安装有源消声器对流体声进行控制,在管路出口障板上采用8×8通道有源消振系统控制结构声辐射。开展的低频线谱噪声与振动有源控制实验结果表明,在50~200 Hz频带内,通过结合有源噪声与振动控制可在多数频点取得10 dB以上的降噪效果。针对该实验系统,通过分别控制流体声和结构声分析了两者的贡献.实验结果验证了有源消声与消振系统具有较好的降噪性能,各频点处流体声与结构声占比情况不同,需要综合控制流体声与结构声才可以取得显著的降噪效果。      

有源声屏障中误差传感器的位置优化

有源声屏障利用有源控制系统提高声屏障低频段的降噪效果。有源控制系统中误差传感器的位置对整个系统的降噪效果有较大的影响。通过数值模拟和实验研究误差传感器的位置优化问题,得出了有源控制系统中误差传感器摆放位置的两条结论:(1)所介绍的三种摆放中,误差传感器的位置在次级声源的正上方时,有源控制系统在屏障后方声影区引入的新增插入损失最好,特别是对于距离屏障较远的区域;(2)当误差传感器的位置在次级声源的正上方时,误差传感器与次级声源间的距离存在一个最优距离使得屏障后方声影区的衍射声得到最好的降低。     

参量阵扬声器在管道噪声控制中的研究*

为了解决管道有源噪声控制中声反馈造成的系统复杂度和计算量的增加,文中引入参量阵扬声器作为次级声源,利用其强指向性减小控制系统的声反馈。为了验证该方法可行性,本文分别在直管和L管中,对600 Hz单频噪声和频率范围为500 Hz~1000 Hz的窄带噪声进行了管道有源噪声控制,同时测量了参量阵扬声器的管内声场和降噪范围。结果表明,参量阵扬声器声反馈小,在没有声反馈补偿的条件下对单频噪声的降噪效果基本达到了声反馈补偿条件下普通扬声器的降噪效果,对窄带噪声的降噪效果稍差。此外,通过测量管道声场和降噪量,确定了参量阵扬声器的降噪区域为误差传感器下游整个管道,降噪面积为管道整个截面。这说明参量阵扬声器作为次级声源降低了系统的复杂度和算法的计算量,并取得了较好的降噪效果。     

军用运输机机舱有源消声实验系统的设计与实现

为验证有源消声技术在军用运输机机舱低频噪声消除方面的有效性,设计和实现了一套机舱有源消声实验系统。采用“激振器+舱壁板”方式实现了飞机螺旋桨对机舱诱导噪声的声源模拟,设计了基于前馈控制结构的自适应有源噪声控制系统,构建了基于FX-LMS算法的自适应消声控制器,采用监测麦克风组对舱内空间的消声效果进行监测。实验结果验证了自适应有源噪声控制技术在军用飞机舱室消声降噪领域的有效性,并表明初、次级声源间距对自适应有源消声系统的消声效果具有重要的影响。     

次级声源优化布放的局部空间有源降噪

针对区域有源降噪问题,为获得更优降噪效果,根据实际次级通路传递函数,提出次级声源优化布放的有源控制系统并详细比较了两种次级声源优化布放算法与次级声源均匀布放的实际降噪效果。应用的第一种次级声源优化算法是l2范数约束的约束匹配追踪算法,第二种次级声源优化算法是l1范数约束的稀疏正则化方法。在全消声室中利用扬声器线阵进行多通道有源降噪实验研究,实验结果表明,在200~1000 Hz,次级声源优化布放的控制系统的平均降噪量比次级声源均匀布放的控制系统的平均降噪量多5 dB左右;在1100~1900 Hz,次级声源优化布放的控制系统的平均降噪量比次级声源均匀布放的控制系统的平均降噪量多11~13 dB左右,次级声源优化布放的控制系统的降噪量分布更加均匀且次级声源输出能量更小。此外,两种优化算法中,稀疏正则化方法的降噪效果更佳。     

管道有源消声器

有源消声器对于管道中低频噪声的抑制比较有效。本文介绍的由单指向性传声器、延时器、单指向性扬声器构成的有源消声器,对于单频声,在100—315Hz频率范围可降低35—55dB;对于1/3倍频程噪声,可降低14—24dB;对于宽频带噪声,在一个倍频程内可降低8—20dB。     

局部空间自适应宽带有源消声

本文提出一个局部空间自适应宽带有源消声系统,该系统能实现有源消声所要求的任意带宽噪声在局部空间衰减,能自动补偿背景噪声及消声装置中不可控参数及噪声源变化对消声效果的影响.自适应滤波由TMS 32010数字信号处理器采用NLMS算法多路并行处理完成.实验结果表明:对普通房间中的单次级源布置方式,在主次级源前方1m,±30°扇面区域内,该系统对20—600Hz内的宽带噪声抵消,取得的最大降噪量在25dB(A)以上.     

利用质量流注入的流激孔腔噪声共振峰抑制

通过数值仿真揭示了开口前缘垂直注入质量流和前壁面平行注入质量流抑制流激孔腔噪声的机制,研究了多参数影响下脉动压力峰值降噪量和总降噪量随质量流注入速度的变化规律。开口前缘垂直注入质量流通过抬升剪切层,避免漩涡冲击开口后缘,抑制流激孔腔噪声脉动压力峰值;在一定范围内质量流注入速度越大,脉动压力峰值降噪量越大,但是低频部分引起的抬升也会越高,导致总降噪量先增大后减小;经优化后的峰值降噪量和总降噪量分别可以达到15 dB和9.5 dB。开口前壁面平行注入质量流则是通过加强开口处剪切层的稳定性,避免发生漩涡脱落,达到抑制流激孔腔噪声的目的;当质量流入口面积大于孔腔开口前壁面积2/3时,不仅可以显著降低流激孔腔噪声脉动压力的峰值,并且可以很好地抑制其它频段噪声的抬升;质量流注入速度为来流速度的0.5倍时,脉动压力峰值降噪量和总降噪量分别可以达到18 dB和15.4 dB。     

次级源近场和管壁弹性对充液管路有源消声性能的影响EI北大核心CSCD

建立了含次级源结构的充液直管有源消声系统数值模型,重点分析了声激励下次级源近场和管壁弹性对有源消声性能的影响。结果表明:次级源近场为非均匀声场,误差点位于该区域时部分频点控制效果较差甚至放大,而处于声场均匀区域时可使降噪量提高10 dB以上,增加误差点数量可使绝大多数频点的降噪量提高5 dB以上;管壁弹性使次级源与管壁间的耦合较强,非对称分布的次级源容易激起管壁振动,导致降噪谷值的出现,采用对称分布的次级源可显著提升控制效果;增加次级源数量能够提高系统的有源无源复合控制效果,但使得管内声场变得复杂,多次级源模型的有源消声效果随频率升高而有所降低。     

GA-based optimization of a MIMO ANC system considering coupling of secondary sources in a telephone kiosk

In this paper a multi-input, multi-output (MIMO) active noise control system with the aim of global reduction of broadband noise in a telephone kiosk is addressed. The model selected for this optimization problem is the acoustic environment of an enclosure taking into account the effect of coupling of secondary sources used for control purpose. This optimization involves finding the best locations for loudspeakers and microphones inside the enclosure as well as optimizing the control signals considering secondary source coupling.Previous results show that in order to be able to reduce acoustic noise globally inside the enclosure, the frequency range of 50-300 Hz must be selected for control purpose. The mean of acoustic potential energy of the enclosure, when excited in this frequency range, is adopted as a performance measure. This performance index is penalized with the power of the signal required to excite secondary loudspeakers, in order to avoid placements that may need high voltage power amplifier for a desired performance. To find the solution of this problem, i.e. the global minimum of the performance index, several genetic algorithms are proposed and compared. In order to attain the best achievable performance in reaching the global minimum, the parameters of these genetic algorithms are tuned, and used for optimization purpose. Numerical simulations of the acoustical potential energy as well as the sound pressure at different heights of the kiosk, when active noise control (ANC) system operates, confirm the optimality of the locations proposed by the genetic algorithm.     

Active control of the volume acquisition noise in functional magnetic resonance imaging: method and psychoacoustical evaluation.

Functional magnetic resonance imaging (fMRI) provides a noninvasive tool for observing correlates of neural activity in the brain while a subject listens to sound. However, intense acoustic noise is generated in the process of capturing MR images. This noise stimulates the auditory nervous system, limiting the dynamic range available for displaying stimulus-driven activity. The noise is potentially damaging to hearing and is distracting for the subject. In an active noise control (ANC) system, a reference sample of a noise is processed to form a sound which adds destructively with the noise at the listener's ear. We describe an implementation of ANC in the electromagnetically hostile and physically compact MRI scanning environment. First, a prototype system was evaluated psychoacoustically in the laboratory, using the electrical drive to a noise-generating loudspeaker as the reference. This system produced 10-20 dB of subjective noise-reduction between 250 Hz and 1 kHz, and smaller amounts at higher frequencies. The system was modified to operate in a real MR scanner where the reference was obtained by recording the acoustic scanner noise. Objective reduction by 30-40 dB of the most intense component in scanner noises was realized between 500 Hz and 3500 Hz, and subjective reduction of 12 dB and 5 dB in tests at frequencies of 600 Hz and at 1.9 kHz, respectively. Although the benefit of ANC is limited by transmission paths to the cochlea other than air-conduction routes from the auditory meatus, ANC achieves worthwhile attenuation even in the frequency range of maximum bone conduction (1.5-2 kHz). ANC should, therefore, be generally useful during auditory fMRI.     

Experimental results for multichannel feedforward ANC with noninvasive system identification

This paper presents experimental validation of a class of algorithms designed to enable active noise control (ANC) to function in environments when transfer functions change significantly over time. The experimental results presented are for broadband, local quieting in a diffuse field using a multichannel ANC system. The reverberant enclosure is an ordinary room, measuring approximately 1.4 x 2.4 x 2.4 m3 and containing a seated occupant, with six microphones defining the quiet zone near the occupant's ears. The control system uses a single reference signal and two error channels to drive four secondary sources. Using an ideal reference sensor, reduction in sound pressure level is obtained at the quiet-zone microphones averaged over the frequency range 50 to 1000 Hz with an occupant seated in the room. Two main results are presented: first for an adaptive cancelling algorithm that uses static system models, and second for the same algorithm joined with a noninvasive real-time system identification algorithm. In the first case better than 23 dB of performance is obtained if the occupant remains still through calibration and testing. In the second case, approximately 18 dB is obtained at the error microphones regardless of the motion of the occupant.     

Shielding against noise interfering with quantitation of insect infestations by acoustic detection systems in grain elevators

Acoustic devices used to detect hidden insect infestations must be shielded from noise in most practical applications. One device developed specifically for use in a noisy environment, the Acoustic Location ‘Fingerprinting’ Insect Detector (ALFID), counts the numbers of insects present in grain samples from shipments being graded for export at commercial grain elevators. This report considers the performance of ALFID's noise-shielding components, which include an enclosure for passive reduction of ambient noise, and an electronic system for active detection and masking of sounds originating outside the grain sample container. Sound pressure levels (SPLs) of ambient noise are reduced inside the enclosure by 60–90 dB at frequencies between 1 and 10 kHz, with a reduction of ~6.5 dB per octave (frequency doubling). The active noise-masking system protects ALFID from loud ambient sounds not sufficiently attenuated by the enclosure. If the output from one of four sensors mounted on the outside of the grain sample container rises above a preset amplitude threshold, a signal is triggered that inhibits acquisition of insect sound data from sensors inside the container. In tests of the complete ALFID system at a grain elevator with ambient noise of 73 ± W dB re 20 μPa SPL, the mean rate of noise-mask triggering was 5.5 s⁻¹, inhibiting acquisition of insect sounds for only 3.9% of the total testing period. This level of performance is sufficient to enable successful operation of ALFID under such noise conditions.     

A relaxed condition for "perfect" cancellation of broadband noise in 3D enclosures

This paper presents a relaxed condition for "perfect" cancellation of broadband noise in 3D enclosures. On the basis of a truncated modal model, it can be shown that the primary and secondary paths belong to a same subspace if a certain condition is satisfied. There exists a finite impulse response (FIR) filter transfer function vector for perfect cancellation of the primary paths. The analytical result is verified numerically with an active noise control (ANC) system in a 3D rectangular enclosure. The proposed ANC scheme is shown to fit well into the framework of an existing multichannel least-mean squares (LMS) algorithm for adaptive implementation.     

基于脉冲声分离的刚性球散射声控制

提出了一种基于脉冲声的三维空间中刚性球散射声分离方法,并利用前馈、固定系数控制方式对分离出的散射声进行有源控制,抑制散射声强度,实现了刚性球散射体在观测点处“声学不可见”。该方法利用脉冲信号作为初级噪声,通过有无刚性球时传声器采集脉冲信号的差值确定散射声大小,实现散射声与声源直达声的分离。对分离出的散射声进行多通道有源控制以验证该文所提分离方法及控制系统的有效性。实验结果表明,700~1000 Hz范围内,有源控制开启后,双通道散射声的平均降噪量大于5 dB,多通道散射声的平均降噪量大于8 dB,且误差传声器处采集的残余声场与无刚性球时采集的初级声场信号波形基本一致,实现了刚性球散射体在误差传声器处“声学不可见”。此外,参考传声器布放位置的选取问题也在该文做了详细讨论。     

Robust active noise control in the loadmaster area of a military transport aircraft

The active noise control (ANC) method is based on the superposition of a disturbance noise field with a second anti-noise field using loudspeakers and error microphones. This method can be used to reduce the noise level inside the cabin of a propeller aircraft. However, during the design process of the ANC system, extensive measurements of transfer functions are necessary to optimize the loudspeaker and microphone positions. Sometimes, the transducer positions have to be tailored according to the optimization results to achieve a sufficient noise reduction. The purpose of this paper is to introduce a controller design method for such narrow band ANC systems. The method can be seen as an extension of common transducer placement optimization procedures. In the presented method, individual weighting parameters for the loudspeakers and microphones are used. With this procedure, the tailoring of the transducer positions is replaced by adjustment of controller parameters. Moreover, the ANC system will be robust because of the fact that the uncertainties are considered during the optimization of the controller parameters. The paper describes the necessary theoretic background for the method and demonstrates the efficiency in an acoustical mock-up of a military transport aircraft.     

Noise reduction in a mode-locked semiconductor laser by coherent photon seeding

We have used coherent photon seeding to reduce the noise in an actively mode-locked extended-cavity semiconductor laser. Feedback is provided by an auxiliary cavity terminated either by a wedge plate or by a phase-conjugate mirror. Both conventional and phase-conjugate feedback can reduce the low-frequency noise components (0-5 MHz) by as much as 36 dB, hence drastically reducing the pulse fluctuations. A noise reduction of as much as 18 dB is also observed in the 0.01-3.0-GHz frequency range. We obtained these results while preserving the pulse duration (26 ps) and improving the time-bandwidth product.     

Design and experimental tests of active control barriers for low-frequency stationary noise reduction in urban outdoor environment

Active noise control (ANC) techniques are based on the emission of an antiphase signal in order to cancel the noise produced by a primary source. ANC has been successfully applied especially for reducing noise in confined environments, such as headphones and ducts. In this study, we present an application of ANC concepts to the design of an anti-noise barrier for an outdoor environment and its experimental testing. Even though passive techniques are effective in noise reduction at middle-high frequencies, they become less efficient at low frequencies (below 300 Hz) due to the limited dimensions of commonly deployable barriers. In this paper, we analyze the properties of a low-cost active noise system able to efficiently operate on stationary, almost pure-tone, low-frequency noise, such as that produced by electrical transformers and reactors in power and transformation plants. A prototype has been implemented and on-the-field experimental tests have been carried out. The results (confirmed also by numerical simulations) demonstrate a remarkable efficiency in the far field, with a reduction up to 15 dB with respect to the absence of the ANC system.     

Reduction of radiated exterior noise from the flexible vibrating plate of a rectangular enclosure using multi-channel active control

This study attempted to control the radiated exterior noise from a rectangular enclosure in which an internal plate vibrates by acoustic excitation and noise is thus radiated from that plate. Multi-channel active control was applied to reduce the vibration and external radiation of this enclosed plate. A piezoelectric ceramic was used as a distributed actuator for multiple mode control of the vibration and radiated noise in the acoustically excited plate. To maximize the effective control, an approach was proposed for attachment the piezoelectric actuator in the optimal location. The plate and internal acoustic space in the enclosure are coupled with each other. This will change dominant frequency characteristics of the plate and, thus, those of the externally radiated noise. Active noise control was accomplished using an accelerometer attached to the plate and a microphone placed adjacent to that plate as an error sensor under acoustic excitation of sine wave and white noise. It was found that the control of radiated external radiation noise requires a microphone as an error sensor, a sound pressure sensor due to vibration of the plate, differences in the dominant frequency of externally radiated noise, and complex vibration modes of the plate.