碳化钨对激光熔覆高熵合金的影响

为了获得高性能的涂层材料,采用激光熔覆的方法,在Q235钢基体上制备了FeSiCrCoMo高熵合金涂层,并研究了WC对高熵合金涂层的组织和性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、磨损试验机分别研究了添加WC前后涂层的微观形貌、相结构、硬度及磨损性能。结果表明:高熵合金FeSiCrCoMo涂层组织为粗大枝状晶,主要由BCC相和金属间化合物构成,添加WC后,涂层中形成了致密细小的胞状晶,同时BCC相增多,金属间化合物明显减少;添加WC后涂层的硬度明显增强,平均硬度提升了23%,涂层表面平均硬度达到了687HV0.2;WC的添加使得涂层的摩擦系数减小,磨损率减小,耐磨性能提高。     

激光熔覆FeCrNiMnMoxB0.5高熵合金涂层组织与耐蚀性能

为了获得性能优异的涂层材料,采用激光熔覆的方法在Q235钢基体上制备了不同Mo含量的FeCrNiMnMoB0.5系高熵合金涂层,着重探究Mo对高熵合金组织与性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、电化学工作站分别研究了高熵合金涂层的显微组织、相结构、显微硬度及耐蚀性能。结果表明:FeCrNiMnMoB0.5系高熵合金组织为树枝晶,主要由fcc相和少量金属间化合物构成。当添加少量Mo时,涂层的硬度较低,为290 HV,随着Mo的增加,晶格畸变加剧,出现少量金属化合物,涂层硬度最大增加到658 HV。在模拟饱和盐水泥浆溶液中FeCrNiMnMo0.4B0.5表现出较好的耐腐蚀性。     

激光熔覆Al2O3/Fe901复合涂层的强化机制及耐磨性

为提高金属材料表面涂层的耐磨性,采用激光熔覆工艺制备了Al_2O_3增强Fe901金属陶瓷复合涂层,研究了Al_2O_3陶瓷增强相对Fe基熔覆层组织与性能的影响。利用扫描电镜和X射线衍射仪检测了复合涂层的微观组织和物相;采用显微硬度仪和摩擦磨损试验机分析了复合涂层的显微硬度与耐磨性。结果表明:Fe901涂层的组织以柱状枝晶和等轴枝晶为主,添加的Al_2O_3可促使涂层组织转变为均匀的白色网状晶间组织及其包裹的细小黑色晶粒;复合涂层中的Al_2O_3陶瓷颗粒表面发生微熔,与Fe、Cr结合生成Fe3Al及(Al,Fe)4Cr金属间化合物,起到增加Al_2O_3陶瓷颗粒与金属黏结相结合强度的作用;当Al_2O_3陶瓷颗粒的质量分数为10%时,复合涂层的显微硬度较Fe901涂层增加了16.4%,复合涂层的摩擦磨损质量损失较Fe901涂层降低了50%;添加适量的Al_2O_3陶瓷有助于提高涂层的显微硬度及耐磨性。     

铝合金表面激光沉积AlCrFeCoNiCu涂层的组织及耐蚀性能

为了提高铝合金表面的力学和耐腐蚀性能,利用激光沉积技术在铝合金表面制备了AlCrFeCoNiCu高熵合金涂层。使用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、能谱分析仪(EDS)、显微硬度计和电化学工作站,研究了涂层的相结构、微观组织、元素分布、硬度及耐腐蚀性能。结果表明,涂层与基材结合良好,基材中Al元素在熔池搅拌作用下上浮,使沉积层呈FCC相和BCC相;显微组织为典型的枝晶结构,Cu元素在枝晶间富集;涂层平均显微硬度为528HV_(0.2),约是基材的5倍;AlCrFeCoNiCu涂层在3.5% NaCl溶液中的腐蚀特征为点蚀和晶间腐蚀,耐腐蚀性优于基材。激光沉积制备的AlCrFeCoNiCu高熵合金可以改善铝合金表面性能。     

镍基非晶复合涂层激光制备及其纳米压痕测试

采用大功率半导体激光熔覆和重熔的工艺在低碳钢表面制备Ni-Fe-B-Si-Nb合金非晶复合涂层,并对所得涂层进行了纳米压痕性能测试。研究结果表明,当激光熔覆时激光功率为0.8kW,熔覆速度为0.36m/min,送粉速度为12g/min,重熔时激光功率为3.5kW,熔覆速度为8m/min,在低碳钢表面成功制备了Ni40.8Fe27.2B18Si10Nb4非晶复合涂层,涂层主要由非晶相和NbC颗粒相组成。纳米压痕测试结果表明经激光重熔后所得非晶复合涂层的显微硬度和弹性模量远远大于未重熔的熔覆层,并且也大于同成分大块非晶。     

Ti6Al4V合金表面激光沉积复合涂层的组织和性能

为了增强Ti6Al4V钛合金的耐磨性,采用激光沉积制造方法在其表面上制备了以原位生成的TiC颗粒和直接添加的WC颗粒为增强相的耐磨涂层,观察了各涂层的微观组织,并测量了涂层的显微硬度和涂层在室温大气条件下的摩擦磨损性能。结果表明各涂层和基体呈现冶金结合,原位自生的TiC和部分熔化的WC颗粒均能够均匀弥散分布于基体上,由于增强相颗粒的弥散强化及激光沉积组织的细晶强化作用,基材的硬度和耐磨性均得到了提高。原位自生的TiC涂层比WC涂层硬度梯度分布平缓,但耐磨性稍差。     

TiN对Co基合金激光熔覆层组织与性能的影响

采用5 kW CO2激光器在低碳钢表面熔覆Co基合金涂层及TiN/Co基合金复合涂层,研究了两种涂层的组织、显微硬度以及滑动磨损性能。结果表明,Co基合金涂层主要组成相为-γCo,-εCo,Cr23C6等,TiN/Co基合金复合涂层组成相为-γCo,-εCo,Cr23C6,TiN和TiC等。Co基合金涂层由发达的-γCo枝晶和其间共晶组织所组成,TiN/Co基合金涂层典型组织为等轴固溶体以及细小的共晶组织。TiN对熔覆层的组织有显著的改善作用,促使其组织细化,树枝晶向等轴晶转化,同时可显著提高Co基合金涂层的显微硬度及耐磨性能。     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

稀土CeO_2对镍基纳米Al_2O_3激光熔覆复合涂层组织和性能的影响

采用激光熔覆技术在45钢基体上制备了不同CeO2含量的镍基纳米Al2O3复合涂层,对熔覆层进行了微观组织分析和显微硬度测试。结果表明,随着CeO2含量的增加,熔覆层组织由亚共晶向共晶组织转变;加入1.0%CeO2对镍基纳米Al2O3熔覆层的组织起到明显的细化和净化作用,枝晶生长的方向性减弱,组织趋向均匀,熔覆涂层的显微硬度值比未加稀土的涂层提高了60-95HV0.2。     

激光工艺参数对钛合金表面NiCrBSi合金熔覆层组织及硬度的影响

在TC4合金表面进行了激光熔覆NiCrBSi合金涂层的试验 ,利用SEM和XRD等对熔覆层的微观组织进行了分析 ,测试了熔覆层的显微硬度。结果表明 ,激光工艺参数对熔覆层的组织和硬度有极大的影响 ,随稀释率的增加 ,激光熔覆层中形成了TiB2 和TiC等颗粒增强相 ,熔覆层的硬度明显提高。     

Microstructure and properties of 6FeNiCoSiCrAlTi high-entropy alloy coating prepared by laser cladding

The content of each constituent element in the newly developed high-entropy alloys (HEAs) is always restricted in equimolar or near-equimolar ratio in order to avoid the formation of complex brittle phases during the solidification process. In this study, a 6FeNiCoSiCrAlTi high-entropy alloy coating with simple BCC solid solution phase has been prepared by laser cladding on a low carbon steel substrate. The microstructure, hardness and magnetic properties have been investigated. The experimental results show that the tendency of component segregation in the conventional solidification microstructure of multi-component alloy is effectively relieved. The microstructure of the coating is mainly composed of equiaxed polygonal grains, discontinuous interdendritic segregation and nano-precipitates. EBSD observation confirms that the polygonal grains and interdendritic segregation have similar BCC structure with lots of low angle grain boundaries at the interface. The microhardness of the coating reaches 780 HV_0.5, which is much higher than most of the HEAs prepared by other methods. In addition, the coating shows excellent soft magnetic properties.     

Reactive plasma cladding of TiC/Fe cermet coating using asphalt as a carbonaceous precursor

A new process of preparing Ti-Fe-C composites powder for reactive plasma cladding, precursor carbonization-composition process, was developed. TiC/Fe cermet coatings were synthesized by reactive plasma cladding of the composite powder. XRD and SEM were employed to analyze the phase composition and microstructure of the composite powder and coating. The hardness and wear resistance of the coating was tested. Results show that: The compound powder prepared by precursor carbonization-composition process has very tight structure, which can avert the question of raw powder breaking-up in cladding process. The TiC/Fe cermet coating by reactive plasma cladding consists of alternate, laminated layers as following: the layers in which the round nanoscale TiC particles are dispersed within the α-Fe matrix and the layers of TiC accumulation. The TiC/Fe cermet coating by reactive plasma cladding shows superior hardness and wear resistance: The surface hardness of the TiC/Fe cermet coating is 68 ± 6 (HR30 N). In the same fretting conditions, the wear resistance of Ni60 coating is twelve times than that of the TiC/Fe cermet coating.     

快冷熔覆法原位合成大厚度铁基非晶复合涂层的研究

通过水冷提高凝固速率及降低基体金属对熔覆层的稀释,采用改进的钨极惰性气体氩弧熔覆的方法,原位制备了大厚度(1—5 mm)Fe基非晶/纳米晶复合涂层.利用X射线衍射,光学显微镜和透射电子显微镜对涂层成分和组织进行分析,并测试了涂层的显微硬度.结果表明,采用快冷熔覆的方法可以制备出含有50%以上非晶含量的非晶/纳米晶复合涂层,涂层内纳米晶颗粒表面被非晶过渡层包覆.较厚涂层的显微硬度达到1600HV_0.3,与基体为冶金连接,有良好的结合强度及耐磨性.非晶/纳米晶复合结构使得涂层与基体之间的过渡区具备较强的弹塑性,提高了涂层的抗冲击性. 最后重点讨论了微观结构和性能之间的内在联系,涂层内非晶相与纳米晶相的协同作用是造成涂层高硬度的主要原因. 关键词： 非晶 涂层 熔覆 显微硬度     

Microstructure and tribological properties of TiAg intermetallic compound coating

TiAg intermetallic compound coating has been in situ synthesized successfully on pure Ti substrate by laser cladding using Ag powder as the precursor. It has been found that the prepared coating mainly comprised TiAg and Ti phases. The high resolution transmission electron microscopy results further conform the existence of TiAg intermetallic compound in the prepared coating. The magnified high resolution transmission electron microscopy images shown that the laser cladding coating contains TiAg nanocrystalline with the size of about 4 nm. Tribological properties of the prepared TiAg intermetallic compound coating were systematically evaluated. It was found that the friction coefficient and wear rate was closely related to the normal load and sliding speed, i.e., the friction coefficient of the prepared TiAg intermetallic compound coating decreased with increasing normal load and sliding speed. The wear rate of the TiAg intermetallic compound coating decreased rapidly with increasing sliding speed, while the wear rate increased as the normal load increased.     

激光熔覆原位合成Nb(C,N)陶瓷颗粒增强铁基金属涂层

采用预涂粉末激光熔覆技术,在42CrMo基体上制备出原位合成Nb(C, N)颗粒增强的铁基复合涂层。X射线及扫描电镜分析结果表明:激光熔覆获得的涂层基体为耐氧化、耐蚀性良好的Fe-Cr细晶组织及少量的-Fe相,原位合成的Nb（C, N）呈块状弥散分布在基体上。进一步的磨损试验表明:这些颗粒增强相极大增强了抗磨损性能,与未熔覆的母材相比,其磨损失重仅为母材的1/9左右; 涂层在750 ℃恒温氧化条件下具有较好的抗氧化性能,氧化层主要由NbO1.1,Cr2O3相组成; 母材的氧化产物为Fe2O3,容易脱落,保护性能较差; 激光熔覆涂层的氧化膜厚度仅为未涂层的1/5。     

激光熔覆Al+SiC涂层对镁合金表面耐磨性能的改性

通过脉冲激光器(Nd-YAG)在AZ91D镁合金基底上熔覆Al+SiC粉体。采用扫描电子显微镜、能量色散谱(EDS)和X-射线衍射测定分析熔覆层的显微组织、化学成分和物相组成。研究表明:Al+SiC涂层主要由SiC,β-Mg_(17)Al_(12)及Mg和Al相组成,激光熔覆层与镁合金基底表现出良好的冶金结合。所有样品都具有树枝状结构,且随着SiC质量分数的增大,树枝状和胞状结构的间隔变得更大。熔覆涂层的表面硬度高于基底,并且随着熔覆层中的SiC质量分数的增加而增大,SiC质量分数为40%的熔覆层具有最大的显微硬度,达到180 HV,然而质量分数为10%的熔覆层硬度为136 HV。销盘滑动磨损试验表明,复合涂层中的SiC颗粒和原位合成的Mg_(17)Al_(12)相显著提高了AZ91D镁合金的耐磨损性,其中,SiC质量分数从10%增加到30%过程中磨损体积损失逐渐减少,SiC质量分数在20%~30%时熔覆层具有最好的耐磨性。     

磁场辅助激光熔覆制备Ni60CuMoW复合涂层

采用磁场辅助激光熔覆技术,在Q235钢表面制备了Ni60CuMoW复合涂层,借助SEM,EDS 和XRD 等表征手段对涂层进行了微观组织和物相分析,利用维氏硬度计测试了复合涂层截面的显微硬度分布,通过摩擦磨损实验和电化学测试系统研究了复合涂层的磨损性能和耐腐蚀性能。研究结果表明:涂层主要由-Ni,Cu）固溶体、硅化物和硼化物组成,Cr3Si晶粒细化且均匀致密;磁场辅助作用下,激光熔覆涂层平均显微硬度达到913HV0.5,为无磁场辅助涂层的1.5 倍,磨损失重仅为无磁场涂层的36%,自腐蚀电位上升了100 mV,腐蚀电流密度降低了70%,耐磨耐蚀性能得到了显著改善。     

Synthesis and microstructure observation of titanium carbonitride nanostructured coatings using reactive plasma spraying in atmosphere

In the present study, nanostructured titanium carbonitride (TiCN) coatings were successfully deposited by reactive plasma spraying (RPS) technology using a self-designed gas tunnel mounted on a normal plasma spray torch. The phase composition and microstructure of the TiCN coatings were characterised by XRD, SEM and TEM. The results indicated that the main phase of the coatings was FCC TiC_0.2N_0.8 with a small amount of Ti₃O. The coating that was deposited using 35 kW displayed better microstructure and properties. The coating exhibited a typical nanostructure including 90 nm diamertrical equiaxed grains and 400 nm long columnar grains by TEM images. The SEM observation further revealed that the equiaxed grains in parallel direction to the substrate surface in TEM images were actually the columnar grains perpendicular to the substrate surface. The formation mechanism of the nanostructured coatings was also discussed. The measured microhardness value of the coating was approximately 1659 Hv_100 g, and the calculated crack extension force was about 34.9 J/m².