镍基非晶复合涂层激光制备及其纳米压痕测试

采用大功率半导体激光熔覆和重熔的工艺在低碳钢表面制备Ni-Fe-B-Si-Nb合金非晶复合涂层,并对所得涂层进行了纳米压痕性能测试。研究结果表明,当激光熔覆时激光功率为0.8kW,熔覆速度为0.36m/min,送粉速度为12g/min,重熔时激光功率为3.5kW,熔覆速度为8m/min,在低碳钢表面成功制备了Ni40.8Fe27.2B18Si10Nb4非晶复合涂层,涂层主要由非晶相和NbC颗粒相组成。纳米压痕测试结果表明经激光重熔后所得非晶复合涂层的显微硬度和弹性模量远远大于未重熔的熔覆层,并且也大于同成分大块非晶。     

Ti6Al4V合金表面激光沉积复合涂层的组织和性能

为了增强Ti6Al4V钛合金的耐磨性,采用激光沉积制造方法在其表面上制备了以原位生成的TiC颗粒和直接添加的WC颗粒为增强相的耐磨涂层,观察了各涂层的微观组织,并测量了涂层的显微硬度和涂层在室温大气条件下的摩擦磨损性能。结果表明各涂层和基体呈现冶金结合,原位自生的TiC和部分熔化的WC颗粒均能够均匀弥散分布于基体上,由于增强相颗粒的弥散强化及激光沉积组织的细晶强化作用,基材的硬度和耐磨性均得到了提高。原位自生的TiC涂层比WC涂层硬度梯度分布平缓,但耐磨性稍差。     

激光熔覆NiCrBSi涂层组织及摩擦磨损性能

采用激光熔覆技术在H13钢表面制备了NiCrBSi合金涂层,利用OM,SEM,EDX和XRD等对熔覆层的微观组织进行了分析,测试了熔覆层的显微硬度和摩擦磨损性能。结果表明,激光熔覆层与基体形成了良好的冶金结合,熔覆层的组织主要由γ-Ni,Cr7C3和CrB等相组成。熔覆层显微硬度在650~850HV之间,明显高于H13钢基体的硬度。摩擦磨损实验表明,在相同的条件下,熔覆层的耐磨性比基体有了明显的提高,磨损体积减少了92.4%。通过对磨损后的试样进行粗糙度测试后表明,涂层具有更平滑的表面。     

磁场辅助激光熔覆制备Ni60CuMoW复合涂层

采用磁场辅助激光熔覆技术,在Q235钢表面制备了Ni60CuMoW复合涂层,借助SEM,EDS 和XRD 等表征手段对涂层进行了微观组织和物相分析,利用维氏硬度计测试了复合涂层截面的显微硬度分布,通过摩擦磨损实验和电化学测试系统研究了复合涂层的磨损性能和耐腐蚀性能。研究结果表明:涂层主要由-Ni,Cu）固溶体、硅化物和硼化物组成,Cr3Si晶粒细化且均匀致密;磁场辅助作用下,激光熔覆涂层平均显微硬度达到913HV0.5,为无磁场辅助涂层的1.5 倍,磨损失重仅为无磁场涂层的36%,自腐蚀电位上升了100 mV,腐蚀电流密度降低了70%,耐磨耐蚀性能得到了显著改善。     

激光熔覆TiC陶瓷涂层的组织和摩擦磨损性能研究

采用激光熔覆技术在TC4合金表面上制备了TiC陶瓷涂层,分析了熔覆层的微观组织,测试了熔覆层的硬度和摩擦磨损性能。结果表明:TiC激光熔覆层分为熔覆区和稀释区两个区域,熔覆区未受到基底的稀释,由TiC颗粒和TiC树枝晶组成;稀释区受到了基底的稀释,由TiC树枝晶和钛合金组成;TiC激光熔覆层的显微硬度在HV700~1500之间,明显地改善了TC4合金表面的摩擦和磨损性能。     

快冷熔覆法原位合成大厚度铁基非晶复合涂层的研究

通过水冷提高凝固速率及降低基体金属对熔覆层的稀释,采用改进的钨极惰性气体氩弧熔覆的方法,原位制备了大厚度(1—5 mm)Fe基非晶/纳米晶复合涂层.利用X射线衍射,光学显微镜和透射电子显微镜对涂层成分和组织进行分析,并测试了涂层的显微硬度.结果表明,采用快冷熔覆的方法可以制备出含有50%以上非晶含量的非晶/纳米晶复合涂层,涂层内纳米晶颗粒表面被非晶过渡层包覆.较厚涂层的显微硬度达到1600HV_0.3,与基体为冶金连接,有良好的结合强度及耐磨性.非晶/纳米晶复合结构使得涂层与基体之间的过渡区具备较强的弹塑性,提高了涂层的抗冲击性. 最后重点讨论了微观结构和性能之间的内在联系,涂层内非晶相与纳米晶相的协同作用是造成涂层高硬度的主要原因. 关键词： 非晶 涂层 熔覆 显微硬度     

碳化钨对激光熔覆高熵合金的影响

为了获得高性能的涂层材料,采用激光熔覆的方法,在Q235钢基体上制备了FeSiCrCoMo高熵合金涂层,并研究了WC对高熵合金涂层的组织和性能的影响。通过金相、X射线衍射、扫描电镜、硬度计、磨损试验机分别研究了添加WC前后涂层的微观形貌、相结构、硬度及磨损性能。结果表明:高熵合金FeSiCrCoMo涂层组织为粗大枝状晶,主要由BCC相和金属间化合物构成,添加WC后,涂层中形成了致密细小的胞状晶,同时BCC相增多,金属间化合物明显减少;添加WC后涂层的硬度明显增强,平均硬度提升了23%,涂层表面平均硬度达到了687HV0.2;WC的添加使得涂层的摩擦系数减小,磨损率减小,耐磨性能提高。     

钛合金表面激光熔覆TiC_p/Ni基合金复合耐磨涂层

采用激光熔覆技术在TC4合金表面制备TiC颗粒增强的Ni基合金复合材料涂层,测试了熔覆层的硬度和滑动摩擦磨损性能,分析了熔覆层的强化机制。结果表明,熔覆层中存在颗粒强化、固溶强化和细晶强化等多种强化作用,熔覆层的显微硬度达HV900～1100,耐磨性能比TC4合金显著提高。     

铁基合金激光熔覆层高温润滑磨损性能

 为提高40Cr合金钢的表面耐磨性,采用预置激光熔覆法在40Cr基体表面制备铁基合金涂层, 利用扫描电镜观察分析熔覆层显微组织形貌,用显微硬度仪测试熔覆层截面显微硬度,用摩擦磨损试验机测定在润滑条件下基体、熔覆层的摩擦系数随温度变化的规律。研究结果表明:熔覆层与基体实现良好冶金结合,熔覆层横截面微观组织呈现平面晶、树枝晶和胞状晶分布;熔覆层硬度值介于617.5~926.6 HV0.2之间,基体硬度介于205.2~278.2 HV0.2之间;在200 ℃以下,熔覆层摩擦系数在磨程中趋于平稳,在0.1附近轻微波动,小于基体平均摩擦系数;当温度超过200 ℃,油膜分解,引发润滑失效,磨损方式向干摩擦转化,磨损机理从微切削磨损主导向粘着磨损、磨粒磨损和氧化磨损复合磨损方式转化。     

激光熔覆Al+SiC涂层对镁合金表面耐磨性能的改性

通过脉冲激光器(Nd-YAG)在AZ91D镁合金基底上熔覆Al+SiC粉体。采用扫描电子显微镜、能量色散谱(EDS)和X-射线衍射测定分析熔覆层的显微组织、化学成分和物相组成。研究表明:Al+SiC涂层主要由SiC,β-Mg_(17)Al_(12)及Mg和Al相组成,激光熔覆层与镁合金基底表现出良好的冶金结合。所有样品都具有树枝状结构,且随着SiC质量分数的增大,树枝状和胞状结构的间隔变得更大。熔覆涂层的表面硬度高于基底,并且随着熔覆层中的SiC质量分数的增加而增大,SiC质量分数为40%的熔覆层具有最大的显微硬度,达到180 HV,然而质量分数为10%的熔覆层硬度为136 HV。销盘滑动磨损试验表明,复合涂层中的SiC颗粒和原位合成的Mg_(17)Al_(12)相显著提高了AZ91D镁合金的耐磨损性,其中,SiC质量分数从10%增加到30%过程中磨损体积损失逐渐减少,SiC质量分数在20%~30%时熔覆层具有最好的耐磨性。     

Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate

Three kinds of laser boronizing composite coatings were in situ synthesized on Ti substrate by using powders of B, BN and B₄C as starting materials. Microstructures of the laser boronizing composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM); and their worn surface morphologies were also observed by using SEM. Moreover, the friction and wear behavior of the boronizing composite coatings under dry sliding condition were evaluated using a UMT-2MT friction and wear tester. It was found that all the three types of laser boronizing composite coatings had higher microhardness and better wear resistance than pure Ti substrate; and their microstructure and wear resistance varied with varying pre-placed powders of B, BN, and B₄C. Under the same dry sliding test conditions, the wear resistance of the three kinds of laser boronizing composite coatings, i.e., sample 1 prepared from pre-placed B, sample 2 obtained from pre-placed BN, and sample 3 fabricated from pre-placed B₄C, is ranked in an order of sample 1 > sample 2 > sample 3, which, surprisingly, well conforms to their order of hardness and friction coefficients.     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Preparation and characteristics of three-layer YSZ-(YSZ/Al2O3)-YSZ TBCs

Novel three-layer YSZ-(YSZ/Al₂O₃)-YSZ (6 wt.% Y₂O₃ partially stabilized ZrO₂) thermal barrier coatings (TBCs) were successfully prepared on Ni-based superalloy substrate using composite sol-gel and pressure filtration microwave sintering (PFMS) techniques. The coatings were evaluated for the cyclic oxidation resistance, thermal barrier effect and the presences of phases and microstructures. FE-SEM results indicate that the coatings were dense and crack-free. The coatings maintained their structural integrity when they were exposed at 1100 for 100 h. They exhibited superior oxidation resistance, spallation resistance and thermal insulation property compared with single-layer YSZ coatings. Moreover, the detailed mechanisms were discussed in order to understand the improved performance of the three-layer TBCs.     

Preparation and properties of titanium oxide film on NiTi alloy by micro-arc oxidation

Titanium oxide ceramic coatings were prepared by micro-arc oxidation (MAO) in galvanostatic regime on biomedical NiTi alloy in H₃PO₄ electrolyte using DC power supply. The surface of the coating exhibited a typical MAO porous and rough structure. The XPS analysis indicated that the coatings were mainly consisted of O, Ti, P, and a little amount of Ni, and the concentration of Ni was greatly reduced compared to that of the NiTi substrate. The TF-XRD analysis revealed that MAO coating was composed of amorphous titanium oxide. The coatings were tightly adhesive to the substrates with the bonding strength more than 45 MPa, which was suitable for medical applications. The curves of potentiodynamic porlarization indicated that the corrosion resistance of NiTi alloy was significantly improved due to titanium oxide formation on NiTi alloy by MAO.     

Deposition of duplex Al2O3/aluminum coatings on steel using a combined technique of arc spraying and plasma electrolytic oxidation

Plasma electrolytic oxidation (PEO) is a cost-effective technique that can be used to prepare ceramic coatings on metals such as Ti, Al, Mg, Nb, etc., and their alloys, but this promising technique cannot be used to modify the surface properties of steels, which are the most widely used materials in engineering. In order to prepare metallurgically bonded ceramic coatings on steels, a combined technique of arc spraying and plasma electrolytic oxidation (PEO) was adopted. In this work, metallurgically bonded ceramic coatings on steels were obtained using this method. We firstly prepared aluminum coatings on steels by arc spraying, and then obtained the metallurgically bonded ceramic coatings on aluminum coatings by PEO. The characteristics of duplex coatings were analyzed by X-ray diffractometer (XRD) and scanning electron microscopy (SEM). The corrosion and wear resistance of the ceramic coatings were also studied. The results show that, duplex Al₂O₃/aluminum coatings have been deposited on steel substrate after the combined treatment. The ceramic coatings are mainly composed of α-Al₂O₃, γ-Al₂O₃, θ-Al₂O₃ and some amorphous phase. The duplex coatings show favorable corrosion and wear resistance properties. The investigations indicate that the combination of arc spraying and plasma electrolytic oxidation proves a promising technique for surface modification of steels for protective purposes.     

Characterization and oxidation behavior of NiCoCrAlY coating fabricated by electrophoretic deposition and vacuum heat treatment

Electrophoretic deposition (EPD) was showed to be a feasible and convenient method to fabricate NiCoCrAlY coatings on nickel based supperalloys. The microstructure and composition of the NiCoCrAlY coatings after vacuum heat treatment were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDAX). Isothermal-oxidation test was performed at 1100 °C in static air for 100 h. The results show that the major phases in electrophoretic deposited and vacuum heat treated NiCoCrAlY coating are γ-Ni and γ′-Ni₃Al phases, also there is an extremely small quantity of Al₂O₃ in the coating. Composition fluctuations occur in the coating and a certain amount of titanium diffuse from the superalloy substrate to the top of the coating during vacuum heat treatment. The oxidation test results exhibit that the oxidation kinetics of this coating has two typical stages. The protective oxide layer is mainly formed in the initial linear growth stage and then the oxide layer hinders further oxidation of the coating in the subsequent parabolic growth stage. The coating can effectively protect the superalloy substrate from oxidation. A certain amount of rutile TiO₂ is formed in the coating during oxidation and it is adverse to the oxidation resistance of the coating.     

Wear resistance of reactive plasma sprayed and laser remelted TiB2-TiC0.3N0.7 based composite coatings against medium carbon steel

Wear resistance of reactive plasma sprayed TiB₂-TiC_0.3N_0.7 based composite coatings and the as-sprayed coating with laser surface treatment was investigated using plate-on-plate tests. Wear tests were performed at different normal loads and sliding speeds under dry sliding conditions in air. The surface morphologies of counterparts against as-sprayed and laser remelted coatings were investigated. The microstructure and chemical composition of wear debris and coatings were studied using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS), respectively. The results show that the wear resistance of the laser remelted coating is improved significantly due to their increased microhardness and reduced flaws. The primary wear mechanism of the remelted coating is oxidation wear and its minor wear mechanisms are grain abrasion and fatigue failure during the course of wear test. In contrast, the primary wear mechanism of the as-sprayed coating is grain abrasion at the low sliding speed (370 rpm) and fatigue failure at the high sliding speed (549 rpm). The oxidation wear mechanism is a minor contributor for the as-sprayed coating.     

Preparation and properties of electroless Ni-P-SiO2 composite coatings

Dispersible SiO₂ nanoparticles were co-deposited with electroless Ni-P coating onto AISI-1045 steel substrates in the absence of any surfactants in plating bath. The resulting Ni-P/nano-SiO₂ composite coatings were heat-treated for 1 h at 200 °C, 400 °C, and 600 °C, respectively. The hardness and wear resistance of the heat-treated composite coatings were measured. Moreover, the structural changes of the composite coatings before and after heat treatment were investigated by means of X-ray diffraction (XRD), while their elemental composition and morphology were analyzed using an energy dispersive spectrometer (EDS) and a scanning electron microscope (SEM). Results show that co-deposited SiO₂ particles contributed to increase the hardness and wear resistance of electroless Ni-P coating, and the composite coating heat-treated at about 400 °C had the maximum hardness and wear resistance.