Efficient diode-end-pumped dual-wavelength Nd, Gd:YSGG laser

We demonstrate a dual-wavelength laser based on a new laser material-Nd, Gd:YSGG, or Nd:GYSGG for short-for the first time to our knowledge. Besides its attractive properties such as antiradiation, high segregation coefficient, etc., this kind of laser crystal also shows excellent laser performance. For continuous-wave operation, the maximum output power is 10.1 W with the absorbed power of 18.45 W at 808 nm, corresponding to the slope efficiency of nearly 60%. The maximum single pulse energy and peak power reach 277 μJ and 4.6 kW (60 ns) when the absorbed pump power is 11.4 W for acousto-optic Q-switched operation.     

基于多层石墨烯可饱和吸收体的被动调Q Ho∶YAG激光器

报道了2μm被动调Q的Ho∶YAG激光器,该激光器采用Tm~(3+)光纤激光器作为泵浦源,使用多层石墨烯作为可饱和吸收体。在连续波激光输出模式下,当泵浦功率为4.2 W时,获得了750 mW激光输出,输出激光中心波长为2.09μm,斜率效率为29.6%。在连续波激光器谐振腔中插入多层石墨烯可饱和吸收体并调整谐振腔,获得了脉冲激光输出。当泵浦功率为4.2 W时,获得最小脉冲宽度3.1μs、重复频率66.6 kHz的脉冲激光输出,其最大平均输出功率为170 mW,斜率效率为12.6%,光束质量因子M_x~2=1.15,M_y~2=1.12。     

Efficient continuous wave and Q-switched operation of a dual-end-pumped <Emphasis Type="Italic">c</Emphasis>-cut Tm:YAP laser

An efficient continuous wave (CW) and Q-switched c-cut Tm:YAP laser is reported in this letter. With the dual-end-pumped convex-concave resonator, CW output power up to 13.6 W at 1.99 μm was obtained under a total incident pump power of 50 W. The corresponding slope efficiency was 34.3% and conversion efficiency was 27.2%. The active Q-switched operation of the laser had an average output power of 12.5 W at 10 kHz pulse repetition frequency, with a minimum pulse width of 126 ns. With 6 kHz pulse repetition frequency, the maximum pulse energy of 1.6 mJ was obtained. In addition, using the Tm:YAP laser as a pumping source for gain-switched Cr:ZnSe laser, as much as 4 W output power in the wavelength range of 2.5–2.6 μm was obtained.     

Highly efficient in-band pumped Er:YAG laser with 60 W of output at 1645 nm

A high-power Er:YAG laser that is in-band pumped by a high-power cladding-pumped erbium-ytterbium codoped fiber laser operating at 1532 nm is reported. The Er:YAG laser produced 60.3 W of continuous-wave output at 1645.3 nm in a beam with M2 approximately equal to 3 for 82 W of incident pump power and 20 W of TEM00 output with M2 < 1.2 for 32.4 W of incident pump power. The slope efficiency with respect to incident pump power at pump powers of >20 W was approximately 81%. In the Q-switched mode of operation, a slightly modified resonator configuration incorporating an electro-optic Q switch produced pulses of approximately 4 mJ energy and approximately 100 ns (FWHM) duration, corresponding to a peak power of approximately 42 kW at a repetition rate of 1 kHz for an incident pump power of 16.8 W. The prospects for further improvement in continuous-wave and Q-switched performance are discussed.     

Efficient Tm:YLF laser with a volume Bragg grating recycle pumped by laser diode

By using a pump recycling configuration, we presented a high efficient diode-pumped Tm:YLF laser with a volume Bragg grating. When the incident pump power was 33.1 W, a maximum output power of 11.1 W at 1907.8 nm with full width at half maximum of 0.6 nm was obtained. The slope efficiency with respect to the incident pump power was 44.8%, and the optical-to-optical efficiency was 33.5%. In addition, the VBG-based Tm:YLF laser was employed as a pumping source of Ho:YAG laser, the maximum output power of 4.7 W with a slope efficiency of 67.0% was obtained, corresponding to Tm-to-Ho conversion efficiency of 51.6%.     

Q-switched operation of <Emphasis Type="Italic">a</Emphasis>-cut Ho:YAlO<Subscript>3</Subscript> laser pumped by a diode-pumped 1.91 μm thulium laser

Q-switched operation of a room temperature Ho:YAP laser was resonantly end-pumped by a diode-pumped Tm:YLF laser at 1.91 μm. The CW Ho:YAP laser generated 9.9 W of linearly output at 2119.03 nm with beam quality factor of M ² ∼1.46 with respect to absorbed pump power of 19.16 W, corresponding to an optical-to-optical conversion efficiency of 51.7% and slope efficiency of 60.6%. Under Q-switched operation, the maximum output power of 9.8 W in relation to 10 kHz pulse repetition frequency (PRF) was obtained, however, the maximum peak power of 60 kW at the PRF of 5 kHz was demonstrated. At 5 kHz pulse energies of 1.92 mJ with pulse width of 32 ns was achieved.     

Q-switched operation of an in-band-pumped Ho:LuAG laser with kilohertz pulse repetition frequency

We report continuous-wave (CW) and repetitively Q-switched operation of an in-band-pumped Ho:LuAG laser at room temperature. End-pumped by a Tm:YLF solid-state laser with emission wavelength of 1.91 μm, the CW Ho:LuAG laser generated 5.4-W output at 2100.7 nm with beam quality factor of M ²～1.03 for an incident pump power of 14.1 W, corresponding to slope efficiency of 67% with respect to absorbed pump power. Up to 1.5-mJ energy per pulse at pulse repetition frequency (PRF) of 3 kHz and 4.5-W average power with FWHM pulse width of 28 ns at 5 kHz were demonstrated in repetitively Q-switched operation.     

Continuous-wave and Q-switched laser operation of Nd:Gd0.18Y0.82VO4 mixed crystal

Efficient continuous-wave (cw), passively Q-switched, and actively Q-switched laser operations are demonstrated with a mixed vanadate crystal of Nd:Gd_0.18Y_0.82VO₄ under diode pumping. In a cw operation, an output power of 8.25 W is obtained at a maximum available incident pump power (P_in) of 15 W, with a slope efficiency of 56%. Using a Cr⁴⁺:YAG crystal of initial transmission of 62% as the saturable absorber for Q-switching, an average output power of 3.05 W is generated at pulse repetition frequency (PRF) of 16.7 kHz when the laser is pumped with the same maximum P_in. The pulse energy, pulse duration, and peak power are 183.3 μJ, 6.0 ns, and 30.6 kW, respectively. When actively Q-switched by an acousto-optic modulator, the laser produces an average output power of 5.5 W at PRF of 30 kHz with 16.2 W of pump power incident upon the laser crystal. The pulse energy, duration, and peak power are measured to be 183 μJ, 10.5 ns, and 17.5 kW, respectively.     

Room temperature efficient continuous wave and Q-switched operation of a Ho:YAP laser

We report the continuous wave and acousto-optically Q-switched operation of a Tm:YLF-pumped Ho:YAP laser at room temperature. Continuous wave output power of 6.8 W at 2118 nm was obtained under the incident pump power of 13.4 W, corresponding to a slope efficiency of 65.6% and a conversion efficiency of 50.7%. For the Q-switched mode, a maximum pulse energy of 1.28 mJ and a minimum pulse width of 31 ns at the repetition rate of 5 kHz were achieved, resulting in a peak power of 41.3 kW. In addition, the Ho:YAP laser was employed as a pumping source of ZGP optical parametric oscillator, the total average output power of which was 3.2 W at 4.08 and 4.41 μm with a slope efficiency of 69.5%, corresponding to the diode-to-mid-IR conversion efficiency of 9.0%.     

The output characteristics of double-end-pumped Ho:LuAG laser at room temperature

Continuous-wave (CW) and Q-switched operation of a room-temperature Ho:LuAG laser was resonantly double-end-pumped by a diode-pumped Tm:YLF laser at 1.91 μm. The CW Ho: LuAG laser generated 24.5 W of linearly output at 2094.4 nm with beam quality factor of M ² = 1.11 ± 0.02 for an absorbed pump power of 44.0 W, corresponding to optical-to-optical conversion efficiency of 55.7% and slope efficiency of 60.5%. Under Q-switched operation, a maximum output power of 24.1 W with a slope efficiency of 58.1% at 12 kHz was obtained. Also, the minimum pulse width of 32 ns was achieved, corresponding to the peak power was 37.7 kW.     

包层泵浦的高功率掺铥光纤激光器

研究了一种输出功率高且光束质量好的包层泵浦的掺铥光纤激光器.当泵浦功率达到30 W时,该掺铥光纤激光器产生的最大输出功率是6.1 W,且波长在2 μm左右,斜率效率达到55.6%,产生激光的阈值是2.2 W.当输出功率为3.3 W时,测得光束质量M2X和M2Y分别为1.26和1.32.     

High repetition rate,high peak power acousto-optical Q-switched 946 nm Nd:YAG laser

A diode-end-pumped high repetition rate, high peak power acousto-optical (AO) Q-switched 946 nm Nd:YAG laser was demonstrated in this paper. In our experiments, a 20 mm miniature acousto-optical Q-switch was employed in a 45 mm linear laser cavity for generating the short laser pulse. At a repetition rate of 10 kHz, a maximum average output power of 2.9 W was achieved with a pulse width of 24.4 ns, giving a peak power of 11.9 kW. To the best of our knowledge, this is the highest peak power 946 nm Nd:YAG laser at high repetition rate operation. Moreover, pulse train with good stability was also obtained at the repetition rate of 50 kHz. At an incident pump power of 22.3 W, up to an average output power of 3.5 W pulsed 946 nm laser was generated at 50 kHz with a pulse width of 69 ns, corresponding to an optical conversion efficiency of 15.7% and an average slope efficiency of 24.1%, respectively.     

Continuous-wave and Q-switched Operation of a Tm,Ho:YAP ring laser

We demonstrated continuous-wave (CW) and Q-switched operation of a Tm,Ho:YAP ring laser at 77 K. The maximum CW output power of 2 W at 2130.7 nm was obtained under the incident pump power of 12 W, corresponding to a slope efficiency of 23% and an optical-to-optical efficiency of 16.7%. For the Q-switched regime the maximum output energy of 5 mJ with the pulse width of 160 ns at the repetition rate of 100 Hz was achieved, corresponding to a peak power of 31.25 kW.     

Efficient Nd:YVO_4 laser in-band pumped by wavelength-locked 913.9-nm laser diode and Q-switch operation

An efficient 1064-nm Nd:YVO_4laser in-band pumped by a wavelength-locked laser diode(LD) at 913.9 nm was demonstrated. The maximum continuous wave(CW) output power of 23.4 W at 1064 nm was realized with the incident pump power of 40 W, corresponding to a total optical-to-optical efficiency of 58.5%. This is to the best of our knowledge the highest total optical-to-optical efficiency and output power of Nd:YVO_4laser in-band pumped by a 913.9-nm laser diode.The Q-switched operation of this laser was also investigated. Through a contrast experiment of pumping at 808 nm, the experimental results showed that an Nd:YVO_4laser in-band pumped by a wavelength-locked LD at 913.9 nm had excellent pulse stability and beam quality for high repetition rate Q-switching operation.     

High-power Er:YAG laser with quasi-top-hat output beam

A simple method for simultaneously exciting the fundamental (TEM00) transverse mode and first order Laguerre-Gaussian (LG01) donut mode in an end-pumped solid-state laser to yield a quasi-top-hat output beam is reported. This approach has been applied to an Er:YAG laser, in-band pumped by an Er,Yb fiber laser, yielding 9.6 W of continuous-wave output at 1645 nm in a top-hat-like beam with beam propagation factor (M2)<2.1 for 24 W of incident pump power at 1532 nm. The corresponding slope efficiency with respect to incident pump power was 49%. The prospects of further scaling of output power and improved overall efficiency are considered.     

Diode-pumped high-repetition-rate acousto-optically Q-switched Nd:YVO<Subscript>4</Subscript> laser operating at 914 nm

A diode-pumped high-repetition-rate acousto-optically (A-O) Q-switched Nd:YVO₄ laser operating at 914 nm was reported in this paper. Employing a compact linear laser cavity, at an operating repetition rate of 10 kHz, a maximum average output power of 2.2 W 914 nm laser was obtained at an incident pump power of 45.3 W, corresponding to an optical conversion efficiency of 4.9% and a slope efficiency of 8.8%. Minimum pulse width of 24 ns and maximum peak power of 8.0 kW of 914 nm laser was also achieved at an incident pump power of 40.8 W. To the best of our knowledge, this is the highest peak power of 914 nm laser at 10 kHz by far. Moreover, the highest operating repetition rate of pulsed 914 nm can even reach 100 kHz.     

Efficient high-power Ho:YAG laser directly in-band pumped by a GaSb-based laser diode stack at 1.9 μm

An efficient high-power Ho:YAG laser directly in-band pumped by a recently developed GaSb-based laser diode stack at 1.9 μm is demonstrated. At room temperature a maximum continuous wave output power of 55 W at 2.122 μm and a slope efficiency of 62% with respect to the incident pump power were achieved. For narrow linewidth laser operation a volume Bragg grating was used as output coupler. In wavelength stabilized operation a maximum output power of 18 W at 2.096 μm and a slope efficiency of 30% were obtained. In this case the linewidth is reduced from 1.2 nm to below 0.1 nm. Also spectroscopic properties of Ho:YAG crystals at room temperature are presented.     

Generation of high power laser at 1314 nm from a diode-side-pumped Nd:YLF module

We demonstrate a high power continuous-wave （CW） and acoustic-optically （AO） Q-switched 1314-nm laser with a diode-side-pumped Nd：YLF module. A maximum CW output power of 21.6 W is obtained with a diode pump power of 180 W, corresponding to an optical-to-optical conversion efficiency of 12.0% and a slope efficiency of 16.1%. In the Q-switching operation, a highest pulse energy of 3.8 mJ is obtained at a pulse repetition rate of 1 kHz. The shortest pulse width and maximum single peak power are 101.9 ns and 37.3 kW, respectively.     

Widely Tunable Middle Infrared Optical Parametric Oscillator Pumped by the Q-Switched Ho:GdVO_4 Laser

We demonstrate a middle infrared ZnGeP_2 optical parametric oscillator pumped by the Q-switched Ho:GdVO_4 laser. When the incident Ho pump power is 4.12 W, the maximum average output power of the ZGP-OPO laser is 2.05 W, corresponding to a slope efficiency of 74.6%. The ZGP-OPO laser produces 4.2 ns mid-infrared pulses at a pulse repetition rate of 5 kHz. In addition, we obtain 0.8 um of tunable range for the signal wave and 2.1 um of tunable range for the idler wave.     

Power and radiance scaling of a 946 nm Nd:YAG planar waveguide laser

We present a diode-end-pumped Nd:YAG planar waveguide laser operating on neodymium’s quasi-four-level transition at a wavelength of 946 nm. Two modes of operation are described: a high-power multi-mode monolithic cavity generating 105 for 210 W of incident pump power with a slope efficiency of ∼54%, and secondly, a high-radiance configuration employing an external stable resonator producing a maximum output power of 29.2 for 86.5 W of incident pump-power, with a slope efficiency of 33%. The output beam quality values of the external cavity were M² of 3.2 by 2.4, leading to a maximum radiance of 0.43 GW cm⁻² sr⁻¹.