单晶Ce冲击相变的分子动力学模拟

金属Ce在室温条件下当压力达到约0.7 GPa时会发生一阶相变,体积突变减小14%—17%,相变前后两相分别为γ-Ce和α-Ce,均为面心立方结构.实验中发现冲击波在Ce中传播,其波形存在明显的多波结构依次为γ-Ce弹性前驱波、γ-Ce塑性波、γ-Ce→α-Ce相变波.基于新发展的金属Ce的嵌入原子势,对单晶Ce的冲击相变行为进行了分子动力学模拟.模拟结果表明,在一定强度下,单晶Ce中的冲击波阵面分裂为多波结构,波形结构与加载晶向明显相关:在[001]和[011]晶向加载下表现为双波结构,依次为前驱波和相变波;在[111]晶向加载下波阵面分裂为弹性前驱波、γ-Ce塑性波、γ→α相变波,与已有的实验观察相一致.冲击波速的Hugoniot关系在低强度加载下与实验符合得较好.同时在此冲击相变过程中,应力偏量对相变起促进作用,相较于静水压加载,冲击加载的相变压力条件更低一些.     

单晶铁沿[101]晶向冲击过程中面心立方相的形成机制

铁的冲击相变过程是科研工作者们关注的热点领域之一.铁沿[100]晶向冲击时会发生体心立方相到密排六方相的转变;而沿[101]晶向冲击时,相变产物除了密排六方相之外还出现一定量的面心立方相.人们已经明确了体心立方到密排六方相的转变机制,然而对于面心立方相的形成机制问题至今还在探索.本文通过分子动力学方法模拟了体心立方单晶铁沿[101]晶向的冲击过程,模拟结果显示体心立方相将转变为高压密排结构(密排六方相和面心立方相);并分析了面心立方相的形成机制:在冲击过程中,单晶铁沿[101]和101]晶向突然收缩,同时沿[010]晶向突然扩张,从而导致体心立方到面心立方相的转变.此外,本文进一步研究了不同应力状态下单晶铁的相变机制,发现沿[101]晶向单轴压缩以及沿[101]和[101]晶向双轴压缩时铁将发生体心立方到面心立方相的转变;而沿[101]和[010]晶向双轴以及三轴压缩时将会发生体心立方到密排六方相的转变.最后进一步计算了三个相的吉布斯自由能随压力的变化,并对冲击模拟结果进行了能量分析,给出了沿[101]晶向冲击条件下高压密排相产生的原因.     

非静水压条件下铁从α到ε结构相变的第一性原理计算

采用基于密度泛函理论的平面波赝势方法,研究了三轴加载的非静水压力和静水压力对铁从体心立方结构(bcc,α相)到六角密排结构(hcp,ε相)相变压力和磁性的影响,结果发现:在0-18 GPa压力范围内,相对静水压力条件,随着压力的升高,bcc结构的原子磁矩在非静水压力下降低得更快;在非静水压力下,相变更容易发生,相变压力随着非静水压力程度的增加而降低;并且对非静水压力对相变压力影响的物理机理进行了讨论.     

非静水压条件下铁从α到ε结构相变的第一性原理计算

采用基于密度泛函理论的平面波赝势方法,研究了三轴加载的非静水压力和静水压力对铁从体心立方结构（bcc,α相）到六角密排结构（hcp,ε相）相变压力和磁性的影响,结果发现：在0—18 GPa压力范围内,相对静水压力条件,随着压力的升高,bcc结构的原子磁矩在非静水压力下降低得更快;在非静水压力下,相变更容易发生,相变压力随着非静水压力程度的增加而降低;并且对非静水压力对相变压力影响的物理机理进行了讨论. 关键词： 相变 非静水压力 第一性原理 铁     

铁的冲击相变机制的分子动力学研究

 用分子动力学方法模拟计算了在冲击波加载条件下，单晶铁中的结构相变（由体心立方结构α相到六角密排结构ε相），相互作用势采用铁的嵌入式原子势（EAM），单晶铁样品的尺寸为28.7 nm×22.9 nm×22.9 nm，总原子数为1.28×10⁶个。通过推动一个运动活塞对静止靶的作用来产生冲击压缩，加载方向沿单晶铁的[100]晶向。通过对原子位置的追踪，揭示了铁的冲击相变机制，计算结果表明相变机制包括两步：首先是在{011}面上的原子受到沿〈100〉晶向的压缩，使{011}面转化成正六角形密排面；然后是在{011}面上原子沿〈0-11〉晶向的滑移，完成由bcc结构到hcp结构的相变。同时发现滑移面只出现在与冲击波加载方向平行的(011)和(0-11)面上。     

铁冲击相变的晶向效应

采用基于火炮加载的三样品精细波剖面对比测量,研究了晶向效应对铁弹-塑性转变及体心立方结构(bcc,α相)至六角密排结构(hcp,ε相)相变特性的影响.观测到单晶铁异常的弹-塑性转变行为,这与基于位错密度描述的黏塑性本构模型计算结果相符,对应的Hugoniot弹性极限δ_(HEL)均大于6 GPa,且具有晶向相关性,即δ(111)/(HEL)δ(110)/(HEL)δ(100)/(HEL);系统获取了相变起始压力P_(PT)晶向相关性的实验数据,[100],[110]和[111]晶向的PPT实测值分别为13.89±0.57 GPa,14.53±0.53 GPa,16.05±0.67 GPa,其变化规律与非平衡分子动力学计算结果相符.上述结果揭示出冲击压缩下单晶铁存在塑性与相变微观机理的强耦合,为完善用于冲击实验描述的相场动力学模型提供了重要的实验支撑.     

Fe40Ni40P12B8非晶合金的冲击晶化实验研究

 本文研究了Fe₄₀Ni₄₀P₁₂B₈非晶合金冲击波加载下的晶化行为，冲击波由二级轻气炮发射的告诉弹丸撞击靶产生。实验结果表明：Fe₄₀Ni₄₀P₁₂B₈非晶合金在冲击波加载下，晶化可在加载时间（微秒量级）内发生；晶化的阈值压力在30~50 GPa之间，相应的冲击温度约为510~800 K，晶化析出相与冲击压力有关，低压下析出相是面心立方γ-(Fe, Ni)固溶体和Fe₃(P_0.37B_0.63)化合物，高压下（大于60 GPa）析出相除了面心立方γ-(Fe, Ni)固溶体和Fe₃(P_0.37B_0.63)化合物之外，还包括(Fe, Ni)₃P化合物。     

准静水压条件下SrF2的X射线衍射

利用同步辐射能量色散X射线衍射技术对SrF₂进行了高压相变实验研究. 实验以Ar作为传压介质, 以获得准静水压条件. 实验用红宝石荧光法标定样品压力, 得到的最高压力为44.2GPa. 在实验压力范围内, SrF₂在11.2GPa时发生了从立方晶系到正交晶系的相变, 通过拟合相变前后的P-V状态 方程, 得到立方SrF₂的体弹模量为70.0(5.0)GPa, 正交SrF₂的体弹模量为198.3(15.2)GPa. 卸压到零压时, SrF₂回到立方相结构.     

ZnSe相变、电子结构的第一性原理计算

基于第一性原理平面波赝势(PWP)和广义梯度近似(GGA)方法,对闪锌矿结构(ZB)和岩盐结构(RS)的ZnSe在0—20GPa高压下的几何结构、态密度、能带结构进行了计算研究,分析了闪锌矿结构ZnSe和岩盐结构ZnSe的几何结构.在此基础上,研究了ZnSe的结构相变、弹性常数、成键情况以及相变压强下电子结构的变化机理.结果发现:通过焓相等原理得到的ZB相到RS相的相变压强为15.3GPa,而由弹性常数判据得到的相变压强为11.52GPa,但在9.5GPa左右并没有发现简单立方相的出现;在结构相变过程中,sp3轨道杂化现象并未消除,Zn原子的4s电子在RS相ZnSe的导电性中起主要贡献.     

纳米多晶铁的冲击相变研究

利用分子动力学方法研究了不同晶粒度的纳米多晶铁在冲击压缩下的结构相变过程,模拟结果表明:纳米多晶铁的冲击结构相变(由体心立方(bcc)结构 α 相到六角密排(hcp)结构 ε 相)发生的临界冲击应力在15 GPa左右.纳米多晶铁在经过弹性压缩变形后,晶界导致的塑性变形开始发生,然后大多数相变从晶界成核并最终发展为大规模相变.不同变形过程在应力和粒子速度剖面上能得到清晰的体现,并通过微观原子结构分析分辨.冲击压缩后的微观结构以晶界原子和以fcc结构原子充当孪晶界的hcp原子为主.晶粒度明显影响晶界变形及相变 关键词： 冲击相变 纳米多晶铁 冲击波 分子动力学     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.