Effect of Interaction upon Translocation of Confined Polymer Chain Through Nanopore

运用二维的键长涨落模型和蒙特卡洛方法研究高分子链从一个受限空间到自由空间穿孔过程中,链单体与纳米孔之间的相互作用.结果表明,在不同的链长和纳米孔交互作用下,高分子链成功穿越自由能能垒取决于链长和纳米孔长度,并且由于交互作用降低了自由能能垒,导致高分子链在纳米管的平均捕获时间缩短.     

打结高分子链穿孔行为的研究

以三叶草型结(即3₁结)为例,采用分子动力学(MD)方法,研究打结高分子链在外场力作用下穿越微孔的动力学过程.模拟发现,在拉动打结高分子链的过程中,结的大小呈涨落变化,直至最后散结.定性讨论了结的存在对高分子链穿孔速率的影响.在外场力作用下,打结高分子链平均穿孔时间(τ)与链长(N)满足标度关系τ～N ^α,其中标度系数α随外场力f增大而增大.对于短链,外场力越大,平均穿孔时间越短     

Translocation of Polymer Chains Through a Channel with Complex Geometries

采用nPERMis (new pruned-enriched rosenbluth method with importance sampling) 算法,研究了高分子链在通道中穿行的力学行为. 在管道穿行的过程中,计算了其作用力,发现进入中间通道的过程其对应的作用力f和第一个单体在x轴方向的位置关系曲线有一个平台(f>0). 由于高分子链的受限减少了高分子链的构象数目和熵,从而增加了其自由能, 因此只有在外力的作用下,高分子链才可以进入中间管道. 当高分子运动到某一位置后,第二个平台开始形成(f<0),这时高分子链自发进入右通道. 这是因为在右通道中高分子链的自由能降低的比左通道中高分子链的自由能升高的快. 右通道中的高分子链自发地拉动左通道中的高分子链. 研究了链长、左、右通道宽度对穿孔有很大影响. 通过这些研究可以详细解释各部分穿行时间不同的原因.     

Factors Affecting Polymer Translocation Through a Nanopore in a Membrane

采用Monte Carlo方法研究了高分子链穿越"trans"侧具有吸附作用的膜上纳米孔的过程. 当体系的温度TTc时,τ随着温度的升高而增大. 穿孔时间与膜的吸附势强度μ0 之间存在非单调依赖关系,τ首先随着μ0的增大而增大,最后τ随着μ0 的增大而减小. 研究穿孔时间与溶剂性质的关系时发现,当εAB<εc时,τ随着εAB 的增加而增加,当εAB>εc时,τ 随着"AB 的增加而减小. 高分子链穿孔时间与链长N之间存在着标度关系：当吸附势强度μ0>μc时,τ∝N^1.602,当μ0相似文献   

色关联的色噪声驱动的分段非线性模型的平均首次穿越时间

研究了色关联的乘性高斯色噪声和加性高斯色噪声驱动的分段非线性系统中, 噪声强度和相关时间对平均首次穿越时间的影响. 利用一致有色噪声近似方法和最速下降方法, 推导出系统平均首次穿越时间的表达式. 研究结果表明: 系统的平均首次穿越时间随着乘性噪声的增加会出现单峰结构, 即“共振”现象, 峰值会随着加性噪声强度和噪声之间关联强度的增加而减小. 而平均首次穿越时间作为加性噪声的函数呈单调曲线, 说明乘性噪声和加性噪声对平均首次穿越时间的影响不同. 此外, 乘性和加性噪声关联时间以及互关联时间在正关联时和负关联时 对系统平均首次穿越时间的影响是不同的. 关键词： 色噪声 分段非线性系统 平均首次穿越时间     

非关联噪声驱动的单稳系统的平均首次穿越时间

基于非对称双稳系统的理论研究了偏单稳系统的平均首次穿越时间问题,并基于势函数分析了参数对平均首次穿越时间的影响.得出结论:1)当偏稳系数为零时,随着加性噪声强度和参数a的增加,两个方向的平均首次穿越时间相等且均单调减小,2)随着偏稳系数b的增加,势阱的对称性被破坏,粒子由xs1跃迁到xs2的时间线性地减小,而粒子由xs2跃迁到xs1的时间线性地增加.3)随着乘性噪声强度和加性噪声强度比率R的增加,两个方向平均首次穿越时间均单调增加.     

紧密高分子链从无规线团到球形相变的蒙特卡洛模拟：链单体的相互作用

本文采用蒙特卡洛模拟研究紧密高分子单链的无规线团到球形转变过程. 首先,研究某一固定链单体的相互作用下的有效尺寸效应,并发现短链表现出一次的坍塌相变,而长链则出现两次,这从热熔曲线上可以明显看出. 随着链单体相互作用的减小,热熔曲线上峰值对应的转变温度朝着低温转移. 从体系的能量、均方回转半径和形状因子可以进一步看出,高分子相变发生在更低的温度区间. 这些结果有助于加深理解高分子坍塌相变过程中链单体相互作用的影响.     

高分子链移位动力学的理论和模拟研究

高分子链通过纳米管道或纳米孔的移位,存在于各种生命过程中,是物理、化学和生物领域的重要课题,在实验、理论和计算机模拟等领域已经被广泛研究,并应用于科技的不同领域。本文总结了高分子链移位的理论和模拟方面的最新研究成果,讨论了自由能形貌对高分子链移位动力学过程的影响。结合理论计算和模拟研究,分析了链与管道的相互作用、链的组分、链节电荷分布、管道的性质等因素对自由能形貌和高分子链移位时间的影响,并结合自由能形貌对研究结果进行了解释。研究结果有助于理解高分子链的移位机制,从而进一步调控高分子链的移位时间。     

外力驱动作用下高分子链在表面吸附性质的计算机模拟

采用退火法模拟研究受外力F驱动的高分子链在吸引表面的吸附特性.通过高分子链的平均表面接触数〈M〉与温度T之间的关系计算临界吸附温度T_c,并发现T_c随着F的增加而减小;进而通过高分子链的均方回转半径分析外力驱动作用对高分子链构象的影响,并从回转半径极小值或者垂直外力方向的y和z分量的变化交叉校验临界吸附点T_c.模拟计算了处于吸附状态的高分子链随着外力F的增加是否会发生吸附状态到脱附状态的相变以及发生相变所需施加的外力是否由温度所决定.模拟结果表明:两种不同温度下高分子链的吸附性质和构象性质受外力驱动作用而产生不同现象,在温度区间T*_cTT_c时会发生脱附现象,而在TT*_c时不会发生脱附现象.     

纳米通道内高分子稀溶液的分子动力学模拟

运用分子动力学方法对纳米通道内的高分子稀溶液进行了模拟,分析了通道宽度、壁面性质和链长对高分子链构象参数和质心密度分布的影响。模拟结果表明:随着通道宽度和壁面接触角的增大,回转半径逐渐减小,高分子链实现了从二维构象向三维构象的转变;通道宽度的减小和壁而接触角的增大,均导致高分子链远离壁面;在通道宽度一定时,长链高分子易呈伸展状且远离壁面,而短链易呈团聚状且移向壁面.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.