切趾技术对光纤布拉格光栅法布里-珀罗滤波器反射特性优化的研究

利用矩阵分析法,针对两个相同光栅构成的光纤布拉格光栅法布里-珀罗(F-P)腔滤波器进行理论分析。数值模拟分析了光栅长度变化对光栅以及F-P腔滤波器反射特性的影响,指出光栅长度增加对反射特性影响的优缺点,分析利用常用切趾函数对光栅进行切趾,减小由于光栅长度增加导致反射谱的的旁瓣增大,对组成的F-P腔滤波器的反射特性的优化,得到了光栅切趾对F-P腔滤波器的反射特性的影响规律。对于在实际应用中制作出性能优良的光纤布拉格光栅F-P腔滤波器有一定的参考价值。     

一种基于光纤光栅法布里-珀罗腔的低频振动传感器

提出了一种基于光纤光栅法布里-珀罗(F-P)腔的低频振动传感方案并进行了理论分析和实验研究。采用单频激光器作为光源,光纤光栅F-P腔通过两点涂胶方式粘接在等强度悬臂梁上,待测振动信号通过支架和悬臂梁将振动作用传至光纤光栅F-P腔,引起腔长周期性变化,从而改变光纤光栅F-P腔的反射光谱特性,通过解调输出光信号的振荡频率和峰值,即可实现对振动信号频率和幅值的测量。利用压电陶瓷模拟的低频振动信号进行了实验验证,测量结果与理论分析相吻合。该传感器测量灵敏度高,特别适用于微弱振动信号的测量。     

一种基于光纤光栅F-P腔的低频振动传感器

A sensor solution for weak vibration based on Fiber Bragg Grating Fabry-Perot (F-P) cavity is designed and experimentally demonstrated, in which a laser with single-frequency is used as the light source. The F-P cavity is affixed to the cantilever structure of even distribution of strain along the axis and the pair of fiber Bragg gratings as the cavity reflectors is placed freely. The vibration spreading to fiber grating F-P cavity through the cantilever beam vibration, causes changes in cavity length, thus changing the reflective light intensity of fiber grating F-P cavity. Theoretical Analysis indicates that, the amplitudes and frequencies of vibration can be measured by demodulating the peaks and frequencies of the signal. The experimental results of measuring artificial vibration simulated with PZT agree with the theory well. This sensor has high measuring accuracy and can be used for detecting weak vibration.     

光纤光栅法布里-珀罗传感器频分复用技术

理论分析了光纤光栅法布里-珀罗(F-P)传感器频分复用技术的原理,并给出了信号处理对腔长选取的要求。数值模拟结果表明,不同腔长的传感器具有不同的谐振条纹频率,为保证频域中的信号不发生重叠,要求不同光纤光栅法布里-珀罗传感器间的腔长之差必须大于光纤光栅的长度。进一步的实验及模拟分析结果发现,温度等待测量的变化仅仅使光纤光栅法布里-珀罗传感器的反射光谱整体平移,相应的频域信号只产生相移而形状不发生变化,因而不能采用普通光纤法布里-珀罗(FFP)传感器的腔长傅里叶变换解调法解调频分复用光纤光栅法布里-珀罗传感器的信号。根据这一特点,提出了利用自相关分析实现频分复用传感器系统信号解调的方案。     

双包层光纤光栅选频双包层光纤激光器

双包层光纤激光器中多采用法布里珀罗(F-P)线形腔结构,谐振腔为一只二向色镜和光纤端面菲涅耳反射镜(反射率约为4％)构成,这属于一种有缺陷的腔结构,其稳定性不好,产生激光的波长很难得到有效控制,后腔镜不能精确选择激光器的输出波长,激光器的输出谱线较宽。在某些对激光波长有明确要求的应用中,该结构会受到限制。采用布拉格光纤光栅作腔镜,利用其窄带滤波特性,可以得到窄线宽的激光输出,目前报道的作为腔镜的布拉格光纤光栅为在单包层光敏光纤上制作而成,然后分别将不同反射率的光纤光栅与双包层增益光纤熔接,这给腔镜与双包层光纤之间带来很大的耦合损耗,影响了激光器的功率输出。该文报道了用相位掩模法在双包层光纤芯上写入了布拉格光纤光栅,并把此光纤光栅做为后腔镜．对长度为10m、20m的D形掺Yb^3 双包层光纤激光器进行实验研究,在1058nm附近得到稳定的窄线宽激光输出,3dB带宽为0．329nm。激光器最大输出功率为570mW。最后对实验结果进行了理论分析。     

用于光纤布拉格光栅法布里-珀罗腔的改进的Rouard算法

比较了光纤布拉格光栅法布里一珀罗腔的极限法、平衡法及传输矩阵法3种算法,证明了它们是一致的,指出了光纤布拉格光栅复振幅传输矩阵的相移特性对法布里一珀罗腔透射率的影响.对计算任意折射率调制的光纤布拉格光栅的Rouard算法进行了改进,在分层方法中考虑了折射率分布初始相位的影响,获得了更为准确的反射复振幅相位特性,将该结果应用于计算光纤布拉格光栅法布里一珀罗腔,得到了光纤布拉格光栅法布里一珀罗腔具有多峰结构的透射谱,并经过实验验证了该理论的正确性.     

光纤布拉格光栅法布里-珀罗腔纵模特性研究

分析了光纤布拉格光栅构成的法布里-珀罗（F-P）腔的透射谱特性，讨论了光栅带宽，反射系数相位因子以及腔长对F-P腔透射特性的影响，并对F-P腔随温度和应变的特性进行了分析，然后给出如何设计在光栅中心耦合波长处单模运转的法布里-珀罗腔.并提供了数值模拟结果和实验结果. 关键词： 光纤布拉格光栅 法布里-珀罗（F-P）腔 光纤激光器     

Variable Wavelengths Fiber Bragg Gratings Written with A Phase Mask and Four Prisms

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｓｉｎｃｅｔｈｅｆｉｂｅｒｗａｓｐｌａｃｅｄｄｉｒｅｃｔｌｙｂｅｈｉｎｄｔｈｅ ｐｈａｓｅｍａｓｋ ,ｗｈｉｃｈｗａｓｏｒｉｇｉｎａｌｌｙｄｅｍｏｎｓｔｒａｔｅｄｂｙＫ .Ｏ .Ｈｉｌｌｅｔａｌ.ｉｎ 1 993[1] ,ｔｈｉｓｍｅｔｈｏｄｈａｓｂｅｅｎｕｓｅｄｗｉｄｅｌｙｆｏｒｗｒｉｔｉｎｇｆｉｂｅｒＢｒａｇｇ ｇｒａｔｉｎｇ .Ｈｏｗｅｖｅｒ ,ｔｈｅｃｏｎｔａｃｔｔｅｃｈｎｉｑｕｅｏｆｐｈａｓｅｍａｓｋｃａｎｏｎｌｙｉｎｓｃｒｉｂｅｔｈｅｆｉｂｅｒＢｒａｇｇ ｇｒａｔｉｎｇｗｉｔｈ…     

光纤布拉格光栅及其构成的法布里-珀罗腔的相位谱特性研究

光纤光栅的相位谱对光纤光栅法布里-珀罗(F-P)腔的光谱特性有重要影响.对光纤布拉格光栅(FBG)光谱,特别是FBG相位谱进行了深人分析,推导了低反射率FBG的线性相位谱的一般表达式,提出了高反射率FBG的三段线性相位近似方法,得到了简洁直观的相位谱数学表达式.然后采用和普通F-P腔对比的方式,以等效腔长的概念分析了F...     

用于单频光纤激光器的光纤光栅双腔Fabry-Perot结构传输谱特性理论研究

分析了基于光纤光栅的全光纤型双腔Fabry-Perot(F-P)结构传输谱特性. 理论推出了两腔F-P结构传输率具体计算公式,给出在光栅中心波长处产生单谐振传输峰时,腔长与组成光栅反射率各需满足的条件. 基于理论分析结果,分两部分数值模拟了对称及非对称两腔F-P结构传输谱,讨论了计算结果并给出定性的解释,总结了腔长及光栅长度、折射率调制深度的设计原则. 结论表明,当单腔F-P结构腔长增大到阻带内出现多个谐振峰时,通过合理选取两腔结构的腔长及光栅参数,双腔F-P结构能够在整体长度不变条件下,抑制中心波长两侧的次谐振峰,而中心波长处的主谐振峰不受影响. 关键词： 光纤光栅 Fabry-Perot结构 光纤激光器     

Fiber Bragg grating and its application in external cavity semiconductor laser

The FBG-ECL fabricated using the interactions of laser diodes with fiber Bragg gratings has important role in optical communications. In this paper the comparison analysis of fiber Bragg grating and it's application in FBG-ECL are described in detail. The important parameters such as the bandwidth, SMSR and optimal output power of the FBG-ECL were analyzed deeply in the paper. The influence of the two important parameters (the residual reflectivity and external cavity length) on the FBG-ECL characteristic was given.     

Asymmetrically Apodized Fiber Bragg Gratings for Applications in Dispersion-Less Fabry-Pérot Fiber Cavities

Abstract

This article presents a theoretical study of the dispersion properties of the asymmetrically apodized fiber Bragg gratings. It is shown that the dispersive behavior of these gratings may be changed from normal to anomalous, depending on the apodization function and the grating strength. The asymmetrical Bessel functions were chosen in order to demonstrate these properties of the gratings. The application of this effect in a dispersion-less Fabry-Pérot fiber cavity formed by two asymmetrically apodized fiber Bragg gratings is discussed.     

Multi-point, fiber-optic gas detection with intra-cavity spectroscopy

A novel intra-cavity fiber laser system is demonstrated for multi-point gas detection. The laser uses fiber Bragg gratings as wavelength-selective cavity mirrors and a tunable filter to tune the operating wavelength to the Bragg wavelength of a selected Bragg grating. The Bragg wavelengths of the gratings are chosen to be aligned to different absorption lines of a gas or gases, allowing gas concentrations at multiple locations to be determined.     

光纤光栅法布里-珀罗腔的V-I传输矩阵法研究

快速有效地获得多级联光纤光栅法布里-珀罗(F-P)腔的光谱特性,是优化设计基于上述结构建立的级联多波长激光器、放大器等各种光器件以及复杂分布式传感网络的重要基础和保障.将V-I传输矩阵法用于光纤光栅F-P腔反射光谱特性的分析,并建立了V-I传输矩阵模型.采用该模型对三种不同结构的光纤光栅F-P腔在不同参数下的光谱特性进行分析,并与传统多层膜法的分析结果相比较,表明V-I传输矩阵法能够在保证分析精度的前提下大大节省运算时间.实验结果表明,V-I传输矩阵法对光纤光栅F-P腔谱特性的分析结果比耦合模法更准确.     

73-nm tuning of a double-clad Yb<Superscript>3+</Superscript>-doped fiber laser based on a hybrid array

We report on a wide wavelength tuning in a double-clad ytterbium-doped fiber laser. The laser cavity consists of an array of broadband high-reflection fiber Bragg gratings and a bulk grating as the output coupler and wavelength selection element. The proposed fiber laser configuration combines a low intracavity loss of the fiber Bragg grating mirrors with a wide wavelength tuning of the bulk gratings. We demonstrate a >70-nm wavelength tuning range, limited only by the available fiber Bragg gratings.     

聚合物封装的高灵敏度光纤光栅温度传感器及其低温特性

介绍了一种新型的光纤光栅温度传感器。这种光纤光栅温度传感器使用了特殊的工艺将光纤布拉格光栅封装于一种热膨胀系数较大的有机聚合物基底中 ,使得传感器的温度灵敏性比裸光纤光栅提高了 12 .3倍 ,其温度灵敏度系数KT 达到 82 .6 9× 10 -6/℃。在 - 80～ 0℃的低温度范围内 ,对这种新型光纤光栅温度传感器的反射谱进行了测量。研究了这种新型光纤光栅温度传感器的低温特性 ,并与裸光纤光栅和铝基封装的光纤光栅进行了比较 ,结果表明这种新型的光纤光栅温度传感器具有很好的低温响应特性。     

极窄带宽的布拉格光纤光栅光谱特性研究

根据理想模展开下的耦合模方程，对光纤布拉格光栅的峰值反射率公式进行了数学推导，得到了布拉格光纤光栅的光谱反射率表达式。全面讨论了光栅周期、光纤栅长、光致折射率微扰最大值等参数与光纤光栅反射光谱的关系。仿真结果显示了固定参数下布拉格光栅的极限窄带宽，得到的反射率为1、带宽为0.02nm的窄带宽布拉格光栅，比现今分布式传感系统中使用的布拉格光栅的带宽窄1个数量级。这种布拉格光纤光栅用于分布式传感系统，可大大提高分布式传感系统中光源的带宽利用率，消除各信号间的相互串扰，提高传感光栅复用数目，降低解调系统成本。     

Variable Wavelengths Fiber Bragg Gratings Written with A Phase Mask and Four Prisms

Using only one diffractive element, the Talbot interferometer provides a robust and inherently stable method for reproducing fiber Bragg gratings with variable wavelengths, and reduces the complexity of the fiber grating fabrication system. However, the usable length of the grating is limited by the practical length of the mirrors. This paper presents a phase mask with two fixed prisms and two rotational prisms to inscribe fiber Bragg gratings with variable Bragg wavelengths. In this system, the fiber Bragg grating is inscribed by UV interference stripes of 193 nm derived from two rotational prisms and two fixed prisms, where phase mask is used as a beam splitter of ±1 order diffraction light. It is noteworthy that the tunable phase mask interferometer decreases the demand of the length of prism evidently.     

Single-longitudinal-mode fiber ring laser using fiber grating-based Fabry-Perot filters and variable saturable absorbers

A single-longitudinal-mode (SLM) fiber ring laser is demonstrated by incorporating a fiber Bragg grating (FBG)-based Fabry-Perot (F-P) filter and a variable saturable absorber in a fiber ring cavity. An ultra-narrow bandpass filter is established by the combined mode filtering of the FBG-based F-P filter and the variable saturable absorber. No accurate control for cavity length is required, and stable single longitudinal-mode operation without mode hopping is conveniently achieved.     

对光纤布拉格光栅法布里-珀罗腔纵模间隔问题的研究

对光纤布拉格光栅(FBG)法布里-珀罗(F-P)腔的透射特性进行了深入分析,指出了FBG F-P腔透射谱中纵模位置的影响因素,讨论了与普通F-P腔的联系和区别.应用光栅的有效镜面模型对FBG反射主瓣内反射系数的相位因子进行线性模拟,定义了FBG有效长度的概念并得出其表达式.提出将FBG的有效长度纳入到FBG F-P腔的等效腔长中,用等效腔长来计算FBG F-P腔中的纵模间隔.数值仿真和实验结果都表明,用等效腔长计算所得的纵模间隔与实际的FBG F-P腔中的纵模间隔符合很好,误差极小. 关键词： 光纤布拉格光栅 法布里-珀罗腔 纵模间隔 有效镜面模型