分段式电子回旋波驱动电流对早期新经典撕裂模的抑制

新经典撕裂模的产生会严重影响托卡马克装置的约束性能，而且在高参数运行状态下的所有装置中该不稳定性不可避免。新经典撕裂模的抑制工作对于聚变装置至关重要，电子回旋波驱动电流(ECCD)是目前抑制新经典撕裂模的主要手段之一。用数值模拟的方法研究了在新经典撕裂模发展的早期加入ECCD后，对新经典撕裂模发展的影响。通过数值模拟发现较小份额的连续ECCD可以减小新经典撕裂模早期的增长速度，同时可以提高再次加入电子回旋波驱动电流抑制处于增长期的新经典撕裂模的效率。     

斜变法在HL-2A电子回旋加热功率沉积计算中的应用

介绍了用斜变法计算等离子体在辅助加热中能量沉积剖面的基本原理,并首次在HL-2A上利用斜变法处理在电子回旋波注入时刻电子的温度密度等参数数据,得出了电子回旋在轴加热和离轴加热的功率沉积剖面,验证了该方法的适用性.     

EAST װ��ECRH ϵͳ���߲������Ż�����

利用TORAY程序对电子回旋波的传播轨迹、功率沉积和电流驱动等参数与波束发射位置、发射角度的相互关系进行了数值模拟计算,给出了天线的最佳发射位置和天线平面反射镜在极向和环向转动角度的调节范围,分析了不同入射角对微波功率沉积及驱动电流的影响。     

HL-2Aװ�õ��ӻ���������Ȳ����͹��ʳ�������ķ�������

在HL-2A单零偏滤器条件下,对由弱场侧沿赤道平面垂直注入的电子回旋寻常波(O-模)的波迹和波的功率沉积剖面进行了分析计算。对近磁轴共振情形,需要确定一个有效的物理尺度以正确获得波功率沉积。单一波束的有效吸收层的厚度可以合理地作为这一物理尺度,从而获得统一的功率沉积公式。对比研究了磁轴偏离赤道面和位于赤道面情况下的波功率沉积剖面。     

“A=2托卡马克堆芯等离子体基本特性研究”2006年进展

主要涉及两方面的研究内容：第一是托卡马克等离子体的磁流体气球模稳定性研究；第二是HL-2A装置电子回旋加热有关的基础理论问题。包括三方面研究成果：（1）简要报道了关于负剪切区电阻气球模不稳定性及本征函数特性，给出了增长率与等离子体参数的定标关系；（2）利用Solov’ev位形中严格的气球模方程，讨论了应用广泛的s，α平衡模型的正确性；（3）计算分析了由弱磁场侧垂直入射的电子回旋波寻常模在HL-2A等离子体中的功率沉积剖面。     

发射波功率密度对电子回旋波电流驱动的影响

采用高斯光束的研究方法,结合Fokker-Planck方程,在堆级等离子体条件下模拟了发射波功率密度的改变对电子回旋波功率沉积以及电流驱动的影响。结果表明,高功率密度的波束会拓宽功率沉积剖面,使功率沉积的位置略有外移,电流驱动效率略有降低。     

���䲨�����ܶȶԵ��ӻ���������������Ӱ��

采用高斯光束的研究方法,结合Fokker-Planck方程,在堆级等离子体条件下模拟了发射波功率密度的改变对电子回旋波功率沉积以及电流驱动的影响。结果表明,高功率密度的波束会拓宽功率沉积剖面,使功率沉积的位置略有外移,电流驱动效率略有降低。     

托卡马克等离子体不同平衡位形下的电子回旋波电流驱动

在给定的等离子体总电流和中心电流密度条件下,数值求解平衡方程,求出不同拉长比和三角形变因子的托卡马克等离子体温度、密度、磁场分布,然后通过求解波迹方程和Fokker-Planck方程,分别计算这些位形下的电子回旋波波迹和电流驱动.结果表明：电子回旋波X模从顶部发射时,随着拉长比的增大,波迹会向弱场侧偏移.电子回旋波X模从弱场侧发射时,电子回旋波在等离子体中传播沉积的功率份额随着拉长比的增大而增加,驱动电流位置随着三角形变因子的增大向等离子体中心移动.驱动电流位置随环向和极向发射角的减小向中心移动,对应的电流密度峰值也变大.     

CFETR稳态运行模式的0.5维集成模拟及其杂质粒子比例影响的分析

采用快速集成模拟软件METIS完成了CFETR1GW稳态反剪切运行模式的设计。该反剪切运行模式由40MW离轴电子回旋电流驱动(ECCD)与60MW的离轴中性束电流驱动(NBCD)所实现，获得了稳定的安全因子剖面，其在ρ=0.52处具有最小安全因子q_min=3.1，从而可避免危险的m/n=2/1、3/2、5/3的新经典撕裂模(NTM)。此外，本文还分析了Ar杂质粒子的含量对此稳态反剪切模式约束性能的影响。     

磁镜等离子体中电子回旋波加热实验的理论研究

本文利用平行平板模型,给出了在不同位置、以不同角度入射到平衡的磁镜等离子体中电子回旋波的传播轨迹;利用线性理论计算了O,X波能量分别被本底电子、热电子吸收的波能量沉积率。根据计算结果,文中对加热本底等离子体的特征进行了描述,对非封闭热电子环的形成作了初步解释。     

˺��ģʵʱ��������ϵͳ

Tearing mode real-time active control system has been developed on HL-2A tokamak. During the plasma discharge, electron cyclotron emission and soft X-ray diagnostic signals are used to get the geometric location where tearing modes emerge, combined with the real time profile reconstruction and electron cyclotron wave (ECW) deposition algorithm, the target angle of ECW steering mirror can be obtained. Then the mirror angle is set by the motor so that the ECW power deposit at the position of tearing modes finally. Consequently the tearing modes can be controlled, owing to the change of local current profile, and the plasma confinement is improved. This system has been deployed in HL-2A campaigns after 2015, and the good control effect is obtained. It has been proved that the system can discover and control not only the classical tearing modes in real time, but also has the potential to control the neoclassical tearing mode in the future.     

Neoclassical tearing mode stabilization by electron cyclotron current drive for HL-2M tokamak

Investigation of neoclassical tearing mode and its suppression by electron cyclotron current drive(ECCD) has been carried out in HL-2 M tokamak. The current driving capability of the electron cyclotron wave is evaluated. It is found that the deposition location can be effectively controlled by changing the poloidal angle. The validation of electron cyclotron wave heating and current driving has been demonstrated for the upper launcher port. We show that 3.0 MW and2.5 MW modulated ECCD can completely stabilize(2,1) and(3,2) NTMs, respectively. The non-modulated ECCD, radial misalignment as well as current profile broadening have deleterious effect on the NTM stabilization. The time required for suppression of(3,2) mode is shorter than that required for the suppression of(2,1) mode. Moreover, the time needed for complete stabilization at different initial island width has been quantitatively presented and analyzed.     

用电子迴旋共振加热抑制托卡马克中的撕裂模

利用电子迴旋共振加热的定域性,改善等离子体电流分布,从而改善撕裂模的稳定条件,只要电子迴旋共振加热的吸收区能覆盖住撕裂模的共振层,就有很好的稳定效应;而不一定要求电子迴旋共振面与撕裂模的共振面重合,在迴旋加热期间,撕裂模被有效地抑制住。 关键词：     

First Observation of Neoclassical Tearing Modes in the HL-2A Tokamak

The m/n = 2/1 neoclassical tearing modes are first observed in HL-2A low density, low beta plasma with central electron cyclotron resonance heating. The neoclassical tearing modes （NTMs） are triggered by a sawtooth crash with m/n = 1/1 precursors, which are toroidal coupled with a small scale m/n = 2/1 mode. The time history of the island width is compared with the prediction of the NTM theory, showing a good agreement between theory and experiment.     

Numerical analysis of the optimized performance of the electron cyclotron wave system in a HL-2M tokamak

The capabilities of current drive, neoclassical tearing mode(NTM) stabilization, and sawtooth control are analyzed for the electron–cyclotron wave(ECW) system in a HL-2M tokamak. Better performance of the upper launcher is demonstrated in comparison with that of a dropped upper launcher, in terms of J_(EC)/J_(bs) for NTM stabilization and I_(ECCD)/(?ρtor)~2 for sawtooth control. 1-MW ECW power is enough for the 3/2 NTM stabilization, and 1.8-MW ECW power is required to suppress 2/1 NTM in a single null divertor equilibrium with 1.2-MA toroidal current with the upper launcher. Optimization simulation of electron–cyclotron current drive(ECCD) is carried out for three mirrors in an equatorial port, indicating that the middle mirror has a good performance compared with the top and bottom mirrors. The results for balanced co- and counter-ECCD in an equatorial port are also presented.     

EAST 电子回旋共振加热效果的数值模拟和分析

为了给EAST 电子回旋共振加热物理实验提供理论依据和模拟预测,从电子热输运方程出发,运用 CRONOS 输运程序对不同等离子体和波参数下,电子回旋加热效果进行了数值模拟计算。给出不同电子回旋波功率、入射角、电子密度和纵场等参数对电子回旋加热效果的影响,预测在不同参数下,电子温度、等离子体总内能和能量约束时间的变化,分析了其原因,并与实验结果进行了初步的比较。     

�п�����е��ӻ���������Ӳ�Эͬ���������ĸ�ЧӦ����

The synergy current drive by combining electron cyclotron wave (ECW) with lower hybrid wave (LHW) can be used to either increase the noninductive current drive efficiency or shape the plasma current profile. In this paper, the synergy current drive by ECW and LHW is studied with numerical simulation. The nonlinear relationship between the wave powers and the synergy current of ECW and LHW is revealed. When the LHW power is small, the synergy current reduces as the ECW power increases, and the synergy current is even reduced to lower than zero, which is referred as negative synergy in the this context. Research shows that the mechanism of the negative synergy is the peaking effect of LHW power profile and the trapped electrons effect. The present research is helpful for understanding the physics of synergy between electron cyclotron current drive and lower hybrid current drive, it can also instruct the design of experiments.     

A New Criterion for Disruption Prediction on HL-2A

A new criterion has been proposed to predict the major disruptions caused by tearing mode instabilities. According to the HL-2A experimental results, the statistical analyses are employed to investigate the relationships between MHD activities and the plasma disruptions. Two kinds of the tearing mode activities can finally cause the disruption on HL-2A operations. By introducing a new parameter, i.e. an integral of poloidal magnetic field over time, as the criterion of disruption precursor, almost all of the disruptions can be predicted.     

HL-2A装置等离子体可见光成像系统

在HL-2A装置上研制了等离子体可见光成像系统,用于孔栏、偏滤器位形放电的诊断。该成像系统由彩色摄像机、观察窗和转向镜、广角收集和准直透镜组、采集卡和计算机组成。本文描述了系统的布局和各部件参数的匹配,报道了观测到的实验结果。等离子体成像系统能监视放电的整个过程,实时显示可见光辐射图形,特别在识别孔栏与偏滤器位形放电的诊断中发挥了重要作用,成为HL-2A装置放电的重要诊断手段。     

Design of the Upgraded TJ-II Quasi-optical Transmission Line

TJ-II plasma start-up and heating are made by electron cyclotron resonance waves at the second harmonic of the electron cyclotron frequency. Two quasi-optical transmission lines transmit the microwave power of the gyrotrons to the vacuum vessel. The first line launches the microwave power under fixed injection geometry, i.e. there is no possibility to change the launching angle and the wave polarization. The second line has a moveable mirror installed inside the TJ-II vessel. To get high absorption efficiency and a narrow energy deposition profile the internal mirror focuses the wave beam at plasma center.To get more flexibility in the experiments on heating and current drive the first transmission line needs to be upgraded. The design is presented in this paper. The new launching antenna includes an internal mirror to focus the beam and to change the injection angle. Both launchers are then symmetrical. A polarizer consisting of two corrugated mirrors is used to get any wave polarization. Two mirrors with an array of coupling holes and calorimetric measurements of the energy absorbed in the barrier window allow the estimation of the microwave power launched into the TJ-II.