螺栓紧固型纵振换能器设计考虑

本文采用网络传输法分析了螺栓紧固型纵振换能器的设计方法，并考虑了换能器结构件的内部机械损耗和压电元件的电损耗，数值计算了换能器谐振特性及书面位置，结果与实验情况一致。     

背衬参数对厚度模压电换能器特性的影响

系统研究了厚度模压电换能器的背衬厚度、声阻抗率及机械损耗因子对换能器振动性能影响,重点分析了在所关心频率附近的有效机电耦合系数和机械品质因数。计算结果表明,随着背衬厚度增大,换能器的有效机电耦合系数和机械品质因数均震荡减小;背衬声阻抗率与压电片声阻抗率差值增大,换能器有效机电耦合系数减小,机械品质因数增大;保持压电片厚度不变,增大背衬的机械损耗因子,换能器有效机电耦合系数单调减小,机械品质因数有极小值,在给定频率范围内电特性曲线趋于光滑。用有限元方法验证了等效电路计算方法的正确性,并对比了换能器的测试结果和计算结果。计算所得规律为厚度模压电换能器的设计和实验制作提供了理论依据。      

大尺寸夹心式压电超声换能器的设计

现有的夹心式压电超声换能器的设计方法多从一维理论出发，它对横向尺寸较大的换能器并不适用．本文研究了大尺寸夹心换能错的铝合振动，通过引人振动体的等效弹性系数，推出了换能器的耦合振动频率方程，并给出了换能器纵向共振频率的设计准则．与数值法相比，本方法计算非常简单．与一维理论的计算结果相比，利用本文理论得出的换能器的纵向共报频率与实测值更加符合．     

圆锥面PVDF聚焦换能器的非线性声场理论及实验研究

圆锥面聚焦换能器可在超声成像中获得较好径向分辨率的同时提高探测深度.利用高斯声源函数叠加法来近似表示圆锥面聚焦声源的分布函数，结合近轴近似的KZK方程，得到了圆锥面聚焦换能器在损耗媒质中产生的基波、二次谐波声场的解析解.在实验上制作了PVDF圆锥面聚焦换能器，测量了圆锥面聚焦换能器的基波及二次谐波声场，实验结果和理论计算相符.     

水声换能器研究新进展

文章综述了几种典型结构水声换能器近些年的新发展,包括:弯张换能器、圆柱面辐射型换能器、纵向换能器等等,主要介绍这些结构类型水声换能器的设计新思想和多方面优化改进的新成果。     

夹心复合材料宽带超声换能器的研制

本文采用高频夹心PZT(3-3)复合材料、单层前匹配和高损耗声阻抗背村全匹配的结构,研制出窄脉冲宽带超声换能器.所研制的中心频率为1MHz的换能器,在水负载中有高传输效率,得到声压脉冲长仅一个周期的接收波形.对铝合金和灰岩等较低声阻抗负载,也得到了一个周期脉冲的接收波形.     

高频空气声换能器研究现状与展望

本首先阐述高频空气声换能器的设计要点，然后介绍空气声换能器在测距、成象、材料特性无损评价等方面的初步应用，最后讨论空气声换能器进一步研究的发展方向及应用前景。     

一种纵扭复合换能器型超声马达的原理及实验研究

本文从纵扭振动换能器理论出发，计算了一种新的复合换能器型超声马达，并进行了实验研究，测出了其主要性能参数。     

多分量超声波换能器及其应用

为提高超声无损检测的精度的可靠性，本文研究了几种多分量超声波换能器，即二分量换能器和三分量换能器，分析和探讨了它们在声发射检测以及超声法应力测试中的应用。     

对2-2型压电复合材料横波换能器产生的纵波特性的研究

在固体测量中，横波换能器所产生的波列中常伴随有纵波，认识纵波产生的原因可以解释横波测试中出现的现象，以及抑制纵波提供有效的方法，本文利用实验研究的方法，用一对纵波偶极子换能器的对比实验，分析了２－２型压电复合材料厚度切变换能器产生纵波的机理，发现这是一种伴随着晶片厚度切变振动而产生的“偶极子”纵波，并由此解释了这种纵波的伴随性，频率特性及其首波与横波首波位相相反等问题。     

Micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular array

This paper reports the design, fabrication, and performance of miniature micromachined high frequency PMN-PT/epoxy 1-3 composite ultrasonic annular arrays. The PMN-PT single crystal 1-3 composites were made with micromachining techniques. The area of a single crystal pillar was 9 × 9 μm. The width of the kerf among pillars was ∼5 μm and the kerfs were filled with a polymer. The composite thickness was 25 μm. A six-element annular transducer of equal element area of 0.2 mm² with 16 μm kerf widths between annuli was produced. The aperture size the array transducer is about 1.5 mm in diameter. A novel electrical interconnection strategy for high density array elements was implemented. After the transducer was attached to the electric connection board and packaged, the array transducer was tested in a pulse/echo arrangement, whereby the center frequency, bandwidth, two-way insertion loss (IL), and cross talk between adjacent elements were measured for each annulus. The center frequency was 50 MHz and −6 dB bandwidth was 90%. The average insertion loss was 19.5 dB at 50 MHz and the crosstalk between adjacent elements was about −35 dB. The micromachining techniques described in this paper are promising for the fabrication of other types of high frequency transducers, e.g. 1D and 2D arrays.     

Optimization of the performance of the sandwich piezoelectric ultrasonic transducer

The resonance and antiresonance frequency, the effective electromechanical coupling coefficient, and the mechanical quality factor of a sandwich piezoelectric ultrasonic transducer are studied and optimized. The effect of the thickness of thick piezoelectric element electrodes on the transducer performance is analyzed. The effect of the length and position of the piezoelectric elements in the transducer is also studied. It is shown that, although using thick electrodes is beneficial for releasing heat produced by the piezoelectric elements, the effective electromechanical coupling coefficient and the mechanical quality factor are reduced. The length and the position of the piezoelectric elements affect the performances of the transducer. Increasing the length of the piezoelectric elements decreases the mechanical quality factor, but the effective electromechanical coupling coefficient increases. When the length reaches a certain value, the effective electromechanical coupling coefficient reaches a maximum value. When the piezoelectric elements are located at the geometrical center or the displacement node, the effective electromechanical coupling coefficient and the mechanical quality factor are maximized.     

Study of 1-3-2 type piezoelectric composite transducer array

Based on a new structure of precise location and decoupling between the transducer elements, high frequency underwater transmission transducer arrays with 4 elements and 8 elements serried uniform linear array were studied, using novel 1-3-2 type piezoelectric composite as the sensing material. There are ceramic framework supports in the transverse and longitudinal directions in 1-3-2 type piezoelectric composite structure; the transducer is free from the influence of outside mechanical impact and the environment temperature change. Transducer and array samples have been designed, fabricated and measured. The resonant frequency is 150 kHz, resonant transmission response greater than 160 dB, and bandwidth is from 140 kHz to 160 kHz. The results indicate that, the transducer array has wide bandwidth, high sensitivity, stabile performance, and good coherence.     

微纳相控线阵超声换能器参数的理论分析*

微纳相控线阵超声换能器参数(阵元数目、阵元宽度及阵元间距)直接影响其横向声场分布,而其横向声场分布是能否实现高成像分辨率、大探测深度的决定性因素,也是制备换能器的主要依据。该文利用数值模拟研究微纳相控线阵超声换能器阵元参数对其横向声场中主瓣强度、-3 dB主瓣宽度、第一级旁瓣及栅瓣的影响。结果表明,主瓣强度随着阵元数目增加而增大,随阵元间距减小而增大,随着阵元宽度的增大呈现先增大后减小的趋势;-3 dB主瓣宽度随着阵元数目和阵元间距的增大而减小,随着阵元宽度的减小而减小;此外,减小阵元数目、减小阵元间距或增大阵元宽度均可以抑制旁瓣;栅瓣在阵元间距满足一定条件时可以完全消除。通过这些研究为微纳相控线阵超声换能器的优化设计与制备提供理论参考。     

Miniature piezoelectric conical transducer: fabrication, evaluation and application

This paper reports a new type miniature-conical transducer for acoustic emission measurements. The transducer follows the basic idea and structure of a conventional NBS conical transducer, but is much compact in size and easier to use. The improvements are made possible by introducing an excimer laser micromachining method for fabricating smaller PZT conical elements, which play a key role in the transducer. Conical PZT elements with contact size less then 300 microm are laser-machined and the miniature-conical transducers are constructed. Standard quantitative acoustic emission testing is performed on a plate using the fabricated transducers and good results are observed. The transducers can be very useful in many applications involving quantitative measurements of transient elastic waves.     

Ultrasonic guided wave focusing by a generalized phased array

Ultrasonic guided wave focusing by a generalized phased array is studied based on dispersion curves in a multi-layered medium. The different phase of the guided waves with different frequency is added on the excitation signal on each element of the transducer array for focusing. This can be realized by designing a proper excitation pulse based on the dispersion curves of the guided waves for each of the transducer array elements. The numerical simulation results show that the guided waves with different modes, different frequency components, and from different elements of the transducer array can all be focused at the target and focusing is achieved.     

Optimization of the transfer function of an acoustooptic cell with an apodized piezoelectric transducer

It is shown that an apodized piezoelectric transducer can significantly reduce the side lobe level of the acoustooptic cell transfer function. Series and symmetric connections of the transducer sections and measures to suppress the effect of spurious elements arising in the electric circuit are proposed. In particular, the effect of spurious capacitances and inductances on the frequency response of the transducer is studied. It is shown that they violate the optimal condition for the suppression of the transfer function side lobes, especially at high frequencies. It is shown by calculations that the effect of spurious elements can be eliminated by the insertion of additional capacitors at 80 and 150 MHz.     

Electrical Control of the Frequencies of a Fabry–Perot Acoustic Resonator

The effect electronic tuning has on the frequency of the acoustic resonance of an acousto-optic modulator intended for active laser mode locking is studied theoretically and experimentally. The problem of exciting a Fabri–Perot acoustic resonator with a plate-like piezoelectric transducer is solved in the approximation of plane acoustic waves, with allowance for the real parameters of the HF generator and the matching elements of the transducer and the generator. Expressions for the basic electrical and acoustic parameters are obtained. Theoretical analysis confirms the frequency shift effect of acoustic resonances, observed earlier experimentally upon varying the matching electrical elements. The experiment is performed using an acousto-optic quartz cell and a lithium niobate transducer.     

利用锥型换能器的宽带低损耗声表面波滤波器设计

分析锥型换能器的基本原则是把换能器沿孔径方向划分成足够多的通道来进行近似,设计制作的关键是加权技术和数据处理技巧。由于SPUDT的特性,把EWC型的SPUDT引入到锥型换能器对制作宽带、低损耗器件是十分有用的;我们在Y128°LN基片上采用一般型和SPUDT型锥型换能器制作了相对带宽约15%的声表面波滤波器,一个换能器采用“块加权”,另一个换能器采用抽指加权。文中给出了两种器件的实验结果,SPUDT型声表面波滤波器的插损仅7.5dB。