纳米C和SiC掺杂对MgB2带材超导性能的影响

采用X射线衍射仪,扫描电镜,超导量子干涉仪等仪器对纳米C和SiC掺杂的MgB2带材进行了表征,并采用标准四引线法对样品的临界电流进行了测试. 实验表明,C和SiC掺杂在提高MgB2带材高场下的临界电流密度方面具有显著效果. 在温度为4.2 K、磁场大于9 T条件下,C和SiC掺杂样品的临界电流密度与未掺杂样品相比均提高一个数量级以上. 掺杂样品高磁场下良好的临界电流性能主要归因于C对B的替代所产生的晶格畸变、位错等缺陷和局部成分变化而导致的有效晶内钉扎作用. 实验结果表明,SiC掺杂的MgB2带材之所以具有非常好的高场电流特性,和C掺杂的样品一样, C对B的替代起到十分关键的作用.     

脉冲磁场处理对碳纳米管掺杂MgB2线材临界电流密度的影响

对碳纳米管(CNT)掺杂MgB₂超导体磁场处理后的行为进行了研究. 结果表明，CNT掺杂MgB₂超导体经5T脉冲磁场处理后临界电流密度J_c(H)在低磁场下提高了2—3倍，高场下提高一个数量级以上，扫描电镜结果显示CNT沿着处理磁场方向规则排列并且成为MgB₂基体的形核中心和高效的磁通钉扎中心. 关键词： 2')" href="#">MgB₂ 碳纳米管 脉冲磁场处理     

利用电泳法在金属基底上制备MgB2超导厚膜

利用电泳技术在高熔点金属基底Ta，Mo和W上制备MgB₂超导厚膜.厚膜中的MgB2晶粒结合紧密，粒度小于1μm，呈随机取向生长.电阻测量表明沉积在Ta，Mo，W上的MgB₂厚膜的超导起始转变温度分别为36.5K，34.8K，33.4K，对应的转变宽度为0.3K，1.5K和2.0K.三种基底上制备的MgB₂厚膜的临界电流密度在不同温度下随外磁场的变化情况 基本相同，MgB₂/Mo厚膜的临界电流密 关键词： 2超导厚膜')" href="#">MgB₂超导厚膜 电泳 金属基底     

纳米ZrO2掺杂对烧结DyBaCuO块材微观结构及其超导电性的影响

研究了纳米ZrO2掺杂及其掺杂浓度对烧结DyBa2Cu3Oy超导体的转变温度Tc和临界电流Ic在零磁场和磁场中的行为,在磁场中发现掺杂样品的临界电流密度明显高于纯DyBaCuO样品.这种磁场行为可能与掺杂样品粒子分布更加均匀,富纳米粒子区明显增加,从而形成有效钉扎中心有关.     

MgB2 超薄膜的制备和性质研究

利用混合物理化学气相沉积法在6H-SiC(001)衬底上制备干净的MgB₂超导超薄膜.在本底气体压强、载气氢气流量等条件一定的情况下,改变B₂H₆流量及沉积时间,制备得到不同厚度的系列MgB₂超薄膜样品,并研究了超导转变温度T_c、剩余电阻率ρ_(42K)、上临界磁场H_c2等与膜厚的关系.该系列超薄膜沿c轴外延生长,随膜厚度的变小,T_c(0)降低,ρ_(42K)升高.膜在衬底上的生长遵循Volmer-Weber岛状生长模式.对于厚度为7.5 nm的MgB₂超薄膜,T_c(0) =32.8 K,ρ_(42K) =118 μΩcm,是迄今为止所观测到的厚度为7.5 nm的MgB₂超薄膜最高的T_c值;对于厚度为10 nm的MgB₂膜,T_c(0)=35.5 K,ρ_(42K)=17.7 μΩcm,上临界磁场μ₀H_c2估算为12 T左右,零磁场、4 K时的临界电流密度J_c=1.0×10⁷ A/cm²,是迄今为止10 nm厚MgB₂超薄膜的最高J_c值,且其表面连接性良好,均方根粗糙度为0.731 nm.这预示MgB₂超薄膜在超导纳米器件上具有广阔的应用前景. 关键词： 2超薄膜')" href="#">MgB₂超薄膜 薄膜生长 氢气流量 混合物理化学气相沉积     

MgB2混合态热导率的反常增强

测量了MgB₂多晶样品的混合态热导率，磁场强度为0—7 T，温度范围为5—45 K .实验结果显示MgB₂热导率在低场下迅速上升，高场下趋于饱和，这与MgB₂的 二能隙电子结构有关.对实验结果的分析指出，低温强场下MgB₂多晶样品热导率的显著增强无法完全 用电子热导来解释，并对此进行了讨论. 关键词： 2')" href="#">MgB₂ 热导率 混合态     

MgO(111)衬底MgB2 超薄膜的制备和性质研究

利用混合物理化学气相沉积法(HPCVD)在MgO(111)衬底上制备了干净的MgB₂超导超薄膜. 在背景气体压强, 载气氢气流量以及沉积时间一定的情况下, 改变B₂H₆的流量, 制备得到不同厚度系列的MgB₂超导薄膜样品, 并测量了其超导转变温度 T_c, 临界电流密度J_c等临界参量. 该系列超导薄膜沿c轴外延生长, 表面具有良好的连接性, 且有很高的超导转变温度T_c(0) ≈ 35-38 K和很小的剩余电阻率ρ(42 K) ≈ 1.8-20.3 μΩ·cm^-1. 随着膜厚的减小而减小, 临界温度变低, 而剩余电阻率变大. 其中20 nm的样品在零磁场, 5K时的临界电流密度J_c ≈ 2.3×10⁷ A/cm². 表明了利用HPCVD在MgO(111)衬底上制备的MgB₂超薄膜有很好的性能, 预示了其在超导电子器件中广阔的应用前景. 关键词： MgO(111)衬底 2超薄膜')" href="#">MgB₂超薄膜 混合物理化学气相沉积     

硅掺杂MgB_2超导薄膜的制备及研究

本文报道了基于混合物理化学气相沉积法(Hybrid physical-chemical vapordeposition,简称为HPCVD),以硅烷热解出的Si原子作硅源,在SiC衬底上原位生长了一系列硅掺杂MgB_2超导薄膜样品.样品中最大硅掺杂量是9%.与纯净的MgB_2薄膜相比较,掺杂样品的超导临界转变温度T_c没有大幅下降,超导临界电流J_c得到了一定提升.在温度为5K,外加垂直磁场为3T的条件下,样品的临界电流密度最大达到2.7×10~5Acm~(-2).同时上临界场H_(c2)在超导转变温度附近对于温度的变化曲线斜率—dH/dT也有一定的提高.     

纳米微粒BaFe12O19掺杂对单畴超导块材GdBa2Cu3O7-δ性能的影响

磁通钉扎性能对GdBa₂Cu₃O_7-δ超导块材的实际应用具有重要的影响, 而引入合适的第二相粒子可以改善GdBa₂Cu₃O_7-δ 超导块材的磁通钉扎性能.本文采用顶部籽晶熔融织构法成功地制备出纳米微粒BaFe₁₂O₁₉(<100 nm)掺杂的超导块材, 样品的最终组分为Gd123+ 0.4 Gd211+ x BaFe₁₂O₁₉ (x=0, 0.2 mol%, 0.4 mol%, 0.8 mol%)+ 10 wt%Ag₂O+ 0.5 wt%Pt. 通过研究不同掺杂量的BaFe₁₂O₁₉微粒对GdBa₂Cu₃O_7-δ 超导块材微观结构和超导性能的影响, 结果表明当掺杂量为0.2 mol%时, 样品的临界电流密度几乎在整个外加磁场下都有明显的提高.在零场下, 临界电流密度达到5.5× 10⁴ A/cm². 纳米微粒BaFe₁₂O₁₉不仅可以保持掺杂前的化学组成, 作为有效的钉扎中心存在于超导块材中, 并且能够改善Gd₂BaCuO₅粒子的分布和细化Gd₂BaCuO₅粒子, 使Gd₂BaCuO₅粒子的平均粒径由未掺杂时的1.4 μ m减小到掺杂后的0.79 μ m, 进而提高了超导块材的临界电流密度和俘获磁场, 明显提高了GdBa₂Cu₃O_7-δ 超导块材的超导性能.临界温度T_C也有所提升, 并能够维持在92.5 K左右. 该结果为进一步研究纳米磁通钉扎中心的引入并改善GdBa₂Cu₃O_7-δ 超导块材的性能有着重要的意义.     

强磁场对金属离子掺杂CaTiO$lt;sub$gt;3$lt;/sub$gt;结构和光学性能的影响

研究了800 ℃条件下不同制备磁场强度(最高12 T)对CaTiO₃ 及其浸渍掺杂样品在结构和光学性能方面的影响. 研究表明：样品吸光性能随浸渍掺杂的离子浓度的增大而提升,且发生红移现象;相同掺杂浓度下,磁场下制备样品的吸光性能均较非磁场下制备的样品有所提高,但不同磁场强度下所制备样品的吸光曲线彼此差异不大;此外,磁制备纯CaTiO₃晶体粉末的X-射线衍射曲线峰左移,紫外-可见漫反射光谱吸收截止波长增长,这表明强磁场可使CaTiO₃晶面间距和晶格常数增大、禁带宽度减小. 关键词： 3')" href="#">CaTiO₃ 强磁场 掺杂     

高性能MgB2长线材制备及性能表征

采用原位粉末装管工艺，分别以Mg粉(99.5%)，无定形B粉(99.9%)为原料，以纳米SiC(10—30nm)作为掺杂材料制备铁基MgB₂线.首先将已混合的原料在丙酮介质中球磨，真空干燥后，将粉末填入铁管内，然后通过孔型轧制、旋锻和拉拔等冷加工工艺得到11m长外径Ф1.75mm铁基MgB₂超导线.用扫描电镜，电子能谱，X射线衍射仪和超导量子干涉仪测试发现，样品微观结构整齐，晶粒大小均匀，内部仅含微量MgO，T_C(onset)=35.1K，ΔT_C＝5.3K.纳米SiC掺杂后，其中C造成MgB₂晶格畸变，形成有效磁通钉扎中心，C元素在MgB₂中分布均匀.标准四引线测试结果表明，11m线均分10段后，各点的J_c(4.2K,10T)均超过1.0×10⁴A/cm^{2，最高值达到1.2×104A/cm2.在10—18T范围各点临界电流值分布均匀，变化率小于10%.}     

MgB2 coated superconducting tapes with high critical current densities fabricated by hybrid physical-chemical vapor deposition

The MgB₂ coated superconducting tapes have been fabricated on textured Cu (0 0 1) and polycrystalline Hastelloy tapes using coated conductor technique, which has been developed for the second generation high temperature superconducting wires. The MgB₂/Cu tapes were fabricated over a wide temperature range of 460-520 °C by using hybrid physical-chemical vapor deposition (HPCVD) technique. The tapes exhibited the critical temperatures (T_c) ranging between 36 and 38 K with superconducting transition width (ΔT_c) of about 0.3-0.6 K. The highest critical current density (J_c) of 1.34 × 10⁵ A/cm² at 5 K under 3 T is obtained for the MgB₂/Cu tape grown at 460 °C. To further improve the flux pinning property of MgB₂ tapes, SiC is coated as an impurity layer on the Cu tape. In contrast to pure MgB₂/Cu tapes, the MgB₂ on SiC-coated Cu tapes exhibited opposite trend in the dependence of J_c with growth temperature. The improved flux pinning by the additional defects created by SiC-impurity layer along with the MgB₂ grain boundaries lead to strong improvement in J_c for the MgB₂/SiC/Cu tapes. The MgB₂/Hastelloy superconducting tapes fabricated at a temperature of 520 °C showed the critical temperatures ranging between 38.5 and 39.6 K. We obtained much higher J_c values over the wide field range for MgB₂/Hastelloy tapes than the previously reported data on other metallic substrates, such as Cu, SS, and Nb. The J_c values of J_c(20 K, 0 T) ∼5.8 × 10⁶ A/cm² and J_c(20 K, 1.5 T) ∼2.4 × 10⁵ A/cm² is obtained for the 2-μm-thick MgB₂/Hastelloy tape. This paper will review the merits of coated conductor approach along with the HPCVD technique to fabricate MgB₂ conductors with high T_c and J_c values which are useful for large scale applications.     

Effects of nano-carbon doping and sintering temperature on microstructure and properties of MgB2

We fabricated nano-carbon (NC) doped MgB₂ bulks using an in situ process in order to improve the critical current density (J_c) under a high magnetic field and evaluated the correlated effects of the doped carbon content and sintering temperature on the phase formation, microstructure and critical properties. MgB_2−xC_x bulks with x = 0 and 0.05 were fabricated by pressing the powder into pellets and sintering at 800 °C, 900 °C, or 1000 °C for 30 min.We observed that NC was an effective dopant for MgB₂ and that part of it was incorporated into the MgB₂ while the other part remained (undoped), which reduced the grain size. The actual C content was estimated to be 68–90% of the nominal content. The NC doped samples exhibited lower T_c values and better J_c(B) behavior than the undoped samples. The doped sample sintered at 900 °C showed the highest J_c value due to its high doping level, small amount of second phase, and fine grains. On the other hand, the J_c was decreased at a sintering temperature of 1000 °C as a result of the formation of MgB₄ phase.     

Concurrent doping effect of Ti and nano-diamond on flux pinning of MgB2

Nano-diamond and titanium concurrently doped MgB₂ nanocomposites have been prepared by solid state reaction method. The effects of carbon and Ti concurrent doping on J_c–H behavior and pinning force scaling features of MgB₂ have been investigated. Although T_c was slightly depressed, J_c of MgB₂ have been significantly improved by the nano-diamond doping, especially in the high field region. In the mean time, the J_c value in low field region is sustained though concurrent Ti doping. Microstructure analysis reveals that when nano-diamond was concurrently doped with titanium in MgB₂, a unique nanocomposite in which TiB₂ forms a thin layer surrounding MgB₂ grains whereas nano-diamond particles were wrapped inside the MgB₂ grains. Besides, nano-diamond doping results in a high density stress field in the MgB₂ samples, which may take responsibility for the Δκ pinning behavior in the carbon-doped MgB₂ system.     

Stoichiometry dependence of the critical current density in pure and nano-SiC doped MgB2/Fe tapes

The stoichiometry dependence of the microstructure and superconducting properties of pure and nano-SiC doped MgB₂/Fe tapes was systematically investigated. The tapes prepared with the composition of a slight deficiency of Mg (Mg_0.9B₂ and Mg_xB₂(SiC)_0.1 (x = 0.9 and 1.0)) showed the best transport J_c. Adding a slight excess of Mg like 5%, as being done by many researchers, was not beneficial for the J_c improvement as expected. The onset T_c was not significantly changed in both doped and undoped tapes by adding excess of boron or magnesium, but the transition widths were broadened due to the induced impurities. The slightly-Mg-deficient pure samples show smaller grain sizes, which corresponds to a better J_c–B performance at high magnetic field due to the enhanced grain boundary pinning. The field dependence of J_c in nano-SiC doped tapes was almost not influenced by varying the starting Mg content although microstructural difference can still be seen, suggesting that the flux pinning ability was mainly controlled by the carbon substitution effect for boron.     

Effect of SiC buffer layer on flux pinning property of MgB2 tapes

In this paper we aimed at investigating the flux pinning property of MgB₂ films on hastelloy tapes which are buffered on various thicknesses of SiC layers. We have observed that the increase in thickness of the SiC buffer layer is very closely related with the systematic improvement of the field dependence of the critical current densities (J_c) of MgB₂ tapes while the values of J_c decreased. According to the analysis of the pinning force density (F_p), there exist two pinning sources both in the pure MgB₂ and in the MgB₂ film with the thinnest SiC buffer layer. On the while, the pinning source observed in the MgB₂ films with thicker SiC buffer layers appears to be different from those previously mentioned. The different pinning behaviors of MgB₂ films may suggest that there be an additional pinning center working on the MgB₂ films with thick SiC buffer layers. The microstructural analyses of MgB₂ films confirmed that intra-granular defects and columnar grain boundaries may be a dominant pinning mechanism in the pure MgB₂ and the MgB₂ film with 170 nm-thick SiC buffer layer. For the MgB₂ films with thicker SiC buffer layers, carbon diffusion into the MgB₂ film, which is defined by the Auger electron spectroscopy, may be the origin of the additional pinning mechanism.     

Effects of doping with nanoscale Co3O4 particles on the superconducting properties of powder-in-tube processed MgB2 tapes

Nanoscale Co₃O₄ particles were doped into MgB₂ tapes with the aim of developing superconducting wires with high-current-carrying capacity. Fe-sheathed MgB₂ tapes with a mono-core were prepared using the in situ powder-in-tube (PIT) process with the addition of 0.2–1.0 mol% Co₃O₄. The critical temperature decreased monotonically with an increasing amount of doped Co₃O₄ particles for all heat-treatment temperatures from 600 to 900 °C. However, the transport critical current density (J_c) at 4.2 K varied with the heat-treatment temperatures. The J_c values in magnetic fields ranging from 7 to 12 T decreased monotonically with increasing Co₃O₄ doping level for a heat-treatment temperature of 600 °C. In contrast, some improvements on the J_c values of the Co₃O₄ doped tapes were observed in the magnetic fields below 10 T for 700 and 800 °C. Furthermore, J_c values in all the fields measured increased as the Co₃O₄ doping level increase from 0 to 1 mol% for 900 °C. This heat-treatment temperature dependence of the J_c values could be explained in terms of the heat-treatment temperature dependence of the irreversibility field with Co₃O₄ doping.     

柠檬酸掺杂的MgB2超导体钉扎机理的研究

本文研究了柠檬酸掺杂的MgB₂超导材料的J_c-B行为及其钉扎机理.在纯MgB₂多晶样品中,δT_c钉扎起主要作用,而在掺杂的样品中,则是δl钉扎和δT_c钉扎共同作用,并且δl钉扎机理占主要作用,其贡献比重随着掺杂量的增加而增加.从J_c-B行为和钉扎行为的分析都可以得到 关键词： 柠檬酸 2')" href="#">MgB₂ T_c钉扎')" href="#">δT_c钉扎 l钉扎')" href="#">δl钉扎     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.