Imaging the diffusion pathway of Al~(3+) ion in NASICON-type(Al_(0.2)Zr_(0.8))_(20/19)Nb(PO_4)_3 as electrolyte for rechargeable solid-state Al batteries

Among all-solid-state batteries, rechargeable Al-ion batteries have attracted most attention because they involve threeelectron-redox reactions with high theoretic specific capacity. However, the solid Al-ion conductor electrolytes are less studied. Here, the microscopic path of Al~(3+)-ion conduction of NASICON-type(Al_(0.2)Zr_(0.8))_(20/19)Nb(PO_4)_3 oxide is identified by temperature-dependent neutron powder diffraction and aberration-corrected scanning transmission electron microscopy experiments.(Al_(0.2) Zr_(0.8))_(20/19) Nb(PO_4)_3 shows a rhombohedral structure consisting of a framework of(Zr,Nb)O_6 octahedra sharing corners with(PO_4) tetrahedra; the Al occupy trigonal antiprisms exhibiting extremely large displacement factors. This suggests a strong displacement of Al ions along the c axis of the unit cell as they diffuse across the structure by a vacancy mechanism. Negative thermal expansion behavior is also identified along a and b axes, due to folding of the framework as temperature increases.     

Effects of Al particles and thin layer on thermal expansion and conductivity of Al-Y_2Mo_3O_(12) cermets

Low thermal expansion composites are difficult to obtain by using Al with larger positive thermal expansion coefficient(TEC) and the materials with smaller negative TECs. In this investigation, Y_2Mo_3O_(12) with larger negative TEC is used to combine with Al to obtain a low thermal expansion composite with high conductivity. The TEC of Al is reduced by 19%for a ratio Al:Y_2Mo_3O_(12) of 0.3118. When the mass ratio of Al:Y_2Mo_3O_(12) increases to 2.0000, the conductivity of the composite increases so much that a transformation from capacitance to pure resistance appears. The results suggest that Y_2Mo_3O_(12) plays a dominant role in the composite for low content of Al(presenting isolate particles), while the content of Al increases enough to contact each other, the composite presents mainly the property of Al. For the effect of high content Al, it is considered that Al is squeezed out of the cermets during the uniaxial pressure process to form a thin layer on the surface.     

Laser scattering,transmittance and low thermal expansion behaviors in Y_(2-x)(ZnLi)_xMo_3O_(12) by forming regular grains

Ceramics usually have irregular grains, cracking, or porosity, which result in their lightproof.Y_2Mo_3O_(12) ceramics have more porosity due to the heavy hygroscopicity.Introducing ZnLi to Y_2Mo_3O_(12) could form regular grains, reduce cracking and porosity.With increasing the content of ZnLi, the grain shapes self-assembly gradually and then the laser scattering and transmittance improve.The laser scattering property and transmittance of diverging rays become the best in ceramics Y_(2-x)(ZnLi)_xMo_3O_(12)(x = 1.0 and 1.2) with regular grains and low thermal expansion.The formation mechanism of regular grains is ascribed to the substitutions of Zn~(2+)and Li+for Y~(3+) in Y_2Mo_3O_(12) resulting in the preferential growth.The investigation in laser scattering, transmittance and low thermal expansion behaviors of Y_(2-x)(ZnLi)_xMo_3O_(12) could pave a way to weaken the strong-laser attack from the high-power laser weapon and the other.     

Substitution priority of Eu~(2+) in multi-cation compound Sr_(0.8)Ca_(0.2)Al_2Si_2O_8 and energy transfer

A blue phosphor was obtained by doping Eu~(2+)into a multi-cation host Sr_(0.8)Ca_(0.2)Al_2Si_2O_8 through high temperature solid state reaction.The emission spectra show a continuous red-shift behavior from 413 nm to 435 nm with Eu~(2+)concentration increasing.The substitution priority of Eu~(2+)in Sr_(0.8)Ca_(0.2)Al_2Si_2O_8 was investigated via x-ray diffraction(XRD)and temperature properties in detail:the Ca~(2+)ions are preferentially substituted by Eu~(2+)at lower doping,and with the Eu~(2+)concentration increasing,the probability of substitution for Sr~(2+)is greater than that of replacing Ca~(2+).Accordingly,we propose the underlying method of thermal property to determine the substitution of Eu~(2+)in the multi-cation hosts.Moreover,the abnormal increase of emission intensity with increasing temperature was studied by the thermoluminescence spectra.The energy transfer mechanism between the Eu~(2+)ions occupying different cation sites was studied by the lifetime decay curves.A series of warm white light emitting diodes were successfully fabricated using the blue phosphors Sr~+_(0.8)Ca_(0.2)Al_2Si_2O_8:Eu~2 with commercial red phosphor (CaSr)SiAlN_3:Eu~(2+)and green phosphor(Y Lu)_3Al_5O_(12):Ce~(3+),and the luminescent efficiency can reach 45 lm/W.     

Molten-salt synthesis and composition-dependent luminescent properties of barium tungsto-molybdate-based solid solution phosphors

Pr~(3+)-activated barium tungsto-molybdate solid solution phosphor Ba(Mo_(1-z)W_z)O_4:Pr~(3+)is successfully fabricated via a facile molten-salt approach. The as-synthesized microcrystal is of truncated octahedron and exhibits deep-red-emitting upon blue light excitation. Powder x-ray diffraction and Raman spectroscopy techniques are utilized to investigate the formation of solid solution phosphor. The luminescence behaviors depend on the resulting composition of the microcrystals with fixed Pr~(3+)-doping concentration, while the host lattices remain in a scheelite structure. The forming solid solution via the substitution of [WO_4] for [MoO_4] can significantly enhance its luminescence, which may be due to the fact that Ba(Mo_(1-z)W_z)O_4:Pr~(3+)owns well-defined facets and uniform morphologies. Owing to its properties of high phase purity,well-defined facets, highly uniform morphologies, exceptional chemical and thermal stabilities, and stronger emission intensity, the resulting solid solution phosphor is expected to find potential applications in phosphor-converted white lightemitting diodes(LEDs).     

Er0.1La0.9P5O14非晶的双光子上转换发光

本文研究了全浓度ＥｒＬａＰ５Ｏ１４非晶在波长λ为６４９．０ｎｍ脉冲染料激光激发下的上转换发光现象，并对其进行了简要的分析。     

Influences of different oxidants on characteristics of La_2O_3/Al_2O_3 nanolaminates deposited by atomic layer deposition

A comparative study of two kinds of oxidants(H_2O and O_3) with the combination of two metal precursors(TMA and La(~iPrCp)_3) for atomic layer deposition(ALD) La_2O_3/Al_2O_3 nanolaminates is carried out. The effects of different oxidants on the physical properties and electrical characteristics of La_2O_3/Al_2O_3 nanolaminates are studied. Initial testing results indicate that La_2O_3/Al_2O_3 nanolaminates could avoid moisture absorption in the air after thermal annealing. However, moisture absorption occurs in H_2O-based La_2O_3/Al_2O_3 nanolaminates due to the residue hydroxyl/hydrogen groups during annealing. As a result, roughness enhancement, band offset variation, low dielectric constant and poor electrical characteristics are measured because the properties of H_2O-based La_2O_3/Al_2O_3 nanolaminates are deteriorated. Addition thermal annealing effects on the properties of O_3-based La_2O_3/Al_2O_3 nanolaminates indicate that O_3 is a more appropriate oxidant to deposit La_2O_3/Al_2O_3 nanolaminates for electron devices application.     

Comparison between AlN and Al_2O_3 ceramics applied to barrier dielectric of plasma actuator

This paper reports the material characterization and performance evaluation of an AlN ceramic based dielectric barrier discharge(DBD) plasma actuator. A conventional Al_2O_3 ceramic is also investigated as a control. The plasma images,thermal characteristics and electrical properties of the two actuators are compared and studied. Then, with the same electrical operating parameters(12-kV applied voltage and 11-kHz power frequency), variations of the surface morphologies,consumed power and induced velocities are recorded and analyzed. The experimental results show that the AlN actuator can produce a more uniform discharge while the discharge of the Al_2O_3 actuator is easier to become filamentary. The later condition leads to higher power consumption and earlier failure due to electrode oxidation. In the plasma process,the power increment of the AlN actuator is higher than that of the Al_2O_3 actuator. The induced velocity is also influenced by this process. Prior to aging, the maximum induced velocity of the AlN actuator is 4.2 m/s, which is about 40% higher than that of the Al_2O_3 actuator. After 120-min plasma aging, the maximum velocity of the aged AlN actuator decreases by 27.8% while the Al_2O_3 actuator registers a decrease of 25%.     

二维周期性多孔La_(0.83)Sr_(0.17)Mn_(0.9)Zn_(0.1)O_3发射率研究

基于麦克斯韦方程组,利用时域有限差分方法(FDTD)计算了二维周期性多孔钙钛矿型氧化物La_(0.83)Sr_(0.17)Mn_(0.9)Zn_(0.1)O_3(LSMZO)的光谱特性,讨论了结构尺寸对光谱特性的影响。计算结果表明,当孔径约比热辐射波长小一个量级时,周期性多孔LSMZO的发射率比块体材料有所提高,这对改善热致变色材料的性能具有一定的指导意义。     

980nm激光激发下Er3+和Yb3+共掺杂氟氧玻璃的上转换发光

制备了一种新型的上转换发光材料,它不仅具有较高的上转换发光效率,而且还避免了氟化物基质的缺点。其组分为58.52%PbF₂-34.43% GeO₂-3% Al₂O₃-0.05% Er₂O₃-4%Yb₂O₃,其中GeO₂为玻璃形成体氧化物,PbF₂和Al₂O₃为调整剂,以共掺杂Er³⁺和Yb³⁺离子为上转换研究的对象。测量了该玻璃系统在980nm半导体激光器激发下的上转换发光光谱,观察到很强的658nm的红光和548,526nm的绿光,而且红光的发射强度远远强于绿光。通过对上转换发光强度与激发强度关系曲线的拟合,表明此材料的绿光发射和红光发射都为双光子过程。研究了激发光的工作电流与上转换荧光强度的关系,讨论了其上转换发光特性。     

Ca~(2+)离子替代对Sr_4Al_(14)O_(25):Eu~(2+),Dy~(3+)结构和发光性能的影响

采用高温固相反应按化学式Sr4-xCaxAl14O25:Eu2+,Dy3+(x=0,0.8,1.6,2.4,3.2,4)配比原料,合成长余辉发光材料.X射线衍射分析表明当x2.4时,产物物相均为Sr4Al14O25正交结构;当x2.4时,产物物相转变为CaAl4O7单斜结构.对掺Ca量不同,但结构仍保持Sr4Al14O25的样品采用360nm激光照射,发射光谱表明样品发光均由以Eu2+为发光中心的电子4f65d→4f7跃迁所致,并且随着Ca掺入量的增加,样品发射光谱峰位逐渐蓝移.这是由于Ca2+取代Sr2+位置后,导致晶格收缩,影响Eu2+的5d能级劈裂情况,从而影响电子4f65d→4f7跃迁.余辉衰减检测和热释光谱分析发现,不同Ca掺入量的样品余辉衰减快慢不同,是由于其中存在的陷阱能级深度不同,且陷阱能级越深,其余辉时间越长.     

Thermal expansion properties of Lu2-xFexMo3O12

The structures and thermal expansion properties of Lu2-xFexMo3O12 have been investigated by X-ray diffraction(XRD).XRD patterns at room temperature indicate that compounds Lu2-xFexMo3O12 with x≤1.3 exhibit an orthorhombic structure with space group Pnca;compounds with x=1.5 and 1.7 have a monoclinic structure with space group P21/a.Studies on thermal expansion properties show that the linear thermal expansion coefficients of orthorhombic phase vary from negative to positive with increasing Fe content.Attempts to make zero thermal expansion materials indicate that zero thermal expansion can be observed in Lu1.3Fe0.7Mo3O12 in the temperature range of 200-400℃.     

Fe2-xYxMo3O12系列材料的相变及负膨胀性研究

本文对Fe2-xYx(MoO4)3(x=0.0,0.2,0.4,0.5,0.6,0.8,1.0,1.2,1.4,1.6,1.8,2.0)系列材料的相变及负膨胀性能进行了研究.通过对Fe2-xYx( MoO4)3系列材料的XRD和拉曼谱的分析发现,当x≤0.4时Fe2-xYxMo3O12在常温下是单斜结构;当x≥0.5时...     

荧光粉(Ca2.94-xLuxCe0.06)(ScMg)Si3O12的晶体结构和荧光性质

利用高温固相反应制备了一种由Lu改进的黄色荧光粉(Ca2.94-x LuxCe0.06)(ScMg)Si3O12(缩写为CKSMS:Ce3+),其中,0≤x≤0.94.同时研究了Lu含量对荧光粉的晶相、发光性质以及温度特性的影响.结果表明,Lu的引入导致荧光增强,其原因是由于Ce3+吸收增强而不是荧光粉内量子效率增加....     

Predicting Physical Properties of Tetragonal,Monoclinic and Orthorhombic M_3N_4(M=C,Si,Sn) Polymorphs via First-Principles Calculations

The recently discovered tetragonal,monoclinic and orthorhombic polymorphs of M_3N_4(M=C,Si,Sn) are investigated by using first-principles calculations.A set of anisotropic elastic quantities,i.e.,the bulk and shear moduli,Young's modulus,Poisson ratio,B/G ratio and Vickers hardness of M_3N_4(M=C,Si,Sn) are predicted.The quasi-harmonic Debye model,assuming that the solids are isotopic,may lead to large errors for the non-cubic crystals.The thermal effects are obtained by the traditional quasi-harmonic approach.The dependences of heat capacity,thermal expansion coefficient and Debye temperature on temperature and pressure are systematically discussed in the pressure range of 0-10 GPa and in the temperature range of 0-1100 K.More importantly,o-C_3N_4 is a negative thermal expansion material.Our results may have important consequences in shaping the understanding of the fundamental properties of these binary nitrides.     

Total Ionization Dose Effects on Charge Storage Capability of Al_2O_3/HfO_2/Al_2O_3-Based Charge Trapping Memory Cell

Because of the discrete charge storage mechanism, charge trapping memory(CTM) technique is a good candidate for aerospace and military missions. The total ionization dose(TID) effects on CTM cells with Al_2O_3/HfO_2/Al_2O_3(AHA) high-k gate stack structure under in-situ 10 keV x-rays are studied. The C-V characteristics at different radiation doses demonstrate that charge stored in the device continues to be leaked away during the irradiation,thereby inducing the shift of flat band voltage(V_(fb)). The dc memory window shows insignificant changes, suggesting the existence of good P/E ability. Furthermore, the physical mechanisms of TID induced radiation damages in AHA-based CTM are analyzed.     

(Y,Gd)Al3(BO3)4:Tb的真空紫外光谱特性

(Y,Gd)Al3(BO3)4属于三角晶系,具有R32的空间群,掺入Ce3 ,Tb3 杂质后,其晶格结构没有变化。(Y,Gd)Al3(BO3)4:Tb随着Gd3 摩尔浓度增大,基质吸收带红移。Gd3 和Tb3 之间存在着很有效的能量传递。Gd3 摩尔浓度在一定范围内(0~0·75mol)增大时,样品在120~300nm光谱范围内的激发强度均是增强的;但是,Gd3 浓度过高造成Gd3 的发射增强,GdAl3(BO3)4:Tb在120~240nm光谱范围内激发强度很明显下降。(Y,Gd)Al3(BO3)4:Ce,Tb在真空紫外激发下,发现Tb3 的发光明显的被Ce3 猝灭。     

Near-zero thermal expansion of In_(2(1-x))(HfMg)_xMo_3O_(12) with tailored phase transition

Solid solutions of In_(2(1-x)(HfMg)_xMo_3O_(12) are synthesized by solid state reaction with the aim to reduce the phase transition temperature of In_2Mo_3O_(12) and improve its thermal expansion property.The effects of(HfMg)~(6+) incorporation on the phase transition and thermal expansion are investigated.It is shown that the monoclinic-to-orthorhombic phase transition temperature obviously decreases and the coefficient of thermal expansion(CTE) of the orthorhombic becomes less negative and approaches to zero with increasing the content of(HfMg)~(6+).A near zero thermal expansion covering the case at room temperature(RT) is achieved for the solid solutions with x ≥ 0.85,implying potential applications of this material in many fields.     

Enhanced hyperthermia performance in hard-soft magnetic mixed Zn0.5CoxFe2.5−xO4/SiO2 composite magnetic nanoparticles

High quality Zn0.5CoxFe2.5?xO4(x=0,0.05,0.1,0.15)serial magnetic nanoparticles with single cubic structures were prepared by the modified thermal decomposition method,and Zn0.5CoxFe2.5?xO4/SiO2 composite magnetic nanoparticles were prepared by surface modification of SiO2.The magnetic anisotropy of the sample increases with the increase of the doping amount of Co2+.When the doping amount is 0.1,the sample shows the transition from superparamagnetism to ferrimagnetism at room temperature.In the Zn0.5CoxFe2.5?xO4/SiO2 serial samples,the maximum value of specific loss power(SLP)with 1974 W/gmetal can also be found at doping amount of x=0.1.The composite nanoparticles are expected to be an excellent candidate for clinical magnetic hyperthermia.     

基质组成对Eu,Dy共掺杂铝酸锶发光性能的影响

研究了基质组成对xSrO·yAl₂O₃:Eu²⁺,Dy³⁺体系长余辉发光性能的影响,并对其影响机理进行了探讨.XRD分析结果和长余辉发光性能表明,改变Al₂O₃/SrO比率可以获得长余辉发光性能较好的三种基质相:SrAl₂O₄:Eu²⁺,Dy³⁺、Sr₄Al₁₄O₂₅:Eu²⁺,Dy³⁺和SrAl₄O₇:Eu²⁺,Dy³⁺.激发与发射光谱性能分析和余辉衰减特性分析结果表明,随着基质中Sr/Al比例的减小,激发光谱向短波方向延伸,发射峰蓝移,初始余辉亮度越高,余辉持续时间越长.热释光谱分析表明,贫锶相晶格中的陷阱深度与密度较大,因而显示出较好的长余辉发光性能.