磁性石榴石单晶Bi-YIG的布里渊散射

本文报道用激光布里渊散射法测量Bi_xY_3-xFe₅O₁₂(x=0,0.14,0.36,0.54)室温下的布里渊散射,观察到了热激发体磁振子散射,依据磁振子的频率-磁场关系,导出了材料的磁性参数。并发现了Bi代入时引起的自旋波劲度系数的增大现象。 关键词：     

Bi离子掺杂GeO2-Al2O3-M(M=Na2O,BaO,Y2O3)玻璃的光学性质

用高温熔融法制备了Bi离子掺杂浓度为1mol%的GeO-B2O3-Na2O (GBNB),GeO2-Al2O3-Na2O(GANB),GeO2-Al2O3-BaO(GABB)和GeO2-Al2O3-Y2O3(GAYB)玻璃.测定了样品玻璃的差热曲线、吸收、发射光谱及荧光衰减曲线.实验发现GBNB,GANB,GAYB,GABB的吸收边带逐步发生红移.由于这些吸收边带是由Bi3+的6s2电子到Bi5+ 6s0空轨道的跃迁引起.因此推断GBNB,GANB,GAYB,GABB玻璃中Bi5+离子的含量逐步增加.在GABB,GAYB,GANB三个样品中观察到发光中心约1220nm超宽带荧光发射.荧光强度从GABB,GAYB,GANB逐步减弱,荧光半高宽和荧光寿命逐步变小.这些超宽带的荧光归属为Bi5+离子的发光所致.从吸收与荧光光谱的变化,推断在GeO2-Al2O3玻璃中引入BaO,Y2O3组分有利于Bi5+离子的形成.讨论了BaO,Y2O3化学组分对Bi离子在玻璃中的价态影响的内在机理.     

退火处理对W:Bi4Ge3O12和Bi12GeO20晶体发光性能的影响

通过提拉法制备了W:Bi4 Ge3 O12和Bi12GeO20晶体,测试了晶体的吸收光谱、光致发光谱和发光衰减时间等.W:Bi4 Ge3 O12的可见光发光强度比纯Bi4 Ge3 O12有所增强,而且N2中退火处理对W:Bi4Ge3O12发光有进一步增强作用.Bi12GeO20在N2中退火处理后在745 nm附近有发光...     

钬铝石榴石晶场参数调整

利用比热实验值,对钬铝石榴石（Ho3Al5O12）晶体的晶场参数进行了调整,依此计算了Ho3Al5O12晶体的晶场能谱、Zeeman劈裂能级和波函数. 在外磁场H=0时,分别计算了Ho3Al5O12晶体的总比热、总熵随温度的变化,以及外磁场H=10kOe时该晶体倒数磁化率的温度关系,理论计算结果均与已有实验数据符合较好.该工作为进一步探究该晶体的其它性质奠定了必要的理论基础,对实际生产和科学研究中磁制冷材料的优化选取也具有一定的现实意义.     

阳离子取代对Lu_3Ga_5O_(12)∶Tb~(3+)晶体结构与发光性能的影响

采用高温固相法制备了Lu3Ga5O12:Tb3+体系荧光粉,研究了Y3+、Gd3+和Al3+离子分别取代Lu3+和Ga3+离子后对荧光粉晶体结构和发光性能的影响。结果表明,Lu3Ga5O12∶Tb3+具有石榴石结构,激发光谱由A、B两个宽激发带及一些窄谱峰构成,分别归属于Tb3+的4f8→4f75d1和4f8→4f8的电子跃迁。紫外激发下的发射光谱对应于Tb3+5D4→7FJ和5D3→7FJ跃迁。对于(Lu,Y)3Ga5O12∶Tb3+体系,随着Y3+浓度的增加,晶格膨胀,A、B宽带红移,带间距缩小,激发与发射强度提高。对于(Lu,Gd)3Ga5O12∶Tb3+体系,当Gd3+浓度低于0.75时,随着Gd3+浓度的增加,荧光粉性能变化与引入Y3+时情况相似,并更为显著;实验中观察到Gd3+→Tb3+能量传递现象。对于Lu3(Ga,Al)5O12∶Tb3+体系,随着Al3+含量的增加,晶格收缩,A、B宽带红移,带间距扩大,激发与发射强度提高。阳离子的半径差异及其引起的Tb3+晶场环境的变化是影响荧光粉性能的主要原因。     

粉末晶体(ZrO2)x(Bi2O3)1-x(x=1.0, 0.97) 晶体结构分析

为了确定ZrO2和(ZrO2)0.97(Bi2O3)0.03的晶体结构和原子热振动各向同性温度因子B，对该粉末晶体进行X射线衍射实验，建立了晶体结构模型，进行晶体结构分析。首先，采用共沉淀法和高温固相烧结法制备了纳米氧化锆ZrO2和(ZrO2)0.97(Bi2O3)0.03粉末晶体，接着，使用X射线测试仪对两种样品进行了衍射实验（XRD），利用Rietveld 精修方法的 RIETAN-2000程序对所得实验结果进行了晶体结构分析，获得了晶体结构参量和原子热振动各向同性温度因子B。通过Maximum Entropy Method（MEM）解析得到了粉末晶体(ZrO2)x(Bi2O3)1-x(x=1.0，0.97)的等高电子密度分布可视化图谱。结果表明，(ZrO2)0.97(Bi2O3)0.03的晶胞体积比ZrO2的晶胞体积大分别为140.6850 Å3和140.5637Å3；ZrO2晶体的原子热振动各向同性温度因子B(Zr)、BO(1)、BO(2)和 B（Bi）分别为0.690、0.269、 0.178 和 0 Å2，(ZrO2)0.97(Bi2O3)0.03晶体的分别为0.460 、0.583 、0.121 和0.581 Å2。 确定了(ZrO2)0.97(Bi2O3)0.03的晶体结构属于单斜晶系，实现了等高电子密度分布三维（3D）和二维（2D）的可视化，进一步确定了晶体结构和原子位置。     

CaCu_xMn_(3-x)Mn_4O_(12)(x=0.2,0.4,0.6,0.8,1.0,1.2,1.4)的结构及磁电阻效应的研究

利用湿化学反应法制备了CaCuxMn3-xMn4O12(x=0.2,0.4,0.6,0.8,1.0,1.2,1.4)系列材料的前驱体,然后加入10wt%的KCL后,在850℃的纯氧中烧结制成样品。X射线衍射表明,CaCuxMn3-xMn4O12样品呈单相立方结构,空间群Im 3-。研究表明:随掺杂浓度x的增加,晶格常数减小,晶体结构发生畸变,从而直接影响材料的电输运性质。实验表明,样品在5T的外磁场下,随x的增大,样品的磁电阻MR呈现先增大后减小的趋势,在x=1.0时磁电阻达到最大,这可能是晶粒边界处粒子的自旋极化散射和双交换作用共同作用的结果。     

Bi_4Ge_3O_(12)晶体的磁光法拉第旋转

在可见光范围测量了Bi_4Ge_3O_(12)晶体磁光法拉第旋转的色散关系,也测量了从室温到液氮温度磁光旋转在633nm的变化。大的磁光旋转和很宽光波范围的高透过率表明晶体在磁光应用上也是很有价值的。扼要讨论了Bi离子在抗磁晶体中对磁光旋转的重要作用。     

用于光纤电流传感器的掺Bi稀土铁石榴石单晶生长与磁光性能

用熔盐法生长了两种Bi替代的高法拉第旋转、温度稳定的稀土铁石榴石磁光单晶Bi-HoYbIG和Bi-GdYIG,测试分析了其在近红外波段的磁光性能及其温度特性。Ho3-z-y,YbyiBixFe512(x＝1.03,y=1.20)单晶的比法拉第旋转角为-891°/cm(λ=1.31μm)和-767°/cm(λ＝1.55μm),Y3-z-yGdyBixFe5O12(x=0.46,y=0.24)单晶的值为－1067°／cm(λ=1.31μm)和-882°／cm(λ=1.55μm),两者都比纯YIG晶体高出许多。而且这两种晶体的法拉第旋转角随温度变化较小,在250～400K范围内,其温度灵敏度S分别为4. 60×10-4／K和4. 20×10-4/K。分析表明,Bi的掺入能大大提高晶体的法拉第旋转角,而yb3+、Gd3+等离子的掺入可以有效降低Bi3+替代磁光单晶的法拉第旋转的温度灵敏性,Bi-HoYbiG和Bi-GdYIG等磁光晶体非常适合作为高灵敏度、温度稳定的光纤电流传感器中的法拉第转子材料。     

用于光纤电流传感器的BGO晶体磁光特性研究

在理论分析Bi4Ge3O12（BGO）晶体磁光特性的基础上，利用倍频法测量了不同工作波长下BGO晶体的费尔德常量，获得了与理论相符的实验结果.同时根据BGO晶体费尔德常量随波长的变化关系曲线，通过对该晶体吸收系数的测量，得出了其磁光优值曲线.进而将BGO晶体的磁光特性与光纤电流传感器常用的几种磁光材料作了对比，结果表明BGO晶体适合用于光纤电流传感器.     

Microwave-assisted synthesis and characterization of Bi-substituted yttrium garnet nanoparticles

Bi-substituted yttrium iron garnet (Bi-YIG, Bi_1.8Y_1.2Fe₅O₁₂) nanoparticles were prepared by microwave-assisted co-precipitation as well as conventional co-precipitation using ammonia aqueous solution as precipitant. The nanoparticles were characterized by thermal gravity-differential thermal analysis, X-ray powder diffraction, transmission electron microscopy, dynamic light scattering and vibrating sample magnetometer, respectively. The Faraday rotation of Bi-YIG modified PMMA slices was also investigated. Results demonstrate that the Bi-YIG nanoparticles prepared by microwave-assisted co-precipitation show smaller particle size and higher Faraday rotation than those prepared by conventional co-precipitation.     

Preparation and Faraday rotation of Bi-YIG/PMMA nanocomposite

Bismuth-substituted yttrium iron garnet (Bi-YIG) nanoparticles (NPs) were prepared by coprecipitation and subsequent heating treatment. Thermal gravity-differential thermal analysis was performed to investigate the thermal behavior of the Bi-YIG precursors and to decide the best annealing temperature. Phase formation of garnet NPs was investigated by X-ray powder diffraction. The size of Bi-YIG NPs was investigated by transmission electron microscopy, and the magnetic properties of Bi-YIG NPs were measured using a vibrating sample magnetometer. The results show that the temperature needed for the transformation of Bi-YIG from the amorphous phase to the garnet phase decreases with increasing Bi content, and Bi-YIG NPs with sizes of 28–78 nm are obtained after heating treatment at 650–1000 °C. The saturation magnetization of Bi-YIG NPs increases as the Bi content increases. Moreover, the Faraday rotation of polymethyl methacrylate (PMMA) slices doped with Bi-YIG NPs was investigated. The results indicate that the angle of Faraday rotation increases with increasing Bi content in PMMA composites, and the maximum value of the figure of merit is 1.46°, which is comparable to the value of a sputtered film. The Bi-YIG NPs-doped PMMA slices are new promising materials for magneto-optical devices.     

BCVIG单晶的布里渊散射

用布里渊散射技术测量了BCVIG(Bi_3-2xCa_2xFe_5-xV_xO₁₂)单晶的磁振子散射谱,同Sande-rcock,Wettling对YIG以及刘玉龙等人对Bi-YIG单晶的测量相比,我们得到了除主峰之外的连续谱带。按照偶极-交换自旋波理论讨论了测到的自旋波谱。测量还表明BCVIG单晶的自旋波劲度系数D比YIG和Bi-YIG单晶大得多,讨论了D增大的原因,研究了D与入射激光功率的关系。 关键词：     

Brillouin light scattering study of the magnetic hysteresis loop in Fe-Ni/Si(100) film with induced magnetic anisotropy

The magnetic hysteresis of Fe₅₇Ni₄₃/Si(100) with magnetic anisotropy induced by an external field has been studied by Brillouin light scattering (BLS). The results are compared with those of the magneto-optic-Kerr-effect (MOKE) measurement and the vibrating sample magnetometer (VSM). The BLS results show that the sample film has strong in-plane anisotropy. The angle between the magnetization and a 4.6 G applied magnetic field H reaches a maximum value of 45° when H lies along the hard axis. The coercivity and magnetic anisotropy field for the film obtained by the BLS are compared with the values obtained by the VSM and MOKE measurement.     

Growth and magnetic behavior of bismuth substituted yttrium iron garnet nanoparticles

Crystal growth and the magnetic properties of bismuth substituted yttrium iron garnet (Bi-YIG) nanoparticles were studied with particular focus on the bismuth composition dependence of the magnetic properties of the particles and the effects of annealing on the garnet phase formation. The Bi-YIG nanoparticles of 47–67 nm in size can be chemically synthesized when they are annealed at 650–850 °C. Both the lattice constant and the magnetization of the garnet nanoparticles linearly increase when the bismuth composition in the Bi-YIG particles increases. We have found that chemically synthesized nanoparticles transform from the amorphous to the garnet phase when annealed at temperatures below 650 °C, while the onset of magnetic moment of iron in the garnet nanoparticles is observed slightly above 650 °C. According to Mössbauer effect measurements, the hyperfine fields of ⁵⁷Fe at the tetrahedral and octahedral sites in the garnet are 39 and 48 T, respectively.     

Brillouin light scattering of CoFe/IrMn-based top and bottom spin-valves

The spin-wave Brillouin light scattering (BLS) was observed from CoFe/IrMn-based bottom and top spin-valve structures. The magnitude of perpendicular magnetic anisotropy of these structures was investigated by means of BLS. The experimental spin-wave frequency was simulated using a simple model which includes crystallographic, exchange, in-plane uniaxial, and in- and out-of-plane anisotropies and takes the exchange interaction between the two ferromagnetic layers into account. This enabled us to determine, in addition to the other magnetic parameters, both in- and out-of-plane anisotropy constants near the surface. It was found that the top spin-valve is in a strong out-of-plane anisotropy whereas in-plane anisotropy is dominant for the bottom spin-valve.     

抗凝血酶Ⅲ的免疫共振散射光谱分析

在pH 7.2的Tris-HCl缓冲溶液中和聚乙二醇6000（PEG-6000）存在下,羊抗人抗凝血酶Ⅲ与抗凝血酶Ⅲ（AT-Ⅲ）发生免疫反应形成疏水性的免疫复合物微粒,导致体系的共振散射强度增强,在波长为368,491和538 nm处出现3个共振散射峰,其中491 nm处的峰最强。分别考察了pH、AT-Ⅲ和PEG-6000浓度、温育时间和温度、共存物质的影响。在选定条件下,AT-Ⅲ浓度在62.5～875 ng·mL-1范围内与491 nm处体系的散射强度呈良好的线性关系,其回归方程为ΔI_RS=62.5c+1.36,相关系数为0.996,检出限为29.4 ng·mL-1。该方法简便、灵敏和选择性好,用于人血中AT-Ⅲ含量的测定,结果满意,回收率在90.2%～108.9%之间。     

Effects of heating rate on the magneto-optical properties of bismuth-substituted yttrium iron garnet films prepared via modified metal-organic decomposition

This work investigated the effects of heating rate and annealing on the magneto-optical properties of bismuth-substituted yttrium iron garnet (Bi-YIG) thin films on glass and (111)-oriented single-crystalline gadolinium gallium garnet (GGG) substrates fabricated by metal-organic decomposition (MOD). We modified the MOD method by eliminating the pre-annealing process. We performed annealing at various temperatures to determine the optimal temperature for obtaining the Bi-YIG phase. We then annealed at the optimized temperature using various heating rates. The optimal conditions were annealing for 1 h at 750 °C at a heating rate of 30 °C/min on GGG to obtain highly crystallized fine grains. The Faraday rotation for this film was about −10.5°/μm. The optimized heating rate enhanced the magneto-optical properties due to improved crystallinity and saturated magnetization. The Bi-YIG thin films prepared by this prescribed MOD method exhibited excellent magneto-optical performance and are potential candidates for applications in optical devices.     

Y3-xBixFe5O12的晶体生长

本文讨论了Y₂O₃-Fe₂O₃-Bi₂O₃-PbO·0.2B₂O₃赝四元系相图的得出与运用;用Bi₂O₃-PbO-B₂O₃做助熔剂,获得了磁性石榴石Y_3-xBi_xFe₅O₁₂单晶(0≤x≤1.2);还论述了Bi-YIG晶体内Bi含量与助熔剂熔液成份的关系。 关键词：     

Magnetic and structural properties of Fe/Cu multilayers

Fe/Cu multilayers with Fe and Cu layers of equal thicknesses were grown by high-vacuum evaporation on Si(1 1 1) substrates at room temperature. The crystal orientation, the thickness of the elemental layers and the interplanar distances were analysed by both low- and high-angle X-ray diffraction in the θ–2θ configuration. The magnetic properties of Fe/Cu multilayers were studied by both a static and a dynamic technique, namely surface magneto-optical Kerr effect (SMOKE) and Brillouin light scattering (BLS). Longitudinal SMOKE cycles permitted us to determine the orientation of the easy axis of the magnetization and to put in evidence an appreciable in-plane magnetic anisotropy in multilayers with low periodicity and highly coherent structure. Polar loops were then used to determine the out-of-plane anisotropy fields, showing that both first- and second-order contributions are to be considered in order to reproduce the hysteresis cycle. BLS was then exploited to detect thermaly excited spin waves through inelastic scattering of light. The out-of-plane anisotropy fields evaluated by this high-frequency dynamic technique compare fairly well with the first-order values obtained by analysis of polar SMOKE hysteresis cycles.