Compact fiber optic accelerometer

A compact fiber optic accelerometer based on a Michelson interferometer is proposed and demonstrated. In the proposed system, the sensing element consists of two single-mode fibers glued together by epoxy, which then act as a simple supported beam. By demodulating the optical phase shift, the acceleration is determined as proportional to the force applied on the central position of the two single-mode fibers. This simple model is able to calculate the sensitivity and the resonant frequency of the compact accelerometer. The experimental results show that the sensitivity and the resonant frequency of the accelerometer are 0.42 rad/g and 600 Hz, respectively.     

Twin-core erbium-doped fiber amplifier with channel equalization

A twin-core erbium-doped fiber amplifier has been studied. We establish the theoretical model, propose the coupled-propagation equations, and then numerically simulate the characteristics of the amplifier. It is found that twin-core erbium-doped fiber amplifier can provide different gains for signals with different input powers and self-heal the extra channel loss between amplifying stages, thus equalizes the output signal level. The twin-core erbium-doped fiber amplifier is very suitable for the future wavelength-division-multiplexed and optical frequency-division-multiplexed fiber networks.     

Integrated fiber Michelson interferometer based on poled hollow twin-core fiber

We propose an integrated fiber Michelson interferometer based on a poled hollow twin-core fiber. The Michelson interferometer can be used as an electro-optic modulator by thermal poling one core of the twin-core fiber and introducing second-order nonlinearity in the fiber. The proposed fiber Michelson interferometer is experimentally demonstrated under driving voltages at the frequency range of 149 to 1000 Hz. The half-wave voltage of the poled fiber is 135 V, and the effective second-order nonlinear coefficient χ2 is 1.23 pm/V.     

Flextensional fiber Bragg grating-based accelerometer for low frequency vibration measurement

The intelligent structural health monitoring method,which uses a fiber Bragg grating(FBG) sensor,is a new approach in the field of civil engineering. However,it lacks a reliable FBG-based accelerometer for taking structural low frequency vibration measurements. In this letter,a flextensional FBG-based accelerometer is proposed and demonstrated. The experimental results indicate that the natural frequency of the developed accelerometer is 16.7 Hz,with a high sensitivity of 410.7 pm/g. In addition,it has a br...     

Photonic crystal fiber design for broadband directional coupling

A novel design for a broadband directional coupler based on a photonic crystal fiber is investigated numerically. It is shown that suitable index-depressing doping of the core regions in an index-guiding twin-core photonic crystal fiber can stabilize the coupling coefficient between the cores over an extremely broad (octave-spanning) frequency range.     

Polarization dependent inter-core interferences in twin-core photonic crystal fiber and its application to high temperature measurement

We investigate polarization dependent differential group modal index sensitivity to temperature in twin-core photonic crystal fiber. Characteristics of guided modes and the group modal index difference in twin-core photonic crystal fiber (TC-PCF) are numerically analyzed. The geometrical asymmetry between the two cores induces significantly reduced power coupling between two core modes and difference in their effective indices. Two cores form two effective optical paths. We also experimentally demonstrate polarization dependent differential group modal index sensitivity to the temperature. Since the TC-PCF has polarization dependent group modal index difference, TC-PCF based interferometer shows input polarization dependent free spectral range and temperature sensitivities. The effective index difference between the two core modes tends to increase when the temperature increases.     

三分量全光纤加速度检波器及数字处理系统

研制出三分量全光纤加速度检波器及其数字信号处理系统。该检波器由一个质量块，六个顺变柱体，三组迈克耳孙干涉仪光路组成。顺变柱体是检波器敏感元件中的关键部件。该检波器数字信号处理系统以TI公司的高性能数字信号处理芯片为核心，辅以必要的电路，实现了对加速度信号的高精度检测和误差信号的补偿。测试结果表明，检波器在共振频率以上有较好的频率响应，输入信号与输出信号吻合较好；检波器在共振频率以下亦有较好的频率响应。最后给出了检波器频率响应曲线。     

基于弯曲不敏感光纤的长周期光纤光栅可调谐增益均衡器

对高频CO2激光脉冲方法在弯曲不敏感光纤中写入的长周期光纤光栅的弯曲特性进行了研究，发现其谐振峰幅值对弯曲相当敏感，为普通光纤中写入的长周期光纤光栅的2．8倍，并且谐振波长和谐振峰幅值在圆周方向上呈现的对应规律与普通光纤不同．即谐振峰幅值最敏感方向所对应的谐振波长对弯曲不敏感。根据该现象，提出了一种利用调节其弯曲度来实现增益控制的可调增益均衡器方案，并进行了实验验证，该方法实用、简单。     

Directional coupling in twin-core photonic bandgap fibers

The frequency dependence of the coupling length in a twin-core photonic bandgap fiber is investigated numerically. In contrast to the case of index-guiding fibers, the coupling length exhibits a maximum if the cores are sufficiently well separated. The fiber design proposed is of interest for fabricating broadband tunable couplers.     

20～1250Hz光纤激光加速度传感系统设计

为了实现高灵敏度、宽频响应的光纤型加速度传感器,以光纤激光器作为加速度传感器的传感元件,建立了光纤激光加速度传感系统,并对该系统的传感原理、灵敏度和谐振频率等性能进行了分析和实验。采用竖直式加速度传感器结构,结构中的传感组件主要由质量块和中空的细钢管组成,光纤激光器受预应力作用后粘接在钢管内部,在加速度作用下,钢管产生的应变引起光纤激光器的应变和折射率发生改变,导致光纤激光器的出射波长随之发生改变,然后使用干涉解调技术检测出波长的动态变化,即可获得波长中包含的加速度振幅和频率信息。实验结果表明,在20~1 250 Hz频段内,竖直式光纤激光加速度传感器的灵敏度约为-126.2 d B[参考值1 rad/(μm/s~2)],频响曲线的波动幅度在±1.9 d B范围内,加速度响应动态范围为77.46~170.26 d B[500 Hz频点,参考值1μm/(s~2·Hz1/2)],加速度分辨率优于0.01 m/s~2。     

顺变柱体型全光纤加速度检波器

介绍了顺变柱体型全光纤加速度检波器的工作原理及结构设计，该检测器包括两个顺变柱体和一个质量块，两顺变柱体上都紧紧地绕着单模光纤，形成了迈克耳孙干涉仪的两个臂，两干涉臂的端面镀有高反铝膜，初步测试结果表明，检波器在共振频率以上有较好的频率响应，输入信号与输出信号吻合得较好。     

Optical refractometer based on an asymmetrical twin-core fiber Michelson interferometer

We report and demonstrate an optical refractometer based on a compact fiber Michelson interferometer. The Michelson interferometer is composed of an asymmetrical twin-core fiber containing a central core and a side core. By chemically etching a segment of the twin-core fiber until the side core is exposed, the effective index of the side core in the etched region is sensitive to the environmental refractive index, which leads to a shift of the transmission spectrum of the Michelson interferometer. The experimental results show that such a device has a refractive index resolution of more than 800 nm/refractive index unit in the range of 1.34-1.37.     

800nm波段单偏振方向上无模间色散的双芯光波导

为探究如何消除双芯光波导的模间色散,提出了一种纤芯填充高折射率溶液的双空芯光子晶体光纤,并基于全矢量有限元法进行了理论分析,获得了光纤的模式有效折射率、耦合系数、模间色散系数。研究结果表明:当纤芯所填充的溶液折射率为1.40时,光纤的y偏振方向上模间色散在800 nm传输波长处为零,理论上能够完全消除y偏振方向上模间色散导致的脉冲畸变。即,当传输光波长为800 nm时,这种光纤在y偏振方向上可以抑制模间色散,从而可以广泛用于全光开关、超短脉冲传输、光孤子传输等应用场合。     

Three-component hybrid-integrated optical accelerometer based on LiNbO_3 photoelastic waveguide

A novel three-component hybrid-integrated optical accelerometer based on LiNbO3 photoelastic waveguide is presented. The photoelasitcity of LiNbO3 due to three-dimensional stress states is obtained analytically. We analyze the level of sensitivity to cross-axis accelerations which is a very important parameter for three-component accelerometer. Theoretically, the designed three-component hybrid-integrated optical accelerometer has a transverse sensitivity ratio （TSR） of zero. The sensor has a high natural frequency of 3.5 kHz and a linear broad working freauency.     

采用DDS的近场扫描光学显微镜探针-样品的纳米距离检测

近场扫描光学显微术中, 近场距离的检测和控制是需要解决的核心技术之一. 本文研究了基于DDS驱动的压电传感器, 在一个压电陶瓷片上, 电极被分成相同的两部分, 分别用于振动驱动和振幅检测. 近场扫描的光纤探针固定于此压电陶瓷片上. 振动驱动信号采用DDS, 在样品的远场时, 可以通过频率扫描得到误差在0.006 Hz以内的压电陶瓷片谐振频率驱动信号, 而当光纤探针处于样品的近场距离之内时, 压电陶瓷片的谐振频率偏离驱动信号频率, 振幅明显减小, 从而检测出近场距离. 高精度振动驱动源DDS和高灵敏度压电传感器的采用提高了检测灵敏度和工作稳定性.     

采用GRIN透镜的数字式光纤加速度计系统设计

为使测量加速度计的传感器小型化、不受电磁干扰 ,根据GRIN透镜在 1 / 4波节处具有入射光线与出射光线成中心对称的特性[1 ] ,首次提出并研制了采用GRIN透镜的微型光纤加速度计。闭环负反馈电路设计技术被应用于该加速度计中 ,使之成为一个具有调宽脉冲再平衡性能的新颖加速度测量系统。通过对该系统进行数字仿真和精度定量分析 ,结果表明 ,该光纤加速度计具有测量线性范围宽、精度高的特点 ,可广泛应用于惯性测控系统中     

对弯曲不敏感的长周期光纤光栅传感器

发现了用高频CO₂激光写入的长周期光纤光栅的谐振波长对弯曲灵敏度在圆周的不同方向上呈现周期性,且在两个特定的对称方向上对弯曲不敏感(即弯曲曲率达到1.1m^-1,谐振波长仅漂移-0.018nm).据此提出新型对弯曲不敏感的传感器和可调灵敏度弯曲传感器的设计方案,可望从根本上解决长周期光纤光栅在测量中存在的温度、应变或折射率与弯曲之间的交叉敏感问题.     

Long-period-grating-assisted optical add-drop filter based on mismatched twin-core photosensitive-cladding fiber

A noninterferometric optical fiber add-drop channel filter based on a mismatched twin-core photosensitive-cladding fiber and long-period fiber grating is demonstrated. With assistance from the fiber grating, co-directional spectrally selective cross coupling between the two cores can be realized with an efficiency of 90%.     

一种新型温度自补偿高灵敏度折射率计

基于高频CO2激光脉冲写入的新型超长周期光纤光栅(ULPFG),提出了一种可实现温度自补偿的新型高灵敏度折射率计。理论与实验表明,新型超长周期光纤光栅不同闪耀阶次谐振峰对外界折射率与温度变化的灵敏度各自不同,特别的是,该光栅存在对外界折变不敏感的谐振峰,测量中除了可以利用该峰实现温度同时测量外,还可以补偿另一个测量折变的谐振峰因温度变化带来的测量误差。该折射率计具有制作简单、成本低、强度好,灵敏度高等优点,当外界折射率在1.43~1.45范围内变化时,其折射率测量灵敏度可达每单位折射率240 nm,在实际工业应用中具有较大的潜在实用价值。     

A Fiber Optic Non- Contact Accelerometer

A novel non-contact fiber optic accelerometer is presented. Two laser beams that have passed through two different lengths of feed fibers are launched to the same moving target. The frequency of each beam is Doppler shifted by movement of the target. The frequency shift of the laser beam corresponds to the velocity of the target at the time of launch. The difference in launching time due to the difference in feed fiber lengths samples the velocities of the target at times spaced by the differential arrival times of the laser beams. Two return passes of the reflected light are also made different so that the light passed through the shorter feed fiber is steered to the longer return fiber by means of a combination of A/4 plate and polarization beam splitter (PBS). This arrangement of equalizing the total paths relieved a stringent requirement of the coherency of the laser. Two reflected light beams are mixed and the beat frequency corresponds to the difference in the Doppler shift frequency at two different times of arrival of the launcher. An accelerometer based upon this principle was constructed and its performance was examined using a sinusoidally vibrating hydrophone as a target. Features of such an accelerometer are reduction in the coherency requirements of the light source and simpler amplification of the signal using heterodyne detection.On leave of absence from Department of Optical Engineering, Zhejiang University, HangZhou, China 310027