可调谐半导体激光器的瞬时光谱测量方法研究

可调谐半导体激光器在调谐过程中的瞬时光谱特性,如瞬时的波长、调谐率、功率、线型和线宽等参数影响着以激光器为光源的光学测量和光相干通信系统的精度。然而,能够同时测量这些瞬变参数的技术至今未见报道。提出了一个基于时频分析的测量半导体激光器在调谐过程中瞬时光谱参数的方法,利用一个短时延外差测量系统,利用激光器瞬时光谱参数与差拍信号瞬时参数的关系,最终获得了半导体激光器在连续电流调谐过程中的瞬时光谱。测量系统采用了10 cm光程差的Mach-Zehnder干涉仪,调谐电流是幅度为20~120 mA、频率是1 kHz的锯齿波,差拍信号可视为直流信号、载波信号与噪声的叠加,按照短时延相干光测量原理,差拍信号中的直流分量幅度的大小反映了激光器输出光信号的功率;载波信号是一种多项式相位信号,由其频率可以推算激光器输出光谱的中心频率或波长;噪声信号则与激光器输出光谱的线型和线宽相关,通过对噪声信号进行时频分析,可以获知激光器在连续电流调谐过程中每一时刻或每个电流下的瞬时线型、线宽。采用了趋势局部均值分解方法对差拍信号进行了准确分离,并对分离信号分别进行处理,同时获知了半导体激光器在调谐过程中的瞬时输出光功率、光波长、调谐率及线型、线宽。在去掉弛豫部分后截取的整周期差拍信号对应的调谐电流60~115 mA变化范围内,半导体激光器(FRL15DDR0A31-18950, Furukawa)瞬时输出光功率变化范围是5.16~10.6 mW,瞬时光波长变化范围为1 579.2~1 579.6 nm;激光器的瞬时调谐率在0.004 8~0.011 5 nm·mA-1范围内单调变化;线宽是852.55~954.95 kHz,呈非线性随机分布。基于短时延、局部均值分解和时频分析方法的瞬时光谱参数测量系统可以准确得到各瞬时光谱参数,测量结果与激光器的静特性相符,且测量系统结构简单,使我们更深入地理解激光器的工作原理,具有广阔的应用前景。     

激光光源线宽对外差探测性能的影响

本文根据统计理论分析了激光线宽对外差探测结果的影响, 并讨论了激光线宽对杨氏干涉条纹对比度的影响. 本文基于解析结果做了数值仿真, 所得结果表明激光线宽增加时, 外差探测方式仍可以检测到中频信号, 但在线宽较大时, 受噪声影响无法准确地提取到中频频率. 为验证理论分析结果, 使用线宽为1 MHz的激光光源进行了8.1 km外场实验, 实验结果与数值分析结论一致, 即不会因为线宽增加而无法检测到中频信号. 文中所得结论对于外差探测光源的选择有重要指导意义, 因此根据测量目标的特性和测量要求, 可按照文中结论评估光源的线宽指标.     

Switchable instantaneous frequency measurement by optical power monitoring based on DP-QPSK modulator

We propose and analyze an instantaneous frequency measurement system by using optical power monitoring technique with improved resolution. The primary component adopted in the proposal is a dual-polarization quadrature phase shift keying (DP-QPSK) modulator which is used to modulate the microwave signal that has a designed time delay and phase shifting. The generated optical signal is sent to polarization beam splitter (PBS) in DP-QPSK modulator. Owing to the complementary transmission nature of polarization interference introduced by PBS, the frequency information is converted into the optical power and the relationship between the amplitude comparison function (ACF) and microwave frequency to be measured is established. Thus, the frequency of the microwave signal can be easily measured through monitoring the optical powers of the two output ports of the PBS. Furthermore, by adjusting the direct current (DC) biases of the DP-QPSK modulator instead of changing the electrical delay, the measurement range and resolution can be switched. In this paper, the basic principle of the instantaneous frequency measurement system is derived in detail, and simulation has been performed to investigate the resolution, the measurement range, and the influence of imperfection devices. The proposed scheme is wavelength-independent and its measurement range is switchable, which can avoid the laser wavelength drifting problem and thus greatly increasing the system flexibility.     

CCD噪声标定及其在边缘定位中的应用

成像过程中的CCD噪声将给图像测量结果带来误差,因此能否有效地抑制这些噪声是提高测量精度的关键。分析了CCD暗电流噪声和随机噪声的特性,并针对各自特性提出了相应的噪声标定技术以及抑制方法。结合精密图像测量任务,分别研究了暗电流噪声和随机噪声对一维边缘定位、结构光相移法相位提取的影响。通过仿真和实验,比较了噪声抑制前后的测量结果,结果表明,噪声抑制后边缘定位精度有很大的提高,证实了该CCD噪声标定技术和抑制方法的有效性和必要性。     

200 km沙漠链路高精度光纤时频传递关键技术研究

针对沙漠环境实地链路存在的温度变化大、室外风力、地表振动等多种复杂噪声来源,通过对系统反馈补偿带宽、反馈补偿强度、光功率等时频传递系统关键参数的优化配置,研究了不同反馈补偿参数下复杂链路噪声的有效抑制技术.全链路的频率传递稳定度8×10~(-14)@1s,1×10~(-16)@1000 s,千秒尺度下时间信号传递的时间方差仅为1.2 ps.实现了氢钟信号在200 km量级沙漠环境实地链路的无损传输.该验证实验在基于短基线干涉测量的卫星测轨系统中发挥了重要作用.     

基于宽带光源和自外差检测的布里渊光时域反射温度传感系统

为简化系统结构、减小相干瑞利噪声对系统性能的影响,提出了一种采用宽带光源的瑞利和布里渊散射自外差检测布里渊光时域反射温度传感系统.分析了瑞利和布里渊自外差检测原理,研究了布里渊频移和自外差信号功率与光纤温度和应变的关系.设计并搭建采用宽带光源的自外差检测布里渊光时域反射温度传感系统,获得了常温下沿光纤分布的自外差信号功率谱及不同温度时加温段光纤的功率谱,验证了布里渊频移和自外差信号相对功率变化随温度的线性增加关系.通过实验数据获得的布里渊频移和相对功率变化的温度系数分别为1.07±0.01MHz/℃和(0.37±0.09)%/℃.本文的研究结果为基于瑞利和布里渊自外差检测布里渊光时域反射传感系统的温度和应变同时测量提供了理论和实验依据.     

High-order spectra-based deconvolution of ultrasonic NDT signals for defect identification

In ultrasonic nondestructive testing (NDT) of materials, pulse-echo measurements are masked by the characteristics of the measuring instruments, the propagation paths taken by the ultrasonic pulses, and noise. This measured pulse-echo signal is modeled by the convolution of the defect impulse response and the measurement system response, added to noise. The deconvolution operation, therefore, seeks to undo the effect of the convolution and extract the defect impulse response which is essential for defect identification. In this contribution, we show that the defect ultrasonic model can be formulated in the higher-order-spectra (HOS) domain in which the processing is more suitable to unravel the effect of the measurement system and the additive Gaussian noise. In addition, a new technique is developed to faithfully recover the impulse response signal from its HOS. Synthesized ultrasonic signals as well as real signals obtained from artificial defects are used to show that the proposed technique is superior to conventional second-order statistics-based deconvolution techniques commonly used in NDT.     

基于噪声免疫腔增强光外差分子光谱技术实现光纤激光器到1530.58 nmNH_3亚多普勒饱和光谱的频率锁定

噪声免疫腔增强光外差分子光谱技术(NICE-OHMS)由于结合了频率调制光谱与腔增强光谱两种技术,不仅可以将激光耦合到高精细度谐振腔大幅提高腔内功率,还可以实现低气压样品气体的高灵敏测量,因此基于该技术可以实现分子吸收线的饱和,获得亚多普勒光谱,从而能作为激光频率锁定的参考.本文基于光纤激光器的NICE-OHMS技术,将光纤激光器频率锁定到NH3的亚多普勒吸收线上.首先分析了基于Pound-Drever-Hall和DeVoe-Brewer技术实现激光到腔模和调制频率到腔自由光谱区频率锁定的性能,之后在腔内气压为70 mTorr条件下,测量了半高全宽为2.05 MHz的NH3亚多普勒信号,最后将1.53μm的光纤激光器频率锁定到该亚多普勒吸收线上,相对频率偏差为16.3 kHz,阿伦方差结果显示,136 s积分时间下频率稳定度达到1.6×10~(-12).     

Next Step of Non-invasive Glucose Monitor by NIR Technique from the Well Controlled Measuring Condition and Results

Although non-invasive glucose measurement techniques based on near-infrared (NIR) spectroscopy have been interested for over 20 years, a reliable non-invasive glucose monitoring method has not been established yet. Many hurdles are remained to be solved to extract extremely small glucose information from the complicated NIR spectra. In addition, there are also some ambiguous time-dependent physiological processes, which make the explanation of the model more difficult especially in the universal calibration. In this paper, the optical consideration in instrument to improve the SNR is discussed first, which is a critical way to detect small analyte signal. Then an optical measuring conditions reproducible system is used to reduce the noise from human-spectrometer interface. And an optical probe is designed according to the Monte Carlo simulations to measure the dermis selectively to eliminate the noise from human tissue. Finally, with the well-controlled measuring conditions, the in vivo result of single person using the leave one out cross validation within the single day is quite satisfactory. However, the validation results using the validation set from different day are not so good. Further research and extensive model validations are needed to determine if the model is truly based on the glucose information.     

Simulation and evaluation of phase noise for optical amplification using semiconductor optical amplifiers in DPSK applications

A thorough simulation and evaluation of phase noise for optical amplification using semiconductor optical amplifier (SOA) is very important for predicting its performance in differential phase-shift keyed (DPSK) applications. In this paper, standard deviation and probability distribution of differential phase noise at the SOA output are obtained from the statistics of simulated differential phase noise. By using a full-wave model of SOA, the noise performance in the entire operation range can be investigated. It is shown that nonlinear phase noise substantially contributes to the total phase noise in case of a noisy signal amplified by a saturated SOA and the nonlinear contribution is larger with shorter SOA carrier lifetime. It is also shown that Gaussian distribution can be useful as a good approximation of the total differential phase noise statistics in the whole operation range. Power penalty due to differential phase noise is evaluated using a semi-analytical probability density function (PDF) of receiver noise. Obvious increase of power penalty at high signal input powers can be found for low input OSNR, which is due to both the large nonlinear differential phase noise and the dependence of BER vs. receiving power curvature on differential phase noise standard deviation.     

基于重采样技术的调频连续波激光绝对测距高精度及快速测量方法研究

调频连续波激光测距方法可以实现高精度的大尺寸绝对距离测量, 且测量过程无需合作目标, 在大空间坐标精密测量领域有很高的研究价值. 而如何提高测量分辨率和实用化一直是近年来调频连续波激光绝对测距研究的热点. 本文研究了调频连续波激光测距的原理, 基于双光路调频连续波激光测距系统, 提出了通过信号拼接提高测量分辨率的信号处理优化方案, 该方案可以提高测距分辨率, 且可以降低对激光器的性能要求; 提出了可实现高速测量的简易测量方法. 设计加工了双光路光纤调频连续波激光测距系统, 利用该系统进行了测距分辨率及测距误差标定实验, 实验结果表明: 优化方案可以有效地提高测量分辨率和测量效率, 在26 m测量范围内, 测距分辨率达到了50 μm, 测距误差不超过100 μm; 快速测量方案有较高实用价值.     

Novel model of FM-noise conversion in a UMZI using RF external phase modulation of lasers: Theoretical and experimental results

In this paper, we propose and demonstrate a new and original model for theoretical calculation and experimental measurement of the noise power spectral density (NPSD) in phase-modulated optical links. The phase modulation is operated in the RF frequency range by an external phase modulator. The NPSD is derived for the first time in interferometric systems, by considering all effects such as the 1/f FM noise of the laser and white noise applied to light from a 1550 nm DFB laser, with phase modulation. The results show for the first time the influence of the phase modulation index, modulation frequency and interferometric delay in the phase-to-intensity noise conversion. The experimental and simulation results of conversion of FM-noise to intensity noise in an optical link by considering the external RF phase modulation are shown with good agreement.     

Polarization maintaining optical fiber multi-intruder sensor

In this paper, an optical fiber multi-intruder sensor based on polarization maintaining optical fiber (PMF), without any interferometric fiber loop, is introduced. To map the local coordinates of intruders on the beating spectrum of the output modes, radiation from a ramp frequency modulated laser is injected at the input of PMF optical fiber sensor. It is shown that the local coordinates and some characteristics of intruders can be obtained by the measurement of the frequencies and amplitudes of the output mode beating spectrum. Generally the number of beating frequencies is more than the number of intruders. Among the beating frequencies, a group with maximum signal to noise ratio is chosen. The short Fourier denoising method is employed to increase the sensor resolution. Because the output signal is the superposition of finite numbers of discrete frequencies this method is a powerful tool for denoising even for negative signal to noise ratio.     

光纤干涉位移传感器相位估计的一种精确方法

应用信号处理有关技术提出了一种光纤干涉位移传感器相位估计的方法,可以解决很大范围的不等幅、周期非均匀、带噪干涉信号条纹的精确计数问题。分析了此方法的适用范围及估计精度。对于１０ｄＢ信噪比的系统来说,位移在０．３ｍｍ以内的测量精度可达到λ／１００。     

超短时延测量DFB激光器的动态线宽

激光器调谐过程中的动态线宽是非常重要的参数, 然而, 当前各种测量方法得到的都是激光器稳定状态下的静态线宽. 本文提出一种对干涉拍信号进行基于局部均值分解的时频分析进而获取激光动态线宽的方法, 通过仿真信号验证了这种时频分析方法提取瞬时相位噪声的有效性; 构建实验系统, 利用10cm路径差产生约0.5ns的超短时延, 提取相位噪声的时频分布, 首次得到了分布反馈半导体激光器在脉冲工作模式下的动态线宽. 关键词： 超短时延 动态线宽 局部均值分解 时频分布     

Dark fringe operation and noise reduction with optical subtraction approach and power allocation

We demonstrate a technique to achieve the reduction of excess noise with dark fringe operation by optical subtraction and power allocation strategy. By performing the subtraction in optical way, the excess noise resulted from the photocurrent is eliminated and the phase information can be extracted with single photoreceiver. Meanwhile, by allocating more optical power to the probe beam, the DC background and the signal amplitude of the photocurrent become very small simultaneously so that the dark fringe operation is achieved. We compare the spectral distributions resulted from the proposed technique with that from the widely employed balanced detection and the modified balanced detection techniques which both are based on electronic subtraction. It is found that the experimental results closely agree to the theoretical predictions.     

低频标准真空涨落的测量

采用自平衡零拍方案, 对低频段的标准量子真空涨落进行了测量. 实验确定了该系统的饱和光功率约为3.2 mW. 在10 Hz–400 kHz的频率范围内, 系统的共模抑制比平均为55 dB, 在100 Hz处高达63 dB, 对激光经典技术噪声具有很强的抑制作用. 当入射光功率为400 μ W 时, 真空涨落噪声达到11 dB. 此低频量子真空噪声探测系统可广泛应用于量子计量和量子光学等研究领域.     

基于光热效应的显微光谱技术在单粒子检测中应用和发展

高灵敏度的单粒子检测技术是纳米粒子在生物医学、化学、光电子等领域应用的前提条件。常见的单粒子检测技术主要包括基于粒子的荧光、拉曼、散射和吸收等信号而发展起来的光学显微成像及光谱技术。其中,拉曼光谱和荧光光谱技术主要适用于一些具有拉曼活性的分子/粒子或可发光的荧光分子或粒子,然而即使对于荧光效率高的有机染料分子和半导体纳米粒子,固有的光漂白和blinking现象也对单粒子探测形成了挑战。散射光谱测量是应用于单粒子检测的另外一种方法,从理论上讲,由于瑞利散射随着尺寸的减小而呈六次方减弱的趋势,在细胞或生物组织内,小尺寸粒子的散射信号很难从背景散射噪声中分离出来。众所周知,介质吸收激发光后会引起介质内的折射率变化,进而在光加热区附近出现折射率的梯度分布,称为光热效应(photothermal effect)。基于粒子光热效应的光学显微成像和光谱测量技术具有信号灵敏度高、无背景散射、原位和免标记等优点,在单粒子检测领域展现了良好的应用潜力。综述了近年来基于光热效应的显微光谱技术在单粒子检测中应用和研究发展,首先介绍了光热效应的测量原理;接着分别讨论了光热透镜测量技术、微分干涉相差测量技术和光热外差测量技术的实验装置,比较了各种测量技术的信噪比、灵敏度、分辨率等特点,并且介绍这些测量技术在单粒子检测中的应用研究进展;接着,论述了近年来研究人员在提高光热显微测量的信噪比、改善动态测量性能以及在红外波段拓展等方面的最新研究成果;最后,简单总结了光热测量技术在单粒子检测领域所面临的挑战。     

Measurement of sound field in cavitating media by an optical fibre-tip hydrophone

A fibre-optic technique was applied to measure the sound field in an ultrasonic cleaning vessel under practical conditions. A metal-coated fibre-tip is used as a sensor and a heterodyne interferometer detects the change in the optical path resulting from the movement of the fibre-tip in the sound field. Spectrally resolved sound field parameters such as the fundamental, the subharmonic or cavitation noise are extracted from the measurements and compared with results obtained by a piezo-electric hydrophone. It was found that the fibre sensor provides a signal related to the velocity in the sound field, but the information about cavitation-related parameters is similar to the information for pressure sensing techniques. The fibre-optic sensors have a uniquely high spatial resolution and the sound detection process is strongly influenced by single cavitation events close to the small fibre-tip. This paper shows that fibre-tip sensors are an alternative to common hydrophone techniques. They can open up new possibilities for measurement problems for which so far no solution exists, in particular when a high spatial resolution is required or when the measurement site is small.     

频域反射法光纤延时精密测量

本文提出了一种应用于光纤延时系统中实现光纤延时精密测量的新方法,用以提高光纤延时测量的精度和准确性.该方法以1064 nm激光调制信号作为光源,通过测量回波信号的幅值和相位信息得到被测通道的频率响应,采用快速傅里叶逆变换得到被测目标的延时信息,实现光纤延时测量.本文通过理论分析和延时测量实验对频域反射法与传统的时域测量方法进行对比,使用频域反射法在调制频率范围10—200 MHz,采样频率间隔0.5 MHz的实验条件下,实现了3.3 ps延时测量分辨率,并证明了该方法具有比时域方法更高的测量精度,测量结果的准确性更好.