高温处理对碳载吡啶钴催化氧还原性能的影响

利用碳黑(Vulcan XC-72R) 中加入硫酸钴和吡啶(Py)作为催化剂前躯体, 经溶剂分散热处理构建了一类新型的高效氧还原CoPy/C复合催化剂. 运用循环伏安法和旋转圆盘电极(RDE)技术研究了不同温度(600~900 ℃)处理CoPy/C催化剂在碱性介质中对氧还原的电催化性能. 结果表明, 热处理能显著提高CoPy/C的催化活性, 活性次序为800 ℃>900 ℃>600 ℃>未处理. 其中800 ℃处理的15%Co25%Py/C(质量分数)复合催化剂表现出最佳的氧还原催化性能, 以其制备的气体扩散电极在3.0 mol/L KOH 电解质溶液(O₂气氛)中的半波电位为-0.069 V(相对于标准可逆氢电极), 起峰电位为0.026 V, 同时表现出明显的极限扩散电流. 利用透射电镜、 能谱分析和X射线衍射技术对催化剂的微观形貌、 颗粒大小和活性位结构的研究结果表明, 所制备的碳黑负载吡啶钴催化剂(15%Co25%Py/C)平均粒径为17 nm, 经800 ℃处理后吡啶结构发生了坍塌, 形成了其它价态的钴氧化合物、 硫化物和单质钴, 并协同吡啶中的氮对氧起催化还原作用. RDE结果表明, O₂在CoPy/C催化剂上的反应动力学主要通过4e^-过程还原成H₂O.     

CoPy/C催化剂应用碱性介质氧还原催化的电化学性能

利用碳黑（Vulcan XC-72R）中加入硫酸钴和吡啶（Py）作为催化剂前驱体,经溶剂分散热处理构建了一类新型的高效氧还原CoPy/C复合催化剂.并运用循环伏安法（CV）和旋转圆盘电极（RDE）技术研究了不同Co含量的CoPy/C催化剂在碱性介质中对氧还原的电催化活性.结果表明:Co的存在对氧的催化剂活性位的形成有重要影响,800℃下所制备的10%Co30%Py/C（质量分数）复合催化剂表现出最佳的氧还原催化活性.以其制备的气体扩散电极在3.0 mol·L^-1KOH电解质溶液（O₂气氛）中0.014 V（相对于标准氧电极（RHE））即可产生明显的氧还原电流.同40%Py/C相比,10%Co30%Py/C催化氧还原的起峰电位正移了71 mV,同时表现出明显的极限扩散电流.在-0.16 V时电流密度达到最大值,电流密度为1.0 mA·cm^-2,半波电位在-0.07 V.透射电镜分析表明所制备的碳黑载吡啶钴（10%Co30%Py/C）催化剂平均粒径为20 nm.     

氮掺杂碳纳米管负载Co3O4氧还原电催化剂的制备与性能

以碳纳米管(CNT)为原料,通过负载维生素B₁₂,简单热解得到了一种氮掺杂碳纳米管(N/CNT)负载低含量Co₃O₄纳米颗粒的氧还原电催化剂(Co₃O₄@N/CNT)。得益于均匀分散的Co₃O₄纳米颗粒以及氮掺杂,Co₃O₄@N/CNT表现出了优异的氧还原催化性能,其半波电位达到了0.844 V(vs RHE),超越了商业Pt/C(0.820 V(vs RHE))。与Pt/C相比,基于Co₃O₄@N/CNT组装的锌-空气电池表现出了更优的放电性能和循环稳定性。     

锌掺杂提高LiNi1/3Co1/3Mn1/3O2正极材料的电化学稳定性

通过共沉淀法与固相法相结合制备了掺锌的高稳定性Li(Ni_1/3Co_1/3Mn_1/3)_1-xZn_xO₂ (x=0, 0.02, 0.05)正极材料. 循环伏安(CV)曲线表明Zn掺杂使氧化峰与还原峰的电势差减小到0.09 V, 电化学阻抗谱(EIS)曲线表明Zn掺杂使电极的阻抗从266 Ω减小到102 Ω. Li⁺嵌入扩散系数从1.20×10^-11 cm²·s^-1增大到 2.54×10^-11 cm²·s^-1. Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以0.3C充放电在较高的截止电压(4.6 V)下比其他两种材料的电化学循环性能更稳定, 其第二周的放电比容量为176.2 mAh·g^-1, 循环100周后容量几乎没衰减; 高温(55 °C)下充放电循环100周, 其放电比容量平均每周仅衰减0.20%, 远小于其他两种正极材料(LiNi_1/3Co_1/3Mn_1/3O₂平均每周衰减0.54%; Li(Ni_1/3Co_1/3Mn_1/3)_0.95Zn_0.05O₂平均每周衰减0.38%). Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以3C充放电时其放电比容量可达142 mAh·g^-1, 高于其他两种正极材料. 电化学稳定性的提高归因于Zn掺杂后减小了电极的极化和阻抗, 增大了锂离子扩散系数.     

碳载体预处理对CoTMPP/BP电催化剂氧还原性能的影响

采用微波加热合成法制备了CoTMPP/BP电化学氧还原催化剂。采用旋转圆盘电极(RDE)研究了BP2000碳载体经30% H₂O₂或6 mol·L^-1 HNO₃化学预处理后对催化剂氧还原催化活性的影响，并且在PEM燃料电池工作站上测试了不同CoTMPP/BP催化剂的燃料电池单电池性能。结果表明，碳载体经过化学预处理后催化剂性能有显著的提高，并且30% H₂O₂处理效果更好。采用IR、XRD和XPS进一步分析了载体化学预处理对催化剂活性影响的机理：IR结果表明预处理后载体表面羟基(-OH)等含氧基团增多；XRD分析表明900℃热处理后催化剂中有Co₃C(101)和金属态Co(111)结构出现；XPS分析表明碳载体预处理后N原子表面浓度以及组分N1和Co^Ⅲ相对比例升高，有利于Co-N4-C活性位的形成，然而组分N1，O1s Co^Ⅲ和Co^Ⅱ的结合能(BE)有所下降。     

Al含量对Pt-SO2-4 /ZrO2-Al2O3固体超强酸催化

通过向SO^2-₄ /ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和稳定性的Pt-SO^2-₄ /ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂性能的影响; 并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征. 结果表明, Al能够提高ZrO₂的晶化温度, 抑制硫的分解, 增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃含量(质量分数, w)为5.0%时, Pt-SO^2-₄ /ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最好, 在100 h内异戊烷收率可稳定在52.0%以上, 选择性在98.2%以上.     

SO42-/SnO2-Fe2O3固体酸催化下的环酮Baeyer-Villiger氧化反应及缩合反应

采用共沉淀的方法制备了不同Fe 掺杂量的SO₄^2-/SnO₂-Fe₂O₃固体超强酸催化剂. 利用傅里叶变换红外(FTIR)光谱, 粉末X射线衍射(XRD), N₂吸附-脱附实验(BET), 热重(TG)分析和扫描电镜(SEM)等方法对样品进行了表征. 考察了所得催化剂对4-叔丁基环己酮与乙二醇缩合反应的催化性能. 实验结果表明, 与未经过掺杂改性的SO₄^2-/SnO₂固体酸催化剂相比, 改性后催化剂的催化性能得到了改善. 研究了以Fe/Sn 摩尔比为0.5的SO₄^2-/SnO₂-Fe₂O₃固体酸为催化剂, 部分醛酮类化合物与乙二醇及1,2-丙二醇的缩合反应. 考察了反应时间、催化剂用量等因素对反应的影响. 同时, 将所得催化剂应用于环酮Baeyer-Villiger 氧化反应中, 催化剂表现出良好的催化活性, 且催化剂具有一定的循环使用性.     

Ni2+在γ-Al2O3上的分散状态及负载型Ni/γ-Al2O3催化剂的α-蒎烯加氢活性

用X-射线衍射(XRD)、紫外-可见漫散射光谱(UV-Vis DRS)、程序升温还原(TPR)、CO化学吸附和微反测试等方法研究了Ni²⁺在γ-Al₂O₃上的分散状态和负载型Ni/γ-Al₂O₃催化剂的α-蒎烯加氢催化活性。结果表明，当Ni²⁺负载量远低于其在γ-Al₂O₃载体表面分散容量时，Ni²⁺优先嵌入载体表面四面体空位，随着Ni²⁺负载量的增加，嵌入载体表面八面体空位Ni²⁺的比例增大。由于八面体Ni²⁺易被还原为金属态Ni⁰，NiO/γ-Al₂O₃样品的还原度随Ni²⁺负载量的增加而大幅度地增加，经氢还原所得Ni/γ-Al₂O₃催化剂的CO吸附量和α-蒎烯加氢催化活性大幅度增加。对La₂O₃助剂的作用进行了研究，结果表明分散在γ-Al₂O₃上的La³⁺物种可阻止Ni²⁺嵌入γ-Al₂O₃表面四面体空位，增大了八面体Ni²⁺物种所占比例，提高了催化剂的还原度，故Ni-La₂O₃/γ-Al₂O₃催化剂催化活性高于Ni/γ-Al₂O₃催化剂。     

Zr0.5Ti0.5O2的添加对超临界裂解RP-3催化剂性能的影响

采用共沉淀法制备了Zr_0.5Ti_0.5O₂载体材料,将其掺杂在CeO₂-Al₂O₃ (CA)基催化剂中, 并对其催化活性进行了超临界裂解测试, 采用全自动吸附仪、X射线衍射(XRD)、透射电镜(TEM)、程序升温脱附(TPD)等方法对催化剂进行了表征. 实验结果表明, 催化剂能够明显降低裂解反应的温度, 600 ℃ CA基催化剂产气率是热裂解的2.8倍, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂是热裂解的4.0倍, 650 ℃时, 掺杂Zr_0.5Ti_0.5O₂载体材料的CA基催化剂热沉提高了0.55 MJ·kg^-1. BET结果表明, 掺杂Zr_0.5Ti_0.5O₂载体后催化剂出现双孔结构, 部分小孔的出现使得乙烯的选择性提高; NH₃-TPD结果表明, 掺杂Zr_0.5Ti_0.5O₂载体材料后, 催化剂强酸位的酸量增加了4.0倍,催化剂表现出更强的表面酸性和更集中的强酸酸中心密度, 有利于裂解多产烯烃.     

水相锌二次电池正极材料V2O5/C的电化学性能研究

采用溶胶－凝胶法合成了一种V₂O₅/C复合材料.扫描电镜（SEM）和红外光谱（FTIR）分析表明,这是一种外层V₂O₅胶体包覆内层乙炔分子的多孔复合材料.以V₂O₅/C作正极,锌片为负极,Zn(ClO₄)₂溶液为电解质组成水相锌二次电池,采用循环伏安（CV）和电化学阻抗谱（EIS）等方法研究发现:V₂O₅:C质量比为1:1时电极具有最好的电化学性能,电池开路电压达1.64 V; Zn^2＋能分别在1.01 V和1.26 V处分步嵌入V₂O₅/C结构中A、B两种位置,其嵌入电流密度峰值最高可达70 mA•g^－1,并且具有较好的循环充放电性能;在一定放电深度下,V₂O₅/C电极反应速率受Zn^2＋的扩散过程控制.     

Electronic Configuration Regulation by N-Doped MXenes Boosting Electrocatalytic Performance of Cobalt Phthalocyanine

The precise control of electronic configurations of catalytic sites via molecular engineering is significantly desirable for boosting electrocatalytic activity. We reported a new-type composite electrocatalyst with cobalt phthalocyanine supported on N-doped MXene nanosheets (N-MXene/CoPc) through a self-assembly process. Beneficial from the joint action of N sites participation and axial coordination, N-MXene/CoPc exhibits a high ORR activity with positive onset potential (E_onset=0.98 V vs. RHE) and half-wave potential (E_1/2=0.863 V), which is superior over the pristine CoPc (E_1/2=0.72 V) and the composite with undoped MXene as support (MXene/CoPc, E_1/2=0.771 V). Additionally, N-MXene/CoPc exhibits an excellent durability with only 8.5 % attenuation after 25000 s of continuous i-t test, while a more obvious decay 18.6 % for 20 wt.% Pt/C. This work not merely reported a robust ORR catalyst, but more provides a reasonable design strategy for nonnoble-metal catalysts through catalyst-support interactions.     

ZIF67衍生硫化钴/多孔碳复合催化剂的制备及其电催化性能

采用离子交换法与热处理相结合的方法,以ZIF67为前驱体,硫代乙酰胺为硫源,制备出硫化钴/多孔碳(CoS/C)复合催化材料,并探讨了硫化时间对复合催化剂的形貌、结构及其氧还原(ORR)性能的影响。采用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射仪(XRD)、N2吸附-脱附测定仪、X射线光电子能谱分析(XPS)、拉曼光谱仪(Raman)和旋转圆盘电极(RDE)技术表征催化剂的物理特征和电催化性能。研究结果显示,在碱性条件下该复合催化剂具有与20%(w/w)的商业Pt/C催化剂相媲美的ORR活性,其半波电位仅比Pt/C催化剂低31 mV。随着硫化时间的增加,硫化钴颗粒逐渐增大,催化剂中碳材料的无序程度出现先减小后增大的趋势。在硫化时间为10 min时,复合催化剂在0.1 mol·L-1KOH中表现出良好的电催化活性,且在ORR过程中复合催化剂的平均转移电子数可达到3.72,接近于4,说明氧气在该催化剂表面发生的是四电子转移过程。     

Synthesis of dual-doped non-precious metal electrocatalysts and their electrocatalytic activity for oxygen reduction reaction

The pyrolyzed carbon supported ferrum polypyrrole(Fe-N/C) catalysts are synthesized with or without selected dopants, p-toluenesulfonic acid(TsOH), by a facile thermal annealing approach at desired temperature for optimizing their activity for the oxygen reduction reaction(ORR) in O2-saturated 0.1 mol/L KOH solution. The electrochemical techniques such as cyclic voltammetry(CV) and rotating disk electrode(RDE) are employed with the Koutecky-Levich theory to quantitatively obtain the ORR kinetic constants and the reaction mechanisms. It is found that catalysts doped with TsOH show significantly improved ORR activity relative to the TsOH-free one. The average electron transfer numbers for the catalyzed ORR are determined to be 3.899 and 3.098, respectively, for the catalysts with and without TsOH-doping. The heat-treatment is found to be a necessary step for catalyst activity improvement, and the catalyst pyrolyzed at 600℃ gives the best ORR activity. An onset potential and the potential at the current density of-1.5 mA/cm2 for TsOH-doped catalyst after pyrolysis are 30 mV and 170 mV, which are more positive than those without pyrolized. Furthermore, the catalyst doped with TsOH shows higher tolerance to methanol compared with commercial Pt/C catalyst in 0.1 mol/L KOH. To understand this TsOH doping and pyrolyzed effect, X-ray diffraction(XRD), scanning electron microscope(SEM) and X-ray photoelectron spectroscopy(XPS) are used to characterize these catalysts in terms of their structure and composition. XPS results indicate that the pyrrolic-N groups are the most active sites, a finding that is supported by the correspondence between changes in pyridinic-N content and ORR activity that occur with changing temperature. Sulfur species are also structurally bound to carbon in the forms of C–Sn–C, an additional beneficial factor for the ORR.     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳（Co-PPy-C）载Pt 催化剂（Pt/Co-PPy-C）,其中Pt 的总质量占20%. 利用透射电镜（TEM）、光电子射线能谱分析（XPS）和X射线衍射（XRD）研究了催化剂的结构,用循环伏安（CV）、线性扫描伏安（LSV）等方法考察了其电化学活性及氧还原反应（ORR）动力学特性及耐久性. Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C（JM）颗粒尺寸（约2.5 nm）;催化剂在载体上分散均匀,粒径分布范围较窄. Pt/Co-PPy-C的电化学活性比表面积（ECSA）（75.1 m²·g^-1）高于商用催化剂的ECSA（51.3 m²·g^-1）. XPS测试表明,自制催化剂表面的Pt 主要以零价形式存在. 而XRD结果显示,自制催化剂中Pt（111）峰最强,Pt 主要为面心立方晶格. Pt/Co-PPy-C具有与Pt/C（JM）相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性（1.21 mA·cm^-2）高于商用催化剂的比活性（1.04 mA·cm^-2）,表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行. CV测试1000 圈后,Pt/Co-PPy-C和Pt/C（JM）的ECSA 分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C（JM）,在质子交换膜燃料电池（PEMFC）领域有一定的应用前景.     

Cu/Cu_2O nanoparticles co-regulated carbon catalyst for alkaline Al-air batteries

Developing high-efficiency,inexpensive,and steady non-precious metal oxygen reduction reaction(ORR) catalysts to displace Pt-based catalysts is significant for commercial applications of Al-air battery.Here,we have prepared the Cu/Cu_2 O-NC catalyst with excellent ORR performance and high stability,due to the synergistic effect of Cu and Cu_2 O nanoparticles.The half-wave potential(0.8 V) and the limiting-current density(5.20 mA/cm~2) of the Cu/Cu_2 O-NC are very close to those of the 20% Pt/C catalyst(0.82 V,5.10 mA/cm~2).Besides,it exhibits excellent performance with a maximal power density of 250 mW/cm~2 and a stable continuous discharge for more than 90 h in the Al-air battery test The promoting effects of Cu_2 O towards Cu-based ORR catalysts are illustrated as follows:(ⅰ) Cu_2 O is the major ORR active site by the redox of Cu(Ⅱ)/Cu(Ⅰ),which provides excellent ORR activities;(ⅱ) Cu can stabilize the location of Cu_2 O by assisting the electron transfer to Cu(Ⅱ)/Cu(Ⅰ) redox,which is conducive to the high stability of the catalyst.This work provides a useful strategy for enhancing the ORR performance of Cu-based catalysts.     

碳载钴酞菁催化剂的制备及其氧还原催化性能研究

研究了一种通过固相加热一步合成碳载钴酞菁复合催化剂(CoPc/C)的制备方法.通过XRD,IR对制备的催化剂进行了表征.结果显示,得到的产物为CoPc/C,平均粒径30nm.利用极化曲线和交流阻抗等电化学方法测试了其在碱性介质中对氧还原的催化性能.该催化剂在碱性介质中(6mol·L-1KOH)空气气氛下,氧还原的初始电位达到0V,电极电位为-0.10V vs·Hg/HgO时电流密度达到100mA·cm-2,有显著的氧还原电催化效果.对实验得到的极化曲线及交流阻抗数据进行拟合处理及计算,获得相关动力学参数.     

热处理碳载Fe-三聚氰胺及Fe-g-C3N4催化剂的氧还原催化性能

分别以三聚氰胺和三聚氰胺的聚合物为配体, 采用浸渍法合成了两种氧还原反应(ORR)催化剂Fe-N/C(1)和Fe-N/C(2). 通过X射线衍射光谱(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)和电化学测试对催化剂的成分、形貌和电催化性能进行了表征. 结果表明, 以三聚氰胺聚合物为配体制备的Fe-N/C具有更高的ORR催化活性. 在高温热处理过程中, 催化剂表面能形成更多的石墨N活性点, 是其ORR性能提高的重要原因.     

High performance Fe and N-codoped graphene quantum dot supported Pd3Co catalyst with synergistically improved oxygen reduction activity and great methanol tolerance

Designing high-performance and durable non-platinum catalysts as oxygen reduction reaction (ORR) catalysts is still a major barrier of fuel cell commercialization. In this work, simple hydrothermal and impregnation routes were applied to prepare non-platinum Pd-Co bimetallic nano-catalysts such as Fe-N doped graphene quantum dot (Fe-N-GQD) supported Pd₃Co (Pd₃Co/Fe-N-GQD 10 wt%), carbon supported Pd₃Co/C (10 wt%), graphene quantum dot supported Pd₃Co/C (10 wt%). The synthesized catalysts were physico-chemically characterized by X-ray diffraction (XRD), Raman spectroscopy, transmission electronmicroscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The electrochemical investigation was carried out in three electrode half-cell system to evaluate the catalyst activity for oxygen reduction reaction (ORR), the tolerance to methanol crossover and durability. In comparison to commercial Pt/C (ETEK, 20 wt%), the Pd₃Co/Fe-N-GQD with lower weight percentage catalyst (∼10 wt%) displayed comparable electrocatalytic activity toward ORR with even higher methanol-tolerance capability and durability. The fabricated Pd₃Co/Fe-N-GQD with (10 wt %) metal loading exhibited only 20% lower activity than Pt/C (ETEK, 20 wt%) toward ORR. Nevertheless the durability study of the catalyst in acidic media showed that the Pd₃Co/Fe-N-GQD preserve 40% of its activity while Pt/C (ETEK, 20 wt%) exhibited only 20% of its initial catalytic activity for ORR. Moreover the activity loss in the presence of methanol (0.1 M) was obtained for Pt/C (ETEK, 20 wt%) and Pd₃Co/Fe-N-GQD 35% and 14%, respectively. To investigate the role of catalyst support, catalytic activities of Pd₃Co/Fe-N-GQD, Pd₃Co/C, Pd₃Co/GQD and Pd/Fe-N-GQD were compared. The results demonstrated superior catalytic activity of Pd₃Co/Fe-N-GQD which could be related to the cocatalytic role of Fe-N-GQD due to the presence numerous of active sites exposed to the reactants.     

Highly efficient iron–nitrogen electrocatalyst derived from covalent organic polymer for oxygen reduction

Developing non-precious metal catalyst with high activity, good stability and low cost for electrocatalytic oxygen reduction reaction(ORR) is critical for the wide application of energy conversion system. Here, we developed a cost–effective synthetic strategy via silica assistance to obtain a novel Fe_3C/Fe–N_x–C(named as COPBP-PB-Fe-900-SiO_2) catalyst with effective active sites of Fe–N_xand Fe_3C from the rational design two-dimensional covalent organic polymer(COPBP-PB). The nitrogen-rich COP effectively promotes the formation of active Fe–N_x sites. Additionally, the silica not only can effectively suppress the formation of large Fe-based particles in the catalysts, but also increases the degree of carbonization of the catalyst.The as-prepared COPBP-PB-Fe-900-SiO_2 catalyst exhibits high electrocatalytic activity for ORR with a halfwave potential of 0.85 V vs. reversible hydrogen electrode(RHE), showing comparable activity as compared with the commercial Pt/C catalysts in alkaline media. Moreover, this catalyst also shows a high stability with a nearly constant onset potential and half-wave potential after 10,000 cycles. The present work is highly meaningful for developing ORR electrocatalysts toward wide applications.     

新型钴-聚吡咯-碳载Pt燃料电池催化剂的制备与表征

采用脉冲微波辅助化学还原法制备了钴-聚吡咯-碳(Co-PPy-C)载Pt催化剂(Pt/Co-PPy-C),其中Pt的总质量占20%.利用透射电镜(TEM)、光电子射线能谱分析(XPS)和X射线衍射(XRD)研究了催化剂的结构,用循环伏安(CV)、线性扫描伏安(LSV)等方法考察了其电化学活性及氧还原反应(ORR)动力学特性及耐久性.Pt/Co-PPy-C电催化剂的金属颗粒直径约1.8 nm,略小于商用催化剂Pt/C(JM)颗粒尺寸(约2.5 nm);催化剂在载体上分散均匀,粒径分布范围较窄.Pt/Co-PPy-C的电化学活性比表面积(ECSA)(75.1 m2·g-1)高于商用催化剂的ECSA(51.3 m2·g-1).XPS测试表明,自制催化剂表面的Pt主要以零价形式存在.而XRD结果显示,自制催化剂中Pt(111)峰最强,Pt主要为面心立方晶格.Pt/Co-PPy-C具有与Pt/C(JM)相同的半波电位;在0.9 V下,Pt/Co-PPy-C的比活性(1.21 mA·cm-2)高于商用催化剂的比活性(1.04 mA·cm-2),表现出更好的ORR催化活性.动力学性能测试表明催化剂的ORR反应以四电子路线进行.CV测试1000圈后,Pt/Co-PPy-C和Pt/C(JM)的ECSA分别衰减了13.0%和24.0%,可见自制催化剂的耐久性高于商用Pt/C(JM),在质子交换膜燃料电池(PEMFC)领域有一定的应用前景.