气相色谱-质谱法测定聚氯乙烯包装材料和食品模拟物中的46种增塑剂

建立了46种增塑剂在聚氯乙烯(PVC)食品包装材料中的含量及其在水、3%乙酸、10%乙醇和橄榄油4种食品模拟物中迁移量的气相色谱-质谱(GC-MS)测定方法。食品包装材料、水质模拟物和橄榄油中增塑剂分别采用溶解-沉淀法、正己烷液-液萃取和凝胶渗透色谱(GPC)法提取。采用GC-MS法,在选择离子监测模式(SIM)下对46种增塑剂进行定性,采用外标法进行定量测定。各种增塑剂在0.1～2.0 mg/L质量浓度范围内呈线性,相关系数为0.9910～0.9999,各组分检出限均在0.005～0.05 mg/kg之间。在2种食品模拟物中,3个浓度添加水平下46种增塑剂的加标回收率在69.51%～107.21%之间,精密度(RSD, n=6)为3.53%～18.95%。该方法可满足PVC食品接触制品及4种不同性质的食品模拟物中多种类增塑剂的快速筛查和准确定性、定量测定要求。     

Effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 films into food simulants: development and validation of a gas chromatographic method

A GC method to determine caprolactam in water, 15% ethanol, and olive oil food simulants was developed and validated. Linear ranges varied from 0.96 to 642.82 microg/mL for water, 0.64 to 800.32 microg/mL for 15% ethanol, and 1.06 to 1062.34 microg/g for olive oil, with correlation coefficients higher than 0.999. Method precision studies showed RSD values lower than 5.45%, while method accuracy studies showed recovery from 72 to 111% for all simulants. The effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 (PA-6) films intended for cheese into water, 15% ethanol, olive oil, and 3% acetic acid simulants was also studied. For migration assay, non-irradiated and irradiated (12 kGy) films were placed in contact with the simulant and exposed at 40 degrees C for 10 days. The validated method was used to quantify caprolactam migration from multilayer PA-6 films into the simulants, which ranged from 1.03 to 7.59 mg/kg for non-irradiated films, and from 4.82 to 11.32 mg/kg for irradiated films. Irradiation caused almost no changes in caprolactam levels, with the exception of olive oil, which showed an increase in the caprolactam level. All multilayer PA-6 films were in accordance with the requirements of the legislation for caprolactam migration.     

超高效液相色谱/静电场轨道阱高分辨质谱法同时测定塑料食品接触材料中光稳定剂和抗氧化剂的特定迁移量

建立了超高效液相色谱/静电场轨道阱高分辨质谱同时测定塑料食品接触材料中多种光稳定剂和抗氧化剂特定迁移量的方法。采用30 g/L乙酸、体积分数分别为10%、20%、50%的乙醇和油类模拟物(异辛烷)这5种食品模拟物对塑料食品接触材料进行处理,对处理液进行超高效液相色谱/静电场轨道阱高分辨质谱分析,外标法定量。该方法测定的40种目标化合物在相应的范围内均具有良好的线性关系,相关系数均大于0.998,定量限为0.01~1.00μg/L。考察了上述5种食品模拟物中光稳定剂和抗氧化剂的特定迁移量,平均加标回收率为81.46%~94.53%,相对标准偏差为3.25%~9.99%。应用该方法对市售塑料食品接触材料进行了测定,结果在部分样品中检出了不同含量的光稳定剂和抗氧化剂。该方法灵敏度高,定量限低,满足塑料食品接触材料中光稳定剂和抗氧化剂特定迁移量的检测要求。     

高效液相色谱法同时测定食品接触材料中抗氧化剂和紫外吸收剂的迁移量

采用高效液相色谱技术,建立了食品接触材料中多种抗氧化剂和紫外吸收剂迁移水平的检测方法。该方法测定的23种目标化合物具有较好的线性关系,相关系数（r²）≥ 0.9998,检出限和定量限分别在0.01到0.22 mg/L之间和0.03到0.85 mg/L之间。依据欧盟指令（EU）No. 10/2011,考察了5种食品模拟物30 g/L乙酸、10%（v/v）乙醇、20%（v/v）乙醇、50%（v/v）乙醇和油类模拟物（异辛烷）中抗氧化剂和紫外吸收剂的迁移量。该方法回收率在92.8%~117.7%之间,相对标准偏差在0.95%~9.72%之间。探讨了不同实验条件对抗氧化剂和紫外吸收剂回收率的影响。结果表明,该方法准确、稳定,完全满足欧盟指令（EU）No 10/2011和GB 9685-2008对食品接触材料及制品中抗氧化剂和紫外吸收剂特定迁移量（SML）的限量要求,并利用该方法测定了30批次食品接触材料中抗氧化剂和紫外吸收剂的迁移水平。     

高效液相色谱-串联质谱法快速测定水基食品模拟物中28种受限芳香族伯胺的迁移量

建立了高效液相色谱-串联质谱(HPLC-MS/MS)联用方法用于快速测定水基食品模拟物(10%乙醇、30 g/L乙酸和20%乙醇)中28种芳香族伯胺的迁移量。用水基食品模拟物浸泡待测样品中一定时间(在100 ℃条件下)后,冷却至室温并混匀,所得浸泡液经亲水性聚四氟乙烯针头式过滤器过滤后,直接进行HPLC-MS/MS测定。采用Agilent Zorbax SB-Phenyl柱,以水和0.1%甲酸-25%乙腈-甲醇溶液为流动相进行梯度洗脱分离;质谱具电喷雾离子源,在正离子和分段式多反应监测(MRM)模式下检测。结果表明,方法定量限为0.002～10 μg/L,在5～100 μg/L或10～100 μg/L范围内线性关系良好(r2＞0.995);在10、20、40 μg/L水平的加标回收率为76.6%～114%,相对标准偏差为1.53%～8.97%。该方法样品前处理简单快速,色谱分离效果和线性关系好,检出限较低、回收率和准确度高,且完全满足欧盟(EU)No 10/2011法规中对芳香族伯胺特定迁移量的限量要求。该方法已成功应用于30批次出口欧盟的食品接触材料相关制品中芳香族伯胺特定迁移量的检测。     

Application of capillary electrophoresis in migration studies of food contact materials – part 1: Substituted phenolic additives

A method has been developed to determine 11 phenolic antioxidants in the food simulants distilled water, 3% acetie acid, and 15% ethanol, using; micellar capillary electrophoresis (MCE). All the phenols could he analyzed within 35 min. The analytical recovery from spiked simulants was 80 to 119% except for 2,6-di-tert-butyl-4hydroxytoluenc (BHT) and octyl gallate, which could not be recovered from 3% acetic acid simulant. Calibration graph correlation coefficients for the 11 phenols were 0.982 to 0.999. Limits of detection (LoDs) were from 2.8 to 8.6 mg/L. These LoDs are well below European Union migration limits for these substances. It is concluded therefore that MCE offers a rapid and reliable analysis for the control of migration from plastics intended for food contact which employ these phenols as antioxidants.     

高效液相色谱-紫外检测法同时测定食品接触材料中7种苯多酸及其衍生物的特定总迁移量

建立了高效液相色谱-紫外检测(HPLC-UV)同时测定5种食品模拟物(10%(v/v)乙醇、20%(v/v)乙醇、50%(v/v)乙醇、3%(w/v)乙酸和橄榄油)中偏苯三甲酸、偏苯三甲酸酐、间苯二甲酰氯、间苯二甲酸、对苯二甲酰氯、邻苯二甲酸、对苯二甲酸的特定总迁移量(SML(T))的方法。用食品模拟物浸泡待测样品,冷却至室温并混匀,水基食品模拟物经亲水性聚四氟乙酸针头过滤器过滤后进样;橄榄油用0.1%(w/v)乙酸铵水溶液提取后,下层清液用亲水性聚四氟乙烯针头过滤器过滤后进样。用Synergi Polar-RP色谱柱(250 mm×4.6 mm, 4 μm)分离,梯度洗脱,检测波长为232 nm。5种食品模拟物中的定量限为0.1~0.2 mg/kg;水基食品模拟物在0.5~12 mg/L、橄榄油食品模拟物在0.5~12 mg/kg范围内线性关系良好(r² > 0.99991); 1.25、2.5、6.25 mg/kg水平的加标回收率为94.3%~105%,相对标准偏差为0.1%~2.3%。结果表明,该方法的色谱分离和线性关系较好,回收率和准确度高,完全满足欧盟(EU)No 10/2011法规附表2中7种苯多酸及其衍生物的SML(T)的限量要求,并已应用于实际样品的检测。     

塑料食品包装中对苯二酸向食品模拟物迁移的高效液相色谱测定方法

建立了高效液相色谱(HPLC)法测定塑料食品包装中对苯二酸(TA)向食品模拟物的迁移量.对前处理净化技术及色谱条件进行了优化,并利用超高效液相色谱-串联质联(UPLC-MS/MS)进行确证.该方法在0.3～30 mg/L范围内线性关系良好,检出限为0.3 mg/L.食品模拟物中对苯二酸的加标回收率在89.0%～110.0%之间,其相对标准偏差为0.45%～9.24%,重复性和再现性良好.利用该方法对实际塑料包装制品中对苯二酸进行了迁移测定.     

高效液相色谱-紫外法快速测定塑料类食品接触材料及制品中7种对苯二甲酸酯或苯甲酸酯的特定迁移量

建立了高效液相色谱-紫外检测（HPLC-UV）法快速测定从塑料类食品接触材料及制品迁移至10%（v/v）乙醇、3%（m/v,即3 g/100 mL）乙酸、4%（v/v）乙酸、20%（v/v）乙醇、50%（v/v）乙醇、95%（v/v）乙醇和橄榄油7种食品模拟物中对苯二甲酸二甲酯、对苯二甲酸二辛酯、苯甲酸甲酯、苯甲酸乙酯、苯甲酸丙酯、苯甲酸丁酯和新戊二醇二苯甲酸酯的特定迁移量。考察了多种提取溶剂、QuEChERS dSPE EMR-Lipid试剂盒和Captiva EMR-Lipid试剂盒对橄榄油食品模拟物中7种对苯二甲酸酯或苯甲酸酯的提取或净化效果。以甲醇和水为流动相进行梯度洗脱,7种对苯二甲酸酯或苯甲酸酯在苯基柱上于17 min内达到基线分离。检测波长为237 nm,进样量为10 μL。7种对苯二甲酸酯或苯甲酸酯在7种食品模拟物中的定量限为0.2~8.1 mg/kg、1~80 mg/L或8~160 mg/kg,相关系数r≥0.9998。在2或8、60、80或160 mg/kg 3个加标水平的回收率为91.7%~106%,相对标准偏差为0.1%~3.1%。该方法样品前处理简便,色谱分离和线性关系好,回收率和重复性较好,已应用于实际样品的检测。     

Quantitative determination of 22 primary aromatic amines by cation-exchange solid-phase extraction and liquid chromatography–mass spectrometry

Primary aromatic amines (PAAs) have been broadly studied due to their high toxicity. In this work a method for the analysis of 22 PAAs in aqueous simulants has been developed. The method is based on a solid-phase extraction step using cation-exchange cartridges and the subsequent analysis of the extracts by ultra-high-performance liquid chromatography with mass spectrometric detection. The recoveries obtained for all the amines analyzed ranged between 81 and 109%, linear range was between 0.03 and 75 μg L⁻¹, with the RSD values between 4.5 and 13.4% and an average value of 7.5% and limits of detection at μg L⁻¹ level. The method has been applied to two real samples obtained from migration experiments of polyurethane based laminates to simulant B (water with 3% (w/v) acetic acid) which represents the worst case for the migration of aromatic amines. The main amines found in both samples were methylenedianiline isomers, obtained from the corresponding residual diisocyanates used during polyurethane adhesive polymerization. The total amine concentration found was 26 and 6.3 μg of aniline equivalents per kg of food simulant.     

Analytical tools for identification of non-intentionally added substances (NIAS) coming from polyurethane adhesives in multilayer packaging materials and their migration into food simulants

Adhesives used in food packaging to glue different materials can provide several substances as potential migrants, and the identification of potential migrants and migration tests are required to assess safety in the use of adhesives. Solid-phase microextraction in headspace mode and gas chromatography coupled to mass spectrometry (HS-SPME-GC-MS) and ChemSpider and SciFinder databases were used as powerful tools to identify the potential migrants in the polyurethane (PU) adhesives and also in the individual plastic films (polyethylene terephthalate, polyamide, polypropylene, polyethylene, and polyethylene/ethyl vinyl alcohol). Migration tests were carried out by using Tenax(?) and isooctane as food simulants, and the migrants were analyzed by gas chromatography coupled to mass spectrometry. More than 63 volatile and semivolatile compounds considered as potential migrants were detected either in the adhesives or in the films. Migration tests showed two non-intentionally added substances (NIAS) coming from PU adhesives that migrated through the laminates into Tenax(?) and into isooctane. Identification of these NIAS was achieved through their mass spectra, and 1,6-dioxacyclododecane-7,12-dione and 1,4,7-trioxacyclotridecane-8,13-dione were confirmed. Caprolactam migrated into isooctane, and its origin was the external plastic film in the multilayer, demonstrating real diffusion through the multilayer structure. Comparison of the migration values between the simulants and conditions will be shown and discussed.     

A novel method for the determination of migration of contaminants from food contact materials

A neutron activation method has been developed for the analysis of high density polyethylene, low density polyethylene, polypropylene, polyethylene terephthalate and polystyrene food contact plastics. The method provides determination of over 50 elements at concentrations below 1 mg kg^–1. This technique has now been extended to study migration from food contact materials into standard food simulants (olive oil, acetic acid, ethanol and water). Samples of plastic are irradiated in a thermal neutron flux to produce radionuclides of the elements present in the plastic. Over a period of time the radionuclides of these elements may travel from the plastic into the food simulants, and hence the migration can be determined. Gamma ray spectrometry is performed on the simulants at the end of the test to quantify the migration. Any activity present must be due only to the migration of radionuclides of elements in the plastic and nothing else. This eliminates the need for a blank determination, which is required with existing migration methods. Preliminary studies have shown that detection limits of around 0.002 mg kg^–1 can be achieved for Sb in a retail polyethylene terephthalate (PET) bottle. This can be compared to levels of 0.005     

Evaluation of the migration of UV-ink photoinitiators from polyethylene food packaging by supercritical fluid chromatography combined with photodiode array detector and tandem mass spectrometry

UV-ink photoinitiators (PIs), which are used to initiate polymerization reaction for the curing of inks and lacquers, have become a kind of contaminant residues in printing plastic food packaging. The residual PIs in packaging may pose a potential threat to customers. In this work, migration behaviors of 13 PIs from a polyethylene (PE) packaging to food simulants according to regulation EU No 10/2011 were studied by supercritical fluid chromatography combined with photodiode array detector and tandem mass spectrometry (SFC-PDA-MS/MS). The method simultaneously analyzed 13 PIs within 4.5 min and was sensitively with low limits of detection of 0.02–2.16 μg/L, which could meet high throughput analysis for control the quality of food packaging. The migration results revealed that Irgacure 819, Darocure 1173 and TPO, which had low migration rates, should be preferably selected by plastic food packaging manufacture for food safety.     

MALDI-MS and colorimetric analysis of diisocyanate and polyol migrants from model polyurethane adhesives used in food packaging

The identification of the migrants, into food simulants, from a series of polyurethane adhesives used in the manufacture of plastic film laminates for use in common food packaging is described. Commercial materials, based on four different model adhesive systems, were prepared by an industrial collaborator. The MALDI-MS fingerprint patterns of the three polyether and one polyester polyol components of these adhesives were obtained for reference purposes. The decrease in the level of diisocyanate as a migrant versus time after lamination was confirmed by colorimetric measurements. The migration of the standard polyol samples through polyethylene pouches into water at 70 degrees C has been demonstrated and also the attenuation effect for different polyols. Cured laminates in the form of pouches were used to carry out the migration experiments into distilled water, inside the pouch, at 70 degrees C over a period of 2 h. Comparison of the migration results from the food packaging laminates with those from the polyethylene film confirmed the migration of unreacted polyol components for the polyether-based systems. Cyclic oligomers from the polyol starting materials were identified as the migrants from the polyester-based adhesive.     

Analysis of 16 phthalic acid esters in food simulants from plastic food contact materials by LC‐ESI‐MS/MS

An RP LC‐ESI‐MS/MS method for the determination of the migration of 16 primary phthalic acid esters from plastic samples has been developed using distilled water, 3% acetic acid, 10% alcohol, and olive oil as food simulants. Detection limits were 1.6–18.5 μg/kg in distilled water, 1.4–17.3 μg/kg in 3% acetic acid, 1.4–19.2 μg/kg in 10% alcohol, and 31.9–390.8 μg/kg in olive oil. The RSDs were in the range of 0.07–11.28%. The real plastic products inspection showed that only few analyzed samples were phthalates contaminated. Bis‐2‐ethylhexyl ester and dibutyl phthalate were the common items migrated from the plastic products into food and feeds, but the migration concentrations were far below the limits set by European Union (1.5 mg/kg for bis‐2‐ethylhexyl ester and 0.3 mg/kg for dibutyl phthalate).     

Determination of diethylhexyladipate and acetyltributylcitrate in aqueous extracts after cloud point extraction coupled with microwave assisted back extraction and gas chromatographic separation

The determination of commercial plasticizers (di-(2-ethylhexyl)adipate (DEHA) and acetyl tributyl citrate (ATBC)) in aqueous solutions is described. The newly proposed technique of applying microwaves to cloud point extracts in order to enable combination with gas chromatographic analysis has been used for this purpose. Both plasticizers were entrapped in the micelles of the non-ionic surfactant Triton X-114 and removed from the bulk phase by centrifugation. Micellization was enhanced by increasing the ionic strength of the solution with concentrated NaCl. Extraction recoveries of the proposed method were over 95% for water and 3% (w/v) aqueous acetic acid and over 85% for 10% (v/v) aqueous ethanol, respectively. The calibration curves obtained, following the proposed methodology have a linear range between 50 and 2000 microg/L for each analyte while the detection limits were as low as 15 and 19 microg/L for DEHA and ATBC, respectively, with an RSD below 5% even for low concentrations. As an analytical demonstration the proposed methodology was applied for the determination of the migration levels of the selected plasticizers from a PVC food packaging film into aqueous simulants.     

Effects Of Compression, Stacking, Vacuum Packing and Temperature on the Migration of Bisphenol A from Polyvinyl Chloride Packaging Sheeting into Food Simulants

Summary The effects of compression, stacking, vacuum packing and temperature on the migration of bisphenol A from polyvinyl chloride plastic sheeting into European Union food simulants (water, 3% acetic acid and olive oil), 1.5% agar, and mixtures of olive oil with various proportions of inert material (fine washed sea sand) were evaluated using previously developed methods for identification and quantitation of migrants. Compression, stacking and increasing temperature all increased migration.Presented at the International Symposium on Separation and Characteristics of Natural and Synthetic Macromolecules, Amsterdam, The Netherlands, February 5–7, 2003     

PVC塑料包装中化学物总迁移的研究

食品包装安全是食品安全的一个重要环节.食品容器、包装等接触材料与食品长期接触会发生"迁移",分为总迁移(overall migration)和特定迁移(specific migration)[1].其中,特定迁移是指某一特定物质在食品包装或容器与食品接触过程中发生的迁移;总迁移是从塑料材料或制品样品到试验媒介的组分总体迁移量.就物质而言,有可知物与未知物,就过程而言,有包装向食品的迁移,也有食品向包装的渗透、吸收等.进行总迁移实验有助于更全面了解一种材料与食品接触会发生的总体变化,对特定迁移的研究起有辅助与补充作用.欧盟对于食品模拟物、样品及前处理[2]、迁移测试方法[3]都有相应规定[4],本实验采用整体浸泡法,研究了PVC材料中化学物在不同食品模拟物中的总迁移.1 实验部分1.1 实验试剂和器材     

Application of single-drop microextraction to the determination of dialkyl phthalate esters in food simulants

A fast and simple method, using static single-drop microextraction (SDME), has been developed to facilitate the identification and quantification of seven dialkyl phthalate esters in the three aqueous food simulants. The simulants were: A, distilled water; B, 3% (w/v) acetic acid/water; and C, 15% (v/v) ethanol/water. The extraction is performed by simply suspending a drop of organic solvent in the aqueous sample using a conventional gas chromatography (GC) microsyringe. Following extraction, the organic phase is withdrawn into the syringe and analyzed by gas chromatography and flame ionization detection (FID). The optimized method yields a linear calibration curve over three orders of magnitude for all the simulants, and method detection limits (MDLs) allowing detection of all the studied compounds at concentrations below migration limits established by the European Union. The accuracy of the SDME method was tested and compared to that of solid-phase microextraction (SPME) by recovery experiments using spiked samples, with results ranging from 85 to 115% in most cases.     

超高效液相色谱-串联质谱法同时测定食品接触材料及制品中9种抗氧化剂迁移量

为了评估食品接触材料及制品中抗氧化剂的迁移风险,采用超高效液相色谱-串联质谱法(UPLC-MS/MS)建立了同时测定食品接触材料及制品中9种抗氧化剂迁移量的方法。采用C18色谱柱对迁移实验后的食品模拟物中9种抗氧化剂进行分离,1 mmol/L氟化铵和甲醇为流动相洗脱,采用电喷雾离子源(ESI),多反应监测(MRM)正负离子模式进行扫描。结果表明,9种抗氧化剂的色谱分离效果良好,并在0.3~6 mg/L质量浓度范围内与其峰面积均呈良好的线性关系,检出限为0.1 mg/L。加标回收率为93.9%~106%,相对标准偏差(RSD)为0.80%~9.3%。该方法快速高效、线性范围好,适用于塑料食品接触材料及制品中9种抗氧化剂迁移量的检测。