Temperature-independent bending sensor with tilted fiber Bragg grating interacting with multimode fiber

A new type fiber bending sensor based on a tilted fiber Bragg grating (TFBG) interacting with a multimode fiber (MMF) is presented. The sensing head is formed by insertion of a small section of MMF between a single-mode fiber (SMF) and the TFBG. The average reflective power in the cladding modes decreases with the increase of curvature. The measurement range of the curvature from 0 to 2.5 m⁻¹ with a measurement sensitivity of −802.4 nW/m⁻¹ is achieved. The proposed sensor is also proved as temperature-independent from the experimental investigation.     

Highly sensitive bend sensor with hybrid long-period and tilted fiber Bragg grating

We demonstrate a new type of fiber optic bend sensor with a hybrid structure made up of a long period grating (LPG) and a tilted fiber Bragg grating (TFBG). The sensing mechanism is based on the spectrum of power transfers between the core and cladding modes from a TFBG located downstream from a LPG. We show that the curvature of a beam can be determined by the reflected power difference between the core mode and the recoupled cladding modes. We further provide design rules for the LPG and TFBG to optimize and linearize the sensor response. In addition, the temperature cross-sensitivities of this configuration are also investigated for two different types of fiber.     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

A compact graphene Q-switched erbium-doped fiber laser using optical circulator and tunable fiber Bragg grating

We demonstrate a passively Q-switched tunable erbium-doped fiber laser(EDFL)based on graphene as a saturable absorber(SA).A three-port optical circulator(OC)and a strain-induced tunable fiber Bragg grating(TFBG)are used as the two end mirrors in an all-fiber linear cavity.The Q-switched EDFL has a low pump threshold of 23.8 mW.The pulse repetition rate of the fiber laser can be widely changed from 9.3 kHz to 69.7 kHz by increasing the pump power from23.8 mW to 219.9 mW.The minimum pulse duration is 1.7μs and the highest pulse energy is 25.4 nJ.The emission wavelength of the laser can be tuned from 1560.43 nm to 1566.27 nm by changing the central wavelength of the straininduced TFBG.     

Lateral force sensor based on a core-offset tilted fiber Bragg grating

A novel lateral force sensor based on a core-offset tilted fiber Bragg grating (TFBG) is proposed and experimentally demonstrated. The lateral force is determined by the differential reflected powers between the cladding mode and Bragg mode in the TFBG. The sensors respond monotonically with the lateral force increasing from 0 to 1.75 N. The sensitivity of such a core-offset TFBG sensor can be tailored by choosing different core-offset values. The simple differential power detection method makes the implementation of the sensor system cost-effective and free of the influence of environmental and system fluctuations.     

Cascaded tilted fiber Bragg grating for enhanced refractive index sensing

We proposed and experimentally demonstrated a cascaded tilted fiber Bragg grating(TFBG) for enhanced refractive index sensing. The TFBG is UV-inscribed in series in ordinary single-mode fiber(SMF) and reduced-diameter SMF with the same tilt angle, and then excites two sets of superposed spectral combs of cladding modes. The cascaded TFBG with total length of 18 mm has a much wider wavelength range over 100 nm and narrower wavelength separation than that of a TFBG only in the SMF, enabling an enlarged range and a higher accuracy of refractive index measurement. The fabricated TFBG with the merits of enhanced sensing capability and temperature self-calibration presents great potentials in the biochemical sensing applications.     

Widely tunable mode-locked all-fiberized Yb-doped fiber laser with near-transform-limited spectrum linewidth

A widely tunable mode-locked all-fiberized Yb-doped fiber laser with near-transform-limited spectrum linewidth is used. It consists of a tunable fiber Bragg grating (TFBG) and a fiber-coupled LiNbO₃ phase modulator (PM) in a linear cavity. The TFBG is used to achieve tunable emission wavelength, and the intracavity PM is used to achieve actively mode-locking operation. We have experimentally demonstrated that the laser-emitting wavelength can be tuned between 1,041 and 1,091 nm with power fluctuation less than 3 dB. The temporal width of the laser pulse is about 1 ns, and the pulses are near transform-limited with a spectral linewidth of 1.3 GHz. The results may find useful application in optical communication and optical measurement system.     

Compact in-fiber mode adapter based on double-cladding fiber for multimode fiber access networks

A simple method for coupling light from a laser diode (LD) to multimode fiber (MMF) by using a compact in-fiber mode adapter, which is constructed with double-cladding fiber is presented, for the first time. Strong cladding-mode resonance across the thin-thickness inner cladding is used to excite the cladding modes. Principle of proposed mode adapter is theoretically investigated and its performances are experimentally verified by measurement results. By comparing the direct connection between LD and MMF, the coupling efficient of transmission power is improved by using our proposed adapter.     

Simulation and experimental research on polymer fiber mode selection polished coupler

Multimode dispersion is the main obstacle for high bandwidth in multimode optical fiber （MMF） communication system. Mode selection is an effective method to oppress multimode dispersion. We propose and investigate a kind of polymer optical fiber polished coupler. Beam propagation method （BPM） is employed to calculate the coupling coefficient of transmission modes in MMF coupler, and an output pattern from coupling branch is obtained. Analysis and experiment show that this coupler can select certain modes by changing polished depth, contact area, and intersection angle of two branches, which means that the device can be employed both as a mode selector and a sensor. In addition, simulation shows that five times bandwidth enhancement may be realized by selecting modes with the polymer fiber polished coupler.     

多模光纤中简并模式群的分别探测

用多模倾斜光纤光栅(Tilted fiber Bragg grating,TFBG)实现多模光纤中简并模式群(Degenerated modegroup,DMG)的分别探测。多模倾斜光纤光栅将光纤中的导模耦合到辐射光线,用透镜将辐射光线聚焦在焦平面上,使非简并模式群对应的辐射光线的像在焦平面上分离。在焦平面上用空间滤波器使简并模式群选择透过并进行分别探测。用芯径为62.5μm的标准通信多模光纤进行了简并模式群分别探测实验,用单模光纤激励多模光纤,测量简并模式群功率随激励光纤的横向对准偏差的变化关系。低阶简并模式群的测量结果与仿真计算结果基本一致,高阶简并模式群的测量结果与仿真结果有一些不同。用倾斜光纤光栅进行单简并模式群激励,在单简并模式群条件下测量简并模式群耦合效率的想法还需进一步实验验证。     

倾斜光纤光栅溶液折射率传感器的实验研究

根据倾斜光纤光栅(TFBG)和表面镀金的TFBG传感器测量折射率的基本原理,通过OptiGrating软件模拟了不同浓度溶液下TFBG的透射谱和芯层模与某阶包层模耦合引起的谐振峰,初步得出了TFBG各阶包层模随着外界折射率的增大而向右偏移、在一定的传感范围内中心波长与外界折射率呈线性关系的结论。用小型离子溅射仪对TFBG镀45 nm厚度左右的金膜,并用扫描电镜在微观上观察镀膜效果。通过不同浓度下的NaCl溶液、MgCl₂溶液、CaCl₂溶液实验,对比研究了裸TFBG和镀金TFBG传感器对溶液折射率的传感特性。从而验证了模拟仿真得出的结论并定量分析得知：镀金后具有表面等离子体共振的TFBG溶液折射率灵敏度大于500 nm·RIU-1,而裸TFBG为2 nm·RIU-1左右,大约提高了200～300倍,且在一定范围内中心波长与溶液折射率的线性拟合度都在0.99以上。     

应用耦合模理论研究光在圆对称双包层光纤中的传输

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

High-speed data transmission over a 1 km broad wavelength window multimode fiber

For cost and design simplicity, various optical network architectures have been proposed in which downstream traffic from the optical line terminal to the optical networking unit is transmitted by carriers in the 1550 nm window, and upstream traffic by those in the 1300 nm window. A new generation of multimode fiber (MMF) has been designed to accommodate this requirement and to address technical challenges associated with fiber coupling. By restricting the number of modes at both fiber input and output, using off-the-shelf single-mode transceivers, single-wavelength 40 Gbit/s data transmission over a 1 km broad wavelength window multimode fiber has been demonstrated with only a 1.5 dB power penalty. The capacity in this new class of MMF is expected to increase with conventional technologies in single-mode fiber such as wavelength-division multiplexing and polarization multiplexing.     

应用耦合模理论研究光在圆对称双包层光纤中的传输(英文)

为了深入理解双包层光纤的光场传输特性,应用耦合模理论将双包层光纤等效为相互耦合的单模光纤和环形芯光纤,研究了圆对称的双包层光纤的光场传输.通过计算单模光纤LP01模和环形芯光纤导模的耦合系数发现了环形芯光纤LP0n模的耦合系数远大于其它导模的耦合系数,且LP0n模中的高阶模比低阶模的耦合系数大.据此,应用耦合模理论计算得到了该双包层光纤的光传输特性,计算结果发现光场沿光纤轴向呈近似周期分布,且纤芯中光功率变化的平均周期随波长递增,但平均归一化功率与光纤参数紧的选择有关.     

Design of triangular FBG filter for sensor applications using covariance matrix adapted evolution algorithm

The design of triangular fiber Bragg grating (TFBG) filters using covariance matrix adapted evolution strategy (CMAES) algorithm is presented. The TFBG filter can be used as a readout device in FBG-based sensor applications. Two different filter design problems are investigated. The first problem is the design of TFBG filter for a specified bandwidth. The other is maximizing the bandwidth of the TFBG filter for a given grating length and maximum index modulation of the FBG. A more practical asymmetrical triangular FBG filter design is also considered. The results show that for the same grating length and maximum index modulation, a larger bandwidth can be achieved with a chirped grating. The maximized bandwidth design can be used to achieve the maximum possible bandwidth for the specified grating length, maximum index modulation and chirp rate. The results obtained using CMAES algorithm (codes available at http://www.ntu.edu.sg/home/epnsugan) is compared with the results of PSO and other algorithms. Comparisons show that the CMAES algorithm is more consistent in obtaining the best solution with reduced computation time. Hence, the CMAES algorithm is effective for the design of TFBG filters for sensor applications.     

折射率不敏感的级联型单模-少模-单模光纤温度传感器

提出了一种折射率不敏感的级联型单模-少模-单模光纤温度传感器。在制作传感器的过程中,设置熔接电流为100 mA,通过将少模光纤与单模光纤进行无错位熔接,以激发稳定的传输模式,形成光纤马赫-曾德尔干涉仪。由于外界环境的改变会引起少模光纤中不同模式之间相位差的改变,从而导致干涉条纹的漂移,因此通过检测干涉条纹的漂移量就可以实现待测参数的检测。少模光纤可以传输LP₀₁,LP₁₁,LP₂₁,LP₀₂共四种模式的光。实验中对长度为81.5 mm的传感器光谱进行分析可知,发生干涉的两个模式主要是LP₀₁模和LP₁₁模。利用该长度的级联型单模-少模-单模光纤传感器进行折射率和温度传感实验,结果表明,随着传感器温度不断的增加,其传输光谱出现了明显的蓝移现象,在27.6~93.8 ℃的温度变化范围内,灵敏度高达-85.9 pm·℃-1,且具有较好的线性度;在甘油折射率为1.347 1~1.443 9变化范围内,其传输光谱没有出现明显的漂移现象,灵敏度仅为3.697 34 nm·RIU-1,具有折射率不敏感特性。因此,相对于传统的包层模干涉型与多模干涉型光纤传感器,所提出的基于FMF的传感器更易于实现对传输模式的控制与分析,且具有结构简单、易于制备、灵敏度高等优点,能够避免温度与折射率同测的交叉敏感问题,可用于电力系统、生物医学、航空航天等领域的温度检测。     

Fabrication of a tilted fiber Bragg grating with a designed reflection spectrum profile

A method of fabricating a tilted fiber Bragg grating (TFBG) with a designed reflection spectrum profile is proposed and demonstrated experimentally. In a reflective TFBG the central wavelength and the reflectivity are dependent on the tilt angles. Controlling the rate at which the tilt angle is continuously varied and the exposure dose in the UV-light writing process permits accurate control of the bandwidth and reflectivity of the grating. The experimental result agrees well with TFBG theory and calculation.     

Method for measuring liquid phase diffusion based on tilted fiber Bragg grating

We propose and experimentally demonstrate a method for measuring liquid phase diffusion based on tilted fiber Bragg grating (TFBG). By monitoring the transmission spectra of the TFBG placed at different positions of the diffusion zone and calculating the normalized area enclosed by the upper and lower envelope curves of the cladding modes, the distribution curves of the glycerol concentration are obtained, according to the experimental calibration formulas between the glycerol concentration and the normalized area. This method can conveniently achieve remote and distributed measurement of the liquid phase diffusion in hostile environment because of its all-fiber structure.     

Intermodal interference of LP01 and LP11 modes inpanda fibers

LP01 and LP11 mode interferences in high-birefringence （Hi-Bi） panda fibers are theoretically and experimentally presented. The propagation characteristics of both the fundamental and second-order modes in Hi-Bi panda fibers are investigated, and the interference output intensity distribution of the LP₀1 and LP₁1 modes in panda fibers are thoroughly examined. An experiment is conducted to verify the feasibility of modal interference sensors. The results show that the two-lobe interference pattern of panda fibers generates energy exchanges when external strain is applied on the fiber. Moreover, Hi-Bi panda fibers can be used to design voltage sensors.