Wavelength-selective coupling of dual-core photonic crystal fiber and its application

We investigate the coupling characteristics of photonic crystal fiber composed of two cores with different index profiles. The index curves of the fundamental modes of the two cores can cross at a desired wavelength by choosing appropriate index profiles of the cores. As a result, wavelength-selective coupling is achieved. The designed coupler can be applied as an oDtical fiber bandstop filter with 26-nm bandwidth.     

High-speed data transmission over a 1 km broad wavelength window multimode fiber

For cost and design simplicity, various optical network architectures have been proposed in which downstream traffic from the optical line terminal to the optical networking unit is transmitted by carriers in the 1550 nm window, and upstream traffic by those in the 1300 nm window. A new generation of multimode fiber (MMF) has been designed to accommodate this requirement and to address technical challenges associated with fiber coupling. By restricting the number of modes at both fiber input and output, using off-the-shelf single-mode transceivers, single-wavelength 40 Gbit/s data transmission over a 1 km broad wavelength window multimode fiber has been demonstrated with only a 1.5 dB power penalty. The capacity in this new class of MMF is expected to increase with conventional technologies in single-mode fiber such as wavelength-division multiplexing and polarization multiplexing.     

Fabrication of an optical fiber reflective notch coupler

A method of fabricating a reflective notch coupler in an optical fiber has been developed. The coupler consists of a 45° microprism that penetrates into the core of a multimode optical fiber. One face, at 90° to the fiber axis, is nonreflective, and one face, at 45° to the fiber axis, is reflective. Our method of fabricating a notch and selectively mirroring only the 45° face is low-cost, precise, and easily scalable. The coupler allows near-100% coupling of light into an optical fiber from the side, while allowing coupling of any desired fraction of light out from the core at a 90° angle on the opposite side of the fiber.     

Spatiotemporal and Thermal Analysis of VCSEL for Short-range Gigabit Optical Links

High-speed Optoelectronic Modules using Vertical Cavity Surface Emitting Lasers (VCSEL) coupled to Multi Mode Fibers (MMF) are a performing and low-cost solution for 10 Gigabit Ethernet (10 GbE) in short-distance optical links. A complete model of the spatiotemporal behavior of multimode VCSELs, through static and dynamic response, noise, thermal effects, and its coupling to MMF has been investigated. Relative Intensity Noise shows modal dependence and can be affected by spatial filtering due to coupling and fiber propagation. Simulations permit to evaluate critical parameters, such as modulation formats, launching conditions, and operating temperature for global bandwidth and eye diagram optimization up to 10 Gb/s. Simulation results are compared to measurements on prototype optoelectronic modules.     

Polymer optical waveguide based on integrated optics

The fabrication and characterization of refractive index profiles of multimode mode polymer optical waveguides is reported. Effect of annealing temperature on guided losses of polymer (polystyrene) thin film optical waveguide is also presented. Efficient coupling over a 110 nm spectral bandwidth was experimentally demonstrated with a prism-coupler designed to match the dispersion of a particular waveguide.     

Performance of directly modulated OFDM data over multimode fiber link

The performance of orthogonal-frequency-division-multiplexing (OFDM) technology in the multimode fiber (MMF) optical communication system is investigated numerically. The mode dispersion in MMF is analyzed by utilizing the optical angular spectrum analysis method. Simulation results in terms of bit-error-rate (BER) and signal-to-noise ratio (SNR) show that the transmission distance can reach up to 2.5-km at 10^− 3 BER for 40-Gb/s data. Results of different modulation formats further indicate that better performance can be achieved by adopting multi-level modulation format.     

Signal beating elimination using single-mode fiber to multimode fiber coupling

We experimentally demonstrate an all-passive fiber-based approach to prevent undesired beating during signal merging and detection. Beating occurs when optical signals of very close or the same wavelength are combined at a coupler and detected using a photodetector. Our approach is based on signal coupling from several single-mode fibers to a single piece of multimode fiber without interference, such that different signals propagate in different modes with different spatial positions inside the multimode fiber. We have investigated signal beating when the signals are coherent, partially coherent, or incoherent with each other. The measured results for single-mode to multimode coupling show signal beating is substantially reduced, resulting in widely opened eye diagrams and error-free bit error rate performance.     

单模与多模光纤耦合器的光束合波

现有的光纤耦合器在作为分波器使用时具有较低的插入损耗,在作为合波器时插入损耗较大,为实现低损耗合波目的,提出一种由单模与多模光纤共同构成的混合型光纤耦合器。利用耦合波方程理论分析其工作原理,计算机模拟其耦合过程。采用熔锥法制作工艺,完成单模与多模光纤耦合器的制作,实验结果与理论模拟相吻合;该器件单模到多模光纤的耦合效率、多模到多模光纤的耦合效率均在90％以上,实现了两路光束的功率合波。作为低插入损耗合波器件可广泛应用于光通信以及双包层光纤激光器抽运光的注入。     

Dynamics of an optical signal in a multimode waveguide structure

A mathematical model of linear dynamic distortions of average signal power in a planar optical waveguide stemming from the intermodal coupling and dispersion of waveguide modes caused by macroscopic bends and irregularities of the optical waveguide surface has been developed on the basis of pulse intermodal scattering matrix. It is shown that the elements of this matrix are determined at a waveguide segment whose length greatly exceeds the correlation scale of the field of irregularities but is much smaller than the normalization length of waveguide modes and are described by rectangular functions with a duration proportional to the relative velocity of the corresponding modes. The dependences of the pulse intermodal scattering matrix on the intensities of absorption, Rayleigh scattering, and optical signal scattering from waveguide irregularities have been established. It is shown that, at waveguide lengths exceeding the normalization length, the optical signal shape becomes almost stable and can be expressed in terms of the pulse characteristic of an integrating circuit. It has been established that irregularities of the film in a bent optical waveguide lead not only to additional attenuation but also to enhancement of multimode distortion. A matrix method is proposed for taking into account these distortions, which is based on the effect of equalization (scrambling) of the signal energy over the spectrum of the bent waveguide modes. The model developed was used to process the experimental data on the dynamics of a signal in a weakly guiding multimode polymer optical fiber in order to estimate the parameters of attenuation and irregularities of the waveguide surface.     

Compact in-fiber mode adapter based on double-cladding fiber for multimode fiber access networks

A simple method for coupling light from a laser diode (LD) to multimode fiber (MMF) by using a compact in-fiber mode adapter, which is constructed with double-cladding fiber is presented, for the first time. Strong cladding-mode resonance across the thin-thickness inner cladding is used to excite the cladding modes. Principle of proposed mode adapter is theoretically investigated and its performances are experimentally verified by measurement results. By comparing the direct connection between LD and MMF, the coupling efficient of transmission power is improved by using our proposed adapter.     

Widely tunable asymmetric long-period fiber grating with high sensitivity using optical polymer on laser-ablated cladding

We demonstrate high-efficiency, wideband-tunable, laser-ablated long-period fiber gratings that use an optical polymer overlay. Portions of the fiber cladding are periodically removed by CO(2) laser pulses to induce periodic index changes for coupling the core mode into cladding modes. An optical polymer with a high thermo-optic coefficient with a dispersion distinct from that of silica is used on a deep-ablated cladding structure so that the effective indices of cladding modes become dispersive and the resonant wavelengths can be efficiently tuned. The tuning efficiency can be as high as 15.8 nm/ degrees C, and the tuning range can be wider than 105 nm (1545-1650 nm).     

Multi-coupler side-pumped Yb-doped double-clad fiber laser

The side-coupler of angle polished method, using angle-polished multimode fiber and optical adhesive, is used to efficiently pump an Yb-doped double-clad fiber laser. The maximum coupling efficiency of 78.6% is achieved by the side-coupler for a multimode fiber with a circular core of 200 μm and a double-clad fiber with a 350/400 μm D-shaped inner cladding. While laser diodes (LDs) with three side-couplers are simultaneously used as pump sources, maximum output power of 1.38 W and slope efficiency of 48.9% are demonstrated in the fiber laser system.     

Efficient coupler between chip-level and board-level optical waveguides

We propose an efficient optical coupler between a submicrometer-sized silicon waveguide on a silicon photonic chip and a multi-micrometer wide polymer waveguide on an optical printed circuit board for interchip optical networks. We show low coupling loss <0.4 dB with high lateral and angular tolerance to misalignment so that coupling can be done by automatic pick-and-place equipments with high throughput and low cost. The coupler has a wide optical bandwidth from 1470 to 1650 nm.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

Compensation for multimode fiber dispersion by adaptive optics

Adaptive optics is used to compensate for modal dispersion in digital transmission through multimode fiber (MMF). At the transmitter, a spatial light modulator (SLM) controls the launched field pattern. An estimate of intersymbol interference (ISI) caused by modal dispersion is formed at the receiver and fed back to the transmitter, where the SLM is adjusted to minimize ISI. Error-free transmission of 10 Gbit/s non-return-to-zero signals through standard 50 microm graded-index MMFs up to 11.1 km long is demonstrated. It is shown that a single SLM can compensate for modal dispersion across a 600 GHz bandwidth.     

用非球面透镜制作光纤约1:1空间耦合器

针对光纤的泵浦耦合问题,对由两片非球面透镜组成的接近1:1光纤间空间耦合器进行了计算和实验验证.利用高斯光束的变化规律对光路进行了分析研究,并根据二极管输出光相干性不好的特点,对非球面透镜进行了光路追迹的模拟计算.研究发现,在泵浦光波长等因素发生变化时,利用椭球面透镜组成的耦合系统较双曲面透镜有更高的稳定性.实验中选用符合计算结果要求的非球面透镜组成耦合装置,利用一台二极管激光器(尾纤输出端面直径约200 μm,N.A.约0.2)泵浦一段芯径约200 μm(N.A.约0.42)的多模光纤,耦合装置的透过率约95%,在光纤端面有反射的条件下约90%的泵浦光耦合进光纤.     

用非球面透镜制作光纤约1∶1空间耦合器

针对光纤的泵浦耦合问题,对由两片非球面透镜组成的接近1∶1光纤间空间耦合器进行了计算和实验验证.利用高斯光束的变化规律对光路进行了分析研究,并根据二极管输出光相干性不好的特点,对非球面透镜进行了光路追迹的模拟计算.研究发现,在泵浦光波长等因素发生变化时,利用椭球面透镜组成的耦合系统较双曲面透镜有更高的稳定性.实验中选用符合计算结果要求的非球面透镜组成耦合装置,利用一台二极管激光器(尾纤输出端面直径约200μm,N.A.约0.2)泵浦一段芯径约200μm(N.A.约0.42)的多模光纤,耦合装置的透过率约95%,在光纤端面有反射的条件下约90%的泵浦光耦合进光纤.     

基于光纤锥和纤芯失配的Mach-Zehnder干涉湿度传感器

介绍了一种简单且灵敏度较高的Mach-Zehnder干涉湿度传感器.将单模光纤和多模光纤渐变熔接光纤锥,色散补偿光纤被熔接在两个多模渐变光纤之间,形成了单模光纤-光纤锥-多模渐变光纤-色散补偿光纤-多模渐变光纤-光纤锥-单模光纤结构的传感器.光纤锥起到了增加包层模能量的作用,两个多模渐变光纤节点作为光耦合器,从而形成光纤Mach-Zehnder干涉仪.外界环境湿度的变化,将使得传感器透射谱能量发生变化,通过测量干涉谱波峰峰值能量实现对湿度的测量.实验结果表明干涉谱波峰峰值能量与环境湿度之间存在良好的线性关系.当环境湿度在35%RH—85%RH范围内变化,一段由20 mm色散补偿光纤组成的传感器,其灵敏度为-0.0668 dB/%RH,相关度为0.995.该传感器结构紧凑、尺寸小、制造工艺简单,这使其可以被广泛用于湿度测量.     

Mid-infrared supercontinuum and optical frequency comb generations in a multimode tellurite photonic crystal fiber

We numerically investigate the mid-infrared(MIR) supercontinuum(SC) and SC-based optical frequency comb(OFC) generations when the three optical modes(LP01, LP02, and LP12) are considered in a multimode tellurite photonic crystal fiber(MM-TPCF). The geometrical parameters of the MM-TPCF are optimized to support the multimode propagation and obtain the desired dispersion characteristics of the considered three optical modes. When the pump pulse with center wavelength λ = 2.5 μm, width T = 80 fs, and peak power P = 18 k W is coupled into the anomalous dispersion region of the LP01, LP02, and LP12 modes of the MM-TPCF, the-40-d B bandwidth of the generated MIR SCs can be up to2.56, 1.39, and 1.12 octaves, respectively, along with good coherence. Moreover, the nonlinear dynamics of the generated SCs are analyzed. Finally, the MIR SCs-based OFCs are demonstrated when a train of 50 pulses at 1-GHz repetition rate is used as the pump source and launched into the MM-TPCF.