用反Diels-Alder反应合成天然产物XIV. 立体控制合成(±)-环 氧菌素和(±)- 4-表环氧菌素

对苯醌与环戊二烯经Diels-Alder反应保护其一侧的双键,在引入必要的官能团及取代基后,再经反Diels-Alder反应得到(±)-4-表环氧菌素(7),对7进一步进行羟基构型转换而得(±)-环氧菌素(6)总产率分别为70%和65%.     

4,5-环氧-2-戊烯醛的催化加氢

考察了铑、钌、钯络合物对4,5-环氧-2-戊烯醛加氢的催化作用,发现Pd(acac)_2是高效的催化剂,用这一催化体系研究的结果表明:与环氧基因相邻的双键对环氧环有一定的活化作用;溶剂及配体对反应影响很大,加氢速度分别按下列顺序降低:乙酸>乙醇>丙酮>苯>四氢呋喃>环己烷,Pd(tfac)_2≥Pd(hfac)_2>Pd(acac)_2, 此外还考察了压力、温度对反应的影响,提出了包括环氧基参与配位的4,5-环氧-2-戊烯配合醛加氢的可能反应机理。     

4,5-环氧环己烷1,2-二甲酸二缩水甘油酯的固化行为

本文用动态力学扭辨分析法,研究4,5-环氧环己烷1,2-二甲酸二缩水甘油酯与间苯二胺的热固化动态力学行为。结果表明:固化过程分两个阶段进行,低于100℃时,交联反应主要在缩水甘油酯链的环氧基上进行;100—130℃时为酯链环氧基反应趋近完全和酯环环氧基反应速率逐步增大的过渡区;130℃以上固化时,酯环环氧基才明显地参与固化交联反应。从Arrhenius关系曲线求得本固化体系凝胶点前表现反应活化能为13.2kcal/mol。     

手性Salen及Ga(Salen)催化苯基锂对环氧环己烷对映选择性开环反应

合成了14个含1,2-环己二胺、1,2-二苯基乙二胺或邻苯二胺的手性Salen化合物, 研究了手性Salen直接催化苯基锂对环氧环己烷的不对称开环反应, 结果表明二胺的结构和苯环上3,3'-位取代基对反应的对映选择性有很大的影响. 用Salen与 Me₃Ga原位生成的Ga(Salen)催化苯基锂对环氧环己烷的不对称开环反应, 与用Salen直接催化相比, 得到了更好的化学产率和对映选择性. 当用Ga(Slane) 15为催化剂时, 最佳ee值为73%.     

用反Diels-Alder反应合成天然产物XIV. 立体控制合成(±)-环 氧菌素和(±)- 4-表环氧菌素

对苯醌与环戊二烯经Diels-Alder反应保护其一侧的双键,在引入必要的官能团及取代基后,再经反Diels-Alder反应得到(±)-4-表环氧菌素(7),对7进一步进行羟基构型转换而得(±)-环氧菌素(6)。总产率分别为70%和65%。     

含次环己基的有机硅单体及其低聚体的合成

硅氯仿和环己二烯-1,3进行硅氢加成反应,生成1,3-双(三氯硅基)环己烷,经醇解制得1,3-双(三乙氧硅基)环己烷,与溴化甲基镁反应,制得1,3-双(二乙氧甲硅基)环己环、1-(乙氧二甲硅基)-3-(二乙氧甲硅基)环己烷和1,3-双(乙氧二甲硅基)环己烷,它们在盐酸溶液中分别进行水解,得到各种含次环己基的有机硅低聚体,其中2,2,4,4,11,11,13,13-八甲基-3,12-二氧(杂)-2,4,11,13-四硅(杂)三环[11,3,1,1~(5,9)]十八烷和D_4相似,可能经开环聚合得到聚硅次环己基硅氧烷。     

端环氧基聚苯乙烯低聚的物合成与表征

采用阴离子聚合法,以正丁基锂(n-BuLi)为引发剂、乙二醇二缩水甘油醚(EGDE)为封端剂,在常压惰性气体保护下引发苯乙烯(St)聚合,制得端环氧基聚苯乙烯低聚物(PS-ep)。采用GPCI、R和1H-NMR对PS-ep进行表征,并用盐酸-二氧六环银量法测定端环氧基含量。结果表明:以EGDE为封端剂可以使端环氧基摩尔分数(xep)达到0.80左右;升高封端反应温度和延长封端反应时间有利于提高端环氧基的摩尔分数;EGDE与n-BuLi的摩尔比以4∶1为宜。     

螺环三代树形大分子化合物的合成

以对苯二甲醛单缩醛与季戊四醇反应得到了2,4,8,10-四氧杂-2,9-二(4-二氰基乙烯基苯基)螺[5.5]十一烷(1), 经水解, 再与丙二腈反应, 制备了中间体2,4,8,10-四氧杂-2-(4-二氰基乙烯基苯基)-9-(4-甲酰基苯基)螺[5.5]十一烷(3). 8-(4-氧代环己烷基)-1,4-二氧杂螺[4.5]癸烷经芳构化形成2,6,10-三-(4-氧代环己烷基)-1,2,3,4,5,6,7,8,9,10,11,12-十二氢苯并[l]菲(4), 再与甲醛进行羟醛缩合, 制成了2,6,10-三-(4-羟基-3,3,5,5-四羟甲基环己烷基)-1,2,3,4,5,6,7,8,9,10,11,12-十二氢苯并[l]菲(5), 将5与过量的3反应, 得到了目标树形大分子化合物2,6,10-三-{15-(3,11-二(-4-(3-((9-(4-二氰基乙烯基)苯基)2,4,8,10-四氧杂螺[5.5]十一烷基)))-7-羟基-二螺[5.1.5.3]十六烷基)}-1,2,3,4,5,6,7,8,9,10,11,12-十二氢苯并[l]菲(6), 收率为18.1%. 产品结构经IR, 1H NMR, MS和元素分析进行了表征. 对影响反应的因素进行讨论.     

4,5-环氧环己烷1,2-二甲酸二缩水甘油酯/m-PDA固化体系的形态结构及动态力学行为

<正> 不少作者已对一般固化环氧树脂的形态结构作了研究。作者对4,5-环氧环己烷1,2二甲酸二缩水甘油酯(简称TDE-85)树脂固化行为研究的结果表明,由于TDE-85具有两种不同活性的环氧基,固化温度不同,两种环氧基参与开环交联反应程度不相同。本文在不同温度下采用SEM、TBA对TDE-85/m-PDA固化体系并研究其形态结构和相应的动态力学行为。以探讨TDE-85由于化学结构的特殊固化过程与形态结构间的关系。     

环己烷并卟啉的合成及光谱和电化学性质研究

合成了三种在中位上具有不同取代苯基的环己烷并卟啉:5,10,15,20-四(4-甲苯基)环己烷并卟啉,5,10,15,20-四苯基环己烷并卟啉和5,10,15,20-四(4-氯苯基)环己烷并卟啉。利用核磁共振及质谱对它们进行了结构表征,研究了它们在二氯甲烷和吡啶溶剂中的紫外-可见光谱和电化学性质,探讨了卟啉大环周边的取代基和溶剂对化合物的光谱和氧化还原电位的影响,发现β-位上的环己烷取代基对化合物的光谱和电化学性质具有显著的影响。     

Synthesis and characterization of imide ring and siloxane-containing cycloaliphatic epoxy resins

A novel imide ring and siloxane-containing cycloaliphatic epoxy compound 1,3-bis[3-(4,5-epoxy-1,2,3,6-tetrahydrophthalimido)propyl]tetramethyldisiloxane (BISE) was synthesized from 1,3-bis(3-aminopropyl)tetramethyldisiloxane and tetrahydrophthalic anhydride by a two-step procedure, which was then thermally cured with alicyclic anhydrides hexahydro-4-methylphthalic anhydride (HMPA) and hexahydrophthalic anhydride (HHPA), respectively. As comparison, a commercial available cycloaliphatic epoxy 3,4-epoxycyclohexylmethyl-3′,4′-epoxycyclohexane carboxylate (ERL-4221) cured with the same curing agents was also investigated. The experimental results indicated that the BISE gave the exothermic starting temperature higher than ERL-4221 no mater what kind of curing agents applied, implying the reactivity of the former is lower than the latter. The fully cured BISE epoxy resins have good thermal stability with thermal decomposition temperature at 5% weight loss of 346-348 °C in nitrogen, although they gave the relatively low glass transition temperatures due to the presence of flexible propyl and siloxane segments in the epoxy backbone. The BISE epoxy resins exhibited good mechanical and dielectric properties as well as low water absorption. The improved dielectric properties and the reduced water absorption of BISE epoxy resins are attributed to the low polarity as well as the hydrophobic nature of siloxane segment in the epoxy backbone.     

Revealing defects hampering the formation of epoxy networks with extremely high thermal properties: Theory and experiments

We present a combined experimental and theoretical investigation of thermal properties of cycloaliphatic epoxy networks. The networks are prepared from 3,4-epoxycyclohexylmethyl-3,4-epoxycyclohexanecarboxylate ERL-4221 as a monomer and 4-methylhexahydrophthalic anhydride as a curing agent and their glass transition temperature T_g is evaluated by dynamic mechanical and thermal mechanical analyses as well as by differential scanning calorimetry. It is found that the cured epoxy networks have high T_g values reaching 233–238 °C. The method of anharmonic oscillators is first proposed to simulate the effect of network structure on the thermal properties. It suggests that further increase of T_g values is not attained because of the formation of intramolecular cyclic structures. Studies of model reaction by mass-spectrometry confirm the formation of such structures at curing.     

Synthesis and characterization of a novel cycloaliphatic epoxy resin starting from dicyclopentadiene

A novel tri-functional cycloaliphatic epoxy resin was synthesized starting from dicyclopentadiene. The chemical structures of the resultant epoxy resin and its precursor were characterized with FTIR spectroscopy, EEW, ¹H NMR and Mass spectrographic analyses. The thermal and mechanical properties of the resulting polymer were evaluated with differential scanning calorimeter (DSC), thermo-gravimetric and thermal mechanical analysis. Compared to that of the common cycloaliphatic epoxy resin ERL-4221, the cured polymer of the novel epoxy resin exhibited lower thermal degradation temperature with much higher char yield and similar thermal expansion coefficient. These excellent overall performances make it a promising packaging material.     

双官能团液体脂环族环氧化合物的合成与性能

脂环族烯烃类化合物经过环氧化反应制备了三种液体脂环族环氧化合物 ,即 3,4 环氧环己基甲基 2′ ,3′ 环氧环己醚 (Ⅰe ) ,双 (2 ,3 环氧环己基 )醚 (Ⅱe )和双 (2 ,3 环氧环己烷 ) (Ⅲe ) .反应收率大于 80 % .用红外光谱、核磁共振谱、元素分析、环氧当量测定等方法证实了它们的结构 .三种环氧化合物在固化前都具有很低的粘度 (<10 0mPa·s ,2 5℃ ) ,用酸酐类固化剂热固化后得到的交联聚合物具有高的玻璃化转变温度 (Tg=15 0～ 180℃ )、低的线性热膨胀系数 (α1 =6 .0× 10 - 5 ～ 7.6× 10 - 5 ℃ ,α2 =14.5× 10 - 5 ～ 17.0× 10 - 5 ℃ )和较高的储存模量 (E′1 =2 .1～ 3.0GPa ,E′2 =0 .0 2 0～ 0 .0 33GPa) ,它们的总体性能好于国外同类产品ERL 42 2 1.在涂料、电子封装料等方面具有良好的应用前景     

Synthesis and degradable property of novel sulfite-containing cycloaliphatic epoxy resins

Liquid cycloaliphatic diepoxide containing sulfite group (Epoxide-S) was designed and synthesized through the two-step reactions: the nucleophilic substitution between thionyl chloride and cyclohex-3-1-methanol, and the subsequent epoxidation. The chemical structures of the epoxidized product and its olefin precursor were confirmed by FTIR and ¹H NMR spectra. Different from conventional thermosetting epoxy resins, the cured Epoxide-S started to decompose at 185 °C. The apparently lower degradable temperature is desirable for reworkable electronic packaging materials because the dismantlement of waste electronic products or the replacement and repair of faulty chips become convenient. Moreover, after co-curing between Epoxide-S and the commercial cycloaliphatic diepoxide ERL-4221, the thermal degradation temperatures of the copolymers were tunable in the range from 185 to 323 °C by varying the ratio of two monomers. The unique degradation behaviors were investigated by means of computer calculation, thermogravimetric analysis, and FTIR spectra.     

Polymerization of cyclic monomers, 1. Radical polymerization of unsaturated spiro orthocarbonates

7-Methyl-2-methylene- ( 1 ) and 7-methyl-2,3-dimethylene-1,4,6,9-tetraoxaspiro[4.4]nonane (2) were synthesized and characterized by elemental analysis, IR, ¹H NMR and ¹³C NMR spectroscopy. Radical polymerization of the spiro orthocarbonates (SOC) 1 and 2 show that they undergo primarily vinyl polymerization with a low degree of ring-opening reaction. Homopolymerization of 2 at 120°C with di-tert-butyl peroxide gives a transparent crosslinked polymer and the polymerization generates a 12,5% shrinkage in volume.     

Synthesis of an epoxy functionalized spiroorthocarbonate used as low shrinkage additive in cationic UV curing of an epoxy resin

The synthesis of an epoxy functionalized spiroorthocarbonate (SOC) is reported. The obtained monomer has been used a slow shrinkable additive in cationic UV curing of a commercially available dicycloepoxy resin. A polymer network flexibilization was evidenced by increasing the SOC content in the photocurable formulation. It has been demonstrated that SOC acts as shrinkage reduction additive reaching expansion on volume after polymerization in the presence of 10 wt% of the functionalized spiroorthocarbonate.     

Synthesis of copolymers containing a spiro orthocarbonate moiety and evaluation of the volume change during their cationic crosslinking

Spiro orthocarbonate (SOC) monomers having either an exomethylene group {3,3‐dimethyl‐9‐methylene‐1,5,7,11‐tetraoxaspiro[5.5]undecane (ExoSOC)} or an allyl group {9‐allyl‐3,3‐dimethyl‐1,5,7,11‐tetraoxaspiro[5.5]undecane (AllylSOC)} were radically copolymerized with vinyl monomers at several feed ratios to obtain the corresponding copolymers having SOC moieties in the side chain. The obtained copolymers were crosslinked via the double ring‐opening polymerization of the SOC moieties by a treatment with boron trifluoride etherate. The volume changes during the crosslinking of the copolymers were evaluated by density measurements with a gas pycnometer. As the SOC moiety composition increased, the volume shrinkage during the crosslinking was suppressed, and that finally changed into volume expansion. The volume changes during the crosslinking of the copolymers from AllylSOC were slightly larger than those of the copolymers from ExoSOC. The higher volume expansions in the crosslinking of AllylSOC‐based copolymers were ascribable to the lower steric hindrance around the SOC moieties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 7040–7053, 2006     

Spin–orbit coupling in oxygen containing diradicals

Intermediate diradicals which occur in the Paterno–Büchi photocycloaddition and in the Norrish type I photoreactions have been calculated taking into account the spin–orbit coupling (SOC) between the singlet (S) and triplet (T) states. Reaction paths for the photocycloaddition of formaldehyde to ethene and the diradical products of the α-cleavage of cyclohexanone have been optimized by the MNDO CI method for a number of different singlet and triplet states. SOC integrals are calculated by an effective one-electron approximation. Intermediate diradicals in the Paterno–Büchi reaction and the SOC effects are also studied ab initio with CAS SCF geometry optimization in a TZV basis set. Both methods predict a large SOC matrix element between the S and T states in the course of the C–C attack, while the SOC integral is two orders of magnitude smaller for the diradical produced in the C–O attack. In the Norrish type I photoreaction the oxygen atom also produces some nonzero contribution to the SOC integral which governs intersystem crossing in a ·C–C· diradical. For the diradicals produced by the α-cleavage of cyclohexanone a vibronic interaction is responsible for the SOC mixing between the lowest S and T states. The importance of one-center versus two-center SOC contributions in diradicals is briefly discussed.     

二茂铁四氟硼酸盐的阳离子光引发性能的研究

制备并研究了[CpFeCp]BF4作为阳离子光引发剂在高压汞灯下引发环氧类预聚物的光引发活性.发现其在紫外及可见光区均有较强吸收(λm=355nm、620nm);对环氧类预聚物,具有优良的光引发活性,感度值可达41.8mJ/cm2,优于其它的阳离子光引发剂;[CpFeCp]BF4的最佳使用浓度为3%(质量分数)左右,由于光照后仍有强后聚合活性,发现其在较低浓度(质量分数1%)引发后放置,仍可使聚合完全;同其它的阳离子光引发剂相比,[CpFeCp]BF4制备简单,非常有应用价值.